ThermoPro TP65 Wireless Indoor/Outdoor Humidity and Temperature Monitor

Introduction

Congratulations on your purchase of the wireless indoor/outdoor humidity and temperature monitor. This device allows you to monitor outdoor and indoor temperature and humidity from the comfort of your home.

Hints and Tips

If the receiver does not connect to the transmitter, try the following:

• Press and hold the CHANNEL/SYNC button on the base station and then press the TX button on the transmitter.
• Relocate the base station and/or the remote unit until a connection is found.
• Signals from other electronic devices may cause interference. Place the base station and receiver away from these devices.
• The transmitter may not function properly in extreme temperatures due to battery power. Replace the batteries; the unit will resume proper function in more moderate weather.
• If the base station is attached to a refrigerator or a metal object by magnet, the transmission range may be shorter. Remove the base station from the refrigerator or metal object, or place the base station and remote sensor as close as possible.
• If the Humidity is lower than 10%, it will display 'LLL'.

Warnings

• Do not subject the unit to excessive force, shock, dust, temperature, or humidity.
• Do not immerse the unit in water.
• Do not remove any screws.
• Do not dispose of this unit in a fire, as it may explode.
• Keep the unit away from small children, as the unit or parts of it might be a choking hazard.
• Never attempt to recharge the batteries using any other methods.
• Dispose of the unit legally and recycle when possible.

Specifications

Components

• One base station unit (Receiver)
• One remote sensor (Transmitter)

Although the remote sensor is designed to be rainproof, it must always be placed upwards so that rain won't get inside the sensor through the vent holes on the bottom. These vent holes allow the remote sensor to detect environmental temperature and humidity more precisely and quickly.

Indoor Base Station (Receiver) Features

The indoor base station features:

• Large LCD display showing current outdoor and indoor humidity/temperature.
• Battery Compartment: Holds 2 AAA batteries.
• Tabletop and wall-mounted design.
• Indoor Temperature range: -4°F~158°F (-20°C~70°C).
• Humidity range: 10% ~ 99%.
• Temperature display unit: °C and °F selectable.
• Temperature Resolution: 0.1 °C/°F.
• Humidity Resolution: 1%.
• Low battery indication.
• Backlight.

Touch Buttons:

• CHANNEL/SYNC: Press once to display readings from up to 3 outdoor remote sensors. Press and hold to enter synchronization mode.
• MAX/MIN/CLEAR: Touch once to display maximum or minimum temperature and humidity. Press and hold to clear history data.
• °F/°C/History: Press to select °C or °F display. When showing max/min data, touch once to set the record time interval between ALL TIME or 24 hours. Note: ALL TIME and 24 hours represent the time since the last manual clear or battery installation.
• Backlight: Touch once to turn on/off the backlight. The backlight automatically turns off after 15 seconds of inactivity.

Temperature & Humidity Trend Indicators

• ⬆️ indicates an increasing trend.
• ➡️ indicates no change trend.
• ⬇️ indicates a decreasing trend.

Outdoor Remote Sensor (Transmitter) Features

The outdoor remote sensor features:

• TX LED indicator.
• Wall hanging hole.
• TX button: Press to manually send temperature/humidity data to the receiver.
• RESET button: Press once to reset the remote sensor.
• Channel Selector (1, 2, 3): Slide to set the desired channel.
• Battery Compartment: Holds 2 AAA batteries.
• Vent holes for precise detection.
• Rain-proof and wall-mounted design.
• Outdoor Temperature range: -4°F~158°F (-20°C~70°C).
• Humidity range: 10% ~ 99%.

Battery Installation and Setup

1. Open the battery compartment of the remote sensor.
2. Slide the channel selector switch inside the battery compartment to your desired channel (1, 2, or 3).
3. Insert 2 AAA batteries into the remote sensor, observing polarity markings. Replace the battery compartment cover.
4. Open the battery compartment at the back of the base station and insert 2 AAA batteries, observing polarity markings. Replace the compartment door.

Note: Do not mix old and new batteries. Do not mix alkaline, standard (carbon zinc), or rechargeable (nickel cadmium) batteries. For maximum performance, use good quality alkaline batteries. A low battery icon will appear on the base station display when battery power is low.

Synchronize Remote Sensors with the Base Station

Follow these steps to pair and reconnect the base station and remote sensor, especially after replacing batteries or if connection is lost:

1. Position the remote sensor near the base station.
2. After installing batteries in the base station, the RF signal icon (top left of the display) will flash for 3 minutes, indicating synchronization mode.
3. If 3 minutes have passed and the RF signal icon is no longer flashing, press and hold the CHANNEL/SYNC button on the base station for 3-4 seconds until the icon flashes again.
4. Install batteries in the remote sensor, wait a moment, or press the TX or RESET button. The remote sensor's temperature/humidity will appear on the base station display upon successful synchronization.
5. For additional remote sensors (up to 3), repeat the synchronization process for each.
6. If multiple sensors are registered, press the CHANNEL/SYNC button to select a channel for permanent display. Press until a circular arrow icon appears under the channel number to enable auto-scroll mode (changes channel every 5 seconds). Press again until the arrow disappears to stop auto-scrolling.

Note: When synchronizing multiple sensors, the unit may cycle through channels for the first three minutes. After that, you can select a channel or use auto-scroll mode.

Place the Base Station and Remote Sensor

1. Place the indoor base station in a well-ventilated indoor area, away from vents, heating/cooling elements, direct sunlight, windows, doors, or other openings.
2. Place the remote sensor on a flat surface, indoors or outdoors, ensuring it is within transmission range of the base station with minimal obstructions.
3. Both the base station and remote sensor can be wall-mounted.

Note: While the remote sensor is rainproof, it must be placed upwards to prevent rain from entering the vent holes, which are crucial for accurate and quick detection of environmental temperature and humidity.

Maximum & Minimum Recorded Temperature & Humidity

1. Press the MAX/MIN/Clear button once to display the highest recorded indoor and outdoor temperatures/humidity since the last reset (MAX will be shown).
2. Press the button again to display the lowest recorded indoor and outdoor temperatures/humidity (MIN will be shown).
3. To clear and reset the max/min records, press and hold the MAX/MIN/Clear button for 3 seconds while MAX or MIN is displayed.
4. When MAX or MIN is displayed, press the ALL-TIME/24 button once to set the data record time interval between ALL TIME or 24 hours. Note: Both settings refer to the time since the last manual clear or battery installation.

FCC Statement of Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

ThermoPro declares that this product complies with the basic requirements and applicable regulations of the EMC Directive 2014/30/EU. The complete declaration of conformity can be found at: https://itronicsmall.com/eu-declaration-of-conformity/

Disposal

Meaning of the "Dustbin" Symbol:

• Protect our environment: do not dispose of electrical equipment in domestic waste.
• Return unused electrical equipment to provided collection points for disposal.
• This helps avoid potential negative effects of incorrect disposal on the environment and human health.
• This contributes to the recycling and reuse of electrical and electronic equipment.
• Information on disposal can be obtained from your local authority.

CAUTION: Batteries/rechargeable batteries must not be disposed of with household waste!

• Batteries must be removed from the appliance.
• Take spent batteries to the appropriate collection point or dealer.
• Your local authority can provide information about public collection points.

The following symbols may be found on batteries/rechargeable batteries containing hazardous substances:

• Pb = contains lead
• Cd = contains cadmium
• Hg = contains mercury
• Li = contains lithium

Limited One-Year Warranty

ThermoPro warrants this product to be free of defects in parts, materials, and workmanship for one year from the date of purchase. For warranty service, contact Customer Service by phone or email for instructions on packing and shipping the product to ThermoPro. This warranty grants specific legal rights, and other rights may vary by state.

Purchasing Additional Remote Sensors

The model number for additional remote sensors for this unit is TPR65. Sensors can be ordered directly from Amazon or ThermoPro by contacting customer service.

Customer Service

• Telephone: 1-877-515-7797 (USA & Canada only); 44-808-164-1683 (UK)
• Email: service@buythermopro.com
• Hours: Weekdays 8:00 AM - 8:00 PM EST (USA & Canada only); Weekdays 1:00 PM - 12:00 AM CET (UK)