iDatalink - Install Guides
INSTALL GUIDE CFL-AL(RS)-CH5-[ADS-ALCA]-EN DOCUMENT NUMBER 38463 REVISION DATE 20170427 FIRMWARE CFL-AL(RS)-CH5-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) ADS-HRN-CH5 (REQUIRED) CARLINK ASCL2 (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 BEFORE INSTALLATION 1- Connect module to computer 2- Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately) www.idatalink.com WARNING I Install type 1 & 3 require a T-Harness (sold separately). Install type 2 doesn't require a T-Harness. VEHICLE LIST - 1 OF 1 MAKE MODEL RAM JEEP DODGE CHRYSLER 200 300 / 300C Aspen PT Cruiser Sebring Avenger Caliber (with start wire) Caliber Charger Durango Magnum Nitro Ram 1500 Ram 2500 Ram 3500 Ram 3500 chassis cab Ram 4500 chassis cab Ram 5500 chassis cab Commander Compass Grand Cherokee Liberty Patriot Wrangler 4500 chassis cab 5500 chassis cab U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN PAGE 2 OF 19 DOC.: #38463 · 20170427 FEATURES YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS 3X LOCK START/STANDALONE MOD. PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX STARTER CTRL RAP SHUTDOWN CTRL 11-14 2 or 3 · · · · · · · · · · 05-07 1 ·········· 07-10 2 or 3 · · · · · · · · · · 06-10 1 ·········· 07-10 2 or 3 · · · · · · · · · · 08-14 2 or 3 · · · · · · · · · · 07 1 ·········· 07-12 2 or 3 · · · · · · · · · · 06-07 1 ·········· 07-10 2 or 3 · · · · · · · · · · 05-07 1 ·········· 07-11 2 or 3 · · · · · · · · · 07-08 2 or 3 · · · · · · · ·· 07-09 2 or 3 · · · · · · · ·· 07-09 2 or 3 · · · · · · · ·· 07-09 2 or 3 · · · · · · · ·· 08-10 2 or 3 · · · · · · · ·· 08-10 2 or 3 · · · · · · · ·· 06-07 1 ·········· 07-17 2 or 3 · · · · · · · · · · 05-07 1 ·········· 08-12 2 or 3 · · · · · · · · · 07-17 2 or 3 · · · · · · · · · · 07-17 2 or 3 · · · · · · · · · 10 2 or 3 · · · · · · · ·· 10 2 or 3 · · · · · · · ·· www.idatalink.com BOX CONTENTS MODULE 1 2 3 WHITE 4 5 6 1 2 A 3 WHITE 4 5 6 7 B 1 WHITE 2 3 C 1 D BLUE 2 3 BOX CONTENTS - 1 OF 1 6 PIN WHITE CONNECTOR PROGRAMMING BUTTON LED 1 7 PIN WHITE CONNECTOR 10 9 8 7 F 6 BLACK 5 4 3 2 1 3 PIN WHITE CONNECTOR E 4 BLACK 3 DATA PORT 2 (WEBLINK, RF, TELEMATIC) 1 3 PIN BLUE CONNECTOR PAGE 3 OF 19 DOC.: #38463 · 20170427 4 PIN BLACK CONNECTOR 10 PIN BLACK CONNECTOR DATA CABLE 1 DATA CABLE 2 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT 4 PIN BLACK CABLE U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CH5 T-HARNESS (optional accessory sold separately) CH5 T-HARNESS COMPUTER USB PORT CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com TELEMATIC KIT (accessories sold separately) MODULE DATA PORT DATA CABLE 1 12V (+) RED WHITE BLUE BLACK 5 AMPS COMPATIBLE ACCESSORIES - 1 OF 1 RED BLUE BROWN BLACK (NC) CARLINK TELEMATIC KIT (accessories sold separately) MODULE DATA PORT DATA CABLE 1 12V (+) RED BLUE WHITE BLACK 5 AMPS PN 4120260 WHITE RED BLACK CAR CONNECTION VEHICLE OBDII PORT PAGE 4 OF 19 DOC.: #38463 · 20170427 OBDII CONNECTOR 12345678 9 10 11 12 13 14 15 16 U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com CHRYSLER MAKE MODEL TYPE 1 - WIRE CHART - 1 OF 1 YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION 300 PT Cruiser Caliber with start wire Charger Magnum Commander Grand Cherokee Mux 05-07 Starter Mux 06-10 Starter Mux 07 Starter Mux 06-07 Starter Mux 05-07 Starter Mux 06-07 Starter Mux 05-07 Starter C1 Black 5 pin 2 Purple/Brown (MUX) Ignition switch C1 Black 5 pin 4 Pink/DkGreen (+) Ignition switch C1 Black 5 pin 2 Purple/Brown (MUX) Ignition switch C1 Black 5 pin 4 Pink/LtBlue (+) Ignition switch C1 Black 5 pin 2 Purple/Brown (MUX) Ignition switch C1 Black 5 pin 4 Pink/DkGreen (+) Ignition switch C1 Black 5 pin 2 Purple/Brown (MUX) Ignition switch C1 Black 5 pin 4 Pink/DkGreen (+) Ignition switch C1 Black 5 pin 2 Purple/Brown (MUX) Ignition switch C1 Black 5 pin 4 Pink/DkGreen (+) Ignition switch C1 Black 5 pin 2 Purple/Brown (MUX) Ignition switch C1 Black 5 pin 4 Pink/Orange (+) Ignition switch C1 Black 5 pin 2 Purple/Brown (MUX) Ignition switch C1 Black 5 pin 4 Pink/Orange (+) Ignition switch PAGE 5 OF 19 DOC.: #38463 · 20170427 ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ COMPONENT LOCATOR DODGE JEEP U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com MODULE A B C D F E DATA A 1 2 3 4 5 6 B 1 2 3 4 5 6 7 C 1 2 3 D 1 2 3 E 1 2 3 4 F 1 01 GREEN/BLACK- HOOD STATUS (-) INPUT 2 02 BLUE/BLACK (NC) 3 03 RED/WHITE (NC) 4 04 BROWN (NC) 5 05 PURPLE/YELLOW (NC) 6 06 PURPLE/BLACK (NC) 7 07 WHITE (NC) 8 08 BLACK/WHITE (NC) 9 09 GREEN (NC) 10 10 PURPLE/WHITE (NC) TYPE 1 - WIRING DIAGRAM - 1 OF 1 CUT AND INSULATE THE PURPLE WIRE (NEXT TO WHITE WIRE) A1 A2 PURPLE - STARTER (+) OUTPUT GREEN/RED - CONTROL (MUX) OUTPUT B1 STARTER (+) - 04 CONTROL (MUX) - 02 WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH COMPATIBLE ACCESSORY IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. AFTERMARKET HOOD SWITCH (-) PAGE 6 OF 19 DOC.: #38463 · 20170427 VEHICLE IGNITION SWITCH SKIM CONNECTOR SKIM HARNESS 54321 A1 B1 U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com TYPE 2 - WIRE CHART - 1 OF 2 PAGE 7 OF 19 DOC.: #38463 · 20170427 COMPONENT LOCATOR YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION MAKE MODEL CHRYSLER 200 Aspen Sebring Avenger Caliber Durango Nitro CanH CanL 11-14 Mux Ignition 12V CanH CanL 07-10 Mux Ignition 12V CanH CanL 07-10 Mux Ignition 12V CanH CanL 08-14 Mux Ignition 12V CanH CanL 07-12 Mux Ignition 12V CanH CanL 07-10 Mux Ignition 12V CanH CanL 07-11 Mux Ignition 12V DODGE U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 ~ ~ 8 pin 6 White/Orange ~ ~ 8 pin 7 White ~ ~ 8 pin 1 Purple/Brown ~ ~ 8 pin 3 Pink ~ ~ 8 pin 5 Red ~ ~ 8 pin 6 White/Orange ~ ~ 8 pin 7 White ~ ~ 8 pin 1 Purple/Brown ~ ~ 8 pin 3 Pink/Gray ~ ~ 8 pin 5 Red ~ ~ 8 pin 6 White/Orange ~ ~ 8 pin 7 White ~ ~ 8 pin 1 Purple/Brown ~ ~ 8 pin 3 Pink ~ ~ 8 pin 5 Red ~ ~ 8 pin 6 White/Orange ~ ~ 8 pin 7 White ~ ~ 8 pin 1 Purple/Brown ~ ~ 8 pin 3 Pink ~ ~ 8 pin 5 Red ~ ~ 8 pin 6 White/Orange ~ ~ 8 pin 7 White/Pink ~ ~ 8 pin 1 Purple/Brown ~ ~ 8 pin 3 Pink/White ~ ~ 8 pin 5 Red/LtBlue ~ ~ 8 pin 6 White/Orange ~ ~ 8 pin 7 White/LtBlue ~ ~ 8 pin 1 Purple/Brown ~ ~ 8 pin 3 Pink/Gray ~ ~ 8 pin 5 Red ~ ~ 8 pin 6 White/LtGreen ~ ~ 8 pin 7 White ~ ~ 8 pin 1 Purple/Brown ~ ~ 8 pin 3 Pink/White ~ ~ 8 pin 5 Red CFL-AL(RS)-CH5-[ADS-ALCA]-EN (DATA) (DATA) (MUX) (+) (+) (DATA) (DATA) (MUX) (+) (+) (DATA) (DATA) (MUX) (+) (+) (DATA) (DATA) (MUX) (+) (+) (DATA) (DATA) (MUX) (+) (+) (DATA) (DATA) (MUX) (+) (+) (DATA) (DATA) (MUX) (+) (+) Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch Ignition switch ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ www.idatalink.com MAKE MODEL DODGE TYPE 2 - WIRE CHART - 2 OF 2 PAGE 8 OF 19 DOC.: #38463 · 20170427 COMPONENT LOCATOR YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION CanH ~ ~ 8 pin 6 White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Ram Pickup 07-10 Mux ~ ~ 8 pin 1 Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 12V ~ ~ 8 pin 5 Gray/Red (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Compass 07-17 Mux ~ ~ 8 pin 1 Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 12V ~ ~ 8 pin 5 Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Blue (DATA) Ignition switch ~ Liberty 08-12 Mux ~ ~ 8 pin 1 Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 12V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Patriot 07-17 Mux ~ ~ 8 pin 1 Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 12V ~ ~ 8 pin 5 Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/LtBlue (DATA) Ignition switch ~ Wrangler 07-17 Mux ~ ~ 8 pin 1 Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 12V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Orange (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White (DATA) Ignition switch ~ Pickup 10 Mux ~ ~ 8 pin 1 Purple/Brown (MUX) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 12V ~ ~ 8 pin 5 Gray/Red (+) Ignition switch ~ JEEP RAM U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com MODULE A B C D F E DATA A 1 01 GRAY/YELLOW (NC) 2 02 GRAY/RED (NC) 3 03 GREEN/YELLOW (NC) 4 04 GREEN/RED (NC) 5 05 BLUE/YELLOW (NC) 6 06 BLUE/RED (NC) B 1 01 PINK - IGNITION (+) INPUT 2 02 PINK/BLACK (NC) 3 03 ORANGE (NC) 4 04 ORANGE/WHITE (NC) 5 05 ORANGE/BLACK (NC) 6 06 BROWN/YELLOW - CANL 7 07 BROWN/RED - CANH C 1 01 YELLOW - MUX 2 02 YELLOW/RED (NC) 3 03 YELLOW/BLACK (NC) D 1 01 WHITE - 12V (+) 2 02 WHITE/RED (NC) 3 03 WHITE/BLACK - IGNITION (+) OUTPUT E 1 01 BLUE/WHITE (NC) 2 02 WHITE (NC) 3 03 BLACK - GROUND 4 04 RED - 12V (+) 12V (+) REQUIRED WITHOUT COMPATIBLE ACCESSORIES OR 1 2 3 DATA CABLE 4 REQUIRED WITH COMPATIBLE ACCESSORIES F 1 01 GREEN/BLACK- HOOD STATUS (-) INPUT 2 02 BLUE/BLACK (NC) 3 03 RED/WHITE (NC) 4 04 BROWN (NC) 5 05 PURPLE/YELLOW (NC) 6 06 PURPLE/BLACK (NC) 7 07 WHITE (NC) 8 08 BLACK/WHITE (NC) 9 09 GREEN (NC) 10 10 PURPLE/WHITE (NC) U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 TYPE 2 - WIRING DIAGRAM - 1 OF 1 A1 CANL - 07 CANH - 06 MUX - 01 IGNITION (+) - 03 12V (+) - 05 PAGE 9 OF 19 DOC.: #38463 · 20170427 VEHICLE IGNITION SWITCH SKIM CONNECTOR 87654321 A1 WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-) CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com MODULE A B C D F E DATA A 1 2 3 4 5 6 B 1 2 3 4 5 6 7 C 1 2 3 D 1 2 3 E 1 2 3 4 F 1 01 GREEN/BLACK- HOOD STATUS (-) INPUT 2 02 BLUE/BLACK (NC) 3 03 RED/WHITE (NC) 4 04 BROWN (NC) 5 05 PURPLE/YELLOW (NC) 6 06 PURPLE/BLACK (NC) 7 07 WHITE (NC) 8 08 BLACK/WHITE (NC) 9 09 GREEN (NC) 10 10 PURPLE/WHITE (NC) U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 TYPE 3 - WIRING DIAGRAM - 1 OF 1 PAGE 10 OF 19 DOC.: #38463 · 20170427 VEHICLE IGNITION SWITCH A1 SKIM CONNECTOR A2 SKIM HARNESS A1 WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH COMPATIBLE ACCESSORY IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. AFTERMARKET HOOD SWITCH (-) CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com 01 Close driver door. MODULE PROGRAMMING PROCEDURE - STD KEY - 1 OF 1 07 Turn key to OFF position. ACC ON OFF START 02 Re-open driver door to wake up data bus. 08 Remove key. ACC ON OFF START 03 Insert key into ignition. ACC ON OFF START 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. 04 Turn key to ON position. ACC ON OFF START 10 Wait, LED will turn solid GREEN for 2 seconds. 05 LED will turn solid RED. 11 Module Programming Procedure completed. 06 Within 5 seconds, LED will flash GREEN rapidly. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN PAGE 11 OF 19 DOC.: #38463 · 20170427 www.idatalink.com VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 >> NOTE: In Valet Mode, the Remote starter is not >> To exit valet mode: repeat steps 1 to 5. functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 01 Time restriction. Complete next step within 7 seconds. 02 Cycle ignition ON five times [5x OFF/ON] OFF ACC ON START rapidly. ENGINE START STOP 03 Wait, LED 1 will turn solid RED for 2 seconds. 04 Set ignition to OFF position. OFF ACC ON START ENGINE START STOP 05 Valet Mode Programming Procedure completed. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN PAGE 12 OF 19 DOC.: #38463 · 20170427 www.idatalink.com MODULE NAVIGATION PROCEDURE - 1 OF 1 PAGE 13 OF 19 DOC.: #38463 · 20170427 >> It is mandatory to exit the Module Navigation 04 TO ACCESS THE OPTIONS: Press and hold 10 To save and return to the OPTIONS: Press and at the end of this procedure. Failure to exit the programming button until LED 1 turns solid hold programming button until LED 1 turns Module Navigation will drain vehicle battery. RED. solid RED. To exit the Module Navigation at any time: Follow STEP 13. >> Module must be programmed to the vehicle. 05 IN THE OPTIONS: Press the programming 11 LED 1 will flash RED as many times as the [Y] button as many times as the option number [Y] current option number continuously. indicates. LED 1 will flash RED an equal amount of times continuously. >> Use the Module Navigation Chart on the next 06 TO ACCESS THE SETTINGS: Press and hold 12 Configure every other setting and proceed to page. programming button until LED 1 turns solid step 13. GREEN. 01 Set ignition to OFF position. OFF ACC ON START ENGINE START STOP 07 LED 1 will flash GREEN as many times as 13 [Z] the current (or default) setting number, continuously. 02 TO ACCESS THE MENUS: Press and hold 08 IN THE SETTINGS: Press the programming 14 programming button until LED 1 turns solid [Z] button as many times as necessary to access GREEN. your setting. LED 1 will flash GREEN an equal amount of times continuously. 03 IN THE MENUS: Press the programming 09 [X] button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. To return to the MENUS: exit the Module >> Navigation and redo the Module Navigation Procedure. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn OFF. Module navigation completed. Failure to exit the Module Navigation will drain vehicle battery. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com MODULE NAVIGATION CHART - 1 OF 1 PAGE 14 OF 19 DOC.: #38463 · 20170427 [X] MENUS [Y] OPTIONS [Z] SETTINGS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 01 CONFIGURATION 02-07 Technical Support only 01 01 DISARM/UNLOCK BEFORE START 02 01 02 RELOCK AFTER START 02 01 03 RELOCK AFTER SHUTDOWN 02 01 04 FORCE UNLOCK ALL ON FIRST PRESS 02 01 05 TAKEOVER 02 01 02 06 SECURE TAKEOVER DELAY 03 04 01 02 07 FACTORY KEYLESS RS SEQUENCE 03 04 01 02 03 04 08 MODULE RUN TIME 05 06 07 08 01 02 03 04 09 WAIT TO START DELAY 05 06 07 08 10-12 N/A 01 01 N/A 01 OFF ON OFF ON OFF ON OFF ON ENABLE DISABLE* 45 SEC 90 SEC 03 MIN 04 MIN DISABLE N/A LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK 03 MIN 05 MIN 10 MIN 15 MIN 25 MIN 30 MIN 35 MIN 15 MIN 02 SEC 05 SEC 08 SEC 10 SEC 15 SEC 20 SEC 25 SEC 30 SEC N/A N/A CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com REMOTE STARTER ERROR CODES - 1 OF 1 [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES: NOTES I WARNING: The following applies only when the parking 03 lights are connected and supported by the system. 04 II After a remote starter failure, the parking lights will flash 05 [X] number times to indicate an error code. See table. 06 07 08 Foot brake is ON. Hood is open. Engine tach signal is lost. System is in Valet Mode. Vehicle is moving (VSS). Glow plug timeout error. PAGE 15 OF 19 DOC.: #38463 · 20170427 U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com TEST MODULE I DURING PROGRAMMING II DURING REMOTE START III WITH IGNITION OFF MODULE DIAGNOSTICS - 1 OF 1 LED 1 STATUS DIAGNOSTIC Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence. PAGE 16 OF 19 DOC.: #38463 · 20170427 U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.com MODULE RESET PROCEDURE - 1 OF 1 01 Disconnect all connectors from module except 07 Reconnect all connectors. the BLACK 4-PIN connector. 02 Disconnect the BLACK 4-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD programming button while >> Failure to follow procedure may result with a connecting the BLACK 4-PIN connector. DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds. 06 Module RESET completed. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN PAGE 17 OF 19 DOC.: #38463 · 20170427 www.idatalink.com TAKEOVER PROCEDURE - STD KEY - 1 OF 1 >> All vehicle doors must be closed and locked >> Failure to follow procedure will result in prior to remote start sequence. vehicle engine shutdown. 01 Press unlock on OEM or aftermarket remote. 02 Insert key into ignition. ACC ON OFF START 03 Turn key to ON position. ACC ON OFF START 04 Press and release BRAKE pedal. 05 Take over procedure completed. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN PAGE 18 OF 19 DOC.: #38463 · 20170427 www.idatalink.com INSTALLATION CHECKLIST - 1 OF 1 PAGE 19 OF 19 DOC.: #38463 · 20170427 CHECKLIST 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle. 2 Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [1x] on the aftermarket keyfob. ¨ YES: Go to next step. Question 1: Do the doors lock? ¨ YES: Go to next step. ¨ NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock ¨ connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 10 RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question 2: Do the doors unlock? ¨ YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock ¨ connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. ¨ YES: Go to next step. ¨ NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 12 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? ¨ YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch ¨ connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? ¨ YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. ¨ NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? ¨ YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step. ¨ NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? ¨ YES: Go to next step. 13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood ¨ switch, then repeat the test. ¨ NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question 10: Does the vehicle shut down? ¨ YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once ¨ [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 20 Installation checklist completed. ¨ NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. U.S. Patent No. 8,856,780 Automotive Data Solutions Inc. © 2017 CFL-AL(RS)-CH5-[ADS-ALCA]-EN www.idatalink.comFPDF 1.6