ancel AD310 User Manual

1. Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle:

• Always perform automotive testing in a safe environment.
• Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident.
• Wear safety eye protection that meets ANSI standards.
• Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
• Operate the vehicle in a well-ventilated work area: Exhaust gases are poisonous.
• Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
• Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
• Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
• Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
• Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
• Keep the scan tool dry, clean, and free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the scan tool, when necessary.

2. General Information

2.1 On-Board Diagnostics (OBD) II

The first generation of On-Board Diagnostics (called OBD I) was developed by the California Air Resources Board (CARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed. This second generation of On-Board Diagnostic regulations is called "OBD II".

The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specific components and vehicle conditions. When a problem is detected, the OBD II system turns on a warning lamp (MIL) on the vehicle instrument panel to alert the driver, typically by the phrase "Check Engine" or "Service Engine Soon". The system will also store important information about the detected malfunction so that a technician can accurately find and fix the problem. Here below follow three pieces of such valuable information:

1. Whether the Malfunction Indicator Light (MIL) is commanded 'on' or 'Off';
2. Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
3. Readiness Monitor status.

2.2 Diagnostic Trouble Codes (DTCs)

OBD II Diagnostic Trouble Codes are codes that are stored by the on-board computer diagnostic system in response to a problem found in the vehicle. These codes identify a particular problem area and are intended to provide you with a guide as to where a fault might be occurring within a vehicle. OBD II Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The other four characters, all numbers, provide additional information on where the DTC originated and the operating conditions that caused it to be set. Below is an example to illustrate the structure of the digits:

DTC Example: P0520

Systems: P = Powertrain, B = Body, C = Chassis, U = Network

Code Type: Generic (SAE) codes start with P0, B0, C0, U0. Manufacturer Specific codes start with P1, P2, B1, B2, C1, C2, U1, U2.

Sub-systems:

• 1 = Fuel and air metering
• 2 = Ignition system or engine misfire
• 3 = Auxiliary emissions controls
• 4 = Vehicle speed control and idle controls
• 5 = Computer output circuits
• 6 = Transmission controls

The last two digits identify the individual component within the system.

2.3 Location of the Data Link Connector (DLC)

The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic scan tools interface with the vehicle's on-board computer. The DLC is usually located approximately 12 inches from the center of the instrument panel (dash), under or around the driver's side for most vehicles. If the Data Link Connector is not located under the dashboard, a label should be present revealing its location. For some Asian and European vehicles, the DLC is located behind the ashtray, and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle's service manual for its location.

Figure 1-3 Description: The DLC connector (shown on the left) can be found in the area of the car interior seen at the right (indicated by a black arrow). The diagram shows the steering wheel, dashboard center, and ashtray area, with an arrow pointing to the likely location of the DLC behind the ashtray or under the dash.

2.4 OBD II Readiness Monitors

Readiness Monitors are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They run periodic tests on specific systems and components to ensure that they are performing within allowable limits.

Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors) defined by the U.S. Environmental Protection Agency (EPA). Not all monitors are supported by all vehicles, and the exact number of monitors in any vehicle depends on the motor vehicle manufacturer's emissions control strategy.

Continuous Monitors

Some of the vehicle components or systems are continuously tested by the vehicle's OBD II system, while others are tested only under specific vehicle operating conditions. The continuously monitored components listed below are always ready:

1. Misfire
2. Fuel System
3. Comprehensive Components (CCM)

Once the vehicle is running, the OBD II system continuously checks these components, monitors key engine sensors, watches for engine misfire, and monitors fuel demands.

Non-Continuous Monitors

Unlike the continuous monitors, many emissions and engine system components require the vehicle to be operated under specific conditions before the monitor is ready. These monitors are termed non-continuous monitors and are listed below:

1. EGR System - exhaust Gas Recirculation for reducing greenhouse gases.
2. O2 Sensors - monitor and adjust air/fuel mixture.
3. Catalyst - reduces exhaust emissions.
4. Evaporative System - monitors the integrity of the fuel tank system.
5. O2 Sensor Heater - brings O2 sensor to correct operating temperature.
6. Secondary air - reduces exhaust emissions.
7. Heated Catalyst - brings catalyst to correct operating temperature.
8. A/C system - monitors system for freon leaks.

2.5 OBD II Monitor Readiness Status

OBD II systems must indicate whether or not the vehicle's PCM's monitoring has completed testing on each emission component. Components that have been OBD II tested will be reported as "OK". The purpose of recording readiness status is to allow inspectors to determine if the vehicle's OBDII system has tested all the emissions systems. This is useful to know before bringing a vehicle to a state emissions testing facility.

The powertrain control module (PCM) sets a monitor to "OK" after an appropriate drive cycle has been performed. The drive cycle that enables a monitor and sets readiness codes to "OK" varies for each individual monitor. Once a monitor is set as "OK", it will remain in this state. A number of factors, including erasing diagnostic trouble codes (DTCs) with a code reader or a disconnected battery, can result in Readiness Monitors being set to "INC" (incomplete). Since the three continuous monitors are constantly evaluating, they will be reported as "OK" all the time. As long as there are no DTCs stored in memory, the vehicle is running in accordance with the OBD II guidelines. If testing of a particular supported non-continuous monitor has not been completed or not tested, the monitor status will be reported as "INC" (incomplete).

In order for the OBD monitor system to become ready, the vehicle should be driven under a variety of normal operating conditions. These operating conditions may include a mix of highway driving, stop-and-go city driving, and at least one overnight-off period. For specific information on getting your vehicle's OBD monitor system ready, please consult your vehicle owner's manual.

2.6 OBD II Definitions

Powertrain Control Module (PCM): The OBD II terminology for the on-board computer that controls the engine and the drive train.

Malfunction Indicator Light (MIL): The Malfunction Indicator Light (Service Engine Soon, Check Engine) is a term used for the light on the instrument panel. It alerts the driver and/or the repair technician that there is a problem with one or more of the vehicle's systems and may cause emissions to exceed federal standards. If the MIL illuminates with a steady light, it indicates that a problem has been detected and the vehicle should be serviced as soon as possible. Under certain conditions, the dashboard light will blink or flash. This indicates a severe problem, and flashing is intended to discourage vehicle operation. The vehicle onboard diagnostic system cannot turn the MIL off until necessary repairs are completed or the condition no longer exists.

DTC (Diagnostic Trouble Codes): These identify which section of the emission control system has malfunctioned.

Enabling Criteria: Also termed Enabling Conditions. These are the vehicle-specific events or conditions that must occur within the engine before the various monitors will set or run. Some monitors require the vehicle to follow a prescribed "drive cycle" routine as part of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle.

OBD II Drive Cycle: A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the "ready" condition. The purpose of completing an OBD II drive cycle is to force the vehicle to run its onboard diagnostics. Some form of a drive cycle needs to be performed after DTCs have been erased from the PCM's memory or after the battery has been disconnected. Running through a vehicle's complete drive cycle will "set" the readiness monitors so that future faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. For vehicle-specific drive cycles, consult the vehicle's Owner's Manual.

Freeze Frame Data: When an emissions-related fault occurs, the OBD II system not only sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem. This set of values is referred to as Freeze Frame Data and may include important engine parameters such as engine RPM, vehicle speed, air flow, engine load, fuel pressure, fuel trim value, engine coolant temperature, ignition timing advance, or closed loop status.

3. Using the Scan Tool

3.1 Tool Description

The ANCEL AD310 scan tool features the following components:

1. LCD DISPLAY: Indicates test results. It is a backlit, 128 x 64 pixel display with contrast adjustment.
2. ENTER BUTTON: Confirms a selection or action from a menu.
3. EXIT BUTTON: Cancels a selection or action from a menu, or returns to the previous menu. It is also used to exit the DTC Lookup screen.
4. UP SCROLL BUTTON: Moves up through menu and submenu items in menu mode. When more than one screen of data is retrieved, it moves up through the current screen to the previous screens for additional data.
5. DOWN SCROLL BUTTON: Moves down through menu and submenu items in menu mode. When more than one screen of data is retrieved, it moves down through the current screen to the next screens for additional data.
6. OBD II CONNECTOR: Connects the scan tool to the vehicle's Data Link Connector (DLC).

3.2 Specifications

• Display: Backlit, 128 x 64 pixel display with contrast adjustment.
• Operating Temperature: 0 to 60 °C (32 to 140 °F).
• Storage Temperature: -20 to 70 °C (-4 to 158 °F).
• External Power: 8.0 to 18.0 V power provided via vehicle battery.
• Dimensions:
  • Length: 125 mm (5.00")
  • Width: 70 mm (2.80")
  • Height: 22 mm (0.90")
• Weight: NW: 0.23kg (0.51lb), GW: 0.32kg (0.74lb).

3.3 Included

The package includes:

1. AD310 Scan Tool main unit
2. User's Manual

3.4 Language

To change the language:

1. From the Main Menu, use the UP/DOWN scroll button (↑ or ↓) to select "Language" and press the ENTER button.
2. (Screen image description: Shows "Main Menu" with options like Diagnostics, Language, Contrast, Unit of Measure. "Language" is highlighted.)

3.5 Contrast

To adjust the display contrast:

1. From the Main Menu, use the UP/DOWN scroll button (↑ or ↓) to select "Contrast" and press ENTER.
2. (Screen image description: Shows "Main Menu" with options like Diagnostics, Language, Contrast, Unit of Measure. "Contrast" is highlighted.)
3. From the Contrast menu, use the UP/DOWN scroll button (↑ or ↓) to increase or decrease contrast.
4. (Screen image description: Shows "Contrast" with a slider or percentage, e.g., "(40%)", and instructions like "Use ↑ or ↓ to change".)
5. Press ENTER to save your settings and return to the previous menu.

3.6 Unit of Measure

To change the unit of measure:

1. From the Main Menu, use the UP/DOWN scroll button (↑ or ↓) to select "Unit of Measure" and press ENTER.
2. (Screen image description: Shows "Main Menu" with options like Diagnostics, Language, Contrast, Unit of Measure. "Unit of Measure" is highlighted.)
3. From the Unit of Measure menu, use the UP/DOWN scroll button (↑ or ↓) to select the desired Unit of Measure (e.g., Metric or English).
4. (Screen image description: Shows "Unit Of Measure" with options like "Metric" and "English". One is highlighted.)
5. Press the ENTER button to save your selection and return to the previous menu.

4. OBD II Diagnostics

CAUTION: Do not connect or disconnect any test equipment with the ignition on or the engine running.

To perform OBD II diagnostics:

1. Turn the ignition off.
2. Locate the vehicle's 16-pin Data Link Connector (DLC).
3. Plug the scan tool cable connector into the vehicle's DLC.
4. Turn the ignition on.
5. Press ENTER to enter the Main Menu. Use the UP/DOWN scroll button (↑ or ↓) to select "Diagnostics" from the menu.
6. (Screen image description: Shows a prompt "Turn the ignition on Press any key to con." and the "Main Menu" with "Diagnostics" highlighted.)
7. Press ENTER to confirm. A sequence of messages displaying the OBD II protocols will be observed on the display until the vehicle protocol is detected.

If the scan tool fails to communicate with the vehicle's ECU (Engine Control Unit), a "LINKING ERROR!" message will show up on the display. In this case:

• Verify that the ignition is ON.
• Check if the scan tool's OBD II connector is securely connected to the vehicle's DLC.
• Verify that the vehicle is OBD II compliant.
• Turn the ignition off, wait for about 10 seconds, turn the ignition back on, and repeat the procedure from step 5.

4.1 Read Codes

Stored codes are also known as "hard codes" or "permanent codes". These codes cause the control module to illuminate the Malfunction Indicator Lamp (MIL) when an emission-related fault occurs.

Pending Codes are also referred to as "maturing codes" or "continuous monitor codes". They indicate problems that the control module has detected during the current or last driving cycle, but are not considered serious yet. Pending Codes will not turn on the Malfunction Indicator Lamp; they clear from memory after a certain number of drive cycles if the fault does not reoccur.

To read codes:

1. Use the UP/DOWN scroll button (↑ or ↓) to select "Read Codes" from the Diagnostic Menu and press ENTER.
2. (Screen image description: Shows "Diagnostic Menu" with options like Read Codes, Erase Codes, Live Data, View Freeze Frame, I/M Readiness, Vehicle Info. "Read Codes" is highlighted.)
3. Use the UP/DOWN scroll button (↑ or ↓) to select "Stored Codes" or "Pending Codes" from the Trouble Codes menu and press ENTER.
4. (Screen image description: Shows "Trouble Codes" with options like "Stored Codes" and "Pending Codes". One is highlighted.)

If there are no Diagnostic Trouble Codes present, the display indicates "No (pending) codes are stored in the module!". Wait a few seconds or press any key to return to the Diagnostic Menu.

View DTCs and their definitions on screen.

The control module number, sequence of the DTCs, total number of codes detected, and type of codes (Generic or Manufacturer specific) will be observed on the upper-hand corner of the display.

If more than one DTC is found, use the UP/DOWN scroll button (↑ or ↓) as necessary until all the codes have been viewed.

If retrieved DTCs contain any manufacturer-specific or enhanced codes, a message like "Manufacturer specific codes are found! Press any key to select vehicle make!" will prompt you to select the vehicle manufacturer to view DTC definitions. Use the UP/DOWN scroll button (↑ or ↓) to select the manufacturer and then press ENTER to confirm.

(Screen image description: Shows "Select Manufacturer" with a list including FIAT, Ford, GM, Honda, Hyundai, Isuzu. A selection is highlighted.)

If the manufacturer for your vehicle is not listed, use the UP/DOWN scroll button (↑ or ↓) to select "Other" and press ENTER.

4.2 Erase Codes

Notes:

• This function is performed with the key on and engine off. Do not start the engine.
• Before performing this function, make sure to retrieve and record the trouble codes.
• After clearing, you should retrieve trouble codes once more or turn the ignition on and retrieve codes again. If there are still some trouble codes for hard issues, please find the reason causing the trouble code first, and then solve the problem. Only then can the trouble codes be erased.

To erase codes:

1. Use the UP/DOWN scroll buttons (↑ or ↓) to select "Erase Codes" from the Diagnostic Menu and press ENTER.
2. (Screen image description: Shows "Diagnostic Menu" with "Erase Codes" highlighted.)
3. A warning message comes up asking for your confirmation: "Erase trouble codes! Are you sure?". Select YES or NO.
4. (Screen image description: Shows "Erase codes" prompt with "YES" and "NO" options.)
5. Press ENTER to confirm.
6. If the codes are cleared successfully, an "Erase Done!" confirmation message is displayed.
7. (Screen image description: Shows "Erase codes" with "Erase Done! Press any key to con.".)
8. If the codes are not cleared, then an "Erase Failure. Turn Key on with Engine off!" message is displayed.
9. (Screen image description: Shows "Erase codes" with "Erase Failure. Turn Key on With Engine off! Press any key to con.".)

4.3 Live Data

The OBD II Scan Tool is a special diagnostic tool that communicates with the vehicle's computer. The Scan Tool allows you to view "real-time" Live Data. This information includes values (volts, RPM, temperature, speed, etc.) and system status information (open loop, closed loop, fuel system status, etc.) generated by the various vehicle sensors, switches, and actuators.

To view live PIDs:

1. Press ENTER.
2. Use the UP/DOWN scroll button (↑ or ↓) for more PIDs if an arrow appears on the screen.
3. (Screen image description: Shows "Live Data" with various parameters like DTC_CNT, FUELSYS1, LOAD_PCT(%), ETC(°C), SHRTFT1(%), RPM(/min) and their values. An arrow indicates more data is available.)
4. If you want to change the unit of measure, press ENTER to change.
5. (Screen image description: Shows "Live Data" again, possibly with different units or parameters.)
6. Press EXIT to return to the Diagnostic Menu.

4.4 View Freeze Frame

When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. View Freeze Data is a snapshot of the operating conditions at the time of an emission-related fault.

If DTCs were erased, View Freeze Data may not be stored in vehicle memory, depending on the vehicle.

Select [View Freeze Frame], and the screen will display the interface as shown below:

(Screen image description: Shows "View Freeze Frame" with parameters like DTCFRZF, FUELSYS1, LOAD_PCT(%), ETC(°C), SHRTFT1(%), RPM(/min) and their values. An arrow indicates more data is available.)

Use the UP/DOWN scroll button (↑ or ↓) for more PIDs if an arrow appears on the screen. Press EXIT to return to the Diagnostic Menu.

4.5 I/M Readiness

I/M refers to Inspection and Maintenance, which is legislated by the Government to meet federal clean-air standards. I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.

The purpose of the I/M Readiness Monitor Status is to indicate which of the vehicle's Monitors have run and completed their diagnosis and testing (as described in 2.5), and which ones have not yet run and completed testing and diagnosis of their designated sections of the vehicle's emissions system.

The I/M Readiness Monitor Status function can also be used (after a repair for a fault has been performed) to confirm that the repair has been performed correctly, and/or to check for Monitor Run Status.

Select [I/M Readiness Test] and Press [ENTER]. The screen will display the interface as shown below:

(Screen image description: Shows "Diagnostic Menu" with "I/M Readiness" highlighted. Then shows "Since DTCs Cleared" with MIL Status, Misfire Monitor, Fuel System Mon, Comp. Component, Catalyst Mon, Htd Catalyst and their status like OFF, N/A, OK.)

Press EXIT to return to the Diagnostic Menu.

4.6 Vehicle Info.

Select [Vehicle Info.] and press [ENTER]. The screen will display information such as VIN (Vehicle Identification Number), CID (Calibration ID), and CVN (Calibration Verify Number).

To access vehicle information:

1. Use the UP/DOWN scroll button (↑ or ↓) to select "Vehicle Info." from the Diagnostic Menu and press ENTER.
2. (Screen image description: Shows "Diagnostic Menu" with "Vehicle Info." highlighted.)
3. An advisory message comes up to remind you: "Turn key on, with Engine off! Press any key to con.". Wait a few seconds or press any key to continue.
4. (Screen image description: Shows "Vehicle Info." with the advisory message.)
5. Wait a few seconds while the scan tool reads vehicle information.
6. (Screen image description: Shows "Vehicle Info." with "Reading Info... - Please Wait - ".)
7. Press EXIT button to return to the Diagnostic Menu.

5. Warranty and Service

5.1 Limited One Year Warranty

THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE ANCEL AD310 PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER'S BUSINESS.

The ANCEL AD310 electronic product is warranted against defects in materials and workmanship for one year (12 months) from the date of delivery to the user.

This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and ANCEL AD310 shall not be liable for any consequential or incidental damages.

Final determination of defects shall be made by ANCEL AD310 in accordance with procedures established by ANCEL AD310. No agent, employee, or representative of ANCEL AD310 has any authority to bind ANCEL AD310 to any affirmation, representation, or warranty concerning ANCEL AD310 automotive meters, except as stated herein.

5.2 Service Procedures

If you have any questions, please contact your local store, distributor, or visit the website at www.ancel AD310.com.

If it becomes necessary to return the scan tool for repair, contact your local distributor for more information.