Spider Farmer Compressor Dehumidifier User Manual
Control the Humidity, Boost the Bounty
Precautions for Use
For optimal performance and safety, adhere to the following guidelines:
- After unboxing, allow a 24-hour upright rest period before plugging in to prevent potential damage.
- During use, ensure the product is positioned upright to prevent internal damage.
- Always prioritize safety by reading and retaining the instruction manual and restricting usage to indoor environments only.
- Follow provided instructions meticulously for both installation and operation.
- Before cleaning the dehumidifier, turn off the power and unplug it from the outlet.
- Do not place the machine near heat or flammable materials.
- Do not insert fingers or any objects into the air inlet or outlet.
- Always keep the machine on level surfaces; avoid placing it on uneven or sloping ground.
- Do not spray water, insecticides, or flammable liquids on the unit.
- This machine should not be placed in a confined or narrow space.
- When using the dry clothes function, keep clothes at least 15.7 inches (40 cm) away from the air outlet to prevent water from entering the machine and causing damage.
- The machine's power wiring must comply with national wiring rules, and the power line should be connected to a reliable external ground wire.
- Model specification for the safety tube: 3.15A. This dehumidifier is designed to operate in an environment between 41°F (5°C) and 95°F (35°C).
- When using the dehumidifier, ensure that other objects surrounding the machine are at least 7.9 inches (20 cm) away.
- Children should be supervised to ensure they do not play with the appliance.
- This appliance is not intended for use by individuals (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Package Contents
- Dehumidifier (with power Cord) x 1
- Connecting components x 1
- Air duct x 1
- Temp/humidity sensor wire x 1
- Drain pipe x 1
Front View: Control Panel, Air Outlet, Water Tank, Water Level Window
Back View: Handle, Air Intake, Drain Hose Outlet, Plug Holder
How to Install
Understand the two drainage modes: Intermittent Drainage Mode and Continuous Drainage Mode.
Intermittent Drainage Mode: The water tank must be manually emptied when full, as indicated by an alarm. This mode does not require a drainage pipe.
Continuous Drainage Mode: Water is directed through a drain pipe inserted into the dehumidifier's outlet. Refer to Step 5 for setup.
- Step 1: Carefully remove the dehumidifier from its packaging. Ensure all shipping materials are completely removed from the unit. WARNING: Always keep the product upright.
- Step 2: Install the connecting component onto the dehumidifier.
- Step 3: Attach one end of the air duct to the connecting component, and connect the other end to your grow tent. WARNING: Do not direct the air duct toward the plants; avoid blowing air directly onto them. Do not block the product's air intake or exhaust ports.
- Step 4: Insert the external cable of the humidity sensor into the connector. Position the humidity sensor probe where it best represents the humidity levels experienced by the plants.
- Step 5: Open the drain cover, remove the soft rubber plug, and store it safely. Insert the water pipe into the continuous drainage port. Position the end of the water pipe at the drainage location you have arranged. Ensure the water outlet of the pipe is at least 3.9 inches (9.9 cm) lower than the continuous drainage port. Additionally, ensure the water pipe remains straight and free of bends. NOTE: The diameter of the continuous drain port is 16 mm (0.63 inches).
Program Settings
| Setting | Description |
|---|---|
| Mode Setting | Three modes are available: Dry Clothes Mode, Dehumidify Mode, and Continuous Dehumidify Mode. Press the [Mode] button to cycle through the modes: drying, dehumidifying, and continuous dehumidifying. Dry Clothes Mode: Humidity and fan speed cannot be adjusted. Dehumidify Mode: Humidity and fan speed can be adjusted. Continuous Dehumidify Mode: Humidity cannot be adjusted, but fan speed can. |
| Humidity Setting | Humidity levels are adjustable from 30% RH to 80% RH in 5% increments. Upon startup, the device automatically detects and displays room humidity. In Dehumidify Mode, press the [Dehumidify] button to adjust the humidity in 5% increments. The display flashes to indicate the setting mode and shows the selected humidity once set. If no operation occurs for 5 seconds, the display returns to showing the actual room humidity. The dehumidifier starts or stops automatically based on the set humidity level. At 30% RH, the dehumidifier operates in continuous dehumidifying mode. |
| Timer Setting | Allows setting a timer for automatic machine operation. Press the [TIMER] button to set a timer in 1 hour increments, up to 24 hours. The timer countdown starts upon activation. Press and hold the [TIMER] button for faster timer selection. Invalid Time: If the timer is set to "00," it is considered invalid. Upon successful timer setting, the "o" indicator light illuminates. The LED screen displays the set time for several seconds before showing the current humidity. |
| Lock | Press and hold the [LOCK] button for 3 seconds while the unit is turned on to lock the control panel and buttons. Repeat the process to unlock the control panel. |
| Speed Button | Controls fan speed, offering High or Low options: High: Enhances moisture removal and is ideal for maximum dehumidification. Low: Provides quieter operation once the desired humidity level is reached. |
| Power-Off Memory Function | Upon powering on, the device automatically restores its previous working state. In case of a power interruption: If the device was ON, the parameters and settings are retained when power resumes. If the device was OFF, it remains off when power resumes. |
| Overflow Protection | Automatically shuts off the machine when the water bucket is full. The "!" indicator light flashes, and the buzzer alarms briefly. After emptying the water bucket, the indicator light turns off, and the machine resumes operation. |
| Auto Defrost Function | The system automatically detects frost when operating at lower temperatures. If frost is detected, the machine initiates an automatic defrosting process: Defrost Action: The compressor stops, and the fan operates at high speed to aid in defrosting. Defrost Status Display: During defrosting, the "o" power button flashes to indicate the process. |
Status Descriptions Display
Control Panel Indicators:
- Power: "POWER" Button - Lights up when the device is in standby (power off) status.
- Timer: Timer Indicator ("o") - Lights up when the timer is properly set; turns off when the timer is not set.
- Lighting: Lighting Button ("o") - Lights up when the light function is activated; turns off when not in use.
- High-speed: High-Speed Indicator ("o") - Lights up when the unit is set to high-speed fan mode.
- Low-speed: Low-Speed Indicator ("o") - Lights up when the unit is set to low-speed fan mode.
- Dry Mode: Dry Mode Indicator ("o") - Lights up when Dry Clothes Mode is selected; turns off otherwise.
- Dehumidify Mode: Dehu Mode Indicator ("0") - Lights up when the unit is set to dehumidify mode; turns off otherwise.
- Continuous Dehumidification Mode: Con Mode Indicator ("o") - Lights up when Continuous Dehumidification Mode is selected; turns off otherwise.
- Water Full: Water Full Light Indicator (":") - Flashes when the water tank or bucket is full.
- Working Data Display: Displays the humidity value when the device is operating.
Troubleshooting
Before starting the machine, ensure the air outlet is open to prevent overheating. Do not unplug the power cord directly to stop the machine.
| Fault | Possible Cause | Solution |
|---|---|---|
| Humidity Shows "25%RH" | Humidity sensor failure | Set the humidity to 30%RH. Repair or replace the humidity sensor. |
| Humidity Shows "99%RH" | Water on the surface of the humidity sensor Possible humidity sensor failure | Remove water from the humidity sensor. Repair or replace the humidity sensor. |
| Dehumidifier Does Not Work | Power Cord Unplugged | Ensure the unit's plug is properly inserted into the power outlet. |
| Full Tank Indicator Blinking | Empty the water tank and reposition it correctly. | |
| Room Temperature Out of Range | Ensure the room temperature is within the specified range (41°F/5°C to 95°F/35°C). | |
| Defrosting Process Active | At lower ambient temperatures, the machine will defrost automatically. Wait until the process finishes, and the unit will resume dehumidifying. It is normal for the compressor to stop during defrosting. Wait for the process to complete, and the dehumidifier will restart. | |
| Dehumidifier Does Not Dry the Air | Room Humidity at Preset Level | Adjust the humidity setting to 5% lower than the room humidity or set it to 30%RH. Once the room humidity matches the preset level, the dehumidifier enters Standby Mode. |
| Prevention of Frequent Start Function | If the machine just stopped, wait at least 3 minutes before restarting. | |
| Low Room Humidity | The dehumidifier is designed to work in a humidity range of 30%-80%. | |
| Dirty Air Filter / Obstructed Air Inlet or Outlet | Clean the air filter. Remove any obstruction. | |
| Dehumidifier Size Too Small / Poor Air Circulation | Use additional dehumidifiers or upgrade to a higher-capacity unit. Ensure at least 7.9 inches (20 cm) of space around the unit for proper airflow. | |
| Insufficient Time to Remove Moisture / Improperly Sealed Room | Allow the unit at least 3-4 days to maintain the desired relative humidity (RH), especially when first installed. Ensure all doors, windows, and openings are securely closed. | |
| Clogged Air Filter / Improper Filter Installation | Wash and clean the filter. Remove the filter's packaging and ensure it is installed correctly. | |
| Low Room Temperature (Below 41°F/5°C) | Wait until the temperature rises above 5°C for optimal operation. | |
| Loud Noise During Operation | Unit Not Positioned Level | Move the dehumidifier to a flat, horizontal surface. |
| Blocked Air Inlet or Outlet / Clogged Air Filter / Improper Filter Installation | Clear any obstructions. Ensure the air filter is clean and correctly installed. Remove the filter's packaging and ensure it is installed correctly. | |
| Set to Continuous Mode | Avoid setting the humidity too low. A range of 40%-50% is typically sufficient. | |
| High Room Humidity | Adjust the humidity settings or switch to a higher-capacity dehumidifier. | |
| Continuous Operation | Ensure all openings are securely closed. | |
| Water Overflow on the Floor | Stuck Float in Water Tank / Dislodged Magnet on Float / Loose Hose Connection / Improper Water Tank Installation | Adjust the float to allow free movement. Reposition the magnet correctly. Tighten the hose connection at the drain outlet. Reinstall the water tank securely. |
How to Empty the Tank
When the water tank is full, the full tank indicator light will illuminate. The dehumidifier will automatically shut off until the water tank is emptied and replaced. (In Continuous Drainage Mode, the collected water will be drained through the pipe, bypassing the need to empty the tank.)
- Step 1: Pull the water tank out from the bottom using your hand.
- Step 2: Pour the water out through the holes on the side of the water tank lid.
- Step 3: Place the water tank back into position. The full tank indicator will turn off once it is correctly reinstalled.
Notes:
- Float in the Water Tank: Do not remove the float from the water tank. If the float is removed, the sensor may fail to detect the water level accurately, potentially causing water to overflow.
- Cleaning the Water Tank: 1. If the water tank is dirty, use cold or warm water to clean it. 2. Avoid using detergent, steel wool, chemically treated dust cloths, gasoline, benzene, thinner, or other solvents to prevent damage or leakage.
- Placing the Water Tank: When replacing the water tank, press it firmly into position. Improper placement may affect sensor operation or compromise overflow protection.
How to Clean and Maintain
Warning:
- Before cleaning, turn off the dehumidifier.
- Unplug the unit from the wall outlet to ensure safety during cleaning.
A: Cleaning the Dehumidifier Body
Use only a soft, slightly damp cloth or textile for cleaning purposes. Avoid abrasive materials or harsh chemicals.
B: Cleaning the Filter
- Step 1: Pull out the filter.
- Step 2: Clean the filter: Use a vacuum cleaner to gently remove dust from the surface of the filter. If the filter is very dirty, rinse it with warm water and a mild detergent. Allow it to dry completely before reinstalling.
- Step 3: Slowly reinsert the filter back into the unit.
C: Storing the Dehumidifier
- Empty the water tank.
- Roll up the power cord and secure it with a tie to prevent tangling.
- Clean the filter as described above.
- Place the dehumidifier in a cool and dry environment for storage.
Dehumidifier and Smart Control System Integration
How to Use with GGS Controller Kits
- Connect the dehumidifier to the DEV1 or DEV2 port of the GGS Smart Controller using an RJ12 cable. Once successfully connected, you can control the fan speed and running time of the dehumidifier through the GGS Controller.
- Switch the GGS Controller to the equipment control interface.
- Locate the dehumidifier and click the knob to enter its control interface.
Available Modes: Manual Mode, Time Period Mode, Cycle Mode, Environment Mode (Humidity Mode)
Note: Once the dehumidifier is controlled by the GGS Controller, pressing buttons on the dehumidifier itself will be disabled, except for waking up the indicator and screen. The cloud icon on the display will light up.
How to Use with Power Strip Kits (AC5/AC10)
- Connect the dehumidifier to the DEVICE port of the Power Strip using an RJ12 cable. Once successfully connected, you can control the fan speed and running time of the dehumidifier through the Spider Farmer APP.
Available Modes: Manual Mode, Cyclic Mode, Time Period Mode, Ambient Mode (Humidity Mode)
Warranty Information
Spider Farmer offers warranty services in the United States, Canada, United Kingdom, European Union, and Australia.
30-Day Return Policy: Returns or exchanges are accepted within 30 days of delivery if the product is in its original condition. Shipping costs are covered by Spider Farmer.
2-Year Warranty: Within 1 Year: Free repair or replacement for product defects. Customers cover all shipping costs. 1 to 2 Years: Customers are eligible for free accessories or trade-in allowances. Repair services are available, and all costs, including parts and shipping, are borne by the customer.
Note: Unauthorized repairs, modifications, or improper use will void the warranty.
Exclusions: The warranty does not cover misuse, abuse, or normal wear and tear, such as scratches.
Limitation of Liability: Spider Farmer is not responsible for consequential or incidental damages.
Spider Farmer App: Download the app for Android and iOS devices.
