Yale Digital Door Lock User Guide YDM4109+

MUST READ

• This Product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications.
• All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
• This product (YDM4109+) is a Security Enabled Z-Wave Plus Product.
• Security Enabled Z-Wave Controller must be used in order to fully utilize this product.
• Network Module Setting: This setting becomes available through the Main Menu and allows the lock to connect with Controllers.

Reset locally: Z-Wave Module exclusion

Please use this procedure only when the network primary controller is missing or otherwise inoperable.

Note: The door lock could be initialized by pressing of '0' key due to a mistake of user, so, '0' has not been intentionally displayed to prevent the door lock from initializing.

You can find the Security 2 DSK information on the product as shown below:

zws2dsk: 46249-42352-03523-40600-59887-53699-31945-13463 sn:U121M180700001xx

Association Command Class

Association Group

• This product supports ONE association Group.
• Group is the Lifeline Group.
• It can contain up to 1 nodes.

S2 Security CCs and security level

Configuration Command Class

Set the language of the Door Lock interface

Front body

(Front Body, Installation on the outside of the door)

Components:

• 1: Fingerprint Operation Lamp
• 2: Keypad (10-Key)
• 3: Dead Bolt Jam Lamp
• 4: Lever
• 5: Fingerprint Cover
• 6: Battery Change Lamp
• 7: Reset button
• 8: Emergency Key
• 9: Emergency Power Supply Terminal
• 10: Emergency Cover

Pull down Emergency Cover:

The diagram shows the emergency cover being pulled down, revealing the reset button (7), emergency keyhole (8), and emergency power supply terminal (9). A 9V emergency battery is optional.

Main body

(Main Body, Installation on the inside of the door)

Components:

• 1: Battery Cover
• 2: Registration button
• 3: Lever
• 4: Manual thumb turn
• 5: Internal Forced Lock Switch
• 6: 1.5V AA Alkaline Batteries (4EA)
• 7: Slot for Remote control module (Option)
• 8: Volume Control Switch
• 9: Auto / Manual Lock button
• 10: Safe handle button

The diagram illustrates the main body of the lock, including the battery compartment, various buttons and switches, and its connection to the lock case.

Register Controller

Procedure:

1. Enter Master Code.
2. Press the [I] button.
3. Enter [9], [#] buttons.
4. Enter [1], [#] buttons to register controller.
5. Register Controller followed by press [#] button to complete after beep sound from digital door lock.
6. Press [*] button to continue.
7. Press [I] button to complete.

Alternative completion: Press [I] button to complete.

Delete Controller

Procedure:

M PIN 1-9 Controller # 3 Delete # PIN Master Code # * Continue

Complete

Resetting Lock to Factory Default

When the lock is reset to factory defaults, all user codes (including the Master Code) are deleted, and all programming features are reset to original default settings.

1. Remove the battery cover and batteries.
2. Remove the interior escutcheon to access the reset pads.
3. The reset pads are located on the bottom of the PCB board.
4. While pressing the reset pads with tweezers, reinstall batteries and release reset pads with tweezers.
5. Replace the battery cover.

Upon reset, the Master Code creation is the only option available and must be performed prior to any other programming of the lock.

The diagram shows the location of the reset button on the PCB board.

User Code Registration (4~10 digits)

Procedure:

1. Press the [I] button.
2. Enter New User Code.
3. Press the [I] button to complete.

User Fingerprint Registration (Up to 20ea)

Procedure:

1. Press the [I] button.
2. After opening the cover, swipe your finger 3 times through the fingerprint sensor, followed by the voice guide.
3. Press [*] button to continue.
4. Press [I] button to complete.

Unlocking Door with Code

Procedure:

1. Touch the keypad of the Front Body with your palm.
2. Enter the registered Code on the keypad.
3. Touch the keypad of the Front Body with your palm.
4. Enter the [*] button.

Unlocking Door with Card Key

Procedure:

1. Contact registered Card Key.