MIBOXER X1 DMX512 Master (Single Color)

1. Features

• Accord with standard DMX512 protocol.
• Output DMX512 signal and wireless 2.4G signal; More flexible application.
• Support 4 channels control.
• Support multi DMX512 master to control same decoder (Note: need same type DMX512 master).
• Button with sound and LED indicating lamp.
• This product can be controlled by Mi-Light/Miboxer RF remote, and smartphone (need WL-Box1 WiFi gateway).
• This product can be used as RF remote to control MiBoxer 2.4GHz lamps.

2. Parameters

3. Connection Diagram

Input: AC100~240V 50/60Hz (L, N terminals)

DMX512 Master (Model X1): Features DMX IN/OUT ports (D+, D-, GND). Physical dimensions: 86mm x 86mm, 17mm x 9mm.

D1-CX Decoder: Features INPUT, OUTPUT, V-, V+, Power input (DC12V/24V) ports.

Connections:

• DMX512 Master D+ connects to Decoder D+.
• DMX512 Master D- connects to Decoder D-.
• DMX512 Master GND connects to Decoder GND.
• Decoder V+ connects to Single Color LED Lamp V+.
• Decoder V- connects to Single Color LED Lamp V-.
• Decoder Power input connects to DC12V/24V power supply.

Default DMX512 Addresses for Decoders:

• Zone 1: 001
• Zone 2: 002
• Zone 3: 003
• Zone 4: 004

The diagram illustrates the DMX512 Master unit connected to multiple D1-CX Decoders, which in turn power Single Color LED Lamps.

4. Function of Keys

Remark: When touching the buttons, the LED indicator lamp will flash once with a different sound. The touch slider has no sound.

• Dimming Slider: Touch to change brightness from 1% to 100%.
• Master ON: Touch to turn on all linked lights. Long press 5 seconds to turn ON the indicating sound.
• 60S Delay OFF: When the light is ON, press this button to turn the light OFF automatically after 60 seconds.
• Master OFF: Touch to turn off all linked lights. Long press 5 seconds to turn OFF the indicating sound.
• Zone ON: Touch to turn on zone-linked lights.
• Zone OFF: Touch to turn off zone-linked lights.

5. DMX512 Master as RF Remote Instruction

Use as a remote to control MiBoxer 2.4GHz series lamps.

Linking Instructions:

1. Switch off the light. After 10 seconds, switch it on again.
2. When the light is on, short press the [Link/Unlink] button 5 times within 3 seconds.
3. The light blinking 10 times quickly indicates successful linking.

Note: Unlinking must be performed for the same zone as linking.

Unlinking Instructions:

1. Switch off the light. After 10 seconds, switch it on again.
2. When the light is on, short press the [Link/Unlink] button 3 times within 3 seconds.
3. The light blinking 3 times slowly indicates successful unlinking.

Note: If the light does not blink as described, the unlinking failed. Switch off the light again and follow the steps above.

The diagram shows the DMX512 Master unit with [Power] and [Link/Unlink] buttons, and its input/output ports, indicating its operation as a 2.4GHz RF remote.

6. DMX512 Master used as RF Receiver Instruction

The DMX512 Master can receive RF remote signals and transform them into DMX control signals to control lamps.

Note: When using an RF remote to control the DMX512 Master, the RF remote needs to be linked to the master. After linking, RF remote channels 1-4 correspond to DMX512 Master channels 1-4.

Linking Instruction:

1. Long press the [4th channel button] for 5 seconds until the DMX512 Master's indicating lamp blinks quickly.
2. Short press any [channel button] one time. The DMX512 Master's indicating lamp will blink 3 times slowly upon successful linking.

Unlink Instruction:

Long press the DMX512 Master's [4th channel button] for 5 seconds until the DMX512 Master's indicating lamp blinks 10 times fast, indicating successful unlinking.

Compatible with these remote controls (Purchased separately):

• WL-Box1 (2.4GHz Gateway)
• FUT006
• FUT007

7. Installation/ Dismantlement

Installation:

1. Install the bottom case into the wall. Standard bottom cases are shown.
2. Fix the controller base onto the bottom case using screws.
3. Click the upper side of the glass panel onto the controller base, then press the lower side slightly to secure it into the controller base.

Dismantlement:

Insert a screwdriver into the bayonet slot below and gently pry upwards to dismantle the controller.

Diagrams illustrate wall mounting, screw fixing, and panel attachment for installation, and a screwdriver being used for removal.

8. Attention

⚠️ The product shall be debugged and installed by professionals. During installation, ensure that the power is cut off to avoid electric shock by wrong operation.

⚠️ Please check whether the input voltage meets the product voltage requirements.

⚠️ Before switching on the power, please ensure that all wiring is correct, so as not to cause damage to the DMX512 Master.

⚠️ If there are faults, non-professionals should not attempt repairs without permission, otherwise the device may be damaged.