User Manual for better bathrooms models including: BeBa_24911, BeBa_26880, BeBa_24911 BeBa_26880 Wall Mounted Intelligent Toilet, BeBa_24911 BeBa_26880, Wall Mounted Intelligent Toilet, Mounted Intelligent Toilet, Intelligent Toilet
File Info : application/pdf, 36 Pages, 3.05MB
DocumentDocumentWALL MOUNTED INTELLIGENT TOILET BeBa_24911 BeBa_26880 REMOTE CONTROL IPX4 INGRESS PROTECTION REAR AND FRONT WASH 236E400-E71-01K 26.11.2024 CONTENTS SAFETY INFORMATION 3 UNIT MEASUREMENTS 5 PARTS LIST 7 PRODUCT OVERVIEW 8 BEFORE INSTALLATION 9 INSTALLATION 10 REMOTE CONTROL 17 OPERATION 18 CLEANING AND MAINTENANCE 24 REPLACING THE FILTER 25 DRAINING THE WATER TANK 26 TROUBLESHOOTING 27 SUPPORT 28 TECHNICAL SPECIFICATIONS 29 2 SAFETY INFORMATION This manual must be read and fully understood before installing or using the appliance. This product must not be operated without a connected water supply. Installation must be in accordance with all relevant local regulations applicable at the time of installation. It must be installed by a qualified professional to in accordance with BS 7671. If electrical work is carried out within the bathroom which involves addition or alteration of existing circuits, it may be notifiable to your local building control department (Part P). If unsure, professional advice should be sought. The toilet must be fitted in accordance with the Water Supply (Water Fittings) Regulations and Water Supply (Water Fittings) (Scotland) Byelaws. If the power cable or RCD are damaged in any way, the power must be disconnected until the part is replaced. Contact the retailer or manufacturer. The toilet must be fitted in a well-ventilated bathroom. The toilet must not be sprayed with liquid, or placed in a position it is likely to be sprayed. The toilet must not be installed in a location where it may be subject to high temperatures. The toilet must be stored in an upright position before installation. Do not over bend or kink the water supply hose as this could cause leaks Only use this product for its intended use. Only use attachments recommended by the manufacturer. Do not use this product in an outdoor environment. Children and people with limited physical, sensory or capabilities must be supervised when using this device or have been told the proper procedure for use beforehand. Do not climb or stand on the toilet. If the product is not working properly, disconnect from the mains and close the water supply valve immediately before contacting the supplier or a qualified professional. This is a Class I electrical appliance and must be correctly earthed. Make sure the earth cable is connected first during the electrical connection. In case of any damage to the supply cable, you must arrange for a certified and qualified electrician to replace the cable for you. This appliance is designed for fixed connection to the power supply. Connecting this appliance to the power supply must be performed by a qualified and authorised electrician. Incorrect repairs are dangerous. Repairs must only be carried out by trained and qualified engineers. 3 INSTALLATION DIAGRAMS - BeBa_24911 5 INSTALLATION DIAGRAMS - BeBa_26880 6 PARTS LIST Toilet Remote (Ba eries Not Included) Remote Control Holder Electrical Cable Coupler G3/8" ½" Flexi Hose Flow Limiter Stop Valve Filter x 2 Flush Pipe and Seal Waste Pipe and Seal Wall Fixing Rods Wall Fixing Nuts Wall Fixing Washers Side Fixing Bolt Sleeve 7 Wall Cushion TOOLS REQUIRED Tape Measure Pencil Phillips Screwdriver Flat Head Screwdriver Knife File Adjustable Wrench Wire Strippers 12mm Drill bit Hacksaw Drill PRODUCT OVERVIEW 8 BEFORE INSTALLATION Recommended installation area. IMPORTANT! Before commencing installation, the water and electrical supplies should be turned OFF. Please note with your floor mounted back to wall toilet, a Flush Pipe and Waste Pipe are supplied, these may not be required as it will be dependant on the cistern to which the toilet is being connected and the position of the soil stack. Before attempting installation, ensure that you are in possession of all the required tools and fittings to ensure successful installation. Prepare the wall with the wall frame fitted, tiled/finished with access holes prepared for the flush pipe and waste pipe. Prepare the water supply pipe with a 1/2" female connector and electrical 3 core cable (which should be connected to a 13-amp fuse spur or isolation switch outside the bathroom) as per below, allowing for 200mm of water supply pipe and 400mm of electrical cable to extend beyond the surface against which the toilet will sit, to allow connection to the toilet unit. Flush pipe from Wall Frame Waste pipe from Wall Frame 9 INSTALLATION INSTRUCTIONS Connect the stop valve to the pipe end, ensuring to fit an adequate seal and tighten using a spanner. Once connected and fully tightened, place a bucket under the stop valve, open the stop valve and flush the pipe for at least 10 seconds to remove any debris in the system. Once flushed through, turn the stop valve to the closed position. to fit the seal provided and tighten. Connect the 1/2" female threaded end of the Filter to the Stop Valve, ensuring Connect the 3/8"" - 1/2" Flexi Pipe to the Filter, ensuring to fit the seal provided and tighten using a spanner, do not over tighten as this could crack the plastic body of the Filter. The required water supply pressure is 0.7-7.5 Bar as stated in the instruction manual. Check the water supply when connecting the filter. To meet 0.7 bar water supply there should be 1.5L water (3 bottles water @ 500ml) within 60 seconds. Please note this is after the filter is installed. If this is not met, water flow must be increased. Push the flush pipe and waste pipe supplied into the wall frame, ensuring these are level and aligned. Using a ruler draw a line on the flush and waste pipe, where it meets the wall surface. 10 Remove the pipes from the wall and push them fully onto and into the back of the toilet pan, using a ruler mark a line level with the back of the pan. Remove the flush pipe and measure and measure the distance between the two marks, this will be dimension L1. From the end of the flush pipe measure dimension L1 and then add 6mm, cut at this point, as shown below. Carry out the same process for the waste pipe, but only add 3mm and cut at this point as shown below. Once cut, using a file, smooth off the pies internally and create a chamfer on the external edge as shown below. After cutting and filing, insert the pipes into the back of the toilet and ensure these are fully attached. 11 Remove the screws on the seat, using a cross head screwdriver, ensuring not to lose the screws once removed. Two people may be required for the next part of the installation. Pull the seat from the toilet pan (do not turn this upside down). The threaded bolts should be attached to the frame and screwed inwards until 48mm of thread is left exposed, as shown below. Place the toilet cushion against the wall over the threaded bolts and pipe holes 12 Push the toilet base into position against the wall, ensuring that the waste and flush pipes to the rear engage to create a full seal and the holes in the back of the pan sit over the threaded bolts on the frame. Pull through the flexi pipe and cable, to allow connection to be made with the seat unit. Push the threaded bolt sleeves over the threaded bolts and into the hole in the pan to prevent the metal of the bolt damaged the ceramic, during use. Place the washer onto the threaded bolt, then fit the nut and tighten until the pan is secure. 13 Slide out the support box from underneath the toilet pan, only when the pan is secured. Trim the cushion which is exposed around the edge of the toilet pan, using a sharp knife. Strip the end of the household cable to expose the wires for connection to the coupler. When stripped, tidy the ends and connect to the coupler as shown, ensuring the screws are tightened and the wire ends are fully secured. Carry out the same process for the cable attached to the toilet, then connect the coupler sections together. 14 Connect the end of the water supply flexi to the tank inlet on the underside of the toilet lid, this will require a firm push to connect the flexi to the inlet. Once fully inserted and secure, tighten the nut. Before replacing the seat, turn on the water supply, the stop valve and the electrical supply. After turning on the water and electrical supplies you MUST carry out the RCD test, instructions for this are printed on the rear of the RCD, also carry out a leak check on all water connections. If the water volume within the flushing system is too great and water splashes over the rim, a flush rate limiter is necessary. If after installing the limiter, the bowl does not fully empty/clean, cut off one or more teeth of the limiter When checks are completed and no leaks are found and RCD test is passed, the lid assembly can be re-fitted to the pan, feed the flexi pipe and cables carefully under the pan, so as not to trap the pipe or cable or cause any kinks, which will reduce water flow. Locate the seat onto the pan and push down at the rear (not in the middle), as this could crack the seat. When the seat is located, re-fit the seat screws and tighten until secure, then fit the cover caps. 15 INSTALLATION OF THE REMOTE HOLDER Clean the wall surface in the area in which the remotecontrol holder will be located Dry fully before attempting the installation From the rear of the holder, peel off the adhesive strip cover. Place the holder with the adhesive side to the wall, ensuring this is level, press to the wall firmly and hold for a couple of seconds. Once located and secure, place the remote control against the holder. The magnet within the holder will retain the remote in position. 16 On receipt of your remote, this should be synced to your toilet, if the remote does not work initially, check the batteries are installed and installed correctly and then try to sync the remote using the "Remote Sync" section The same applies when batteries are changed. OPERATION REAR WASH/ FRONT WASH While seated, press the rear wash or front wash button on the remote and the toilet will begin wash mode. Alternatively, the dial on the side of the toilet can be turned clockwise to activate front wash or anticlockwise to activate rear wash. The washing function will run for 3 minutes. Once your product is installed and all water and electrical supplies are csNouOnpTnpEeliec:steaad.rOeanncdcoenonpyeoecuratretpidornaoandldu, cyotopiuserriantotsiitolaenltlaeisld, ryaeonauddryatolfloilwer tauitsseerr.eaanddyefolercutrsicea. l NOTE: The toilet seat must have a water supply connected, the toilet Lift up the toilet seat lid, locate yourself so that the sensor detects a cuisseter.rn filling and the toilet flushing does not automatically confirm a water sPurepspslythisecwoansnhecbtuetdtotno,twhehesneayto. u do this the toilet will carry out initially NanOaTuEt:oImf tahteic tnooilzezt lies sneoltf-ucsleeadnfowrh7ic2hhloaustrs ftohreanreoxutnodp9ersaetcioonndwsillabned pthreoncetehdeewdabsyh a(fotarnukseclre)awni,llpcloemasmeernecfeer. to "Tank Self Clean Section" OWpheernatyioonu stop the wash, the toilet will self-clean for around 9 seconds. LWifht eunp tthhee wtoailseht smeoadt elidis, laocctaivteatyeodu, rasfetelfrsao1th0astetchoensdednesolarydtehteecntoszazlueser. will move for 18 seconds before staying in the set position for the rest of Pthreeswsatshhe. wash button, when you do this the toilet will carry out an aWuhtoilme aintiwc ansohzzmleosdeel,f-ycoleuacnawnhaidchjuslatstthsefoforllaorwouinngds9etstiencgosn: ds. The nozzle chamber flap will open, the nozzle will not immediately extend, but water will run from the chamber starting the cleaning process. The nozzle will then extend and water will continue to run (not spray), after approx. 9 seconds the wash (for user) will commence and start the spray. When you stop the wash, the toilet will self-clean for around 9 seconds. When the wash mode is activated, after a 10 second delay the nozzle will move for 18 seconds before staying in the set position for the rest of the wash. While in wash mode, you can adjust the following settings: 18 MASSAGE Change between "OSCILLATING", "PULSATING" AND "OSCILLATING AND PULSATING" functions. To access massage mode, keep pressing the + or temperature buttons. Then, press the + water flow button to change between the different massage functions. The Indicator lights on the remote will show the massage mode selected. 1 Light Oscillating Mode 2 Lights Pulsating Mode 3 Lights Oscillating and Pulsating Mode Please Note: The massage mode can only be adjusted using the remote control. WATER FLOW Change between LOW, MEDIUM or HIGH To adjust the water flow, press the + or water flow buttons on the remote. The indicator will show the rate that the water is flowing between LOW, MEDIUM and HIGH. You can also adjust the water flow using the dial located on the side of the toilet. Turn the dial clockwise to increase the flow or anticlockwise to decrease. 19 WATER TEMPERATURE ADJUSTMENT The water temperature can be adjusted. Use the temperature adjustment KPreesespanpdrheosldstihnegdiatlhoen tdheiaslidoe nof tohileet.sTihdee buttons on the remote. Press the + oTefmthpeerattuorielecat.n Tthhenebeteinmcrpeaeserad tbuyrtuerncinagn or to increase or decrease the temperature. tchloecknwibseeoirndcecrreeaasseed dbybtuyrnitnugrint ainntgiclockwise. cMloovcek"AwirisDery MoorddeeancdreInadiscaetodr Lbigyhtt"utorn"Ointhger iftunacntiotnics"loseccktiwoni,saes .these are not functions that you would change during the wash function. STOP Stops all functions immediately no matter where they are in their cycle. To stop any of the functions at any time, press the stop button on the remote control. ADJUST NOZZLE The nozzle position controls where the water is sprayed during washing mode. Change the nozzle position by using the + and nozzle buttons on the remote to retract or extend the nozzle. Please Note: The nozzle position can only be adjusted using the remote control. 20 Note: If the dial light flashes slowly (once every 2-3 seconds) during normal use, this doesn't indicate a fault. Please open the cover, do not sit on the seat, pull the knob and rotate it in the clockwise direction. The ambient light will be turned off. It will be turned back on when rotating it in the clockwise direction again.ction again. To turn this alert off, long press the temperature button "-" or "+" (do not release), at the same time short press the female wash button, and the LED light of the remote control is one grid, the beeping is off. If the LED light of the remote control is two grids, the beeping is on. Open the cover and seat, press and hold the knob to rotate, the sound will activate when turned clockwise(forward) and deactivate when turned anti-clockwise(backward). REMROemTEotCeOCNoTnRtrOoLl SSyYnNcCH Step 1 Open the lid and the seat. Turn o the night light using the side control (Refer to the "light Se ng") Step 2 Press and hold the STOP bu on (1) and "-" bu on (4) at the same me for a few seconds un rst light (5) ashes. Step 3 Release the STOP bu on (1) but keep pressing "-"bu on (4). Step 4 While s ll Pressing "-" bu on (4), press "-" bu on (2) then "+"bu on (3) then release the "-" bu on (4), the indicator lights will ash on and you will then know the ID code for the toilet by referring to the table below for future reference and the remote is then synced with the toilet. A few second later, all lights will turn o and you can start to control the toilet. For mu nstalla ons: When you nish the above 4 steps, you can press "-" bu on (2) and "+"bu on (3) to change the ID code for the toilet. There are 5 lights, but only t 4 lights indicate for the ID code as below: Not Illuminated Illuminated LIGHT SHOWING ID CODE NO 0 1 2 3 4 5 6 7 8 9 23 CLEANING AND MAINTENANCE Daily Remove water drops with a soft lint free cloth to avoid limescale build-up. Weekly Clean all surfaces and corners. Clean the spray nozzle is necessary (see Nozzle cleaning) Monthly Clean the ceramic with low acidic cleaning agents. Every 6 months Replace the filter if required. (see replacing the filter) NOTE: Do not use strong abrasive cleaning agents or materials, as this can damage the product and will invalidate your guarantee. TANK SELF-CLEAN If the product is not used for more than 72 hours, the next time it is used, and the wash function is activated, the unit will carry out a self-clean for approximately 3 minutes. All functions will be de-activated during this time. The nozzle will not extend but water will run out form inside the chamber into the toilet until the clean is completes CLEANING THE NOZZLE It is recommended that regular cleaning of the nozzle takes place to prevent blockages. To manually clean the nozzle, follow the below: Open the seat cover and seat, then rotate the control dial clockwise. The nozzle will extend, rub clean with a brush to clean the nozzle holes and then wipe clean. The nozzle will return after a 5-minute period or you can press the Stop button. 24 REPLACING THE FILTER The filter supplied has a life of 6 months and should be replaced to prevent reduced flow. This can be affected by the water type i.e. Hard Water areas. To replace the filter, you will need to turn off the power supply and the water supply and the seat will need to be removed. Once the power has been cut to the unit, unscrew the seat from the toilet, do not turn the seat upside down. Once removed, access the filter and the stop valve. Turn the stop valve to the closed position. Disconnect the filter and replace with the new part, ensuring to re-fit the seals. Feed the pipes back into the toilet base, turn the power back on and re-set the RCD Re-open the stop valve. Re-fit the seat and secure into position. 25 DRAINING THE WATER TANK The water and power must be cut to the unit before work is started Do not invert the seat. Ensure a water holding container is in place prior to draining Using pliers hold the plug on the tank turn the plug to OPEN and pull out Water will start to drain. After draining is completed, insert the plug and turn to CLOSE. 26 TROUBLESHOOTING Problem Potential cause The power supply may not be connected The water supply may be disconnected The filter may be blocked The washing function Seat detector not activated not operating Toilet lid is closed Function not used for more than 72 hours Seat assembly is not connected to water supply Seat not working and double beeping Hall sensor or infrared when lid up, seat down sensor failure and sensor covered The washing cycle is 3mins. The nozzle will stop spraying after Washing function 3mins, and then retract. suddenly stops and Water supply interrupted nozzle retracts. The seat detector has sensed the user left the seat The toilet lid is not fully open The water flow rate may be set at low grades The water supply pressure may Low water flow rate be too low The filter may be blocked Low water temperature The nozzle may be blocked The water temperature may be set at low grades The temperature of water supply is too low The nozzle comes out slowly The water flows out but the nozzle does not come out The dryer cannot work Low air temperature Night light is always off Night light is always on. Upon starting the washing function, the nozzle will be in self-cleaning mode before coming out. The toilet is not used for more than 72 hours The power supply may not be opened Not correctly seated The cover is closed The air temperature may be set at low grades The air heater is not working normally To much light in the surrounding environment. The night light function may be closed. 1. Environment is dark. Suggested action Ensure the power switch is in the on position and the RCD has been reset. Ensure the inlet water valve is in the open position, and ensure there is adequate water flow to the unit. Please replace a new filter. It has a service life of approx. 6 months. Ensure the seat is occupied to activate the function. Lift the toilet seat. The self-cleaning function will activate, which takes around 3 minutes. During self-cleaning all the buttons are deactivated until the function has completed. Check the seat assembly has a connected and flowing water supply, as the cistern filling does not confirm water to the seat. Replace seat assembly This is normal and please press the "wash" button to start another wash cycle. Please check if there is a water outage Please adjust sitting position Ensure the lid remains upright during the function. Please increase the flow rate as per "adjusting water flow rate" of operating instructions Please check and ensure the water supply pressure is 0.07Mpa Replace the filter. It has a service life of approx. half a year Please replace the nozzle Please set the water temperature at high grade as per "adjusting temperature "of the operating instructions Please set the water temperature at high grade as per "adjusting temperature "of operating instructions, or decrease the flow rate as per "adjusting water flow rate". This is normal This is normal. If not used for more than 72 hours, when the unit starts it will begin the self-cleaning for about 3 minutes Please turn on the power Please sit on the seat and adjust sitting position Please open the cover and sit on the seat Please set the air temperature at high grade as per "adjusting temperature "of operating instructions Please contact local distributor When the night light is set at smart mode, the night light will not work when in the bright environment. Please open the night light function and adjust the night light mode as per "Light Setting". When the night light is set to smart mode, the night light will be always on when in a dark environment 27 The nozzle goes back automatically when manual cleaning The remote control is not functioning There are BEEP sounds when the bidet is operating The bidet does not function normally The light around the control dial flashes twice with constant BEEP TThheelilgighht taraoruonudntdhethdeial ckoeenptrsoflladsihailnkge(eonpcse every fslaecsohnindgor less). 2. Something may be covering the control dial. 3. The night light may be set to `Always On' mode 1. The nozzle goes back after washing 5 minutes 2. Press the "stop" button 3. The seat detector senses that the seat is closing 1. There are no batteries in the remote control 2. Maybe the battery power is too low 3. Maybe the code of the bidet and remote control is not the same There is a short BEEP when you are sitting down, and a long BEEP when you leave. Also, there is a short BEEP when the bidet has received commands. Abnormal operation The water supply temperature may be too high There may be something wrong with the product Remove the obstructions around the control dial Please adjust the night light mode as per "Light Setting" of operating instructions This is normal Manual cleaning will be stopped if you press the control dial or press the "stop" button on the remote control. Please do not put down seat during manual cleaning Please install the correct batteries in the remote control When batteries are low, LED will flash. Change the batteries Please set the code of the remote control to the correct one. See "Remote Control Synch" This is normal. You can turn off the sound. See "Sound Setting" Please shut off the power and turn on after one minute. If the bidet still cannot work, please contact local distributor Please shut off the power and water supply, stop using the product, and then contact local distributor Please shut off the power and water supply, stop using the product, and then contact local distributor. If you should encounter an issue with operation/function of your product please contact BID Customer Service. To assist in the resolution, we will require your Serial number, a video of the issue, including operation of the remote or dial, position of the seat, video of the side control and sound to indicate any beeps which occur, this will give a full picture of the operation to help determine the best resolution or guidance. SUPPORT Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centers. At the time of printing the product contains no substances listed within Annex XIV of the Reach Regulations (EC) 1907/2006. In accordance with Article 59 of the same regulation the following substances are contained within the product at permitted levels: Lead & Cadmium. As a responsible manufacturer the regulations are monitored to ensure continued compliance. Further information can be provided upon request. 28 call 0330 390 3062 Write to Trident Business Park, Leeds Road, HD2 1UA TECHNICAL SPECIFICATIONS MODEL Wash Rear Wash Front Wash Oscillating Spray Pulsating Spray Oscillating and Pulsating Spray Adjustable Water Temperature Adjustable Flow Rate Adjustable Spray Position Warm Air Air Drying Adjustable Dryer Temperature Hygiene Nozzle Self Cleaning Nozzle Manually Cleaning Night Light Breathing Lamp Soft Closing Seat and Cover Body Control dial Remote Control Rimless Toilet Installation of the toilet Water Supply Connector Rated Voltage Power Length of Power Cord Water Supply Pressure Water Supply Temperature Ambient Temperature Protection Degree Flow Rate wash Device Water Temperature Wash Cycle Time Heating Mode Maximum Heater Power Safety Device Dry Device Backflow Prevention Maximum Speed Of Air Maximum Dryer Power Dry Cycle Time Warm Air Temperature Safety Device Remote Control Frequency Range Maximum RF Output Power Type of batteries Number of batteries Net Weight Dimensions 29 BeBa_24911/Beba_26880 5 Steps (Default 3rd) 5 Steps (Default 3rd) 5 Steps (Default 3rd) 5 Steps (Default 3rd) Wall Mounted G 3/8" ½" AC220240V, 50/60HZ 950W 1.8m 0.07~0.75MPa (0.7~7.5Bar) 4~35 C 4~40 C IPX4 350~650mL/min 31~39 C 3 Minutes Tank 1200W Thermal Cutoff/ Fuses\Liquid Level Switch\Thermostat Air Gap 5m/S 280W 3 Minutes 35~50 C Thermal Cutoff/ fuse>\Thermostat 2460MHz 10dBm 3V CR2032 Two pieces 32 Kg 593 x 370 x 380mm EU DECLARATION OF CONFORMITY Company Name: Postal Address: Postcode Telephone Number E-mail Address Buy It Direct Trident Business Park The Black Church Leeds Road St Mary's Place HD2 1UA Dublin 7 0871 620 1057 01 255 2070 Compliance@BuyitDirect.co.uk This declaration of conformity is issued under our sole responsibility and belongs to the following product: Type of product: Wall Mounted Intelligent toilet Model Number: BeBa_24911 / BeBa_26880 Brand: Better Bathrooms Object of Declaration BeBa_24911 and BeBa_26880 Wall Mounted Intelligent Toilets The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: Low Voltage Directive 2014/35/EU EMC Directive 2014/30/EU RoHS Directive 2011/65/EU Radio Equipment Directive 2014/53/EU Relevant harmonised standards used or other technical specifications in relation to which conformity is declared: SAFETY EN 60335-1:2012 +A13:2017 EN 62233:2008 EN 60335-2-84:2003 + A1:2008 EMC EN 61000-3-2:2014 EN 55014-1:2017 EN 61000-3-3:2013 EN 55014-2:2015 RED EN 301489 -1 V2.1.1:2017 EN 300440 V2.1.1:2017 EN 301489 -3 V2.1.1:2017 RoHS EU 2015/863 Authorised Signature Richard Leach Compliance and Quality Manager 24th August 2023 30 UK DECLARATION OF CONFORMITY Company Name: Postal Address: Postcode Telephone Number E-mail Address Buy It Direct Trident Business Park Leeds Road HD2 1UA 0871 620 1057 Compliance@BuyitDirect.co.uk This declaration of conformity is issued under our sole responsibility and belongs to the following product: Type of product: Wall Mounted Intelligent toilet Model Number: BeBa_24911 / BeBa_26880 Brand: Better Bathrooms Object of Declaration BeBa_24911 and BeBa_26880 Wall Mounted Intelligent Toilets The object of the declaration described above is in conformity with the relevant UK Statutory Instruments and Regulations: Electrical Equipment (Safety) Regulations 2016 Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 The Radio Equipment Regulations 2017 Relevant designated standards used or other technical specifications in relation to which conformity is declared: SAFETY EN 60335-1:2012 +A13:2017 EN 62233:2008 EN 60335-2-84:2003 + A1:2008 EMC EN 61000-3-2:2014 EN 55014-1:2017 EN 61000-3-3:2013 EN 55014-2:2015 RED EN 301489 -1 V2.1.1:2017 EN 300440 V2.1.1:2017 EN 301489 -3 V2.1.1:2017 RoHS EU 2015/863 Authorised Signature Richard Leach Compliance and Quality Manager 24th August 2023 31 DECLARATION OF PERFORMANCE DOP BB-34-24911/26880 UKCA Company Name: Postal Address: Postcode CE Company Name: Postal Address: Postcode E-mail Address Buy It Direct Trident Business Park, Leeds Road, HD2 1UA Buy It Direct The Black Church, St Mary's Place, Dublin 7 Compliance@BuyItDirect.co.uk This declaration of performance is issued under our sole responsibility and belongs to the following product: Type of product: Model Number: Brand: Object of Declaration Wall Mounted Intelligent toilet BeBa_24911/ BeBa_26880 Better Bathrooms BeBa_24911 and BeBa_26880 Wall Mounted Intelligent Toilet We hereby declare that the products named above have been designed, are produced and have been tested to comply with: Union Harmonisaon Legislaon and relevant harmonised standards Regulation (EU) No, 305/2011 Designated standards and relevant UK Statutory Instruments and Regulation Construction Products (Amendment etc.) (EU Exit) Regulations 2020 SI 2020/1359 BS EN997:2012+A1:2015 Personal Hygiene AVCP System 4 Essential Characteristics CL 1 -6A Class 1 product/ Flushing cistern WL Water Tightness / Leak Tightness BP Back Flow Prevention CA - Cleanability LR Load Resistance DA Durability Authorised Signature PASS PASS PASS PASS PASS PASS Craig Watson Technical Manager 9/9/22 32 33 236E400-E71-01K