X10DR Plus Programming Parameter Guide

Some features are only applicable to firmware version 4.0 Rev 1.3

How to Install Programmer

The X10DR programmer runs on PC or Mac running Windows 7/10. It requires a USB 2.1 Port. USB 3 ports may not be compatible; use a USB 2.1 patch block if necessary.

Included with the programmer download file are instructions for setting up the programmer on your Windows 7/10 PC. Follow these instructions for correct installation.

The X10DR User Programmer requires two separate programs to be installed:

Drivers: Install BlueSuite from www.x10dr.com. When selecting components, choose 'Blue Core'. Do not install 'Core', 'BlueTest3', or 'DFU' tools.

How to Use Programmer

To put Handset into programming mode: Turn off the handset, attach the programming cable between the device hirose port and the PC. Press and hold the red handset on/off button while holding PTT. The LED will light red.

To put Gateway into programming mode: Turn off the gateway. Hold the gateway ON/OFF button down while attaching the programming cable to the device micro-USB port and PC USB port. The LED will light red. Note: The gateway's RJ45 socket should not be connected to the host radio.

Important: Always READ the device first before proceeding. It is recommended to SAVE the file onto your PC for re-loading if required. A greyed-out feature indicates the device does not support that capability.

Programmer Functions:

Read Device: Load current programming parameters from the device to the screen.
Program Device: Load current screen programming parameters to a device.
Restart (important): Restart the programmed device before removing the programming cable.
Lock - Unlock File: Lock your desired parameter configuration before undertaking batch fleet programming to prevent accidental changes.
Save File: Save programming parameters from the screen to a desired PC location.
Defaults: Reset to default device parameters.
Load File: Load previously saved programming parameters to the device from its PC location.
Exit: Exit the program.

Handset Parameters

The X10DR system offers various programmable parameters for the handset:

Basic Functions:

Radio PTT key beep: Sounds talk permit tone sequence when PTT is pressed and handset is in range. Default: OFF
Emergency key beep: Sounds single tone when Emergency button is pressed and handset is in range. Default: ON
Talkaround PTT key beep: Sounds talkaround tone sequence when Talkaround button is pressed and handset is in range. Default: ON
Stealth mode always active: Disables all alert tones and LED status light. Default: OFF
Mute speaker on PTT: Disables all speaker audio when PTT is pressed. Default: OFF
Mute speaker on charge: Disables speaker when handset is in gateway or charger. Default: ON
LED charge indicate: Disables the “momentary blink” charge indicator. Default: ON
Auto turn on when charging: Handset automatically turns on when placed in gateway or charger. Default: ON
Minimum volume is off: Allows user to turn speaker audio off instead of level 1. Default: OFF
Mandown Biometeric Monitor (when fitted): Enables/disables function for Plus handsets with XMD option. Default: OFF
Internal Mic Only Operation: Maintains operation via internal microphone when accessory is attached to Hirose port. Default: OFF
Out of range turn off time: Sets time in hours before handset powers off if not connected to a gateway. Default: 8 hours
Low battery beep voltage: Sets the battery voltage at which low battery alert tones are generated. Default: 3.5V
Low battery beep interval timer: Sets the interval for low battery alert tones. Default: 5 minutes

Elite Plus Only Options:

Handsfree Function: Enables user-selectable handsfree function. Default: ON
Toggle PTT/TA Button Assignment: Configures the top grey Control button to toggle the side PTT button assignment between host radio PTT and Talkaround or 2nd Radio device PTT/PA Mode. Default: OFF
Command Relay Mode / Automatic Relay Mode: Selects the Relay Mode type. Default: Command Relay

Handset Audio Levels

The following handset adjustments cater for different audio accessories and user applications:

Internal Mic Gain: Sets internal microphone transmit audio sensitivity. Default: 3
Internal Mic High Gain Boost: Sets internal microphone sensitivity when “Live Mic” is active. Default: 6
External Mic Gain: Sets external microphone transmit audio sensitivity. Default: 9
External Mic High Gain Boost: Sets external microphone sensitivity when “Live Mic” is active or high gain is manually selected. Default: 6
Remote PTT Gain Boost: Increases internal microphone sensitivity when remote/handlebar PTT is pressed. Default: 9
Fixed Alert Tone Volume: Limits all monitored alert tones to a set level, overriding handset volume controls. Default: OFF
Alert Tone Volume: Sets the “Fixed Alert Tone” volume. Default: 5

Note: Use the Gateway Audio Level Adjustment - XGALA software tool (downloadable at www.x10dr.com) for setting audio in and out of the gateway to the host mobile radio.

Handset Emergency Features

Parameters for emergency functions:

Audio link active time: Duration transmit audio is active after Emergency button is released (for “Live Mic” function). Default: 0
Transmit Time: Duration X10DR “Live Mic” handset Tx audio is active when Advanced Emergency is activated. Default: 0
Receive Time: Duration X10DR “Live Mic” handset Rx audio is active when Advanced Emergency is activated. Default: 0
Emergency repeat cycles: Number of “Live Mic”, Tx and Rx cycles when Advanced Emergency is triggered. Default: 1
Transmit audible emergency tone: Transmits an audible emergency warble tone over the host mobile radio channel. Default: Off

Handset Hardware Parameters

Configure hardware functions for the handset:

Hirose Pin 2 function: Sets Hirose pin 2 to BAT+ (~3.8VDC) for powering accessories or bridged output speaker audio. Default: Speaker -VE
Acc PTT: Sets whether Hirose PTT input generates Talkaround or Radio PTT. Default: Radio PTT
PTT: Sets the function of the main PTT button. Default: Radio PTT
Top 1: Sets the function of the top left button. Default: Emergency
Top 2: Sets the function of the top right button. Default: Talkaround PTT
Left 1: Sets the function of the bottom left button. Default: short press Volume up / Elite Plus only - long press Relay mode off/on
Left 2: Sets the function of the bottom left button. Default: short press Volume down
Right 1: Sets the function of the right side button. Default: short press Search / long press Power off/on
Long Press Duration: Sets the time a button must be pressed to detect a Long Press. Default: 500mSec

Gateway Parameters

Configure various parameters for the X10DR gateway:

Audio Levels - Gateway:

Receiver Input Gain From Radio: Sets receive input sensitivity. Default: 0
Transmit Output Gain To Radio: Sets audio output level to radio when local/remote/handlebar PTT is pressed or “Live Mic” is active. Default: 0
Talk Around Output Gain to other X10DRs: Sets the “intercom” audio level. Default: 0
Find Me™ Function: Enables Find Me function in gateway. Default: OFF
Radio Receive VOX/COR: Enables VOX derived COR. Default: ON
VOX Trigger Level: Sets gateway audio detect sensitivity for VOX derived COR. Default: 70
Public Address Mode: Sends only handset Talkaround audio to the gateway 3.5mm jack. Default: OFF
Monitor Emergency Input Alert Tone: Causes Emergency warble alert tone to sound in all cross connected X10DR handsets. Default: OFF

Trunking Support:

Enables speaker audio upon PTT for 500mS to allow clear distinction of host trunked mobile's Channel Grant/Talk Permit tones. Handset Mic audio is muted for 500mS to prevent rebroadcast. For optimum performance, set VOX trigger level for 90-100. Default: OFF

Elite Series Only Options:

Multi Operational Mics: Allows two or three Elite Series Mics to be simultaneously operational through one Elite gateway unit. Default: ON
Remote Find Me™: Enables Find Me function in gateway via grounding the white wire connected to pin 8. Default: OFF

For ease of setting, use the XGALA Gateway Audio Level Adjustment software tool (downloadable at www.x10dr.com/support).

Gateway Hardware Parameters

Configure hardware interface pins for the gateway:

I/O: Defines whether a gateway interface pin is an input or an output.
Active: Sets whether the interface pin needs to be held low or pulled up high to activate functionality.
Function: Assigns desired functionality to the interface pin from dropdown boxes.
Pulse: Defines the length of time an input must be activated before the function is triggered, or how long an output is activated. A value of zero means an input triggers instantly.

Pro Plus Default Settings

Refer to the diagrams for Pro Plus default settings for Handset and Gateway configurations.

	X10DR Programming Parameter Guide for Elite Plus and Pro Plus Models Comprehensive guide to programming X10DR Elite Plus and Pro Plus mobile radio communication solutions, covering installation, usage, handset, and gateway parameters, with default settings and configuration options.
	Wireless Pacific X10DR Elite Plus: Secure Wireless Microphone System for First Responders Explore the Wireless Pacific X10DR Elite Plus, a robust and secure wireless microphone system designed for public safety and emergency services, offering enhanced communication range, AES encryption, and critical safety features.
	X10DR Talk Back Microphone: User Guide and Setup Instructions Comprehensive user guide for the X10DR Talk Back Microphone (XTBM). Learn about its parts, functions, initial setup, microphone and radio level adjustments, and control button re-assignment options for optimal communication.
	X10DR XRD-U1L UHF Radio User Card \| Wireless Pacific User card and operational guide for the Wireless Pacific X10DR XRD-U1L UHF Radio Speaker Mic, detailing features, how to operate, and compatibility with Peltor Lite-Com headsets.