STANLEY Portable Power Station Instruction Manual

Introduction

Congratulations on purchasing your new STANLEY Portable Power Station. This manual provides essential information for safe and effective operation. Please read and follow all instructions carefully before using this unit.

Product Overview

The STANLEY Portable Power Station (Model J5CPD) is a versatile device designed for multiple functions, including jump-starting vehicles, providing AC power, charging USB devices, and powering an air compressor. It features a built-in 12V DC sealed lead-acid battery, a digital LCD screen, and various control buttons.

Features

• 1. Rubber Grip Handle
• 2. Pivoting LED Area Light
• 3. AC Power Button
• 4. Backlit LCD Screen
• 5. USB Ports (3 total)
• 6. Three-Prong 120 Volt AC Outlet
• 7. Decrease Compressor Pressure Control Button (➖)
• 8. Compressor Power Button
• 9. Increase Compressor Pressure Control Button (➕)
• 10. Jump Starter Power Button
• 11. Area Light Power Button
• 12. USB Power Button
• 13. Built-in 120 Volt AC Charger (under protective cover)
• 14. Negative (➖) Black Clamp
• 15. Positive (➕) Red Clamp
• 16. Air Hose and Sure Fit® Nozzle
• 17. Nozzle and Air Hose Storage
• 18. Nozzle Adapter

Safety Guidelines and Instructions

⚠️ DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

⚠️ WARNING: Indicates a potentially hazardous situation which, if not avoided, may result in death or serious injury.

⚠️ CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

General Safety Warnings:

• This unit is designed for household use only.
• Avoid dangerous environments (damp, wet, rain).
• Keep children and visitors away from the work area.
• Dress properly; avoid loose clothing or jewelry.
• Store idle appliances indoors in a dry, high, or locked-up place.
• Do not abuse the power cord; keep it from heat, oil, and sharp edges.
• Disconnect the appliance from the power supply when not in use, before servicing, and when changing accessories.
• Ground Fault Circuit Interrupter (GFCI) protection is recommended.
• Use only manufacturer-recommended accessories and attachments.
• Stay alert and use common sense; do not operate when tired or impaired.
• Check for damaged parts; replace any damaged parts before further use.
• Do not operate near flammable liquids or in gaseous or explosive atmospheres.
• Never submerge this unit in water; do not expose it to rain or snow.
• To reduce the risk of electric shock, disconnect the unit from any power source before maintenance or cleaning.
• In garages or enclosed areas, the unit MUST be placed not less than 18 inches (457 mm) above the floor due to sparking parts.
• Do not insert foreign objects into the USB ports or the 120V AC outlet.

Specific Safety Instructions for Charging This Unit:

• The unit is delivered partially charged; fully charge for at least 40 hours before first use.
• You cannot overcharge the unit using the AC charging method.
• Use only the built-in AC charger.
• Turn off all functions when the unit is charging or not in use.

Extension Cords:

⚠️ WARNING: Use of an improper extension cord can result in fire and electric shock. Ensure the extension cord has the same pin configuration, is heavy enough for the current draw, and is in good electrical condition. Refer to the table below for minimum gauge requirements based on cord length and voltage.

⚠️ CAUTION: Pull extension cords by the plug, not the cord, when disconnecting.

Specific Safety Instructions for Jump Starters:

⚠️ WARNING: Use only for lead-acid batteries; do not use for dry-cell batteries. Risk of explosive gases; work in a well-ventilated area. Never jump-start a frozen battery. Keep away from moving parts, sparks, and flames. Never touch clamps together. Ensure correct polarity connection; reverse polarity will trigger an alarm. Disconnect negative cable first. Do not expose battery to fire or extreme heat.

⚠️ CAUTION: Vehicles with computerized systems may be damaged; consult the vehicle manual. Excessive cranking can damage the starter motor. Do not use on watercraft. Keep unit upright.

Specific Safety Instructions for Inverters:

⚠️ WARNING: Do not connect to AC distribution wiring. Not for ignition-protected areas. Do not immerse in water. Do not insert foreign objects. Do not operate near flammable materials. Do not expose to extreme heat.

⚠️ CAUTION: Disconnect appliance before repair. Use outdoor-rated extension cords for outdoor use. Do not operate while driving. Ensure adequate ventilation. Turn off when not in use. Not suitable for high-wattage, heat-producing appliances (hair dryers, microwaves), medical devices, or some laptops.

Specific Safety Instructions for USB Ports:

• Do not insert foreign objects.
• Do not attach USB hubs or more than one device per port.
• Do not exceed 3.1A (5V) per port.
• Some household USB electronics may not operate with this unit.

Specific Safety Instructions for Compressors:

⚠️ CAUTION: Never leave unattended. Do not operate continuously for more than 10 minutes to prevent overheating. Allow 30 minutes cooling time if needed for longer operation.

⚠️ WARNING: Burst hazard; follow inflation instructions carefully. Never exceed recommended pressure. Monitor pressure at all times.

Personal Safety:

• Have immediate assistance available when working with batteries.
• Remove metal jewelry.
• Do not wear vinyl clothing.
• Wear protective eyewear.
• Have fresh water and soap nearby for battery acid contact.
• First Aid:
  • Skin: Rinse immediately with water, then wash with soap and water. Seek medical attention if irritation occurs.
  • Eyes: Flush immediately with water for at least 15 minutes. Seek medical attention.
  • LCD Liquid Crystal: Wash skin with water, remove contaminated clothing. Flush eyes with clean water. If swallowed, rinse mouth, drink water, induce vomiting, seek medical attention.

Operating Instructions

Viewing Battery Status:

The backlit LCD screen displays the battery charge level via the Battery Status Icon (four solid bars for full, one for nearly empty, four blank for completely empty) and the Battery Voltage Indicator.

Charging/Recharging:

Initial Charge: Fully charge for 40 hours or until the Battery Status Icon shows 4 solid bars before first use.

Routine Charging: Recharge at least every 30 days and after each use to maintain battery health.

⚠️ CAUTION: Failure to keep the battery charged can cause permanent damage.

To Charge/Recharge using Built-in 120V AC Charger:

1. Lift the protective cover of the built-in AC charger.
2. Connect an extension cord (not included) to the unit and plug into a standard 120V AC wall outlet.
3. The LCD screen will display charging status. The Battery Status Icon bars will fill from bottom to top.
4. Charge for approximately 40 hours or until 4 solid bars are shown.
5. Unplug the extension cord from the outlet and then from the unit.

Jump Starter:

⚠️ WARNING: Follow all jump starter safety instructions. Never touch clamps together. Ensure correct polarity.

Procedure:

1. Turn off vehicle ignition and all accessories. Put vehicle in "park" and set the emergency brake.
2. Ensure the Jump-Starter Power Button is OFF.
3. Remove clamps from tabs. Connect the red clamp first, then the black clamp.
4. For Negative-Grounded Systems (most common): Connect the positive (➕) red clamp to the vehicle battery's positive terminal. Connect the negative (➖) black clamp to the vehicle chassis or a solid, non-moving metal part away from the battery (e.g., engine block).
5. For Positive-Grounded Systems: Connect the negative (➖) black clamp to the vehicle battery's negative terminal. Connect the positive (➕) red clamp to the vehicle chassis or a solid, non-moving metal part away from the battery.
6. When clamps are connected properly, the LCD screen will display Battery Status, Voltage, Clamp Icons, and +/- signs.
7. Turn the Jump-Starter Power Button ON. The Jump Starter Icon (⚡) will flash, indicating readiness.
8. Crank the engine in 5-6 second bursts until it starts.
9. Turn the Jump-Starter Power Button OFF.
10. Disconnect the negative (➖) clamp first, then the positive (➕) clamp (except for positive-grounded systems).

Display Indications: The LCD screen shows specific icons and messages for correct connection, reverse polarity (❌ alarm sounds, icons flash), clamps touching (⚡ intermittent alarm), and overheating (? alarm sounds, jump starter icon flashes).

IMPORTANT: Always turn the unit off when not in use. Recharge fully after each use.

Area Light:

1. Press the Area Light Power Button to turn the light ON.
2. Press again to turn it OFF.
3. The LCD screen will display Battery Status and Voltage when the light is on.

120 Volt AC Power Outlet:

This outlet provides up to 500W continuous power. It uses a modified sine wave output, suitable for most AC loads.

Protective Features: The inverter monitors and will shut down automatically for low/high battery voltage, overheating, or overload/short circuit conditions.

Using the 120V AC Outlet:

1. Press the AC Power Button to turn the outlet ON. The LCD will display "AC".
2. Insert the 120V AC plug of your appliance into the outlet.
3. Switch on the appliance.
4. Press the AC Power Button again to turn the outlet OFF.

Fault Conditions: If a fault occurs (low/high voltage, thermal, overload), the AC outlet will shut down automatically. The LCD will display fault indicators. Follow on-screen prompts and troubleshooting steps.

USB Ports:

The unit has three USB ports, each providing 3.1A (5V) for charging devices. They do not support data communication.

Using the USB Ports:

1. Press the USB Power Button to turn the ports ON. The LCD will display Battery Status, Voltage, and the USB Icon (?).
2. Plug your USB-powered device into a port.
3. Press the USB Power Button again to turn the ports OFF.

IMPORTANT NOTES: Do not exceed 3.1A per port. Some USB electronics may not operate correctly. Monitor for fault conditions (low battery, overload, short circuit) indicated on the LCD.

Portable Compressor:

The built-in 12V DC compressor can inflate tires and inflatables up to 120 PSI.

⚠️ CAUTION: Do not operate continuously for more than 10 minutes to prevent overheating. Allow 30 minutes cooling time if needed.

Inflating Tires or Products With Valve Stems:

1. Screw the Sure Fit® nozzle onto the valve stem.
2. Press the Compressor Power Button. The LCD will display current and set pressure.
3. Use the ➕ and ➖ buttons to set the desired pressure (1-120 PSI).
4. Press the Compressor Power Button again to begin inflating. The Compressor Icon (?) will flash.
5. The compressor stops automatically when the set pressure is reached.
6. Press the Compressor Power Button to turn OFF the unit.
7. Unscrew the nozzle and allow the unit to cool before storing.

Inflating Other Inflatables Without Valve Stems: Use the nozzle adapter and follow steps similar to inflating tires.

Care and Maintenance

• Recharge the battery at least every 30 days when not in use.
• Clean the exterior with a soft, damp cloth. Never submerge the unit in water.
• Periodically inspect adapters, connectors, and wires. Contact the manufacturer for replacements.

Battery:

The battery is designed for the service life of the unit and is not user-replaceable.

Safe Battery Disposal:

Contains a sealed lead-acid battery. Recycling is required. ♻️ Do not dispose of in fire or extreme heat. Protect terminals with tape before disposal.

Troubleshooting

• Unit will not charge: Ensure AC Power Button is OFF. Check extension cord connection.
• Unit fails to jump-start: Ensure not in Compressor mode. Ensure Jump-Starter Power Button is ON. Check polarity. Allow unit to cool if overheated. Recharge if necessary.
• 120V AC outlet will not power appliance: Ensure AC Power Button is ON. Check appliance wattage (max 500W). Check appliance cord/plug. Recharge if necessary.
• USB power port will not power appliance: Ensure USB Power Button is ON. Check for Fault Icon on LCD. Ensure total draw does not exceed 3.1A (5V). Some electronics may not be compatible. Recharge if necessary.
• LED area light does not come on: Ensure Area Light Power Button is ON. Recharge if necessary.
• Portable compressor will not inflate: Ensure not in Jump Starter mode. Ensure Compressor Power Button is ON. Check Sure Fit® nozzle connection. Allow compressor to cool if overheated. Recharge if necessary.

Specifications

• Boost Ampere: 12V DC, 1200A peak battery, 600A instantaneous
• Battery Type: Maintenance-free, sealed lead-acid, 12V DC
• AC Input: 120V AC, 60Hz, 13W
• Area Light: 1 white LED
• USB Ports: 3.1A max., 5V DC
• AC Outlet: 120V AC, 60Hz, 500W continuous
• Compressor Maximum Pressure: 120 PSI

Warranty Information

The manufacturer warrants this product against defects in materials and workmanship for ONE (1) YEAR from the date of retail purchase by the original end-user purchaser. If a defect is found within the warranty period, the product may be replaced or repaired at the manufacturer's option. Proof of purchase may be required. This warranty does not apply to accessories, bulbs, fuses, batteries, or defects from normal wear and tear, accidents, misuse, or unauthorized repair. This product is not intended for commercial use.

Register your product at https://www.baccusglobal.com/registration for important product information and offers.

Service Information

For technical advice, repair, or genuine factory replacement parts, contact the manufacturer at 1-877-571-2391.