Connects2
Instruction Manual for Connects2 models including: CAM-42, Vision Wide Angle Universal Brake Light Camera
Read the manual prior to installation. Technical knowledge is necessary for installation. Please ensure you use the correct tools to avoid damage to the ...
22 мая 2021 г. —
File Info : application/pdf, 4 Pages, 15.49MB
DocumentDocumentV1-10-19 Connects2Vision User Manual CAM-42 Wide Angle Universal Brake Light Camera 2-in-1 Reversing Camera/Brake Light Solution with Wireless Controller PRODUCT FEATURES: - Resolution - Picture Mode - CMOS Chipset: - Lens FOV: - Viewing Angles: - Waterproof Rating: - Parking Guidelines 720 x 480 (Wide Angle View) NTSC 1/3" 210 Degrees (H) x 140 Degrees (V) Birds-Eye, Wide Angle, Reversing Left/Right Blind Spot, Driving IP67 Yes (Removable/Dynamic) Prior to Installation Read the manual prior to installation. Technical knowledge is necessary for installation. Please ensure you use the correct tools to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product. Technical Support Connects2 want to provide a fast and suitable resolution should you encounter any technical issues. With this in mind, when contacting Connects2, try to provide as much Information as possible. This will speed up the process and help us to help you. Please use our dedicated online technical support centre: support.connects2.com INSTALLATION Wiring Diagram Connects2Vision CAM-42 Make Connections to Vehicle/Unit or Screen Power Adapter Cable Wireless Controller (Mount on dashboard) 5 Extension Cable 4 3 2 Control Unit 1 1 Red Acc 12V 2 Black Ground 3 Purple Reverse 4 Blue CAN + White CAN - Connect to vehicle 12V Accessory feed Connect to ground Connect to reverse light Connect to rear of OBD connector (see diagram on Page 3) Connect to rear of OBD connector (see diagram on Page 3) 5 Green Reverse Trigger OUTPUT Vehicle Connection Overview Connecting CAN-Bus Wiring Control Unit Connect the CAN + (blue) and CAN - (white) wires to the OBD plug or other position. Fiat Ducato Peugeot Boxer Citroen Relay Extension Cable 2 8 76 5 4 3 21 16 15 14 13 12 11 10 9 FRONT OF OBD CONNECTOR OBD position can be found on the pin 1 & 9. Connect to the wire side of the plug IMPORTANT: Other vehicles CAN positions may vary. Power Adapter Cable www.connects2.com USING THE WIRELESS CONTROLLER Connects2Vision Start-Up The wireless controller included in the kit can be used to change the viewing mode of the camera, as well as adjust key parameters for each viewing mode. To bring up the HUD menu, put the vehicle into reverse gear and press A on Remote Control. Remote Control A Go to Settings HUD Display Screen A Go to Settings B Adjust Parameter C B Adjust Switch to Parameter Wide Angle Currently Selected View C Switch to Birds-eye Note: The HUD menu will time-out after 3 seconds to allow an uninhibited view of the camera image. Press the A button on Remote Control to bring the HUD menu back onto the screen. The currently selected viewing mode is displayed by the icon in the centre of the HUD menu. This will default to Driving/Rear-View mode, or to Reversing mode when in reverse gear. To change the camera mode, whilst the vehicle is in reverse gear, press B or C on Remote Control to cycle through the Reversing, Wide Angle and Birds-Eye viewing Modes. Viewing Modes Reversing (Select from HUD Menu) Driving/Rear-View (Default view when not in reverse) Wide Angle (Select from HUD Menu) Right Blind Spot (Triggered by Indicator - See Page 4) www.connects2.com 3 Connects2Vision Birds-Eye (Select from HUD Menu) Left Blind Spot (Triggered by Indicator - See Page 4) Adjusting Settings To adjust settings for all viewing modes, press A on Remote Control to enter the settings menu. Once in the settings menu, short press A on Remote Control to cycle through the various settings screens available. Screens include camera angle and position for each mode, and guideline width for parking lines. Once in a settings screen, the selected setting is indicated by the icon in the centre of the display. The parameters can be adjusted with B and C buttons on Remote Control. To return to the previous screen, Press and hold A on Remote Control. Remote Control Move to next A setting (Short Press) Return to previous (Long Press) HUD Display Screen B Adjust paramater (Short Press) Activate/ Deactivate BSV (Long Press) C B Adjust Adjust paramater Parameter (Short Press) Activate/ Deactivate BSV (Long Press) A Move to next setting (Short Press) Return to previous (Long Press) Currently Selected Setting C Adjust Parameter Activating/Deactivating Blind Spot View (BSV) Mode When in any of the settings screens, a long press of B on Remote Control will activate or deactivate BSV (Blind Spot View). When active, this will trigger the blind spot camera image when an indicator is activated and the vehicle is moving at a speed of over 40km/h. When inactive, using the indicators will not trigger the blind spot view and the camera will remain in Driving/Rear-View mode. Note: this function will only work if the CAN-Bus wiring is connected. 4 www.connects2.com