Centerline | Centerline Food Equipment
Centerline | Centerline Food Equipment
User Guide for centerline models including: CF48683, CDH and CDL Door Type Dishwasher, CF48683 CDH and CDL Door Type Dishwasher, CDL Door Type Dishwasher, Door Type Dishwasher, Type Dishwasher, Dishwasher
Centerline by Hobart CDH-1 High Temperature Door-Type Dish Machine
File Info : application/pdf, 5 Pages, 2.32MB
DocumentDocumentINSTRUCTIONAL VIDEOS VIDEOS INSTRUCTIVOS VIDÉOS INSTRUCTIVES CDH & CDL DOOR TYPE DISHWASHER | Daily Operation & Cleaning Guide Assemble Armar Assembler Click! x2 Click! Startup Puesta en marcha Lo Mise en marche Cycle Ciclo Cycle EXTENDED CYCLE CICLO EXTENDIDO CYCLE PROLONGÉ x2 Shut Down Apagar Fermeture CDL Unit CHEMICAL LEVELS NIVELES QUÍMICOS NIVEAUX CHIMIQUES Clean Up Limpiar Nettoyer Operation Tips | Consejos de operación | Conseils d'utilisation PRE-SCRAP DISHES PLATOS PREVACIADOS TREMPER LA VAISSELLE DO NOT OVERLOAD RACKS NO SOBRECARGUE LOS CESTOS NE PAS SURCHARGER PAS LES PANIERS CHECK CHEMICALS COMPRUEBE LOS PRODUCTOS QUÍMICOS VÉRIFIER LES PRODUITS CHIMIQUES USE COMMERCIAL CHEMICALS ONLY USE SOLO PRODUCTOS QUÍMICOS COMERCIALES UTILISER UNIQUEMENT DES PRODUITS CHIMIQUES COMMERCIAUX DELIME MACHINE AS NEEDED DESCALCIFIQUE LA MÁQUINA COMO SEA NECESARIO DÉTARTRER LA MACHINE AU BESOIN ©2022 Hobart 701 S. Ridge Avenue, Troy, OH 45373 | Phone: (888) 378-1338 | centerlinefoodequipment.com | Resource Center: CenterlineFoodEquipment.com/CenterlineDoorTraining F48683 (01/22) CDH/CDL SCAN TO WATCH MENU PROGRAMMING VIDEO CUH/CUL PROGRAM SETTINGS Access Changing Parameters 1. Press Menu Button 2. EXIT MENU OPEN door and close 00 = Extended Wash 3-6 minute limit Change Setpoint by Increase Decrease EXIT MENU OPEN DOOR 01 = Cycle Count Counter reading has 6 digits (012345 cycle) EXIT MENU OPEN DOOR For CUH, CUL, CDL & CDH Models equipped with internal chemical pumps 02 = Detergent Dispensing 0.0-20.0g/l Change Setpoint by Increase Decrease EXIT MENU OPEN DOOR 03 = Prime Detergent Pump Repeat as needed to prime the line Flashing (Dot) Pump On EXIT MENU OPEN DOOR 04 = Rinse Aid Dispensing 0.0-2.0g/l Change Setpoint by Increase Decrease EXIT MENU OPEN DOOR 05 = Prime Rinse Aid Pump Repeat as needed to prime the line Flashing (Dot) Pump On EXIT MENU OPEN DOOR For CUL & CDL Models Only 06 = Sanitizer Dispensing Range can be 0-100% Change Setpoint by Increase Decrease EXIT MENU OPEN DOOR 07 = Prime Sanitizer Pump Repeat as needed to prime the line Flashing (Dot) Pump On EXIT MENU OPEN DOOR 08 = Temperature Label (°F/°C) Change Setpoint by Increase Decrease 09 = Chemical Pump Control For CDH Model Only Change Setpoint by Increase Decrease EXIT MENU OPEN DOOR EXIT MENU OPEN DOOR Setting 0 1 2 Chemical Pump Control Configuration Internal chemical dosing pumps and external chemical signals disabled Control of internal chemical dosing pumps enabled Control signals for external chemical supply enabled 13 = Software Version / Machine Program i.e. Version 3.5 Press and Hold for Machine or Program i.e. Program 4 EXIT MENU OPEN DOOR © 2021 Hobart 701 S. Ridge Avenue, Troy, OH 45373 | Phone: (937) 332-3000 | centerlinefoodequipment.com F48658 (10-21) CDH/CDL SCAN TO VISIT THE CENTERLINETM RESOURCE CENTER OPERATION and ERROR CARD 2 3 5 4 1 CUH/CUL 6 7 1. POWER/DRAIN BUTTON Pressing this button switches the machine on, fills and heats the wash tank. Pressing and holding (3 seconds) activates selfcleaning cycle, drains machine, and then switches the machine off automatically. After machine is switched off, however, the machine still has voltage. 2. START BUTTON CUH & CUL Pressing this button starts the wash cycle. If pressed a 2nd time within 10 seconds of the first press, the extended wash cycle is activated. CDH & CDL After closing the door to start the wash cycle, pressing this button within 10 seconds of the cycle starting activates the extended wash cycle. 3. MENU BUTTON* Pressing this button enters the configuration menu. *For more detail review Operation and Install manual 4. DELIME BUTTON* Pressing and holding (3 seconds) activates the deliming cycle. 5. TEMPERATURE DISPLAY, WASH TANK Displays wash tank temperature while machine is in ready state or in a wash cycle. 6. TEMPERATURE DISPLAY, RINSE Displays rinse temperature only when rinse is active. 7. TEMPERATURE UNITS LED lights for °F or °C. WASH PROGRAM CUH & CUL Normal wash for average soiled dishes 2 minutes Extended wash for heavy soiled dishes 3 to 6 minutes* CDH & CDL Normal wash for average soiled dishes 1 minute Extended wash for heavy soiled dishes 3 to 6 minutes* ERROR CODE SYMPTOM 01 Booster Temperature Temperature above upper limit 02 Booster Temperature Temperature below lower limit POSSIBLE SOLUTION* 1. Press the power button to power off (Provide 20 min to cool off). 2. Restart as normal. 3. If error continues to display, possible high limit trip or heating element malfunction contact Hobart Service. 1. Press the power button to power off. 2. Restart as normal. 3. If error continues to display, possible high limit trip or heating element malfunction contact Hobart Service. ERROR CODE SYMPTOM Rinse Assurance 03 Booster did not meet temperature or water level requirements 05 Wash Tank Temperature Temperature above upper limit 06 Wash Tank Temperature Temperature below lower limit 07 Booster Pressure Level Sensor Voltage above upper limit 08 Booster Pressure Level Sensor Voltage below lower limit 09 Wash Tank Pressure Level Sensor Voltage above upper limit 10 Wash Tank Pressure Level Sensor Voltage below lower limit 12 Drain Overflow Limit Wash tank water level exceeded limit 13 Wash Tank Fill Time Exceeded 14 Drain Error Shutdown Machine took too long to drain 18 Fill Error Booster Booster took too long to fill 19 Chemical Deficiency Detergent / Rinse Aid / Sanitizer do Program Interrupted or Fill, wash, or delime cycle 22 Low Rinse Temperature 24 USB Drive Not Detected 25 Communication Error FIL Low Water Level at Start of Wash Cycle 30 Booster Heat Up Time Exceeded at Startup 31 Fill Error POSSIBLE SOLUTION* 1. When booster does not reach temperature or water level set point, a long wash cycle of 10 to 20 minutes will trigger. 2. If error continues to display on next cycle, possible high limit trip or heating element malfunction contact Hobart Service. 1. Press the power button to power off (Provide 20 min to cool off). 2. Restart as normal. 3. If error continues to display, possible high limit trip or heating element malfunction contact Hobart Service. 1. Press the power button to power off. 2. Restart as normal. 3. If error continues to display, possible high limit trip or heating element malfunction contact Hobart Service. 1. Press the power button off then on to start the draining process. 2. Drain tank and refill (should reset the pressure level sensors). 3. If error continues to display contact Hobart Service. 1. Verify drain hose is not pinched or kinked. 2. Verify pump strainer is not clogged. 3. If error continues to display, possible drain pump malfunction contact Hobart Service. 1. Cycle power button off and then on to continue filling. 2. Check wash and rinse arms for clogged nozzles. 3. If error continues to display contact Hobart Service. 1. Verify drain hose is not pinched, kinked or incorrect drain connection to building drain. 2. Check drain hose for any debris and drain again. 3. If error continue to display contact Hobart Service. 1. Verify supply hose is not pinched or kinked. 2. Check that water is being supplied to machine. 3. Error will clear once water fills booster to setpoint within set time. 4. If error continues to display, possible fill valve malfunction contact Hobart Service. 1. Low or no chemicals. 2. Float level on bottle level sensor below working condition. 3. If no bottle level sensor present, jumpers are missing from chemical level sensor connectors. 1. Machine is in fill, wash or delime cycle. 2. Verify door is closed. 3. If cycle running, then there is a display updating delay. 1. Rinse temperature below setpoint on 3 consecutive cycles. 2. Error will clear if rinse temperature meets or exceeds setpoint. 3. If error continues to display contact Hobart Service 1. USB not properly configured or incorrect directory path. 2. Contact Hobart Service. 1. Internal communication error 2. Contact Hobart Service. 1. Check if item(s) from previous wash cycle removed large amount of water from dishwasher. 2. Check orientation of ware to ensure water is not collected. 3. Will automatically correct after starting of the next cycle. 4. Wash tank will fill to proper level and heat to temperature and then wash cycle will resume. 1. Press the power button to power off and drain tank. 2. Restart as normal. 3. If error continue to display, unplug the machine from the wall. If unit is hardwired, turn circuit breaker off then back on. 4. If error continues to display, possible tripped high limit or heating element malfunction contact Hobart Service. 1. System exceeded maximum fill time. 2. Press the power button to power off machine. 3. Verify supply hose is not pinched or kinked. 4. Check that water is being supplied to machine. 5. Restart as normal. 6. If error continues to display, possible fill valve malfunction contact Hobart Service. NOTE: SWITCHING DISHWASHER OFF AND THEN ON "RESETS" THE SIGNALS. *IF ERROR CODE PERSISTS, CONTACT HOBART SERVICE: 1-888-4HOBART © 2021 Hobart 701 S. Ridge Avenue, Troy, OH 45373 | Phone: (937) 332-3000 | centerlinefoodequipment.com F41139 (10-21)