VT8350U5500B-Barber Colman (Schneider Electric) VT8350U5500B Low Voltage Fan Coil Controller And Zone Controller - Industrial Stores
VT8300U5000B-Barber Colman (Schneider Electric) VT8300U5000B Low Voltage Fan Coil Controller And Zone Controller - Industrial Stores
VT8300 Series Installation Guide 24 Vac Low Voltage Commercial and Hotel/Lodging HVAC Fan Coil Applications CONTENTS Installation 2 Terminal Identification & Function 3 Terminal identification 3 Wiring 4 Typical Applications 5 2 pipe systems cooling and/or heating 6 4 pipe systems cooling and heating 7 2 pipe systems cooling or heating with reheat 8 Remote Sensor Accessories 8 Home Screen Display 9 How to Enter Setup Screen 10 Appendix 11 2 INSTALLATION Location · Do not install on outside wall. · Do not install in areas with direct heat source. · Do no install near any air discharge grill. · Do not install in areas exposed to direct sunlight · Ensure Controller has sufficient air circulation. · Ensure wall surface is flat and clean. Installation 1. Remove security screw (if any) on bottom of Room Controller cover. 2. Open unit by pulling on bottom side of Room Controller (Figure 1). 3. Read FCC ID and IC label installed in cover before installing any wireless product. 4. Ensure correct side of base faces up. 5. Pull cables 6in (15cm) out from wall. 6. Align base and mark location of two mounting holes on wall (Figure 2). 7. Install anchors in wall. 8. Insert cable in central hole of base. 9. Insert screws in mounting holes on each side of base. 10. Strip each wire 1/4in (0.6cm) from end. 11. Insert each wire and screw according to wiring chart (see following pages). 12. Gently push excess wiring back into hole. 13. Gently align cover to top of base and snap in place from bottom (Figure 3). 14. Install security screw. Installation Guide VT8300 Series Figure-1 Open the cover · If replacing an existing Line Voltage FCU Controller, label wires before removal of Room Controller. · Electronic controls are static sensitive devices. Discharge yourself correctly before manipulating and installing Controller. · A short circuit or wrong wiring may permanently damage Room Controller or equipment. · All VT8300 series controls are designed for use as operating controls only and are not safety devices. Tampering with the devices or unintended application of the devices will result in a void of warranty. · This device must be installed to provide a separation distance of at least 8in (20cm) from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Figure-2 Install the base Figure-3 Reinstall cover Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 Installation Guide VT8300 Series TERMINAL IDENTIFICATION AND FUNCTION Terminal identification VT83xxU Description / Application Internal Temperature Internal Humidity 1- BO1 2- BO2 3- BO3 4- BO4 5- RC / 24 V~ Hot 6- C / 24 V~ Com 7- RH 8- BO8 9- UO9 10- UO10 11- UO11 12- UO12 13- RS485 + 14- RS485 15- RS485 Ref 16- UI16 17- UI17 18- Scom 19- UI19 20- UI20 21- Scom 22- UI22 23- UI23 24- UI24 2 & 4 Pipe Control Type = On/Off X Model Dependent Not used Fan-L Fan-M Fan-H 24 V~ Hot 24 V~ Com Aux Heat Aux Heat Normally Close Cool Valve Normally Close Heat Valve Normally Open Cool Valve Normally Open Heat Valve BACnet MS-TP + BACnet MS-TP BACnet MS-TP Ref UI16 Function UI17 Function Common UI19 Function Remote Room Sensor Common Remote Supply Sensor Not used Not used Used in applications 2 & 4 Pipe Control Type = Floating X Model Dependent Not used Fan-L Fan-M Fan-H 24 V~ Hot 24 V~ Com Aux Heat Aux Heat Close Cool Valve Close Heat Valve Open Cool Valve Open Heat Valve BACnet MS-TP + BACnet MS-TP BACnet MS-TP Ref UI16 Function UI17 Function Common UI19 Function Remote Room Sensor Common Remote Supply Sensor Not used Not used 3 2 & 4 Pipe Control Type = Analog X Model Dependent Not used Fan-L Fan-M Fan-H 24 V~ Hot 24 V~ Com Aux Heat Aux Heat Not used Not used Analog Heat valve Analog Cool Valve BACnet MS-TP + BACnet MS-TP BACnet MS-TP Ref UI16 Function UI17 Function Common UI19 Function Remote Room Sensor Common Remote Supply Sensor Not used Not used Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 4 Wiring Power and Fan (All Models) 3 Speed LOW MED HIGH 2 Speed LOW HIGH Installation Guide VT8300 Series Single Speed HIGH 24 Vac Transformer BO8 Auxilliary Output Wiring Dry contact to end device 24 V~ maximum RC (24 Vac) C (Common) R RH BO8 - Aux Heat 24 Vac power to relay RC (24 Vac) C (Common) RH BO8 - Aux Heat R Main Outputs Wiring 22PPipipeeAAppplpicliactaiotinosns Control type = On-Off 44 PPi4pipePeiApApeppAplipclipacltaiicotainotsinosns UO9 UO11 Heating / Cooling valve Com OR 24Vac Floating control CCCooommm UO10 NC UO12 NO OR 222444VVVaaaC2cccC24oC24Vom4oVamVmacacc Heating valve CCCooommm UO11 NO UO11 NC OR 222444VVVaaaC2cccC24oC24Vom4oVamVmacacc Cooling valve UO11 UO9 Heating / Cooling valve CCCooommm OCOCOClplpoolpoeessesnneeCOCneCOColpCOCoolpmeosolpomenesmesnene Analog control UO12 UO10 UO11 UO9 CCCooommm COCCOCCOColoplpooolpmomeesmsesnneeCOCneCOColpCOCoolpmeosolpomenesmesnene OCOCOClplpoolpoeessesnneeCOCneCOColpCOCoolpmeosolpomenesmesnene Heating valve Cooling valve UO12 Heating / Cooling valve CCCooommm 202020-4-4-411VV10V0aa0VaVC20cVccdd-C204odC201cc-4Vocm-401oVa1mVV0mac0VadcVcdcdcc UO11 UO12 CCCooommm C02C02C02--44o1-o14o100mmV0VmVVVaaV0C2dadcdc-0C2c4cc1o0C2c-401-om4V1o0VmVa0mVdVacVcdacdccc 202020--441-14100V0VVVVaaVC20dadcdc-C20c4cc1oC20c-401-om4V1o0VmVa0mVdVacVcdacdccc Heating valve Cooling valve Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 Installation Guide VT8300 Series TYPICAL APPLICATIONS Schematic 3 Speed Fan Normally Closed On/Off Cooling / Heating Sensor Valve Wiring 2 pipe system cooling and/or heating Control type = On / Off 2 BO2 - Fan L 3 BO3 - Fan M 4 BO4 - Fan H 5 RC (24 Vac) 6 C (Common) 24 Vac fan relays LOW MED HIGH 7 RH 8 BO8 - Aux Heat 9 UO9 NC 10 UO10 11 UO11 12 UO12 24 Vac Transformer Normally Closed Room Temperature Control Thermostat 3 Speed Fan Modulating Floating Cooling / Heating Sensor Valve Room Temperature Control Thermostat 18 Common 19 UI 19 Optional supply water temperature sensor 2 pipe system cooling and/or heating Control type = Floating 2 BO2 - Fan L 24 Vac fan relays LOW 3 BO3 - Fan M 4 BO4 - Fan H 5 RC (24 Vac) MED HIGH 6 C (Common) 7 RH 24 Vac Transformer 8 BO8 - Aux Heat 9 UO9 10 UO10 11 UO11 12 UO12 Normally Closed 18 Common 19 UI19 Optional supply water temperature sensor 5 Settings Mandatory · Pipe no = 2 pipes · CntrltTyp = On/Off · Fan Menu = (L-M-H) · FL time = N/A If cooling only set:: · SeqOpera = Cooling only If heating only set: · SeqOpera = Heating only If heat / cool auto-changeover with a local water temperature sensor set: · SeqOpera = Cooling only · UI19 = COS Mandatory · Pipe no = 2 pipes · CntrltTyp = Floating · Fan Menu = 0 (L-M-H) · FL time = as per actuator If cooling only set: · SeqOpera = Cooling only If heating only set: · SeqOpera = Heating only If heat / cool auto-changeover with a local water temperature sensor set: · SeqOpera = Cooling only · UI19 = COS Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 6 Installation Guide VT8300 Series Schematic 3 Speed Fan Modulating Analog Cooling / Heating Sensor Valve Room Temperature Control Thermostat Wiring 2 pipe system cooling and/or heating Control type = Analog 2 BO2 - Fan L 24 Vac fan relays LOW 3 BO3 - Fan M 4 BO4 - Fan H 5 RC (24 Vac) MED HIGH 6 C (Common) 7 RH 24 Vac Transformer 8 BO8 - Aux Heat 9 UO9 10 UO10 11 UO11 12 UO12 0 to 10 Vdc Normally Closed 18 Common 19 UI 19 Optional supply water temperature sensor Settings Mandatory · Pipe no = 2 pipes · CntrltTyp = Analog · Fan Menu = (L-M-H) · RA/DA = as per actuator If cooling only set: · SeqOpera = Cooling only If heating only set: · SeqOpera = Heating only If heat / cool auto-changeover with a local water temperature sensor set: · SeqOpera = Cooling only · UI19 = COS 4 pipe system cooling and heating Control type = On / Off 3 Speed Fan Normally Closed On/Off Cooling Heating Valve Valve Room Temperature Control Thermostat 2 BO2 - Fan L 24 Vac fan relays LOW 3 BO3 - Fan M MED 4 BO4 - Fan H HIGH 5 RC (24 Vac) 6 C (Common) 7 RH 8 BO8 - Aux Heat 9 UO9 NC 24 Vac Transformer Mandatory · Pipe no = 4 pipes · CntrltTyp = On/Off · Fan Menu = (L-M-H) · SeqOpera = Cool/Heat 10 UO10 11 UO11 NC 12 UO12 Heating Normally Closed Cooling 4 pipe system cooling and heating Control type = Floating 3 Speed Fan Modulating Floating 2 3 BO2 - Fan L BO3 - Fan M 24 Vac fan relays LOW MED Cooling Heating Valve Valve 4 BO4 - Fan H 5 RC (24 Vac) 6 C (Common) 7 RH 8 BO8 - Aux Heat 9 UO9 10 UO10 HIGH Mandatory · Pipe no = 4 pipes · CntrltTyp = Floating 24 Vac Transformer · Fan Menu = (L-M-H) · FL time = as per actuator · SeqOpera = Cool/Heat 11 UO11 Room Temperature Control Thermostat 12 UO12 Heating Cooling Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 Installation Guide VT8300 Series 7 Schematic 3 Speed Fan Modulating Analog Cooling Heating Valve Valve Room Temperature Control Thermostat 3 Speed Fan Modulating Floationg Cooling / Heating Valve Electric Reheat Sensor Room Temperature Control Thermostat Wiring 4 pipe system cooling and heating Control type = Analog Settings 2 BO2 - Fan L 24 Vac fan relays LOW 3 BO3 - Fan M 4 BO4 - Fan H 5 RC (24 Vac) 6 C (Common) 7 RH 8 BO8 - Aux Heat 9 UO9 10 UO10 MED HIGH 24 Vac Transformer Mandatory · Pipe no = 4 pipes · CntrltTyp = Analog · Fan Menu = (L-M-H) · RA/DA = as per actuator · SeqOpera = Cool/Heat 11 UO11 12 UO12 0 to 10 Vdc Heating 0 to 10 Vdc Cooling 2 pipe system cooling or heating with reheat Control type = Floating 2 BO2 - Fan L 24 Vac fan relays LOW 3 BO3 - Fan M MED 4 BO4 - Fan H HIGH 5 RC (24 Vac) 6 C (Common) 7 RH 8 BO8 - Aux Heat 9 UO9 10 UO10 11 UO11 12 UO12 Electric Reheat 24 Vac Transformer Normally Closed Mandatory · Pipe no = 2 pipes · CntrltTyp = Floating · Fan Menu = (L-M-H) · FL time = as per actuator · SeqOpera = Cool/Reheat · UI19 = COS 18 SCom 19 UI 19 Optional supply water temperature sensor Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 8 REMOTE SENSOR ACCESSORIES Installation Guide VT8300 Series Model no. S3010W1000 S3020W1000 Description Wall mounted temperature sensor Wall mounted temperature sensor with override button and occupancy status LED The VT8300 Room Controller is compatible with remote mount temperature sensors using 10K type 2 NTC thermistors. Note: If one or multiple sensor(s) is/are connected into the RS terminal, the internal temperature sensor is automatically disabled. Disconnecting the sensor(s) in the RS terminal will re-activate the internal sensor. Features: · Each sensor can be configured for various averaging combinations · Optional occupancy led · Optional override key VT8300 Series Controller Wiring example of single remote room sensor S3020W1000 Remote wiring 1 sensor S2-1= On, S2-2=On S3010W1000 Remote wiring 1 sensor S2-1= On, S2-2=On Common UI 20 SCom OR RS SCom RS BO8 Aux 24 Vac Com C UI17 DI Dip switch setting for: 1 sensor ON 12 S2-1 = ON S2-2 = ON Temperature vs. resistance chart for 10 Kohm NTC thermistor (R25°C = 10K±3%, B25/85°C = 3975K±1.5%) ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm ºC ºF Kohm ºC ºF -40 -40 324.3197 -20 -4 94.5149 0 32 32.1910 20 68 12.4601 40 104 -35 -31 234.4009 -15 5 71.2430 5 41 25.1119 25 77 10.0000 45 113 -30 -22 171.3474 -10 14 54.1988 10 50 19.7390 30 86 8.0694 50 122 -25 -13 126.6109 -5 23 41.5956 15 59 15.6286 35 95 6.5499 55 131 Kohm 5.3467 4.3881 3.6202 3.0016 Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 Installation Guide VT8300 Series 9 HOME SCREEN DISPLAY Hospitality User Interface Shown Date Occupancy Status Indoor Temperature Indoor Humidity Outdoor Temperature System Mode Short Network Message Time System Status Fan Status Up Arrow Increase Temperature Setpoint Actual Setpoint Down Arrow Decrease Temperature Setpoint Help Fan Mode Language Selection Temperature Units Note: User HMI is configurable and allows display functions such as Date, Time, Humidity, Outdoor Temperature, Setpoint, and others to be enabled or disabled by setting various parameters. Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 10 HOW TO ENTER SET-UP SCREEN Installation Guide VT8300 Series Touch and hold this point for 3 seconds to enter set-up mode Note: If a configuration/installer password is activated to prevent unauthorised access to the configuration menu parameters, a password entry prompt shows to prevent access to device configuration components. For more information on using and configuring the functions of the HMI, refer to the VT8300 User Interface Guide SET-UP SCREEN DISPLAY 1/2 Setup Network Configuration Setpoints - Display Service View Test Outputs Language Selection Enter BACnet® & ZigBee® network settings Enter parameter configuration menu Enter setpoint & display settings Enter status and service view Enter output testing mode Enter language selection Return to home screen Discover Mode The Controller becomes discoverable on the wireless ZigBee® network for 1 minute (this button is hidden if ZigBee® settings are not configured) General Note: Adjustable parameter Non-adjustable parameter Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016 Installation Guide VT8300 Series 11 APPENDIX A TERMINAL CORRESPONDANCE The terminals of a VT8300 are identified differently and have a wider range of possible functions compared to those of any of the VT7300 series Room Controllers. Nonetheless, there is a direct correspondance of functions between the terminals of the VT7300 series and the VT8300 series. Consult the table below to verify the appropriate terminal when replacing a VT7300 Room Controller with a VT8300 Room Controller. VT7300 Terminal name Terminal ID Binary Input 1 BI1 Binary Input 2 BI2 Universal Input 3 UI3 Sensor Common Scom Remote Sensor RS Sensor Common Scom Mix/Supply Sensor MS VT8300 Terminal name Terminal ID Universal Input 16 UI16 Universal Input 17 UI17 Universal Input 19 UI19 Terminal 18 Common COM Universal Input 20 UI20 - RS Terminal 21 Common COM Universal Input 22 UI22 - SS APPENDIX B POWER OUTAGE CLOCK RESET In the event of a power outage, VT8300 Room Controllers retain the correct time as long as the duration of the power outage is not prolonged. Depending on the duration of the power outage, the Room Controllers internal clock may need to be updated or reset completely. The following table gives an indication of the expected clock performance after a power outage. Outage duration 0 - 24 hours 24 - 36 hours 36 - 72 hours 72+ hours Room Controller behaviour Clock functions are normal Clock accuracy not guaranteed, time may need to be adjusted Clock no longer increments and must adjusted when power is restored Clock functions are fully reset, and must be reinitialized as per a new installation Viconics Technologies Inc. | 9245 Langelier Blvd. | St.-Leonard | Quebec | Canada | H1P 3K9 | Tel: (514) 321-5660 | Fax: (514) 321-4150 028-0429-03 www.viconics.com | sales@viconics.com April 2016Adobe PDF Library 10.0.1 Adobe InDesign CS6 (Windows)