Bigme Cloud Literacy Technology Co., Ltd. HIBREAK Smartphone 2A8EM-HIBREAK 2A8EMHIBREAK hibreak
Shenzhen Toby Technology Co., Ltd. Report No.: TBR-C-202406-0078-35 Page: 1 of 47 RF Test Report FCC ID: 2A8EM-HIBREAK Report No. : TBR-C-202406-0078-35 Applicant : Bigme Cloud Literacy Technology Co., Ltd. Equipment Under Test (EUT) EUT Name : Smartphone Model No. : HiBreak Series Model No. : Please refer to page 5 Brand Name : Bigme Sample ID : HC-C-202406-0078-01-01-1#&HC-C-202406-0078-01-01-2# Receipt Date : 2024-07-16 Test Date : 2024-07-16 to 2024-08-02 Issue Date : 2024-08-14 Standards : 47 CFR Part 2, 22(H), 24(E), 27 Test Method : ANSI C63.26 2015 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above. Tested By : ZKN ZHOU Reviewed By : Wade. Lv Approved By : Ivan Su This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 Report No.: TBR-C-202406-0078-35 Page: 2 of 47 Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT..............................................................................5 1.1 Client Information.................................................................................................................5 1.2 General Description of EUT (Equipment Under Test) ...................................................5 1.3 Block Diagram Showing the Configuration of System Tested ......................................8 1.4 Description of Support Units ..............................................................................................8 1.5 Measurement Uncertainty ..................................................................................................9 1.6 Test Facility...........................................................................................................................9 2. TEST SUMMARY.....................................................................................................................10 3. TEST SOFTWARE...................................................................................................................10 4. TEST EQUIPMENT AND TEST SITE...................................................................................11 5. CONDUCTED RF OUTPUT POWER ...................................................................................13 5.1 Test Standard .....................................................................................................................13 5.2 Test Setup...........................................................................................................................13 5.3 Test Procedure...................................................................................................................13 5.4 Deviation From Test Standard.........................................................................................13 5.5 EUT Operating Mode ........................................................................................................13 5.6 Test Data.............................................................................................................................13 6. PEAK-AVERAGE RATIO .......................................................................................................14 6.1 Test Standard and Limit....................................................................................................14 6.2 Test Setup...........................................................................................................................14 6.3 Test Procedure...................................................................................................................14 6.4 Deviation From Test Standard.........................................................................................14 6.5 EUT Operating Mode ........................................................................................................14 6.6 Test Data.............................................................................................................................14 7. OCCUPIED BANDWIDTH ......................................................................................................15 7.1 Test Standard and Limit....................................................................................................15 7.2 Test Setup...........................................................................................................................15 7.3 Test Procedure...................................................................................................................15 7.4 Deviation From Test Standard.........................................................................................15 7.5 EUT Operating Mode ........................................................................................................15 7.6 Test Data.............................................................................................................................15 8. OUT OF BAND EMISSION AT ANTENNA TERMINALS.................................................16 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 3 of 47 8.1 Test Standard and Limit....................................................................................................16 8.2 Test Setup...........................................................................................................................17 8.3 Test Procedure...................................................................................................................17 8.4 Deviation From Test Standard.........................................................................................17 8.5 EUT Operating Mode ........................................................................................................17 8.6 Test Data.............................................................................................................................17 9. BAND EDGE TEST..................................................................................................................18 9.1 Test Standard and Limit....................................................................................................18 9.2 Test Setup...........................................................................................................................19 9.3 Test Procedure...................................................................................................................19 9.4 Deviation From Test Standard.........................................................................................19 9.5 EUT Operating Mode ........................................................................................................19 9.6 Test Data.............................................................................................................................19 10. RADIATED OUTPUT POWER ..............................................................................................20 10.1 Test Standard and Limit .................................................................................................20 10.2 Test Setup.........................................................................................................................20 10.3 Test Procedure.................................................................................................................21 10.4 Deviation From Test Standard.......................................................................................21 10.5 EUT Operating Mode ......................................................................................................21 10.6 Test Data...........................................................................................................................21 11. RADIATED OUT BAND OF EMISSIONS ............................................................................22 11.1 Test Standard and Limit..............................................................................................22 11.2 Test Setup.........................................................................................................................22 11.3 Test Procedure.................................................................................................................22 11.4 Deviation From Test Standard.......................................................................................22 11.5 EUT Operating Mode ......................................................................................................22 11.6 Test Data...........................................................................................................................22 12. FREQUENCY STABILITY ......................................................................................................23 12.1 Test Standard and Limit..............................................................................................23 12.2 Test Setup.........................................................................................................................23 12.3 Test Procedure.................................................................................................................23 12.4 Deviation From Test Standard.......................................................................................23 12.5 EUT Operating Mode ......................................................................................................23 12.6 Test Data...........................................................................................................................23 ATTACHMENT A--RADIATED OUTPUT POWER........................................................................24 ATTACHMENT B--RADIATED OUT BAND OF EMISSIONS .....................................................36 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 4 of 47 Revision History Report No. Version TBR-C-202406-0078-35 Rev.01 Description Initial issue of report Issued Date 2024-08-14 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 5 of 47 1. General Information about EUT 1.1 Client Information Applicant : Bigme Cloud Literacy Technology Co., Ltd. Address 01 18F., COFCO PROPERTY TOWER, BAOMIN NO.1RD., : BAO AN 3RD DISTRICT, SHENZHEN, CHINA Manufacturer : Bigme Cloud Literacy Technology Co., Ltd. Address 01 18F., COFCO PROPERTY TOWER, BAOMIN NO.1RD., : BAO AN 3RD DISTRICT, SHENZHEN, CHINA 1.2 General Description of EUT (Equipment Under Test) EUT Name : Smartphone Model HiBreak, HiBreak Pro, HiBreak Plus, HiBreak Color, HiBreak Color+, HiBreak2 Pro, HiBreak2 Plus, HiBreak2 Color, HiBreak2 : Color+, HiBreak3 Pro, HiBreak3 Plus, HiBreak3 Color, HiBreak3 Color+, B531, B531 Pro, B531 Plus, B531C, B531C Pro, B531C+ Model Different Product Description Power Rating All these models are identical in the same PCB, layout and electrical : circuit, the only difference is model name. Frequency Bands: LTE Band 2: TX: 1850MHz~1910MHz LTE Band 5: TX: 824MHz~849MHz LTE Band 7: TX: 2500MHz~2570MHz LTE Band 38: TX: 2570MHz~2620MHz LTE Band 40: TX: 2305MHz~2315MHz LTE Band 41: TX: 2555MHz~2655MHz -0.74dBi FPC Antenna for LTE Band 2 -2.90dBi FPC Antenna for LTE Band 5 Antenna Gain: -1.99dBi FPC Antenna for LTE Band 7 -2.51dBi FPC Antenna for LTE Band 38 : 0.08dBi FPC Antenna for LTE Band 40 -1.26dBi FPC Antenna for LTE Band 41 Modulation Type: QPSK, 16QAM LTE Band 2: 1.4MHz/3MHz/5MHz/10MHz/15MHz/20MHz LTE Band 5: 1.4MHz/3MHz/5MHz/10MHz Bandwidth: LTE Band 7: 5MHz/10MHz/15MHz/20MHz LTE Band 38: 5MHz/10MHz/15MHz/20MHz LTE Band 40: 5MHz/10MHz LTE Band 41: 5MHz/10MHz/15MHz/20MHz Category: Cat 4 USB Input: DC 5V/2A : DC 3.8V 3300mAh 12.54Wh Rechargeable Li-ion battery TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 6 of 47 Software Version : 4.2.6 Hardware Version : V1.1 Remark: (1) The antenna gain provided by the applicant, the verified for the RF conduction test provided by TOBY test lab. (2) For a more detailed features description, please refer to the manufacturer's specifications or the User's Manual. (3) The above antenna information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications, the laboratory shall not be held responsible. TB-RF-074-1.0 (4) Channel List Test mode: LTE Band 2 Test mode: LTE Band 5 Test mode: LTE Band 7 Test mode: LTE Band 38 Test mode: LTE Band 40 Test mode: LTE Band 41 Nominal Bandwidth (MHz) 1.4 3 5 10 15 20 Nominal Bandwidth (MHz) 1.4 3 5 10 Nominal Bandwidth (MHz) 5 10 15 20 Nominal Bandwidth (MHz) 5 10 15 20 Nominal Bandwidth (MHz) 5 10 Nominal Bandwidth (MHz) 5 10 15 20 Report No.: TBR-C-202406-0078-35 Page: 7 of 47 Low (L) MHz 1850.7 1851.5 1852.5 1855.0 1857.5 1860.0 Low (L) MHz 824.7 825.5 826.5 829.0 Low (L) MHz 2502.5 2505.0 2507.5 2510.0 Low (L) MHz 2572.5 2575.0 2577.5 2580.0 Low (L) MHz 2307.5 / Low (L) MHz 2557.5 2560.0 2562.5 2565.0 RF Channel Middle (M) MHz 1880.0 1880.0 1880.0 1880.0 1880.0 1880.0 RF Channel Middle (M) MHz 836.5 836.5 836.5 836.5 RF Channel Middle (M) MHz 2535.0 2535.0 2535.0 2535.0 RF Channel Middle (M) MHz 2595.0 2595.0 2595.0 2595.0 RF Channel Middle (M) MHz 2310.0 2310.0 RF Channel Middle (M) MHz 2605.0 2605.0 2605.0 2605.0 High (H) MHz 1909.3 1908.5 1907.5 1905.0 1902.5 1900.0 High (H) MHz 848.3 847.5 846.5 844.0 High (H) MHz 2567.5 2565.0 2562.5 2560.0 High (H) MHz 2617.5 2615.0 2612.5 2610.0 High (H) MHz 2312.5 / High (H) MHz 2652.5 2650.0 2647.5 2645.0 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 8 of 47 1.3 Block Diagram Showing the Configuration of System Tested EUT Base Station The above block diagram of setup is the normal mode. And more detail please refer to the test setup of each test item of bellow. 1.4 Description of Support Units The EUT has been tested as an independent unit. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 9 of 47 1.5 Measurement Uncertainty Test Item Parameters Expanded Uncertainty (ULab) RF Power, conducted / ±0.82 dB Radiated Emission Level Accuracy: 9kHz to 30 MHz ±4.60 dB Radiated Emission Level Accuracy: 30MHz to 1000 MHz ±4.40 dB Radiated Emission Level Accuracy: Above 1000MHz ±4.20 dB 1.6 Test Facility The testing report were performed by the Shenzhen Toby Technology Co., Ltd., in their facilities located at 1/F., Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China. At the time of testing, the following bodies accredited the Laboratory: CNAS (L5813) The Laboratory has been accredited by CNAS to ISO/IEC 17025: 2017 General Requirements for the Competence of Testing and Calibration Laboratories for the competence in the field of testing. And the Registration No.: CNAS L5813. A2LA Certificate No.: 4750.01 The laboratory has been accredited by American Association for Laboratory Accreditation(A2LA) to ISO/IEC 170252017 General Requirements for the Competence of Testing and Calibration Laboratories for the technical competence in the field of Electrical Testing. And the A2LA Certificate No.: 4750.01.FCC Accredited Test Site Number: 854351. Designation Number: CN1223. IC Registration No.: (11950A) The Laboratory has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing. The site registration: Site# 11950A. CAB identifier: CN0056. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 10 of 47 2. Test Summary Test Item Section in CFR 47 Part 2.1046 Part 22.913(a)(2) RF Output Power Part 24.232(c) Part 27.50 (b)(10) Part 27.50 (d)(4) Part 27.50 (h)(2) Peak-to-Average Ratio Part 24.232(d) Part 27.50(d)(5) 99% & -26 dB Occupied Bandwidth Part 2.1049 Part 22.917(a) Part 24.238(b) Part 27.53(h) Part 27.53(m) Part 2.1051 Spurious Emissions at Antenna Terminal Part 24.238(a) Part 27.53 (h) Part 27.53(m) Field Strength of Spurious Radiation Part 2.1053 Part 22.917(a) Part 24.238(a) Part 27.53 (h) Part 27.53(m) Part 24.238(a) Out of band emission, Band Edge Part 22.917(a) Part 27.53 (h) Part 27.53(m) Frequency stability vs. temperature Part 27.54 Part 24.235 Part 22.355 Part 2.1055(a)(1)(b) Part 27.54 Frequency stability vs. voltage Part 24.235 Part 22.355 Part 2.1055(d)(2) Pass: The EUT complies with the essential requirements in the standard. 3. Test Software Test Item Radiation Emission RF Test System Test Software EZ-EMC JS1120 Manufacturer EZ Tonscend Result PASS PASS PASS PASS PASS PASS PASS PASS Version No. FA-03A2RE+ V3.1.46 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 11 of 47 4. Test Equipment and Test Site No. TB-EMCSR001 TB-EMCSR002 TB-EMCCA001 TB-EMCCB002 Test Site Shielding Chamber #1 Shielding Chamber #2 3m Anechoic Chamber #A 3m Anechoic Chamber #B Test Site Manufacturer YIHENG YIHENG ETS YIHENG Specification 7.5*4.0*3.0m 8.0*4.0*3.0m 9.0*6.0*6.0m 9.0*6.0*6.0m Used X X Radiation Emission Test (B Site) Equipment Manufacturer Model No. Spectrum Analyzer Agilent N9020A Spectrum Analyzer Rohde & Schwarz FSV40-N EMI Test Receiver Rohde & Schwarz ESU-8 Bilog Antenna SCHWARZBECK VULB 9168 Horn Antenna SCHWARZBECK BBHA 9120 D Horn Antenna SCHWARZBECK BBHA 9170 Loop Antenna SCHWARZBECK FMZB 1519 B HF Amplifier Tonscend TAP9E6343 HF Amplifier Tonscend TAP051845 HF Amplifier Tonscend TAP0184050 Highpass Filter CD HPM-6.4/18G Highpass Filter CD HPM-2.8/18G Highpass Filter XINBO XBLBQ-HTA67(8-25G) Antenna Conducted Emission Equipment Manufacturer Model No. Spectrum Analyzer Rohde & Schwarz FSV40-N MXA Signal Analyzer KEYSIGHT N9020B MXA Signal Analyzer Agilent N9020A Vector Signal Generator Agilent N5182A Analog Signal Generator Agilent N5181A Vector Signal Generator KEYSIGHT N5182B Analog Signal Generator KEYSIGHT N5173B DARE!! Instruments RadiPowerRPR3006W RF Power Sensor DARE!! Instruments RadiPowerRPR3006W DARE!! Instruments RadiPowerRPR3006W DARE!! Instruments RadiPowerRPR3006W Serial No. MY49100060 102197 100472/008 1225 2463 1118 1519B-059 AP21C806117 AP21C806141 AP21C806129 ----22052702-1 Serial No. 102197 MY60110172 MY47380425 MY50141294 MY48180463 MY59101429 MY61252685 17I00015SNO26 17I00015SNO29 17I00015SNO31 17I00015SNO33 Last Cal. Cal. Due Date Aug. 30, 2023 Aug. 29, 2024 Jun. 17, 2024 Jun. 16, 2025 Feb. 23, 2024 Feb.22, 2025 Nov. 13, 2023 Nov. 12, 2025 Jun. 14, 2024 Jun. 13, 2026 Feb. 27, 2024 Feb.26, 2026 Jun. 14, 2024 Jun. 13, 2026 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 N/A N/A N/A N/A N/A N/A Last Cal. Cal. Due Date Jun. 17, 2024 Jun. 16, 2025 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 Aug. 30, 2023 Aug. 29, 2024 TB-RF-074-1.0 RF Control Unit RF Control Unit Power Control Box Wideband Radio Comunication Tester Universal Radio Communication Tester Tonsced Tonsced Tonsced JS0806-1 JS0806-2 JS0806-4ADC Rohde & Schwarz CMW500 Rohde&Schwarz CMW500 Report No.: TBR-C-202406-0078-35 Page: 12 of 47 21C8060380 21F8060439 21C8060387 144382 N/A N/A Aug. 30, 2023 Aug. 29, 2024 N/A N/A Aug. 30, 2023 Aug. 29, 2024 168796 Feb. 23, 2024 Feb.22, 2025 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 13 of 47 5. Conducted RF Output Power 5.1 Test Standard 5.1.1 Test Standard FCC part 2.1046, FCC part 22.913(a)(2), FCC part 24.232(c), FCC Part 27.50(b)&(d), FCC Part 27.50 (h) 5.2 Test Setup 5.3 Test Procedure (1) The EUT is coupled to the Base Station with the suitable Attenuator, the path loss is calibrated to correct the reading. (2) A call is set up by the Base Station to the generic call set up procedure. (3) Set EUT at maximum power level through base station by power level command. (4) Then read record the power value from the Base Station in dBm. 5.4 Deviation From Test Standard No deviation 5.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 5.6 Test Data Please refer to the Appendix for LTE. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 14 of 47 6. Peak-Average Ratio 6.1 Test Standard and Limit 6.1.1 Test Standard FCC part 24.232(d); FCC Part 27.50(d); FCC Part 27.50 (h) 6.1.2 Test Limit Peak-to-Average Ratio The peak-to-average ratio (PAR) of the transmission may not exceed 13 dB. 6.2 Test Setup 6.3 Test Procedure According with KDB 971168 (1) The signal analyzer's CCDF measurement profile is enabled. (2) Frequency = carrier center frequency. (3) Measurement BW>Emission bandwidth of signal. (4) The signal analyzer was set to collect one million samples to generate the CCDF curve. (5) Set the EUT working in highest power level, measured and recorded the 0.1% as PAPR level. (6) The measurement interval was set depending on the type of signal analyzed. For continuous signals (>98% duty cycle), the measurement interval was set to 1ms. For burst transmissions, the spectrum analyzer is set to use an internal "RF Burst" trigger that is synced with an incoming pulse and the measurement interval is set to less than the duration of the "on time" of one burst to ensure that energy is only captured during a time in which of the transmitter is operating at maximum power. 6.4 Deviation From Test Standard No deviation 6.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 6.6 Test Data Please refer to the Appendix for LTE. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 15 of 47 7. Occupied Bandwidth 7.1 Test Standard and Limit 7.1.1 Test Standard FCC Part 2: 2.1049, FCC Part 22.917(a), FCC part 24.238(b), FCC Part 27.53(h) FCC Part 27.53(m) 7.1.2 Test Limit According to FCC section 2.1049, the occupied bandwidth is the frequency bandwidth such that below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission. Occupied bandwidth is also known as 99% power and -26dBC occupied bandwidths. 7.2 Test Setup 7.3 Test Procedure (1) The EUT was directly connected to the spectrum analyzer and Base station via power splitter as show in the block diagram above. (2) The resolution bandwidth of the Spectrum Analyzer is set to at least 1% of the occupied bandwidth. VBW= 3 times RBW. (3) The low, middle and the high channels are selected to perform tests respectively. (4) Set the frequency range of the Spectrum Analyzer suitably to capture the waveform; search peak; make a line whose value is 26dB lower than the peak; mark two points which the line intersected the waveform at; finally record the delta of the two points as the occupied bandwidth and the plot. (5) Set the Spectrum Analyzer Occupied bandwidth function to measure the 99% occupied bandwidth. 7.4 Deviation From Test Standard No deviation 7.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 7.6 Test Data Please refer to the Appendix for LTE. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 16 of 47 8. Out of Band Emission at Antenna Terminals 8.1 Test Standard and Limit 8.1.1 Test Standard FCC Part 2: 2.1051, 2.1057; FCC Part 22.917(a), FCC part 24.238(a); FCC Part 27.53 (h), FCC Part 27.53(m) 8.1.2 Test Limit In addition to the limit outlined in section 4.7.1 above, equipment operating in the frequency bands 746-756 MHz and 777-787 MHz shall also comply with the following restrictions: a) The power of any unwanted emissions in any 6.25 kHz bandwidth for all frequencies between 763-775 MHz and 793-806 MHz shall be attenuated below the transmitter power, P (dBW), by at least: (i) 76 + 10 log10 p (watts), dB, for base and fixed equipment, and (ii) 65 + 10 log10 p (watts), dB, for mobile and portable equipment. b) The e.i.r.p. in the band 1559-1610 MHz shall not exceed -70 dBW/MHz for wideband signal and -80 dBW for discrete emission with bandwidth less than 700 Hz. Mobile and base station equipment shall comply with the limits in (i) and (ii) below. (i) In the first 1.0 MHz band immediately outside and adjacent to each of the sub-bands specified in Section 5.1, the power of emissions per any 1% of the occupied bandwidth shall be attenuated (in dB) below the transmitter output power P (dBW) by at least 43 + 10 log10 p (watts). (ii) After the first 1.0 MHz immediately outside and adjacent to each of the sub-bands, the power of emissions in any 100 kHz bandwidth shall be attenuated (in dB) below the transmitter output power P (dBW) by at least 43 + 10 log10 p (watts). If the measurement is performed using 1% of the occupied bandwidth, power integration over 100 kHz is required. Equipment shall comply with the limits in (i) and (ii) below. (i) In the 1.0 MHz bands immediately outside and adjacent to the equipment's operating frequency block, the emission power per any 1% of the emission bandwidth shall be attenuated (in dB) below the transmitter output power P (dBW) by at least 43 + 10 log10 p(watts). (ii)After the first 1.0 MHz, theemissionpowerin any 1 MHz bandwidth shall be attenuated(in dB) below the transmitter output powerP (dBW) by at least 43+10log10p(watts). If themeasurement isperformedusing 1% of the emission bandwidth, power integration over 1.0MHz is required. (i) In the first 1.0 MHz bands immediately outside and adjacent to the equipment's smallest operating frequency block,2 which can contain the equipment's occupied bandwidth, the emission power per any 1% of the emission bandwidth shall be attenuated below the transmitter output power P (in dBW) by at least 43 + 10 log10 p (watts) dB. (ii) After the first 1.0 MHz outside the equipment's smallest operating frequency block, which can contain the equipment's occupied bandwidth, the emission power in any 1 MHz bandwidth shall be attenuated below the transmitter output power P (in dBW) by at least 43 + 10 log10 p (watts) dB TB-RF-074-1.0 8.2 Test Setup Report No.: TBR-C-202406-0078-35 Page: 17 of 47 8.3 Test Procedure 1 The RF output of the transceiver was connected to a spectrum analyzer through appropriate attenuation. 2 The resolution bandwidth of the spectrum analyzer was set at 100 kHz when below 1GHz, 1MHz when above 1 GHz; sufficient scans were taken to show the out of band Emissions if any up to 10th harmonic. 3 For the out of band: Set the RBW=100 kHz, VBW=300 kHz when below 1 GHz, RBW =1 MHz, VBW=3 MHz when above 1 GHz, Start=30MHz, Stop= 10th harmonic. 4 Band Edge Requirements: In the 1 MHz bands immediately outside and adjacent to the frequency block, a resolution bandwidth of at least 1 percent of the emission bandwidth of the fundamental emission of the transmitter. 8.4 Deviation From Test Standard No deviation 8.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 8.6 Test Data Please refer to the Appendix for LTE. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 18 of 47 9. Band Edge Test 9.1 Test Standard and Limit 9.1.1 Test Standard FCC Part 2: 2.1051, 2.1057; FCC Part 22.917(a), FCC part 24.238(a) FCC Part 27.53 (h), FCC Part 27.53(m) 9.1.2 Test Limit In addition to the limit outlined in section 4.7.1 above, equipment operating in the frequency bands 746-756 MHz and 777-787 MHz shall also comply with the following restrictions: a) The power of any unwanted emissions in any 6.25 kHz bandwidth for all frequencies between 763-775 MHz and 793-806 MHz shall be attenuated below the transmitter power, P (dBW), by at least: (i) 76 + 10 log10 p (watts), dB, for base and fixed equipment, and (ii) 65 + 10 log10 p (watts), dB, for mobile and portable equipment. b) The e.i.r.p. in the band 1559-1610 MHz shall not exceed -70 dBW/MHz for wideband signal and -80 dBW for discrete emission with bandwidth less than 700 Hz. Mobile and base station equipment shall comply with the limits in (i) and (ii) below. (i) In the first 1.0 MHz band immediately outside and adjacent to each of the sub-bands specified in Section 5.1, the power of emissions per any 1% of the occupied bandwidth shall be attenuated (in dB) below the transmitter output power P (dBW) by at least 43 + 10 log10 p (watts). (ii) After the first 1.0 MHz immediately outside and adjacent to each of the sub-bands, the power of emissions in any 100 kHz bandwidth shall be attenuated (in dB) below the transmitter output power P (dBW) by at least 43 + 10 log10 p (watts). If the measurement is performed using 1% of the occupied bandwidth, power integration over 100 kHz is required. Equipment shall comply with the limits in (i) and (ii) below. (i) In the 1.0 MHz bands immediately outside and adjacent to the equipment's operating frequency block, the emission power per any 1% of the emission bandwidth shall be attenuated (in dB) below the transmitter output power P (dBW) by at least 43 + 10 log10 p(watts). (ii)After the first 1.0 MHz, theemissionpowerin any 1 MHz bandwidth shall be attenuated(in dB) below the transmitter output powerP (dBW) by at least 43+10log10p(watts). If themeasurement isperformedusing 1% of the emission bandwidth, power integration over 1.0MHz is required. (i) In the first 1.0 MHz bands immediately outside and adjacent to the equipment's smallest operating frequency block,2 which can contain the equipment's occupied bandwidth, the emission power per any 1% of the emission bandwidth shall be attenuated below the transmitter output power P (in dBW) by at least 43 + 10 log10 p (watts) dB. (ii) After the first 1.0 MHz outside the equipment's smallest operating frequency block, which can contain the equipment's occupied bandwidth, the emission power in any 1 MHz bandwidth shall be attenuated below the transmitter output power P (in dBW) by at least 43 + 10 log10 p (watts) dB TB-RF-074-1.0 9.2 Test Setup Report No.: TBR-C-202406-0078-35 Page: 19 of 47 9.3 Test Procedure 1 The RF output of the transceiver was connected to a spectrum analyzer through appropriate attenuation. 2 The resolution bandwidth of the spectrum analyzer was set at 100 kHz when below 1GHz, 1MHz when above 1 GHz; sufficient scans were taken to show the out of band Emissions if any up to 10th harmonic. 3 For the out of band: Set the RBW=100 kHz, VBW=300 kHz when below 1 GHz, RBW =1 MHz, VBW=3 MHz when above 1 GHz, Start=30MHz, Stop= 10th harmonic. 4 Band Edge Requirements: In the 1 MHz bands immediately outside and adjacent to the frequency block, a resolution bandwidth of at least 1 percent of the emission bandwidth of the fundamental emission of the transmitter. 9.4 Deviation From Test Standard No deviation 9.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 9.6 Test Data Please refer to the Appendix for LTE. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 20 of 47 10. Radiated Output Power 10.1 Test Standard and Limit 10.1.1 Test Standard FCC Part 2.1046, FCC Part 22.913(a)(2), FCC part 24.232(c), FCC part 27.50(c), FCC part 27.50(d) 10.1.2 Test Limit E.I.R.P E.R.P E.I.R.P E.I.R.P LTE Band 2 LTE Band 5 LTE Band 7 LTE Band 38 2W(33dBm) 7W(38.45dBm) 2W(33dBm) 2W(33dBm) E.I.R.P LTE Band 40 E.I.R.P LTE Band 41 2W(33dBm) 2W(33dBm) 10.2 Test Setup Substituted Method TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 21 of 47 10.3 Test Procedure (1) The EUT was placed on an non-conductive rotating platform with 0.8 meter height in an anechoic chamber. The radiated emission at the fundamental frequency was measured at 3 m with a test antenna and a spectrum analyzer with RBW=3 MHz, VBW=3 MHz and peak detector settings. (2) During the measurement, the EUT was enforced in maximum power and linked with the Base Station. The highest was recorded from analyzer power level (LVT) from the 360 degrees rotation of the turntable and the test antenna raised and lowered over a range from 1 to 4 meters in both horizontally and vertically polarized orientations. (3) Effective Isotropic Radiated Power (EIRP) was measured by substitution method according to C63.26. The EUT was replaced by dipole antenna (for frequency below 1 GHz) or Horn antenna (for frequency above 1 GHz) at same location with same polarize of receiver antenna and then a known power of each measure frequency from S.G. was applied into the dipole antenna or Horn antenna through a TX cable, and then recorded the maximum Analyzer reading through raised and lowered the test antenna. Note: In test, the S.G Connect the Pre-amplifier(Sonoma 310N Pre-amplifier for frequency below 1 GHz, HP 8449B Pre-amplifier for frequency above 1 GHz ) Then the EUT's EIRP and ERP was calculated with the correction factor: ERP=S.G.Level +Antenna Gain Cord.(dB)-Cable Loss(dB) EIRP=S.G.Level+Antenna Gain Cord.(dBi)-Cable Loss(dB) 10.4 Deviation From Test Standard No deviation 10.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 10.6 Test Data Please refer to the Attachment A. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 22 of 47 11. Radiated Out Band of Emissions 11.1 Test Standard and Limit 11.1.1 Test Standard FCC Part 2: 2.1053, FCC Part 22.917(a), FCC part 24.238(a) FCC Part 27.53 (h),FCC Part 27.53(m) 11.1.2 Test Limit The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power(P) by a factor of at least 43+10log(P) dB. For all power levels +30 dBm to 0 dBm, this becomes a constant specification limit of -13 dBm. 11.2 Test Setup 11.3 Test Procedure (1) The test system setup as show in the block diagram above. (2) The EUT was placed on an non-conductive rotating platform in an anechoic chamber. The radiated spurious emissions from 30MHz to 10th harmonious of fundamental frequency were measured at 3 m with a test antenna and a spectrum analyzer with RBW=1 MHz, VBW=1 MHz, peak detector settings. (3) During the measurement, the EUT was enforced in maximum power and linked with a base station. All the spurious emissions at 3m were measured by rotation of the turntable and the test antenna raised and lowered over a range from 1 to 4 meters in both horizontally and vertically polarized orientations. (4) When found the maximum level of emissions from the EUT. Remove the EUT and replace it with substitution antenna. A signal generator was connected to the substitution antenna by a non-radiating cable. The absolute levels of the spurious emissions were measured by the substitution. Spurious emissions in dB=10 log(TX power in Watts/0.001)-the absolute level Spurious attenuation limit in dB=43+10 log(power out in Watts) 11.4 Deviation From Test Standard No deviation 11.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 11.6 Test Data Please refer to the Attachment B. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 23 of 47 12. Frequency Stability 12.1 Test Standard and Limit 12.1.1 Test Standard FCC Part 2.1055(a)(1)(b); FCC Part 22.355; FCC Part 24.235, Part 27.54 12.1.2 Test Limit ±2.5ppm 12.2 Test Setup For Temperature Test: For Voltage Test: 12.3 Test Procedure Test Procedures for Temperature Variation: (1) The EUT was set up in the thermal chamber and connected with the base station. (2) With power off, the temperature was decreased to -30 and the EUT was stabilized for three hours. Power was applied and the maximum change in frequency was recorded within one minute. (3) With power off, the temperature was raised in 10 set up to 50 and the EUT was stabilized for three hours. Power was applied and the maximum change in frequency was recorded within one minute. (4) If the EUT cannot be turned on at -30, the testing lowest temperature will be raised in 10 step until the EUT can be turned on. Test Procedures for Voltage Variation: (1) The EUT was placed in a temperature chamber at 25±5 and connected with the base station. (2) Reduce the input voltage to specify extreme voltage variation (+/- 15%) and endpoint, record the maximum frequency change. (3) The variation in frequency was measured for the worst case. 12.4 Deviation From Test Standard No deviation 12.5 EUT Operating Mode The EUT was continuously connected with the Base station and transmitting in the max power during the test. 12.6 Test Data Please refer to the Appendix for LTE. TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 24 of 47 Attachment A--Radiated Output Power Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 2 / 1.4M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.52 5.01 22.36 5.01 H 1 0 Middle V 22.35 4.82 23.24 4.82 H 1 0 Highest V 22.29 4.45 23.68 4.45 H 1 0 Lowest V 23.08 5.01 22.73 5.01 H 1 0 Middle V 23.96 4.82 23.92 4.82 H 1 0 Highest V 23.86 4.45 23.92 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 EIRP (dBm) 24.94 24.78 24.58 25.47 24.15 25.54 25.50 25.15 26.19 26.15 25.72 25.78 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 2 / 3M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.85 5.01 22.69 5.01 H 1 0 Middle V 23.75 4.82 23.11 4.82 H 1 0 Highest V 22.71 4.45 22.40 4.45 H 1 0 Lowest V 22.10 5.01 22.84 5.01 H 1 0 Middle V 23.00 4.82 22.37 4.82 H 1 0 Highest V 23.32 4.45 22.43 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 EIRP (dBm) 25.27 25.11 25.98 25.34 24.57 24.26 24.52 25.26 25.23 24.60 25.18 24.29 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 25 of 47 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 2 / 5M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.23 5.01 22.33 5.01 H 1 0 Middle V 23.00 4.82 22.65 4.82 H 1 0 Highest V 23.60 4.45 22.50 4.45 H 1 0 Lowest V 22.34 5.01 23.02 5.01 H 1 0 Middle V 22.64 4.82 23.35 4.82 H 1 0 Highest V 23.78 4.45 23.26 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 EIRP (dBm) 25.65 24.75 25.23 24.88 25.46 24.36 24.76 25.44 24.87 25.58 25.64 25.12 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 2 / 10M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.41 5.01 22.89 5.01 H 1 0 Middle V 22.54 4.82 22.60 4.82 H 1 0 Highest V 22.86 4.45 22.43 4.45 H 1 0 Lowest V 22.04 5.01 22.22 5.01 H 1 0 Middle V 23.01 4.82 22.83 4.82 H 1 0 Highest V 22.32 4.45 23.30 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 EIRP (dBm) 24.83 25.31 24.77 24.83 24.72 24.29 24.46 24.64 25.24 25.06 24.18 25.16 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 26 of 47 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 2 / 15M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.57 5.01 22.49 5.01 H 1 0 Middle V 22.87 4.82 22.04 4.82 H 1 0 Highest V 22.70 4.45 23.40 4.45 H 1 0 Lowest V 22.35 5.01 22.02 5.01 H 1 0 Middle V 23.83 4.82 23.00 4.82 H 1 0 Highest V 23.32 4.45 23.58 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 EIRP (dBm) 25.99 24.91 25.10 24.27 24.56 25.26 24.77 24.44 26.06 25.23 25.18 25.44 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 2 / 20M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.14 5.01 23.80 5.01 H 1 0 Middle V 23.20 4.82 23.36 4.82 H 1 0 Highest V 22.41 4.45 22.28 4.45 H 1 0 Lowest V 23.72 5.01 22.64 5.01 H 1 0 Middle V 22.32 4.82 22.21 4.82 H 1 0 Highest V 23.76 4.45 23.14 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 EIRP (dBm) 24.56 26.22 25.43 25.59 24.27 24.14 26.14 25.06 24.55 24.44 25.62 25.00 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 27 of 47 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 5 / 1.4M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.78 5.01 22.41 5.01 H 1 0 Middle V 23.20 4.82 23.50 4.82 H 1 0 Highest V 23.21 4.45 22.61 4.45 H 1 0 Lowest V 22.46 5.01 22.95 5.01 H 1 0 Middle V 22.27 4.82 22.36 4.82 H 1 0 Highest V 22.73 4.45 23.03 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.20 24.83 25.43 25.73 25.07 24.47 24.88 25.37 24.50 24.59 24.59 24.89 38.45 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 5 / 3M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.02 5.01 22.14 5.01 H 1 0 Middle V 23.20 4.82 23.72 4.82 H 1 0 Highest V 22.46 4.45 22.78 4.45 H 1 0 Lowest V 22.61 5.01 23.76 5.01 H 1 0 Middle V 23.50 4.82 23.11 4.82 H 1 0 Highest V 22.56 4.45 22.39 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.44 24.56 25.43 25.95 24.32 24.64 25.03 26.18 25.73 25.34 24.42 24.25 38.45 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 28 of 47 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 5 / 5M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.47 5.01 23.79 5.01 H 1 0 Middle V 23.45 4.82 22.50 4.82 H 1 0 Highest V 23.55 4.45 23.38 4.45 H 1 0 Lowest V 23.25 5.01 23.73 5.01 H 1 0 Middle V 23.80 4.82 22.64 4.82 H 1 0 Highest V 22.78 4.45 22.47 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.89 26.21 25.68 24.73 25.41 25.24 25.67 26.15 26.03 24.87 24.64 24.33 38.45 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 5 / 10M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.14 5.01 23.25 5.01 H 1 0 Middle V 22.36 4.82 22.11 4.82 H 1 0 Highest V 23.23 4.45 22.93 4.45 H 1 0 Lowest V 23.07 5.01 23.13 5.01 H 1 0 Middle V 22.52 4.82 23.11 4.82 H 1 0 Highest V 22.09 4.45 22.98 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 24.56 25.67 24.59 24.34 25.09 24.79 25.49 25.55 24.75 25.34 23.95 24.84 38.45 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 29 of 47 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 7 / 5M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.10 5.01 23.63 5.01 H 1 0 Middle V 23.11 4.82 23.54 4.82 H 1 0 Highest V 23.90 4.45 22.94 4.45 H 1 0 Lowest V 22.94 5.01 22.11 5.01 H 1 0 Middle V 22.81 4.82 22.45 4.82 H 1 0 Highest V 23.29 4.45 23.76 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.52 26.05 25.34 25.77 25.76 24.80 25.36 24.53 25.04 24.68 25.15 25.62 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 7 / 10M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.12 5.01 23.29 5.01 H 1 0 Middle V 22.26 4.82 23.95 4.82 H 1 0 Highest V 22.68 4.45 22.39 4.45 H 1 0 Lowest V 23.66 5.01 22.34 5.01 H 1 0 Middle V 23.20 4.82 22.07 4.82 H 1 0 Highest V 23.63 4.45 22.17 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 24.54 25.71 24.49 26.18 24.54 24.25 26.08 24.76 25.43 24.30 25.49 24.03 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 30 of 47 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 7 / 15M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.04 5.01 22.66 5.01 H 1 0 Middle V 23.16 4.82 22.43 4.82 H 1 0 Highest V 22.83 4.45 22.59 4.45 H 1 0 Lowest V 22.25 5.01 23.26 5.01 H 1 0 Middle V 22.37 4.82 22.31 4.82 H 1 0 Highest V 22.88 4.45 22.44 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.46 25.08 25.39 24.66 24.69 24.45 24.67 25.68 24.60 24.54 24.74 24.30 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 7 / 20M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.82 5.01 22.69 5.01 H 1 0 Middle V 23.05 4.82 23.86 4.82 H 1 0 Highest V 23.26 4.45 22.39 4.45 H 1 0 Lowest V 22.04 5.01 22.03 5.01 H 1 0 Middle V 22.84 4.82 23.00 4.82 H 1 0 Highest V 22.05 4.45 22.94 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.24 25.11 25.28 26.09 25.12 24.25 24.46 24.45 25.07 25.23 23.91 24.80 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 31 of 47 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 38 / 5M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.10 5.01 23.85 5.01 H 1 0 Middle V 22.41 4.82 23.61 4.82 H 1 0 Highest V 23.75 4.45 22.68 4.45 H 1 0 Lowest V 23.88 5.01 22.80 5.01 H 1 0 Middle V 23.19 4.82 23.29 4.82 H 1 0 Highest V 22.73 4.45 23.64 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 24.52 26.27 24.64 25.84 25.61 24.54 26.30 25.22 25.42 25.52 24.59 25.50 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 38 / 10M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.79 5.01 23.06 5.01 H 1 0 Middle V 22.69 4.82 23.45 4.82 H 1 0 Highest V 22.39 4.45 23.50 4.45 H 1 0 Lowest V 22.81 5.01 23.41 5.01 H 1 0 Middle V 23.97 4.82 23.38 4.82 H 1 0 Highest V 23.86 4.45 23.04 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.21 25.48 24.92 25.68 24.25 25.36 25.23 25.83 26.20 25.61 25.72 24.90 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 32 of 47 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 38 / 15M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.61 5.01 22.85 5.01 H 1 0 Middle V 23.23 4.82 22.73 4.82 H 1 0 Highest V 22.27 4.45 22.08 4.45 H 1 0 Lowest V 22.47 5.01 23.90 5.01 H 1 0 Middle V 23.34 4.82 23.97 4.82 H 1 0 Highest V 23.35 4.45 22.80 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.03 25.27 25.46 24.96 24.13 23.94 24.89 26.32 25.57 26.20 25.21 24.66 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 38 / 20M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.96 5.01 22.12 5.01 H 1 0 Middle V 23.73 4.82 23.61 4.82 H 1 0 Highest V 22.52 4.45 22.70 4.45 H 1 0 Lowest V 22.95 5.01 23.70 5.01 H 1 0 Middle V 22.94 4.82 22.83 4.82 H 1 0 Highest V 23.23 4.45 22.65 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.38 24.54 25.96 25.84 24.38 24.56 25.37 26.12 25.17 25.06 25.09 24.51 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 33 of 47 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 40 / 5M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.46 5.01 22.07 5.01 H 1 0 Middle V 22.33 4.82 22.70 4.82 H 1 0 Highest V 23.28 4.45 22.24 4.45 H 1 0 Lowest V 22.01 5.01 23.62 5.01 H 1 0 Middle V 22.25 4.82 23.57 4.82 H 1 0 Highest V 23.13 4.45 22.20 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 24.88 24.49 24.56 24.93 25.14 24.10 24.43 26.04 24.48 25.80 24.99 24.06 33 Modulation QPSK 16QAM Radiated Power (EIRP) for LTE Band 40 / 10M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.20 5.01 22.67 5.01 H 1 0 Middle V 22.15 4.82 22.28 4.82 H 1 0 Highest V 23.46 4.45 22.50 4.45 H 1 0 Lowest V 23.89 5.01 22.98 5.01 H 1 0 Middle V 22.96 4.82 23.27 4.82 H 1 0 Highest V 23.33 4.45 23.32 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 24.62 25.09 24.38 24.51 25.32 24.36 26.31 25.40 25.19 25.50 25.19 25.18 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 34 of 47 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 41 / 5M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.58 5.01 23.99 5.01 H 1 0 Middle V 22.90 4.82 23.25 4.82 H 1 0 Highest V 23.42 4.45 22.61 4.45 H 1 0 Lowest V 23.19 5.01 23.37 5.01 H 1 0 Middle V 23.90 4.82 23.09 4.82 H 1 0 Highest V 23.09 4.45 23.35 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.00 26.41 25.13 25.48 25.28 24.47 25.61 25.79 26.13 25.32 24.95 25.21 33 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 41 / 10M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 22.59 5.01 22.72 5.01 H 1 0 Middle V 22.46 4.82 22.58 4.82 H 1 0 Highest V 22.32 4.45 23.81 4.45 H 1 0 Lowest V 23.96 5.01 23.69 5.01 H 1 0 Middle V 22.74 4.82 23.11 4.82 H 1 0 Highest V 23.80 4.45 23.74 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.01 25.14 24.69 24.81 24.18 25.67 26.38 26.11 24.97 25.34 25.66 25.60 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 35 of 47 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 41 / 15M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.75 5.01 23.08 5.01 H 1 0 Middle V 22.03 4.82 23.25 4.82 H 1 0 Highest V 23.11 4.45 23.48 4.45 H 1 0 Lowest V 22.00 5.01 23.24 5.01 H 1 0 Middle V 22.74 4.82 22.07 4.82 H 1 0 Highest V 22.92 4.45 23.46 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 26.17 25.50 24.26 25.48 24.97 25.34 24.42 25.66 24.97 24.30 24.78 25.32 33 Modulation QPSK 16QAM Radiated Power (ERP) for LTE Band 41 / 20M RB Channel Size offset Antenna (H&V) SG Level (dBm) Antenna Factor (dBd) H 1 0 Lowest V 23.56 5.01 23.27 5.01 H 1 0 Middle V 23.52 4.82 23.69 4.82 H 1 0 Highest V 23.10 4.45 22.65 4.45 H 1 0 Lowest V 22.56 5.01 22.87 5.01 H 1 0 Middle V 22.90 4.82 22.39 4.82 H 1 0 Highest V 22.47 4.45 22.27 4.45 FCC Limit (dBm) Cable Loss (dB) 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 2.59 ERP (dBm) 25.98 25.69 25.75 25.92 24.96 24.51 24.98 25.29 25.13 24.62 24.33 24.13 33 TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 36 of 47 Attachment B--Radiated Out Band of Emissions Only showed the worst mode test data. Test mode: LTE BAND 2 20MHz (RB size 1 & RB offset 0) for QPSK Channel: Middle Horizontal TB-RF-074-1.0 Vertical Report No.: TBR-C-202406-0078-35 Page: 37 of 47 Remark: 1, The testing has been conformed to 10*1880MHz=18800MHz. 2, All other emissions more than 30 dB below the limit. 3, Emission Level= Read Level+ Antenna Correct Factor +Cable Loss TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 38 of 47 Test mode: LTE BAND 5 10MHz (RB size 1 & RB offset 0) for QPSK Channel: Middle Horizontal TB-RF-074-1.0 Vertical Report No.: TBR-C-202406-0078-35 Page: 39 of 47 Remark: 1, The testing has been conformed to 10*836.5MHz=8365MHz. 2, All other emissions more than 30 dB below the limit. 3, Emission Level= Read Level+ Antenna Correct Factor +Cable Loss TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 40 of 47 Test mode: LTE BAND 7 20MHz (RB size 1 & RB offset 0) for QPSK Channel: Middle Horizontal TB-RF-074-1.0 Vertical Report No.: TBR-C-202406-0078-35 Page: 41 of 47 Remark: 1, The testing has been conformed to 10*2535MHz=25350MHz. 2, All other emissions more than 30 dB below the limit. 3, Emission Level= Read Level+ Antenna Correct Factor +Cable Loss TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 42 of 47 Test mode: LTE BAND 38 20MHz (RB size 1 & RB offset 0) for QPSK Channel: Middle Horizontal TB-RF-074-1.0 Vertical Report No.: TBR-C-202406-0078-35 Page: 43 of 47 Remark: 1, The testing has been conformed to 10*2595MHz=25950MHz. 2, All other emissions more than 30 dB below the limit. 3, Emission Level= Read Level+ Antenna Correct Factor +Cable Loss TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 44 of 47 Test mode: LTE BAND 40 10MHz (RB size 1 & RB offset 0) for QPSK Channel: Middle Horizontal TB-RF-074-1.0 Vertical Report No.: TBR-C-202406-0078-35 Page: 45 of 47 Remark: 1, The testing has been conformed to 10*2310MHz=23100MHz. 2, All other emissions more than 30 dB below the limit. 3, Emission Level= Read Level+ Antenna Correct Factor +Cable Loss TB-RF-074-1.0 Report No.: TBR-C-202406-0078-35 Page: 46 of 47 Test mode: LTE BAND 41 20MHz (RB size 1 & RB offset 0) for QPSK Channel: Middle Horizontal TB-RF-074-1.0 Vertical Report No.: TBR-C-202406-0078-35 Page: 47 of 47 Remark: 1, The testing has been conformed to 10*2593MHz=25930MHz. 2, All other emissions more than 30 dB below the limit. 3, Emission Level= Read Level+ Antenna Correct Factor +Cable Loss -----END OF THE REPORT------ TB-RF-074-1.0PDFsharp 1.50.5147 (www sharp.com) (Original: Microsoft Word 2016) Microsoft Word 2016