Read Rules for Safe Operation and Instructions Carefully. CAUTION. Chassis. 7-shape Bolt. Blade. Front grill. Plastic nut. Motor shaft. Clutch knob.
OWNER'S MANUAL 18" Stand Fan MODEL: FS45-3ER READ AND SAVE THESE INSTRUCTIONS CAUTION Read Rules for Safe Operation and Instructions Carefully. WARNING 1. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safely feature. 2. To reduce the risk of fire or electric shock, do not use this fan with any solid state speed control device. RULES FOR SAFE OPERATION 1. Never insert fingers, pencils, or any other object through the grille when fan is running. 2. Disconnect fan when moving from one location to another. 3. Disconnect fan when removing grilles for cleaning. 4. Be sure fan is on a stable surface when operating to avoid overturning. 5. Do not use fan in window. Rain may create electrical hazard. 6. Ensure that the fan is switched off from the supply mains before removing the grille. The rules about cord and plug as below: 1. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the products. If the replacement fuse blows, a short-circuit may be present and the product Front grill Plastic nut Motor shaft should be discarded or Blade returned to an authorized Clutch knob service facility for examination and/or repair. 2. Do not operate any fan with a damaged cord or plug. Motor housing Discard fan or return to an authorized service facility for examination and/or Case repair. 3. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under Tighten Touch Rear grill switch Loosen Spinner Internal pole Thumb screw Fasten furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. Extension pole Chassis Height adjustment ring PART FIGURE 7-shape Bolt 1 ASSEMBLY OF CHASSIS & COLUMN UNIT 1. Unscrew the 7-shape Boltfrom the Extension Pole. (Fig.1) 2. Insert the extension pole into the chassis and tighten the 7-shape Bolt (Fig.2) 3. From the extension pole loosen the height adjustment ring and adjust the internal pole to the desired height. (Note: If you can't find the internal pole, it must inside the extension pole. You can pull it out from the extension pole.) (Fig.3) 4. To attach the head unit to the internal pole, loosen the thumb screw on the bottom of the head unit. Place the head unit on the internal pole and tighten the thumb screw in alignment with the groove on the internal pole. (Fig.4) CAUTION: Height adjustment ring must be fully fastened before the assembly of the motor section to the internal pole. Fig.1 Fig.2 Fig.3 Fig.4 Loosen Mounting hole Thumb screw Annular groove GRILL & FAN BLADE ASSEMBLY 1. Unscrew the spinner clockwise (or take the spinner out from the bag) and the plastic nut counterclockwise to remove both of them. Fix the rear grill to the motor then tighten the plastic nut again. (Fig. 5) 2. Insert the blade into shaft, and make sure the rotor shaft pin is fitted into groove of the blade. Turn the spinner counterclockwise to tighten the blade. (Fig. 6) 3. Fasten the front grill and the rear grill by the grill clip. (Fig. 7) 2 Fig.5 Fig.6 Fig.7 Clip OPERATING INSTRUCTIONS I. Remote Controller (Fig.8) " " ON/OFF KEY The key is for switching on the fan. The fan will be started at low speed. Press the key again, it will be switched off. " " TIMER KEY When this key is touched repeatedly, the time to be set 1, 2 and 4 hours and the correspond pilot lamp will light. If the Fig.8 lamp don't light after you touched the key, the fan will run continuously. " " SPEED KEY After the fan has started, this key serves as a speed selector in the sequence from "low-medium-high-low" when this key being touched repeated or continuously. " " MODE KEY Press this key to select mode. This key is a selector key for wind type. The wind type changes in the sequence from NORMAL---NATURAL---NORMAL wind when this key being touched repeatedly or kept in. II. Control Panel (Fig.9) These keys of the control panel may be used as same as of the remote controller. II. Oscillation Control To make the fan oscillate, press the clutch knob located on the top of the motor housing. To get the directional airflow, pull the clutch knob up to its initial position. III. Tilt Adjustment To adjust the air flow upward or downward, push the grilles lightly to the desired direction. Fig.9 IV. Height Adjustment The height of the fan can be adjusted by loosening the height adjustment ring, carefully carefully raising or lowering the fan and firmly re-tightening the height adjustment ring. 3 BATTERIES INSTRUCTIONS (not included) 1. Press down on the battery compartment cover and slide it out. 2. Insert the batteries, making sure that the positive terminals are facing the proper way. 3. Replace the cover. BATTERY WARNING AS BELOW 1. "Do not dispose of batteries in fire, batteries may explode or leak." 2. -Do not mix old and new batteries. 3. -Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. HOW TO USE THE REMOTE CONTROLLER CORRECTLY Point the remote controller at the receptor on body of the fan and press the desired button. The remote controller will work at distances of up to roughly five meters and the angle of 30 degree included between right and left from the receptor. The batteries must be removed from the remote controller before it is scrapped and that they are disposed of safely. OVERHEAT PROTECTION OF THE MOTOR The windings of the motor have a thermal-fuse that burns out and the fan switches off and temperature of the motor is no longer going up so that plastic parts of the fan don't subject to deformation so far so to be burned by the overheat if the motor is overheat for any unexpected reason. 4 USER SERVICING INSTRUCTIONS a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord. b) Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades. c) Remove fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal), then prize the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at several times and prize the fuse little by little. When one side of the fuse has been prized, then you can get the fuse out entirely. d) Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse. e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug. f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged. Notice: 1. When you replace the fuse, please don't operate suddenly or overexert, or else the product will be damage or cause accident. 2. When you feel it hard to be operated, please make sure you have got the right way. CLEANING 1. Be sure to unplug from the electrical supply source before cleaning. 2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly to remove soap film with clean water. 3. Be sure not to make water or other liquid enter inside of motor. 5 SERVICE & SUPPORT In the event of a warranty claim or if service is required for this product, please contact us at the following: Toll Free: 1-866-646-4332 Email us at: ccustomerservice@supportuscenter.com For questions or comments, please write to: Midea America Corporation Customer Care Center 11411 NW 107th Street, Suite 12 Miami, FL 33178 For your records, staple your sales receipt to this manual and record the following: DATE OF PURCHASE: PLACE OF PURCHASE: (STAPLE SALES RECEIPT HERE) NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS PRINTED IN CHINA 6 ONE (1) YEAR LIMITED WARRANTY Please read all instructions before attempting to use this product. Please return the Warranty Registration card within fifteen (15) days from the date of purchasing this product. Midea America Corporation, referred to hereafter as Midea America, warrants as limited herein to the original purchaser of retail that each new Pelonis Fan, shall be free of defects in material and workmanship for a period of one (1) year from the date of original purchase. This one (1) year warranty is limited to the fan motor, fan blades, and electric control circuit board. In the event of malfunctions or failure of your Pelonis Fan, simply deliver or send the product, postage prepaid along with PROOF OF PURCHASE, within the warranty period of one (1) year, to Midea America. Midea America reserves the right to inspect the claimed defective part or parts to determine if the defect or malfunction complaint is covered by this warranty. Midea America shall, within sixty (60) days after receipt of the product, at its option, repair and/or replace the defective part or parts free of charge. This warranty shall only cover defects arising from normal usage. Midea America assumes no responsibility whatsoever if the Pelonis Fan should fail during the warranty period by reasons of: Misuse, negligence, physical damage or accidents. Lack of maintenance (see cleaning). Repair by any unauthorized party during the warranty period. Damage caused by connection to an improper input voltage (see specifications). Midea America makes no further warranties or representations, express or implied except those contained herein. No representative or dealer is authorized to assume any other liability regarding the Pelonis Fan. The duration of the implied warranty granted under State law, including warranties of merchantability and fitness for particular purpose are limited in duration should the duration of the express warranty grant it hereunder. Midea America shall in no event be liable for direct, indirect, special or consequential damages. Some states do not allow limitations on how long an implied warranty lasts, and/or the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state to state. Should your Pelonis Fan fail to operate under the terms of this limited warranty, contact Midea America at 1-866-646-4332 (M-F 9:00am to 5:00pm CST). 7Adobe PDF library 15.00 Adobe Illustrator(R) 17.0