LED Desk Lamp with Color Changing Base and USB
F 90° G E A L JH A LED Desk Lamp with Color Changing Base MCC00Z MCC00Z-SHPR 1377932 INS190526 30° K 30° B D C ENGLISH CONGRATULATIONS! You've purchased the finest in natural lighting technology with your new OttLite® product. WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete. NOTE: THIS UNIT IS FULLY ASSEMBLED 1. Remove lamp from packing, placing lamp body base (A) flat on a steady surface. 2. Connect the AC Adapter input (H) into connector (J) in the rear-bottom of the lamp. 3. Plug the A/C adapter (K) into a standard household 120V AC outlet. Note: Only use with the supplied power adapter to avoid damage or fire. 4. This lamp provides 3 color modes and 3 levels of brightness. 5. Power switch (B) is a "touch" switch that controls ON/OFF power, the LED brightness settings and the color mode function of the lamp. 6. To power LED settings, slightly touch the switch to achieve the following: · Turn lamp "ON" to 1st brightness setting; touch the switch "once"; · for 2nd brightness setting; touch the switch "two-times"; · for 3rd brightness setting; touch the switch "three-times"; · to turn lamp "OFF"; touch the switch "four-times". 7. This lamp provides three color modes. To adjust lighting color mode slightly "press and hold" switch (B) for three seconds to switch light color temperature mode; 5000K, 3000K, 4000K. NOTE: 5000K is the default color mode. 8. This lamp features a Color Changing Base on lamp body base (A). 9. The Color Changing Base can be turned ON & OFF by using power switch (C) located on bottom of the light changing bar or wheel (D). For operation, turn the Color Changing Base light bar to "ON" status. To engage function for different colors, · Touch desired color represented within color wheel; · Slide finger along color wheel in either direction; · Or touch the Color Changing Base light power switch (C) for "three seconds" and watch light color change automatically. 10. To reposition the light, hold the lamp base (A) steady and grasp either flex-neck (E) or shade (F) depending on needed adjustment. Take care not to overextend the lamp to avoid unbalancing it and damage. Please refer to diagrams for lamp maximum adjustment range. LED Desk Lamp with Color Changing Base CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY. CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED. FCC PART 15 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that of the receiver. · Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (B)/NMB-005 (B) CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite's responsibility for proper function of product. POWER ADAPTER SPECIFICATION: Input: AC 100-240V, 50/60 Hz, 0.8A Output: 12V DC, 1.5A with a Male DC Plug THIS LAMP CONTAINS a 5V, 2,1A USB output port (L) located on the bottom rear of lamp. USB port can charge items such as tablets, cellular phones, etc. SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS 1. Turn lamp off and WAIT UNTIL LAMP HEAD (F) IS COOL before handling. 2. The LED panel (G) might get hot after several hours of continuous use DO NOT place your hands directly on LED light panel. 3. Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord. 4. Do not alter the plug. 5. The lamp head included with this unit cannot be replaced by the consumer. 6. INDOOR USE ONLY. NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product. H2A REV031120Adobe PDF Library 15.0 Adobe InDesign 15.0 (Macintosh)