MOMAN H2 PRO Headset Helmet Intercom

Product Care

Please keep the product in a dry, clean, and dust-free environment. Keep corrosive chemicals, liquids, and heat sources away from the product to avoid mechanical damage. Use only a soft, dry cloth to clean the product. Malfunction may be caused by dropping or impact from external force. Do not attempt to disassemble the product, as this will void the warranty. Please have the product checked or repaired by authorized technicians in case of malfunction. Failure to follow all instructions may result in mechanical damage. The warranty does not apply to human errors.

Package List

• Intercom x 2 (x 1 for 1-Rider Kit)
• Velcro Clamp x 2 (x 1 for 1-Rider Kit)
• Rear Clip x 2 (x 1 for 1-Rider Kit)
• Hook-and-Loop Fasteners x 2 (x 1 for 1-Rider Kit)
• Replaceable Hard Mic and Soft Mic Speakers x 2 (x 1 for 1-Rider Kit)
• Manual x 1
• USB Cable x 2 (x 1 for 1-Rider Kit)
• Screwdriver x 2 (x 1 for 1-Rider Kit)
• Helmet Velcro x 8 (x 4 for 1-Rider Kit)

Product Presentation

Key Components:

• On/Off Button: Powers the device on/off.
• Indicator Light: Shows device status (e.g., charging, pairing).
• Function Button: Used for various operations like answering calls, pausing music.
• Charging Interface: USB Type-C port for charging.
• Rotary Button: Used for volume control and navigating music tracks.
• Headset Interface: Port for connecting the helmet headset.
• Back with Buckle: Attachment point for clips.
• Speaker: Audio output for the helmet.
• Headset Jack: Connection point for the headset cable.
• Microphone Adapter: Connects the microphone to the headset.
• Replaceable Hard Microphone: For clear voice transmission.
• Replaceable Soft Microphone: Alternative microphone option.

Important Note: Before installing the headsets, follow the quick manual instructions to connect your phone and check sound and volume. If there is a significant difference in sound effect and volume after installation on the helmet, please adjust the speaker position inside the helmet.

Operation

1. Power On/Off
   • ON: Press and hold the On/Off button for 2 seconds. The indicator light shows alternating RED and BLUE flashes.
   • OFF: Press and hold the On/Off button for 4 seconds. The indicator light shows a single RED flash.
   • Reset: Once powered on, press and hold the power button for 8 seconds.
2. Phone Control
   • Answer Incoming Call (Manual): Briefly press the Function button.
   • Answer Incoming Call (Automatic): No operation needed after 8 seconds.
   • Reject Call: Press and hold the Function button for 3 seconds.
   • Redial Last Call: With Bluetooth disconnected, double-click the On/Off button.
   • Automatic Answer Mode: Without Bluetooth connection, double-click the On/Off button. The indicator light flashes BLUE twice when enabled, and RED twice when disabled.
   • End Call: Briefly press the Function button.
3. Music Control
   • Play/Pause: With Bluetooth connected, briefly press the Function button once.
   • Previous Song: Turn the Rotary button counter-clockwise.
   • Next Song: Turn the Rotary button clockwise.
   • Volume Up: Turn the Rotary button counter-clockwise and then HOLD.
   • Volume Down: Turn the Rotary button clockwise and then HOLD.

   [Audio alert] indicates if the volume is too high or too low.

4. FM Radio
   • ON: In standby mode, double-click the Function button twice.
   • OFF: Double-click the Function button.
   • Select Channels: Quickly turn and release the button to select and adjust channels.

   Notes: If the signal is weak indoors, try turning on the FM radio near a window or in an open area. The FM radio will automatically mute when there is an incoming phone call and will resume after the call ends.

5. Language Change

   Turn on the device, press and hold the On/Off button and the Rotary button simultaneously. Available languages: English, Japanese, Italian.

6. Voice Assistant

   With Bluetooth connected, press the Function button for 1 second. A voice prompt "Di" will be heard.

7. Pairing and Disconnection
   • 7.1 Pairing with a Phone: After powering on, press and hold the On/Off button and the Function button simultaneously for 4 seconds. The indicator light flashes BLUE twice, then RED and BLUE flash alternately. Activate your phone's Bluetooth, search for "MOMAN H2 PRO" to connect. Voice prompt: "Bluetooth connected".
   • 7.2 Pairing Two Intercoms: After powering on, press and hold the On/Off button and the Function button simultaneously for 4 seconds. The indicator light flashes BLUE twice, then RED and BLUE flash alternately. Press the On/Off button on one intercom; its indicator light flashes rapidly. Voice prompt: "Intercom Search". The two intercoms will pair successfully, indicated by a slow BLUE flashing light on both. Voice prompt: "Bluetooth Connected".
     • Note 1: Automatic Connection: Once intercoms are successfully paired, they do not need to be paired repeatedly.
     • Note 2: After powering on, briefly press the On/Off button in standby mode to repair.
   • 7.3 Reconnection and Disconnection
     • Reconnect: Briefly press the On/Off button. Voice prompt: "Di".
     • Disconnect: Briefly press the On/Off button. Voice prompt: "Di".

     Note: After five minutes of disconnection, it will reconnect automatically. If disconnected for longer than five minutes, briefly press the On/Off button to search for reconnection.

8. Music Sharing
   • To Enable (ON):
     • Connect Intercom A to Bluetooth.
     • Pair Intercom A with Intercom B.
     • Disconnect Intercom A and Intercom B (this step seems contradictory, likely means disconnect from phone if applicable, or ensure they are paired to each other).
     • Intercom A is playing music.
     • Press and hold the Function button on Intercom A. After hearing the "Di" voice prompt, continue holding the Function button for 2 more seconds. Music sharing is successful when you hear a voice prompt.

     [Diagram showing A and B intercoms, then A playing music, then A pressing and holding function button]

     • To Disable (OFF): Press and hold the Function button on Intercom A for 2 seconds.

     Note: Music can only be shared by the main device. The auxiliary device cannot share music. (Judgment: The intercom that actively initiates pairing is the main device). You can switch between main and auxiliary roles only after restoring factory settings and re-pairing. If Intercom A's music is paused and Intercom B is playing, Intercom A will play Intercom B's music. If Intercom B's music is paused, Intercom A will play Intercom B's music.

9. Multi-mode Switch
   • Between Intercom and Music/FM Radio: In Intercom mode, briefly press the On/Off button. Voice prompt: "Di". This exits Intercom mode and enters Music/FM Radio mode.
   • Between Intercom and Phone Calls:
     • In Intercom mode, when a call arrives, exit Intercom mode to answer the call.
     • After the call ends, automatically enter Intercom mode within 5 seconds.
10. Function Priority
    1. Level 1: Mobile Phone
    2. Level 2: Intercom
    3. Level 3: Music/FM Radio

Installation

1. Method 1: Install with Rear Clip
   • Use the screwdriver to loosen the screws on the rear clip so it can open properly.
   • Open the helmet liner, insert the clip into the correct position on the left side of the helmet, and tighten the screws.
   • Slide the intercom unit into the slot on the rear clip to ensure it is firmly attached.
   • Open the helmet liner (ear position), clean the EPS surface of the helmet, and stick a piece of horn-shaped Velcro on the left and right sides of the helmet.
   • Attach the speaker to the fixed Velcro surface; the speaker with the short wire should be installed near the main unit. Secure the microphone and arrange the helmet liner and cable.
   • Insert the headset into the intercom's interface and attach the headset cable.

   [Diagram showing steps for clip installation: loosening screws, inserting clip, attaching intercom, applying velcro, attaching speaker/mic, connecting headset]

2. Method 2: Install with Velcro Clip

   Separate the hook-and-loop fasteners. First, stick the hook onto the Velcro clip; choose the correct installation position on the helmet and stick the loop fastener in that position. Install the intercom onto the Velcro clip. The installation of speakers can refer to the description above.

   [Diagram showing steps for velcro clip installation: separating fasteners, attaching hook to clip, attaching loop to helmet, mounting intercom]

How to remove the intercom from the helmet

First, unplug the headset. Then, press with a finger on the fixed buckle in the middle of the rear clip (push towards the helmet side) so that the hook of the rear clip detaches from the intercom. Then, push the intercom upwards to gently slide it off the rear clip to complete the disassembly.

[Diagram showing how to detach the intercom from the clip]

3. Secure the headset connector (if necessary)

Use a screwdriver to loosen the screws on the back of the intercom. Open the buckle door, insert the headset plug, and tighten the screws. If you need to unplug the headset, open the buckle door by loosening the screws.

[Diagram showing securing the headset connector]

Charging Notes

1. Before using the Bluetooth intercom, please use the included charging cable to charge it. Connect the small Type-C interface on the charging line to the USB charging interface of the Bluetooth intercom, and connect the large USB connector of the charging cable to a power source: A. Computer USB interface; B. A mobile power bank with DC 5V output; C. A USB power adapter with DC 5V output.
2. During charging, the RED LED is always on. Once fully charged, the RED light turns off slowly. It takes up to 2.5 hours for a full charge.

Specifications

Notes

1. If you do not use the intercom for one month or more, please charge it once every two months to protect the lithium battery.
2. The storage temperature for this product is -20°C to 50°C. Do not store in environments that are too high or too low in temperature, as this will affect the product's lifespan.
3. Do not expose this product to fire to avoid explosion.
4. Only the two screws on the back of the intercom can be opened. Do not open other screws on the intercom to avoid short-circuiting the main board or damaging the battery.

Contact Information

Moman (UK) Limited
Unit 25 Basepoint Business Centre, Aviation Park, West Christchurch, United Kingdom BH23 6NX
www.momanx.com
@MomanGlobal
https://moman.co/youtubeadditional