Lithonia Lighting MSL LED Low Bay

Features & Specifications

Intended Use: The MS Series LED is a linear solution ideal for open-ceiling or suspended applications with mounting heights from 14 to 20 feet. It can be mounted in a continuous row or as a stand-alone unit. Its full-body construction and multiple mounting options adapt to a wide variety of suspended and open-ceiling applications.

Construction: The full-body housing and optical assembly is precision-formed using 20-gauge steel. The optical assembly ships factory-installed into the housing and utilizes aircraft cable tethers to support the optical assembly during wiring. The lensing integrates seamlessly into the optical housing to provide a sealed chamber to mitigate dust and insect collection. A convenient access plate is located on the back of the channel for access to the wiring compartment.

Finish: High-gloss, baked white enamel finish. Five-stage iron phosphate pretreatment ensures superior paint adhesion and rust resistance.

Optics: Optical design distributes light in the 0-60 degree zone, providing better utilization of light on task. Each linear bar is outfitted with premium, anodized MIRO 5® aluminum to ensure the highest lumens per watt can be achieved. A diffuse acrylic lens eliminates pixels to minimize glare and improve uniformity.

Electrical: The MSL luminaire has 94% lumen maintenance at 60,000 hours with an expected life of greater than 100,000 hours. The MSL ships standard with a thermally protected dimming driver that dims down to 5% using 0-10V controls. Optional EldoLED driver allows for flicker-free dimming down to 1%. LEDs are driven to provide optimal lumens per watt and less heat to extend component life. The driver and optical housing are connected with a mating plug for easy removal or future upgrade. Optional PLR through-wire harnesses are available for continuous-row installations.

Installation: A variety of mounting arrangements are available including tong hangers, aircraft cables, and stems. Suitable for mounting in continuous-row or individual mounting. End caps include knockouts for through wiring and fixture attachment in row-mounting applications.

Listings: UL and cUL listed to US and Canadian standards. For use in damp and dry locations with ambient temperatures ranging from -20°C (-4°F) to 30°C (86°F).

Buy American Act: Product with the BAA option is assembled in the USA and meets the Buy America(n) government procurement requirements under FAR, DFARS and DOT regulations. Refer to www.acuitybrands.com/buy-american for additional information.

Specifications

Warranty: 5-year limited warranty. Complete warranty terms located at: www.acuitybrands.com/support/warranty/terms-and-conditions

Note: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25°C. Specifications subject to change without notice.

Ordering Information

Lead times will vary depending on options selected. Consult with your sales representative.

Options

• Finish: WH White, MB Matte black
• Cord sets: CS1W 6' white cord-set, straight blade NEMA 5-15P, 120V; CS11W 6' white cord-set, twist-lock NEMA L7-15P, 277V; CS93W 600V SEOOW white cord, no plug; CS93W4C 6FT 600V SO white cord, 4 conductor
• Motion sensors: LCOZU Aisle motion sensor, pre-wired; LCHOSZU Aisle motion sensor, pre-wired; programmable dimming; LAPZU Aisle motion sensor with photocell, pre-wired; LAOZU 360° motion sensor, pre-wired; LAHOSZU 360° motion sensor, pre-wired; programmable dimming; LAPZU 360° motion sensor with photocell, pre-wired
• Other Options: E7W Emergency battery pack, 7W (not available for California); E10WLCP EM Self-Diagnostic battery pack, 10W Constant Power, Certified in CA Title 20 MAEDBS; PLR1G Single-circuit, plug-in wiring; PLR22G Two-circuit alternating plug-in wiring; PLR1LVG Single-circuit plug-in wiring with low voltage leads; GLR Internal fast-blow fuse; CRE Continuous row end (one hole for wiring to row, one flattened knockout to terminate the row); CRM Continuous row middle (both end plates have holes for row wiring); BAA Buy America(n) Act Compliant

Mounting Data

For unit or row installation, surface or stem mounting.

Unit installation: Minimum of two hangers required.

Row installation: One hanger per channel plus one per row required.

Hanging devices: THMSHB J2, SQ

Knockout dimensions: A = 7/8" (2.2 cm) KO, B = 3/4" (1.9 cm) KO, C = 2-3/8" (6.0 cm) KO, D = 1-1/4" (3.2 cm) KO, E = 2-3/8" (6.0 cm) KO, F = 1-3/8" (3.5 cm)

CRE - Continuous Row End: For beginning of row.

CRM - Continuous Row Mount: For middle fixture.

Dimensions

All dimensions are in inches (centimeters) unless otherwise indicated.

MSL: Length 96" (243.8 cm), Width 3 3/4" (9.52 cm), Depth 3 3/4" (9.52 cm)

TMSL: Length 48" (121.9 cm), Width 3 3/4" (9.52 cm), Depth 3 3/4" (9.52 cm)

Photometrics

See www.lithonia.com.

LSXR - Fixture Mount Sensor

For additional information, see www.sensorswitch.com.

• Four interchangeable lenses.
• Integrated mounting bracket drops lens down 3" from chase nipple.
• Single or dual relay versions - designed with robust protection from the harsh switching requirements of T5 and LED loads.
• Photocell and 0-10VDC dimming options.
• No PIR field calibration or sensitivity adjustments required.

LSXR Configuration

Note: For shortest lead times, use one of the following LSXR configurations.

Selections below will extend order lead time. Consult your sales representative for details.

Single Relay

Dual Relay (Available with 120, 277, and 347V only)

Replacement lenses: Order as separate catalog number.

Operational Data

Projected Lumen Maintenance