14-18V ONE Dual Chemistry Car Battery Charger - BCL1418IV |
BCL1418IV 14.4 - 18 VOLT IN-VEHICLE CHARGER OWNER'S OPERATING MANUAL ORIGINAL INSTRUCTIONS DESCRIPTION 1. Green LED 2. Red LED 3. Battery port 4. 12 V adapter 5. "Key hole" hanger 6. Depress latches to remove battery pack 7. Charged indicator 8. Charging indicator 9. Defective indicator 10. Testing indicator 11. Power on indicator 12. Fuse cap 13. Fuse 4-1/8 in. (105 mm) 3 2 1 4 6 5 Fig. 1 11 10 98 7 Fig. 2 WARNING onmlyawniuthal8fAor25c0orVrefucFstoecr.hcRaoregnfietnirngtuoleovcdeahptiiroconlte.e'sctoiopnerator's Fig. 3 4 13 12 Fig. 4 Important! The product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervision. English SAFETY INSTRUCTIONS Please read and observe these instructions before using the device. Before using the device check that the mains cable and mains plug are not damaged. The device must not be damp, neither should it be used in a damp environment. Do not use the device if it has suffered any heavy shock or jolting, or is damaged in any other way. Due to the heat generated during charging, the battery charger should not be operated on a combustible surface/in an inflammable environment. Do not cover the ventilating slits. Never disassemble the device yourself. Pull the plug of the battery charger out of the socket when it is not in use or when cleaning it. Only use extension cable that is approved and technically in perfect condition. During operation provide sufficient ventilation. Malfunction during charging can be caused by storing and operating in places where the temperature exceeds +40°C (+104°F); this should be avoided. Battery charging in closed cupboards, near heat sources (radiators, bright sunshine) causes heat to accumulate and can damage the device. If the battery is not going to be used for a longer period, pull the battery off the battery charger and pull out the mains plug. Protect battery contact to avoid a short circuit caused by metallic object that can cause a fire or explosion! Only charge original recommended batteries. If the power cord is damaged, it must be replaced by an Authorised Service Center in order to avoid a hazard. WARNING Do not recharge primary cells (non-rechargeable). OPERATION WARNING Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this product for the following purpose: Charging compatible 14.4V and 18V battery packs. CAUTION If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. Do not insert another battery. Return the charger and battery to your nearest service center for service or replacement. CAUTION Always place the charger on a rigid surface, not a car seat, while charging battery pack. Do not place anything such as a jacket over the charger while it is in use. WARNING Damage to property - Mains voltage must correspond with the voltage specifications on the device. CAUTION Charge in a well ventilated area. Do not block charger vents. Keep them clear to allow proper ventilation. BATTERY PROTECTION FEATURES Ryobi 14.4V and 18V lithium-ion batteries are designed with features that protect the lithium-ion cells and maximize battery life. 4 English If the tool stops during use, release the trigger to reset and resume operation. If the tool still does not work, the battery needs to be recharged. Note: The LED charge indicator light will not work if the battery protection feature has caused the battery pack to stop powering the tool. When the battery pack resets itself, the LED will again function. LED FUNCTIONS OF CHARGER See figure 2 Charger LED indicator Battery pack status Red LED Green LED Action Without Power battery ON pack Evaluate Hot battery pack Flashing Evaluate Cold battery pack Flashing Evaluate Deeply discharged Flashing OFF OFF OFF OFF Ready to charge battery pack. When battery pack reaches cooled temperature, charger begins fast charge mode. When battery pack reaches warmed temperature, charger begins fast charge mode. Charger pre-charges battery until nomal voltage is reached, then begins fast charge mode. Battery pack Defective Defective Flashing Flashing or charger is defective. · If defective, try to repeat the conditions a second time by removing and reinstalling the battery pack. If the LED status repeats a second time, try charging a different battery. · If a different battery charges normally, dispose of the defective pack. · If a different battery also indicates "Defective," the charger may be defective. Charging Fast charging ON Flashing -- Fast charging is complete; Full -- OFF ON charger maintains charge mode. Note: There is a low input voltage audible alarm for less than 10.5 V DC input. The charger will shut off when input voltage is less than 10.5 V or more than 15 V. CHARGING THE BATTERY PACK This charger will accept Ryobi 14.4V and 18V lithium-ion battery packs and Ryobi 14.4V and 18V nickel-cadmium battery packs. Use only these Ryobi 14.4V and 18V battery packs with this charger. Compatible Battery Voltage Pack Charger Input Chemistry Battery Capacity No. of Cell per Battery 130224052 130427003 14.4 V 1.3 Ah 12 Ni-cd 1.5 Ah 12 BPL1414 Li-ion 1.4 Ah 4 ABP-1815 1.5 Ah 15 ABP-1813 1.3 Ah 15 ABP1801G ABP1802G 220V-240V, Ni-cd 1.7 Ah 15 50Hz-60Hz AC only 1.7 Ah 15 RB18N15 18 V 1.5 Ah 15 BPL-1815 1.4 Ah 5 BPL-1820 BPL18202PK 2.4 Ah 10 Li-ion 2.4 Ah 10 RB18L13 1.3 Ah 5 RB18L15 1.5 Ah 5 RB18L25 2.5 Ah 5 RB18L26 2.6 Ah 10 RB18L40 4.0 Ah 10 RB18LL40 4.0 Ah 10 Battery packs for this tool are shipped in a low charge condition to prevent possible problems. Therefore, you should charge them until the green LED on the front of the charger comes on. CHARGING A BATTERY PACK If the charger does not charge the battery pack under normal circumstances, return both the battery pack and charger to your nearest authorized service center for electrical check. Use battery pack only with the recommended charger. Connect the charger to the power supply. Make sure the power supply is 12 V DC. 5 English Make sure the latches on each side of the battery pack snap into place and the battery pack is secured in the charger before beginning operation. Place the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger. Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger. Do not place the charger and battery pack in an area of extreme heat or cold. They will work best at normal room temperature. Note: The charger and battery pack should be placed in a location where the temperature is more than 10°C (50°F) but less than 38°C (100°F). The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. After charging is complete, the green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply. When batteries become fully charged, unplug the charger from the power supply and remove the battery pack. To remove the battery pack from the charger, depress the latches on each side of the battery pack. CHARGING A HOT BATTERY PACK If the battery pack is above normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery pack cools down to approximately 50°C (122°F), the charger will automatically begin fast charge mode. CHARGING A COOL BATTERY PACK If the battery pack is below normal temperature range, the red LED will begin flashing and the green LED will be off. When the battery warms to a temperature of more than 0°C (32°F), the charger will automatically begin charge mode. COLD WEATHER OPERATION The lithium-ion battery pack can be used in temperatures down to -20°C (-4°F). Put the battery pack on a tool and use the tool in a light duty application. After about a minute, the pack will have warmed up and begin operating normally. ENERGIZING BATTERY CHARGER See figure 3 By holding the connector firmly, place connector into a cigarette lighter receptacle or "power point" to energize battery charger; red power LED will come on. CAUTION If the 12 V adapter does not fit firmly into the cigarette lighter receptacle or power point, the receptacle may not be suitable for use with the charger. A poor connection at the base of the 12 V adapter could lead to electrical problems in the vehicle outside of the protections offered by the vehicle or charger's fuse. MAINTENANCE WARNING When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil and grease. WARNING Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. CHANGING FUSE See figure 4 The 12 V adapter contains a 250 V 8 Amp fuse to protect the adapter and charger from unexpected power surges. To replace the fuse: Unscrew the fuse cap on the top of the 12 V adapter. Replace old fuse with new one. If spring comes out, be sure to reinsert it before replacing new fuse. Thread fuse cap back onto adapter. Tighten securely. BATTERIES This charger will accept Ryobi 14.4V and 18V lithiumion batteries or Ryobi 14.4V and 18V nickel-cadmium batteries. Length of service from each charging will depend on the type of work you are doing. 6 English Batteries have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn. To obtain the longest possible battery life, we suggest the following: For lithium-ion batteries: Remove the battery pack from the charger once it is fully charged and ready for use. For battery pack storage longer than 30 days: Store the battery pack where the temperature is below 27°C (80°F) and away from moisture. Store battery packs in a 30%-50% charged condition. Every six months of storage, charge the pack as normal. For nickel-cadmium batteries: Remove the battery pack from the charger once it is fully charged and ready for use. For battery pack storage longer than 30 days: Store the battery pack where the temperature is below 27°C (80°F). Store battery packs in a "discharged" condition. WARNING Upon removal, cover the battery pack's terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components. Lithium-ion and nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury. ENVIRONMENTAL PROTECTION Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling. SYMBOLS Safety alert 7 GOST-R conformity Please read the instructions carefully before starting the machine. Class II equipment CE conformity Indoor use Time-lag fuse 3.15A Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. Techtronic Industries (Australia) Pty. Ltd. Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia Techtronic Industries New Zealand Ltd. 18-26 Amelia Earhart Avenue Mangere, Auckland 2022, New Zealand 961067990-03Adobe InDesign CS5 (7.0.3) Adobe PDF Library 9.9