Sealey - Leading Professional Tool & Workshop Equipment Supplier
Instruction Manual for SEALEY models including: STSXL Trike 3 Motorcycle Garage Shelter, STSXL, Trike 3 Motorcycle Garage Shelter, Motorcycle Garage Shelter, Garage Shelter
TRIKE/3 MOTORCYCLE GARAGE SHELTER 2100 X 3800 X 1900MM
File Info : application/pdf, 3 Pages, 1.21MB
DocumentDocumentTRIKE/3 MOTORCYCLE GARAGE SHELTER 2100 X 3800 X 1900MM MODEL NO: STSXL Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. Refer to Wear protective Wear eye instructions gloves during protection during assembly assembly 1. SAFETY NOTE: this is a temporary structure and is not recommended as a permanent structure. 9 This shelter is intended to offer protection from damages caused by the sun, light rain, light snow, tree sap, bird and animal excrement. 8 DO NOT use the shelter to shield goods from high winds, heavy snow or ice storms. Only use it for its intended purpose. 9 Choose the shelter's location carefully. 9 Check for overhead utility lines, branches, etc. 8 DO NOT install near roofs or structures that may shed snow, ice or excessive run-off. 8 DO NOT install near electrical wires. 9 Have an overview of all parts before attempting installation. Make sure all 8 components are available. DO NOT use this product in environments for which it is not intended (i.e. extreme CONTENTS cold, high winds, extreme heat, heavy rainfall, etc). 9 Always wear safety glasses when assembling this product. 9 Wear gloves when working with tubing to prevent cuts or abrasions. WARNING! Anchors must be used with alI shelters. DO NOT install the cover untiI the shelter is properly anchored to the ground. NOTE: proper anchoring and keeping the cover tight and free of snow and debris is the responsibility of the consumer. Damages caused by improper anchoring are not covered under warranty. WARNING! Keep all flame and heat sources away from the shelter. The fabric will burn if left in continuous contact with a flame. 8 DO NOT use open flames or cooking or heating devices inside or in close proximity to the product, including all types of stoves, gas heaters, gas lanterns, citronella torches, mosquito coils, etc. WARNING! In order to reduce risk of burning and avoid damage: 8 DO NOT cook, smoke, refuel or use any open flame devices in or around the shelter. 8 DO NOT store flammable liquids (gasoline, kerosene, propane, etc.) in the shelter. 8 DO NOT operate gas powered equipment in or around the shelter. 8 DO NOT use hard-edged tools or instruments, such as rakes or shovels, to remove snow. These can cause punctures to the cover. DANGER! DO NOT start the engine of any vehicle or machine inside a closed shelter. Ensure that there is adequate ventilation for starting engines and for any work with paints, cleaners, etc. 8 DO NOT use bleach, alkaline or harsh detergents for cleaning. Doing so will damage the material. Soap and warm water are recommended. 2. INTRODUCTION Made from durable 600D Oxford PU coated anti-scratch material to protect vehicle's paintwork. Rigid powder coated tubular frame with hinged opening for easy-access. Side vents allows increased ventilation while still keeping vehicle protected from the elements. Includes anchor points for fixing shelter to driveway/ground (fixings included). Padlock hasp for increased security when canopy is closed (two combination locks included). 3. SPECIFICATION Model No:............................................................STSXL Dimensions (L x W x H):............. 3800 x 2100 x 1900mm Nett Weight: ............................................................ 28kg Size: ............................................................................XL © Jack Sealey Limited Original Language Version STSXL Issue 2 17/01/2025 4. ASSEMBLY Check all parts and fixings before assembling the shelter. IMPORTANT: appropriate fixings must be used to secure the shelter. A heavy weight may be required on the support bar (D), in combination with suitable expansion screws. STEP 1 STEP 2 Position side frames (A) & (B) on the ground with the shortest tubes facing the front. STEP 3 Attach supports (E) onto the side frames (A) & (B), using the fixings provided. STEP 4 Connect angled bars (C) onto the side frames (A) & (B), leaving one angled bar (C) detached. Fix support bar (D) onto the side frames (A) & (B). Attach locking bar (J) onto the side frames (A) & (B) using the fixings provided. Slide rings (K) onto the frame. Leave in the unlocked position shown when assembling the shelter. Fold the frame backwards, making sure the fabric covers the frame. Let the bottom unconnected tubes pass through the fabric sleeves. STEP 5 STEP 6 Pass the last angled bar (C) through the fabric sleeve and connect it to the side frames (A & B). Wrap the frame with the velcro sewed on the fabric cover at the locations shown. © Jack Sealey Limited Original Language Version STSXL Issue 2 17/01/2025 5. MAINTENANCE 5.1. 9 8 8 5.2. 5.2.1. 5.2.2. CLEANING Clean with soap and warm water. DO NOT use bleach, alkaline or harsh detergents for cleaning. Doing so will damage the material. DO NOT use hard-edged tools or instruments, such as rakes or shovels, to remove snow. These can cause punctures to the cover. STORAGE Remove the supports (E) to enable the cover to lay flat on the ground. Tie all tubes together so the shelter can be moved for storage. ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. REGISTER YOUR PURCHASE HERE Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk www.sealey.co.uk © Jack Sealey Limited Original Language Version STSXL Issue 1 08/01/2025