Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-ness connectors. • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor with a hammer.
ELECTRICAL DI A SECTION B DRIVER INFORMATION SYSTEM C D CONTENTS E SERVICE INFORMATION ........................... 3 PRECAUTION .................................................... 3 Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ..................................................................3 Precaution Necessary for Steering Wheel Rotation After Battery Disconnect ....................................3 PREPARATION .................................................. 4 Commercial Service Tool .........................................4 COMBINATION METERS .................................. 5 Component Parts and Harness Connector Location ...........................................................................5 System Description ..................................................5 Arrangement of Combination Meter .........................8 Schematic ................................................................9 Wiring Diagram - METER - .................................... 10 Combination Meter Harness Connector Terminal Layout .................................................................... 12 Terminal and Reference Value for Combination Meter ...................................................................... 12 Self-Diagnosis Mode of Combination Meter ........... 13 CONSULT-III Function (METER/M&A) .................. 14 Trouble Diagnosis .................................................. 16 Symptom Chart ...................................................... 16 Power Supply and Ground Circuit Inspection ........ 16 Vehicle Speed Signal Inspection ............................ 17 Engine Speed Signal Inspection ............................ 18 Water Temperature Signal Inspection .................... 18 Fuel Level Sensor Signal Inspection ...................... 19 Fuel Gauge Fluctuates, Indicates Wrong Value, or Varies ..................................................................... 20 Fuel Gauge Does Not Move to Full-position .......... 21 DTC [U1000] CAN Communication Circuit ............ 21 Electrical Component Inspection ............................ 21 Removal and Installation ........................................ 22 DOUBLE METERS ............................................23 System Description ................................................ 23 Wiring Diagram - 2METER - ...................................24 F Terminal and Reference Value for Double Meter ....26 Terminal and Reference Value for Combination Meter ......................................................................26 G CONSULT-III Function (METER/M&A) ...................26 Trouble Diagnosis ...................................................26 Symptom Chart .......................................................27 Power Supply and Ground Circuit Inspection .........27 H Oil Pressure Sensor Inspection ..............................27 Removal and Installation ........................................29 I WARNING LAMPS ............................................31 Schematic ...............................................................31 Wiring Diagram - WARN - ......................................32 J Oil Pressure Warning Lamp Stays Off (Ignition Switch ON) .............................................................39 Oil Pressure Warning Lamp Does Not Turn Off (Oil Pressure Is Normal) .........................................41 DI Component Inspection ............................................42 CVT INDICATOR ...............................................43 L System Description .................................................43 Wiring Diagram - CVTIND - ....................................44 CVT Indicator Does Not Illuminate .........................46 M WARNING CHIME .............................................48 Component Parts and Harness Connector Loca- tion ..........................................................................48 N System Description .................................................49 Wiring Diagram - CHIME - ......................................52 Terminal and Reference Value for BCM .................53 CONSULT-III Function (BCM) ................................53 O Trouble Diagnosis ...................................................54 Combination Meter Buzzer Circuit Inspection ........55 Front Door Switch LH Signal Inspection .................56 P Key Switch Signal Inspection (Without Intelligent Key) ........................................................................57 Key Switch and Ignition Knob Switch Signal In- spection (With Intelligent Key, When Mechanical Key Is Used) ...........................................................58 Lighting Switch Signal Inspection ...........................60 Revision: October 2008 DI-1 2009 Sentra Seat Belt Buckle Switch LH Signal Inspection ....... 60 Parking Brake Switch Signal Inspection ................ 61 Electrical Component Inspection ........................... 62 Revision: October 2008 DI-2 2009 Sentra PRECAUTION < SERVICE INFORMATION > SERVICE INFORMATION A PRECAUTION Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B PRE-TENSIONER" INFOID:0000000004779261 The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain C types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D Information necessary to service the system safely is included in the SRS and SB section of this Service Man- ual. WARNING: E · To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. · Improper maintenance, including incorrect removal and installation of the SRS can lead to personal F injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. · Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har- ness connectors. · When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- H tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury. · When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I battery, and wait at least 3 minutes before performing any service. Precaution Necessary for Steering Wheel Rotation After Battery Disconnect J INFOID:0000000004750049 NOTE: · This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYSTEM). DI · Remove and install all control units after disconnecting both battery cables with the ignition knob in the LOCK position. · Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work. L If DTC is detected, perform trouble diagnosis according to self-diagnostic results. For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech- anism is adopted on the key cylinder. M For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and steering wheel rotation will become impossible. If steering wheel rotation is required when battery power is interrupted, follow the procedure below before starting the repair operation. N OPERATION PROCEDURE 1. Connect both battery cables. O NOTE: Supply power using jumper cables if battery is discharged. 2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ACC position. At this time, the steering lock will be released. P 3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be rotated. 4. Perform the necessary repair operation. 5. When the repair work is completed, return the ignition switch to the LOCK position before connecting the battery cables. (At this time, the steering lock mechanism will engage.) 6. Perform a self-diagnosis check of all control units using CONSULT-III. Revision: October 2008 DI-3 2009 Sentra < SERVICE INFORMATION > PREPARATION Commercial Service Tool Tool name Power tool PREPARATION INFOID:0000000004407611 Description Loosening bolts and nuts PBIC0191E Revision: October 2008 DI-4 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > COMBINATION METERS Component Parts and Harness Connector Location A INFOID:0000000004407612 B C D E F G H I LKIA0868E 1. Combination meter M24 2. ECM E16 4. Vehicle speed sensor F41 (without ABS or CVT) System Description 5. TCM F23 3. Fuel level sensor unit and fuel pump J (fuel level sensor) B48 (view with rear seat and inspection hole cover removed) (: Front) DI 6. ABS actuator and electric unit (control unit) E33 L INFOID:0000000004407613 UNIFIED METER CONTROL UNIT · Speedometer, odo/trip meter, tachometer, water temperature gauge and fuel gauge are controlled by the M unified meter control unit, which is built into the combination meter. · Warning and indicator lamps are controlled by signals drawn from the CAN communication system, BCM (body control module), and components connected directly to the combination meter. N · Odo/trip meter and CVT indicator segments can be checked in self-diagnosis mode. · Meters/gauges can be checked in self-diagnosis mode. POWER SUPPLY AND GROUND CIRCUIT O Power is supplied at all times · through 10A fuse [No. 19, located in the fuse block (J/B)] · to combination meter terminal 1. P With the ignition switch in the ON or START position, power is supplied · through 10A fuse [No. 14, located in the fuse block (J/B)] · to combination meter terminal 2. With the ignition switch in the ACC or ON position, power is supplied · through 10A fuse [No. 6, located in the fuse block (J/B)] · to combination meter terminal 23. Ground is supplied Revision: October 2008 DI-5 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > · to combination meter terminals 3, 21 and 22 · through grounds M57 and M61. SPEEDOMETER With ABS The ABS actuator and electric unit (control unit) provides a vehicle speed signal to the combination meter via CAN communication lines. WKIA5370E Without ABS or CVT The vehicle speed sensor provides a vehicle speed signal to the combination meter for speedometer indication. With CVT, Without ABS The TCM provides a vehicle speed signal to the combination meter via CAN communication lines. TACHOMETER The tachometer indicates engine speed in revolutions per minute (rpm). The ECM provides an engine speed signal to combination meter via CAN communication lines. SKIB6904E FUEL GAUGE The fuel gauge indicates the approximate fuel level in the fuel tank. The fuel gauge is regulated by the unified meter control unit and a variable resistor signal supplied · to combination meter terminal 4 · through fuel level sensor unit and fuel pump terminal 5 · through fuel level sensor unit and fuel pump terminal 2 · from combination meter terminal 8. WATER TEMPERATURE GAUGE The water temperature gauge indicates the engine coolant temperature. The ECM provides an engine coolant temperature signal to the combination meter via CAN communication lines. Revision: October 2008 DI-6 SKIB6905E 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > ODO/TRIP METER The vehicle speed signal and the memory signals from the meter memory circuit are processed by the combi- A nation meter and the mileage is displayed. How to Change the Display Refer to Owner's Manual for odo/trip meter operating instructions. B CAN COMMUNICATION SYSTEM DESCRIPTION Refer to LAN-6, "System Description". C D E F G H I J DI L M N O P Revision: October 2008 DI-7 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > Arrangement of Combination Meter INFOID:0000000004407614 Revision: October 2008 DI-8 WKIA5975E 2009 Sentra < SERVICE INFORMATION > Schematic COMBINATION METERS Revision: October 2008 DI-9 INFOID:0000000004407615 A B C D E F G H I J DI L M N O ABNWA0316GB P 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > Wiring Diagram - METER - INFOID:0000000004407616 Revision: October 2008 DI-10 AWMWA0093GB 2009 Sentra < SERVICE INFORMATION > COMBINATION METERS Revision: October 2008 DI-11 A B C D E F G H I J DI L M N O ABNWA0301GB P 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > Combination Meter Harness Connector Terminal Layout INFOID:0000000004407617 Terminal and Reference Value for Combination Meter WKIA5832E INFOID:0000000004407618 Ter- Condition mi- Wire nal color No. Item Ignition switch Operation or condition Reference value (V) (Approx.) 1 W Battery power supply OFF -- Battery voltage 2 P Ignition switch ON or START ON -- Battery voltage 3 B Ground (power) -- -- 0 4 B Fuel level sensor ground (-) ON -- 0 6 B Vehicle speed sensor ground (without ABS or CVT) ON -- 0 7 GR Vehicle speed signal (without ABS or CVT) Speedometer operated ON [When vehicle speed is approx. 20 km/h (12 MPH)] 240 Hz 8 LG Fuel level sensor signal (+) -- -- Refer to DI-21, "Electrical Component Inspection". 9 L CAN-H -- -- -- 10 P CAN-L -- -- -- 13 V Illumination control switch (LED) -- -- Refer to LT-96, "System Description". 16 SB Immobilizer/security indicator input OFF Security indicator ON Security indicator OFF 0 Battery voltage 18 G Seat belt buckle switch RH Unfastened (ON) ON Fastened (OFF) 0 Battery voltage 21 B Ground (illumination) -- -- 0 22 23 O Ignition switch ACC or ON ON -- Battery voltage 24 GR Parking Brake switch Parking brake applied ON Parking brake released 0 Battery voltage 25 V Brake fluid level switch Brake fluid level low ON Brake fluid level normal 0 Battery voltage 26 O Seat belt buckle switch LH Unfastened (ON) ON Fastened (OFF) 0 Battery voltage 28 R Washer fluid level switch (Canada models) Washer fluid level low ON Washer fluid level normal 0 Battery voltage 29 W O/D OFF switch O/D OFF switch pressed ON O/D OFF switch released 0 Battery voltage Revision: October 2008 DI-12 2009 Sentra < SERVICE INFORMATION > Ter- mi- Wire nal color Item No. COMBINATION METERS Ignition switch Condition Operation or condition Reference value (V) A (Approx.) NOTE: B Maximum voltage may be 12 V due to specifications (connected units). 31 O Vehicle speed signal output (8-pulse) Speedometer operated ON [When vehicle speed is approx. 40 km/h (25 MPH)] C D PKIC0643E 32 BR Generator Generator voltage low ON Generator voltage normal 0 E Battery voltage 33 V Illumination output to double meter -- -- Refer to LT-96, "System Description". F 37* LG Manual mode signal Manual mode switch ON ON Manual mode switch OFF 0 Battery voltage G 38* SB Not manual mode signal 39* W A/T steering shift up signal Manual mode switch ON ON Manual mode switch OFF · Manual mode switch ON ON · Steering shift up operation 0 Battery voltage H 0 Other than above Battery voltage I · Manual mode switch ON 40* Y A/T steering shift down signal ON · Steering shift down operation 0 *: With QR25DE Other than above Battery voltage J Self-Diagnosis Mode of Combination Meter INFOID:0000000004407619 DI SELF-DIAGNOSIS MODE FUNCTION · Self-diagnosis can check for continuity between the meter control circuit and the speedometer and tachome- ter. L · Self-diagnosis can check for odo/trip meter and CVT indicator segments. OPERATION PROCEDURE 1. Turn the ignition switch ON, and switch the odo/trip meter to "trip A" or "trip B". M NOTE: If the diagnosis function is activated with "trip A" displayed, the mileage on "trip A" will indicate "0000.0", but the actual trip mileage will be retained. (The same applies for "trip B".) N 2. Turn ignition switch OFF. 3. While pushing the odo/trip meter switch (1), turn the ignition switch ON. O 4. Confirm that the trip meter displays "0000.0". 5. Push the odo/trip meter switch at least 3 times. (Within 7 sec- onds after the ignition switch is turned ON.) P Revision: October 2008 DI-13 LKIA0870E 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > 6. All segments on the odo/trip meter illuminate. At this time, the unified meter control unit is turned to self-diagnosis mode. NOTE: · Check combination meter power supply and ground circuit when self-diagnosis mode of combination meter does not start. Replace combination meter if normal. Refer to IP-12, "Removal and Installation". · If any of the segments is not displayed, replace combination meter. Refer to IP-12, "Removal and Installation". 7. Each meter activates while pressing odo/trip meter switch. LKIA0871E LKIA0872E NOTE: If the speedometer or tachometer are not activated, replace combination meter. Refer to IP-12, "Removal and Installation". CONSULT-III Function (METER/M&A) INFOID:0000000004407620 CONSULT-III can display each diagnostic item using the diagnostic test modes shown following. METER diagnosis mode SELF-DIAG RESULTS DATA MONITOR CAN DIAG SUPPORT MNTR Description Displays combination meter self-diagnosis results. Displays combination meter input/output data in real time. The result of transmit/receive diagnosis of CAN communication can be read. SELF-DIAGNOSTIC RESULTS Display Item List CONSULT-III display Malfunction Reference page CAN COMM CIRC [U1000] Malfunction is detected in CAN communication lines. CAUTION: Even when there is no malfunction on CAN communication system, malfunction may be misinterpreted when battery has low voltage (when maintaining 7 - 8 V for about 2 seconds) or 10A fuse [No. 14, located in the fuse block (J/B)] is removed. DI-21 VEHICLE SPEED CIRC [B2205] Malfunction is detected when an erroneous speed signal is input. CAUTION: Even when there is no malfunction on speed signal system, malfunctions may be misinterpreted when battery has low voltage (when maintaining 7 - 8 V for about 2 seconds). DI-17 NOTE: "TIME" indicates the following. Revision: October 2008 DI-14 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > · 0: Indicates that a malfunction is detected at present. · 1-63: Indicates that a malfunction was detected in the past. (Displays number of ignition switch OFF ON A cycles after malfunction is detected. Self-diagnostic result is erased when "63" is exceeded.) DATA MONITOR B Display Item List Display item [Unit] SPEED METER [km/h] SPEED OUTPUT [km/h] TACHO METER [rpm] W TEMP METER [°C] FUEL METER [lit.] FUEL W/L [ON/OFF] C-ENG W/L [ON/OFF] AIR PRES W/L SEAT BELT W/L BUZZER [ON/OFF] DOOR W/L [ON/OFF] HI-BEAM IND [ON/OFF] TURN IND [ON/OFF] OIL W/L [ON/OFF] ABS W/L [ON/OFF] BRAKE W/L [ON/OFF] KEY G/Y W/L [ON/OFF] KEY R W/L [ON/OFF] KEY KNOB W/L [ON/OFF] O/D OFF SW [ON/OFF] P RANGE IND [ON/OFF] R RANGE IND [ON/OFF] N RANGE IND [ON/OFF] D RANGE IND [ON/OFF] L RANGE IND [ON/OFF] M RANGE SW [ON/OFF] NM RANGE SW [ON/OFF] AT-M IND [ON/OFF] AT-M GEAR [1 - 8] SPORT IND [ON/OFF] ST SFT UP SW [ON/OFF] ST SFT DWN SW [ON/OFF] CRUISE IND [ON/OFF] MAIN SIGNALS X X X X X X X X X X X X X X X X SELECTION FROM MENU Contents C X The value of vehicle speed signal, which is input from ABS actuator and electric unit (control unit). X The value of vehicle speed signal, which is transmitted to each D unit with CAN communication. X The value of engine speed signal, which is input from ECM. E X The value of engine coolant temperature signal, which is input from ECM. X The value, which processes a resistance signal from fuel gauge. F X Indicates [ON/OFF] condition of low-fuel warning lamp. X Indicates [ON/OFF] condition of malfunction indicator lamp (MIL). G X Indicates [ON/OFF] condition of low tire pressure warning lamp. X Indicates [ON/OFF] condition of seat belt warning lamp. H X Indicates [ON/OFF] condition of buzzer. X Indicates [ON/OFF] condition of door warning lamp. X Indicates [ON/OFF] condition of high beam indicator lamp. I X Indicates [ON/OFF] condition of turn indicator. X Indicates [ON/OFF] condition of oil pressure warning lamp. J X Indicates [ON/OFF] condition of ABS warning lamp. X Indicates [ON/OFF] condition of brake warning lamp.* X Indicates [ON/OFF] condition of KEY warning lamp (green). DI X Indicates [ON/OFF] condition of KEY warning lamp (red). X Indicates [ON/OFF] condition of LOCK warning lamp. L X Indicates [ON/OFF] condition of O/D OFF switch. X Indicates [ON/OFF] condition of CVT shift P range indicator. X Indicates [ON/OFF] condition of CVT shift R range indicator. M X Indicates [ON/OFF] condition of CVT shift N range indicator. X Indicates [ON/OFF] condition of CVT shift D range indicator. N X Indicates [ON/OFF] condition of CVT shift L range indicator. X Indicates [ON/OFF] condition of manual mode range switch. X Indicates [ON/OFF] condition of except manual mode range O switch. X Indicates [ON/OFF] condition of manual mode indicator. X Indicates [1 - 8] condition of manual mode gear position. P X Indicates [ON/OFF] condition of O/D OFF indicator. X Indicates [ON/OFF] condition of steering shift up switch. X Indicates [ON/OFF] condition of steering shift down switch. X Indicates [ON/OFF] condition of CRUISE indicator. Revision: October 2008 DI-15 2009 Sentra < SERVICE INFORMATION > COMBINATION METERS Display item [Unit] MAIN SIGNALS SELECTION FROM MENU Contents SET IND [ON/OFF] X Indicates [ON/OFF] condition of SET indicator. EPS W/L [ON/OFF] X Indicates [ON/OFF] condition of EPS warning lamp. *: The monitor will indicate "OFF" even though the brake warning lamp is on if either of the following conditions exist. · The parking brake is engaged · The brake fluid level is low Trouble Diagnosis INFOID:0000000004407621 HOW TO PERFORM TROUBLE DIAGNOSIS 1. Confirm the symptom or customer complaint. 2. Perform preliminary check. Refer to "PRELIMINARY CHECK". 3. According to the symptom chart, repair or replace the cause of the malfunction. Refer to DI-16, "Symptom Chart". 4. Does the meter operate normally? If so, GO TO 5. If not, GO TO 2. 5. Inspection End. PRELIMINARY CHECK 1.CHECK SELF-DIAGNOSIS OPERATION OF COMBINATION METER Perform self-diagnosis of combination meter. Refer to DI-13, "Self-Diagnosis Mode of Combination Meter". Does self-diagnosis mode operate? YES >> GO TO 2. NO >> Check power supply and ground circuit of combination meter. Refer to DI-16, "Power Supply and Ground Circuit Inspection". 2.CHECK COMBINATION METER (CONSULT-III) Select "METER/M&A" on CONSULT-III and perform self-diagnosis of combination meter. Refer to DI-14, "CONSULT-III Function (METER/M&A)". Self-diagnostic results content No malfunction detected>> Refer to DI-16, "Symptom Chart". Malfunction detected>> Refer to DI-14, "CONSULT-III Function (METER/M&A)". Symptom Chart INFOID:0000000004407622 Symptom Improper speedometer and odo/trip meter indication. Improper tachometer indication. Improper fuel gauge indication. Low-fuel warning lamp indication is irregular. Improper water temperature gauge indication. Improper CVT position indication. Possible cause Refer to DI-17, "Vehicle Speed Signal Inspection". Refer to DI-18, "Engine Speed Signal Inspection". Refer to DI-19, "Fuel Level Sensor Signal Inspection". Refer to DI-18, "Water Temperature Signal Inspection". Refer to DI-46, "CVT Indicator Does Not Illuminate". Power Supply and Ground Circuit Inspection 1.CHECK FUSE Check for blown combination meter fuses. INFOID:0000000004407623 Power source Battery Ignition switch ON or START Ignition switch ACC or ON Revision: October 2008 DI-16 Fuse No. 19 14 6 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > OK or NG OK >> GO TO 2. NG >> Be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-3. 2.CHECK POWER SUPPLY CIRCUIT Check voltage between combination meter harness connector terminals and ground. Terminals Ignition switch position (+) Combination meter connector Terminal () OFF ACC ON 1 Battery voltage Battery Battery volt- voltage age M24 2 Ground 0V 0V Battery voltage 23 0V Battery Battery volt- voltage age OK or NG OK >> GO TO 3. NG >> Repair harness or connector. 3.CHECK GROUND CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect combination meter connector. 3. Check continuity between combination meter harness connector terminals and ground. A B C D E WKIA5976E F G H I Combination meter connector Terminal Continuity 3 J Ground M24 21 Yes 22 OK or NG OK >> Replace combination meter. Refer to IP-12, "Removal and Installation". NG >> Repair harness or connector. DI LKIA0874E L Vehicle Speed Signal Inspection INFOID:0000000004407624 M Symptom: · Improper speedometer and odo/trip meter indication. · Display VEHICLE SPEED CIRC [B2205] at the result of self-diagnosis for combination meter. N WITH ABS 1.CHECK COMBINATION METER INPUT SIGNAL 1. Start engine and select "METER/M&A" on CONSULT-III. O 2. Using "SPEED METER" on "DATA MONITOR", compare the value of "DATA MONITOR" with speedome- ter pointer of combination meter. OK or NG P OK >> Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to BRC-18, "CONSULTIII Function (ABS)". NG >> Replace combination meter. Refer to IP-12, "Removal and Installation". WITHOUT ABS OR CVT 1.CHECK VEHICLE SPEED SENSOR CIRCUITS Revision: October 2008 DI-17 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > 1. Remove vehicle speed sensor. 2. Turn ignition switch ON. 3. Rotate vehicle speed sensor while checking voltage between combination meter harness connector M24 terminals 6 and 7. Terminals (+) () Connector Terminal Connector Terminal Voltage (Approx.) M24 7 M24 6 0.5 OK or NG OK >> Replace combination meter. Refer to IP-12, "Removal and Installation". NG >> GO TO 2. 2.CHECK VEHICLE SPEED SENSOR 1. Turn ignition switch OFF. 2. Disconnect vehicle speed sensor connector. 3. Check resistance between vehicle speed sensor terminals 1 and 2. LKIA0875E Terminals (+) () Component Terminal Component Terminal Resistance value (Approx.) Vehicle Vehicle speed 1 speed 2 sensor sensor 250 WKIA5833E OK or NG OK >> Check harness or connector between combination meter and vehicle speed sensor. NG >> Replace vehicle speed sensor. WITH CVT, WITHOUT ABS 1.CHECK COMBINATION METER INPUT SIGNAL 1. Start engine and select "METER/M&A" on CONSULT-III. 2. Using "SPEED METER" on "DATA MONITOR", compare the value of "DATA MONITOR" with speedome- ter pointer of combination meter. OK or NG OK >> Perform TCM self-diagnosis. Refer to CVT-47, "CONSULT-III Function (TRANSMISSION)". NG >> Replace combination meter. Refer to IP-12, "Removal and Installation". Engine Speed Signal Inspection INFOID:0000000004407625 Symptom: Improper tachometer indication. 1.CHECK COMBINATION METER INPUT SIGNAL 1. Start engine and select "METER/M&A" on CONSULT-III. 2. Using "TACHO METER" on "DATA MONITOR", compare the value of "DATA MONITOR" with tachometer pointer of combination meter. OK or NG OK >> Perform ECM self-diagnosis. Refer to EC-123, "CONSULT-III Function (ENGINE)". NG >> Replace combination meter. Refer to IP-12, "Removal and Installation". Water Temperature Signal Inspection INFOID:0000000004407626 Symptom: Improper water temperature gauge indication. 1.CHECK COMBINATION METER INPUT SIGNAL 1. Start engine and select "METER/M&A" on CONSULT-III. Revision: October 2008 DI-18 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > 2. Run the engine at different temperatures and compare water temperature with "W TEMP METER" of "DATA MONITOR". Indication should be as follows: A High: 130°C (266°F) Normal: 70 - 105°C (158 - 221°F) B Cold: Less than 50°C (122°F) OK or NG OK >> Perform ECM self-diagnosis. Refer to EC-123, "CONSULT-III Function (ENGINE)". C NG >> Replace combination meter. Refer to IP-12, "Removal and Installation". Fuel Level Sensor Signal Inspection INFOID:0000000004407627 D Symptom: · Improper fuel gauge indication. E · Low-fuel warning lamp indication is irregular. NOTE: The following symptoms do not indicate a malfunction. · Depending on vehicle position or driving circumstance, the fuel level in the tank shifts and the indication may F fluctuate. · If the vehicle is fueled with the ignition switch ON, the indication will update slowly. · If the vehicle is tilted when the ignition switch is turned ON, fuel in the tank may flow to one direction result- G ing in a change of reading. 1.CHECK COMBINATION METER INPUT SIGNAL H 1. Select "METER/M&A" on CONSULT-III. 2. Using "FUEL METER" on "DATA MONITOR", compare the value of "DATA MONITOR" with fuel gauge indication of combination meter. I Fuel gauge indication (approx. segments) Reference value of data monitor [lit.] Full (13) Approx. 55 J 3/4 (10) Approx. 38 1/2 (7) Approx. 25 1/4 (4) Approx. 13 DI Empty (0) Approx. 4 OK or NG L OK >> GO TO 2. NG >> Replace combination meter. Refer to IP-12, "Removal and Installation". 2.CHECK HARNESS CONNECTOR M 1. Turn ignition switch OFF. 2. Check combination meter and fuel level sensor unit terminals (meter-side and harness-side) for poor con- nection. N OK or NG OK >> GO TO 3. NG >> Repair or replace terminals or connectors. O 3.CHECK FUEL LEVEL SENSOR UNIT CIRCUIT P Revision: October 2008 DI-19 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > 1. Disconnect combination meter connector and fuel level sensor unit connector. 2. Check continuity between combination meter harness connector (A) and fuel level sensor unit and fuel pump harness connector (B). A Connector Terminal B Connector Terminal Continuity M24 8 B48 2 Yes 3. Check continuity between combination meter harness connector (A) and ground. WKIA5834E A Connector Terminal Ground Continuity M24 8 No OK or NG OK >> GO TO 4. NG >> Repair harness or connector. 4.CHECK FUEL LEVEL SENSOR UNIT GROUND CIRCUIT 1. Check continuity between combination meter harness connector (A) and fuel level sensor unit and fuel pump harness connector (B). A Connector Terminal B Connector Terminal Continuity M24 4 B48 5 Yes 2. Check continuity between combination meter harness connector (A) and ground. WKIA5835E A Connector Terminal Ground Continuity M24 4 No OK or NG OK >> GO TO 5. NG >> Repair harness or connector. 5.CHECK FUEL LEVEL SENSOR UNIT Check fuel level sensor unit. Refer to DI-21, "Electrical Component Inspection". OK or NG OK >> Check fuel level sensor unit installation, and check whether the float arm interferes or binds with any of the internal components in the fuel tank. Repair or replace malfunctioning part, if necessary. NG >> Replace fuel level sensor unit. Fuel Gauge Fluctuates, Indicates Wrong Value, or Varies INFOID:0000000004407628 1.CHECK FUEL GAUGE FLUCTUATION Test drive vehicle to see if gauge fluctuates only during driving or at the instant of stopping. Does the indication value vary only during driving or at the at the instant of stopping? YES >> The gauge fluctuation may be caused by fuel level change in the fuel tank. Condition is normal. NO >> Ask the customer about the situation when the symptom occurs in detail, and perform the trouble diagnosis. Revision: October 2008 DI-20 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > Fuel Gauge Does Not Move to Full-position 1.OBSERVE FUEL GAUGE INFOID:0000000004407629 A Does it take a long time for the indication to move to FULL position? YES or NO B YES >> GO TO 2. NO >> GO TO 3. 2.IDENTIFY FUELING CONDITION C Was the vehicle fueled with the ignition switch ON? YES or NO D YES >> Be sure to fuel the vehicle with the ignition switch OFF. Otherwise, it will take a long time to move to FULL position because of the characteristic of the fuel gauge. NO >> GO TO 3. E 3.OBSERVE VEHICLE POSITION Is the vehicle parked on an incline? F YES or NO YES >> Check the fuel level indication with vehicle on a level surface. NO >> GO TO 4. 4.OBSERVE FUEL GAUGE POINTER G During driving, does the fuel gauge indication move gradually toward EMPTY position? YES or NO YES >> Check the components. Refer to DI-21, "Electrical Component Inspection". NO >> The float arm may interfere or bind with any of the components in the fuel tank. DTC [U1000] CAN Communication Circuit H I INFOID:0000000004407630 Symptom: Display CAN COMM CIRC [U1000] at the result of self-diagnosis for combination meter. 1.CHECK CAN COMMUNICATION J Select "SELF-DIAG RESULTS" mode for "METER/M&A" with CONSULT-III. DI >> Go to "CAN SYSTEM". Refer to LAN-44, "Diagnosis Procedure". Electrical Component Inspection INFOID:0000000004407631 L FUEL LEVEL SENSOR UNIT CHECK For removal, refer to FL-5, "Removal and Installation". M Check Fuel Level Sensor Unit and Fuel Pump Check resistance between terminals 2 and 5. N Resistance Terminals Float position mm (in) value () (Approx.) O 1* Full 145.9 (5.74) 5 2 5 2* Empty 14 (0.55) 81.5 1* and 2*: When float rod is in contact with stopper. P Check Fuel Level Sensor Unit and Fuel Pump Harness WKIA5456E Revision: October 2008 DI-21 2009 Sentra COMBINATION METERS < SERVICE INFORMATION > Check continuity at the following terminals. Terminal Continuity 2 - Signal terminal (A) Yes 5 - Ground terminal (B) · If the results of check are NG, replace fuel pump assembly. If the results of check are OK, replace fuel level sensor unit. Removal and Installation COMBINATION METER Refer to IP-12, "Removal and Installation". WKIA5457E INFOID:0000000004407632 Revision: October 2008 DI-22 2009 Sentra < SERVICE INFORMATION > DOUBLE METERS System Description DOUBLE METERS DOUBLE METER Oil pressure gauge and G-force gauge are controlled by the double meter. A INFOID:0000000004407633 B C D E WKIA5977E Oil Pressure Warning Lamp The oil pressure warning lamp is controlled by the double meter. When the oil pressure is less than 4.52 psi F (0.318 kg/cm2), the double meter sends a ground signal to the IPDM E/R. The IPDM E/R then sends a signal to the combination meter via CAN communication and the oil pressure warning lamp is turned on. When the oil pressure is greater than 6.5 psi (0.457 kg/cm2) the warning lamp turns off. G POWER SUPPLY AND GROUND CIRCUIT Power is supplied at all times H · through 10A fuse [No. 19, located in the fuse block (J/B)] · to double meter terminal 7 and · to combination meter terminal 1. With the ignition switch in the ON or START position, power is supplied I · through 10A fuse [No. 14, located in the fuse block (J/B)] · to double meter terminal 8 and · to combination meter terminal 2. J With the ignition switch in the ACC or ON position, power is supplied · through 10A fuse [No. 6, located in the fuse block (J/B)] · to combination meter terminal 23. Ground is supplied DI · to double meter terminals 9 and 10 and · to combination meter terminals 3 and 21 · through body grounds M57 and M61. L OIL PRESSURE GAUGE The oil pressure gauge indicates engine oil pressure. With the ignition switch in the ON or START position, power is supplied M · through double meter terminal 3 · to oil pressure sensor terminal 3. Ground is supplied · through double meter terminal 5 N · to oil pressure sensor terminal 1. Double meter receives oil pressure signal from oil pressure sensor · through oil pressure sensor terminal 2 O · to double meter terminal 4. G-FORCE GAUGE The G-force gauge indicates the longitudinal acceleration and deceleration G-forces while driving. The indica- P tion is based on a calculation using the speed input supplied by the combination meter via CAN communication. The gauge does not indicate cornering G-forces. Revision: October 2008 DI-23 2009 Sentra < SERVICE INFORMATION > Wiring Diagram - 2METER - DOUBLE METERS INFOID:0000000004407634 Revision: October 2008 DI-24 AWMWA0094GB 2009 Sentra < SERVICE INFORMATION > DOUBLE METERS Revision: October 2008 DI-25 A B C D E F G H I J DI L M N O ABNWA0271GB P 2009 Sentra DOUBLE METERS < SERVICE INFORMATION > Terminal and Reference Value for Double Meter INFOID:0000000004407635 Terminal No. 1 2 3 4 5 6 7 8 9 10 11 12 Wire color L P Y G R SB W P Item CAN-H CAN-L Oil pressure sensor power supply Oil pressure sensor signal Oil pressure sensor ground Oil pressure warn out Battery power supply Ignition switch ON or START Ignition switch -- -- ON ON ON ON OFF ON Condition Operation or condition -- -- -- When ignition switch is in the ON position. (Engine stopped) Engine running. [When the oil pressure is 60 psi (4.22 kg/cm2)] -- Engine oil pressure is below 4.52 psi (0.318 kg/cm2) Engine oil pressure is above 6.5 psi (0.457 kg/cm2) -- -- Voltage (V) (Approx.) -- -- 5.5 0.5 2.5 0 0.5 Battery voltage Battery voltage Battery voltage B Ground ON -- 0 R Illumination control -- -- Refer to LT-96, "System Description". V Illumination control -- -- Refer to LT-96, "System Description". Terminal and Reference Value for Combination Meter INFOID:0000000004407636 Refer to DI-12, "Terminal and Reference Value for Combination Meter". CONSULT-III Function (METER/M&A) INFOID:0000000004407637 Refer to DI-14, "CONSULT-III Function (METER/M&A)". Trouble Diagnosis INFOID:0000000004407638 HOW TO PERFORM TROUBLE DIAGNOSIS 1. Confirm the symptom or customer complaint. 2. Perform preliminary check. Refer to "PRELIMINARY CHECK". 3. According to the symptom chart, repair or replace the cause of the symptom. Refer to DI-27, "Symptom Chart". 4. Does the double meter operate normally? If so, GO TO 5. If not, GO TO 2. 5. Inspection End. PRELIMINARY CHECK 1.CHECK COMBINATION METER (CONSULT-III) Select "METER/M&A" on CONSULT-III and perform self-diagnosis of combination meter. Refer to DI-14, "CONSULT-III Function (METER/M&A)". Self-diagnostic results content No malfunction detected>>Refer to DI-27, "Symptom Chart". Malfunction detected>>Refer to DI-14, "CONSULT-III Function (METER/M&A)". Revision: October 2008 DI-26 2009 Sentra < SERVICE INFORMATION > Symptom Chart DOUBLE METERS INFOID:0000000004407639 A Symptom Improper oil pressure gauge indication. Improper G-force gauge indication. Double meter is inoperative. Possible cause Refer to DI-27, "Oil Pressure Sensor Inspection". B Replace double meter. Refer to DI-29, "Removal and Installation". · Refer to DI-27, "Power Supply and Ground Circuit Inspection". · Replace double meter. Refer to DI-29, "Removal and Installa- C tion". Power Supply and Ground Circuit Inspection 1.CHECK FUSES INFOID:0000000004407640 D Check for blown double meter fuses. E Power source Fuse No. Battery Ignition switch ON or START 19 F 14 OK or NG OK >> GO TO 2. G NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG- 3. 2.CHECK POWER SUPPLY CIRCUIT H 1. Disconnect the double meter connector. 2. Check voltage between double meter harness connector termi- nals and ground. I Terminals Ignition switch position (+) () Connector Terminal OFF ON START 7 Battery voltage Battery voltage Battery voltage M89 Ground 8 0V Battery voltage Battery voltage OK or NG OK >> GO TO 3. NG >> Check harness for open between double meter and fuse. 3.CHECK GROUND CIRCUIT 1. Turn ignition switch OFF. 2. Check continuity between double meter harness connector M89 terminals 9, 10 and ground. Continuity should exist. OK or NG OK >> Inspection End. NG >> Check harness or connector. J DI WKIA5978E L M N O P Oil Pressure Sensor Inspection 1.CHECK OIL PRESSURE SENSOR SIGNAL Revision: October 2008 DI-27 WKIA5979E INFOID:0000000004407641 2009 Sentra DOUBLE METERS < SERVICE INFORMATION > 1. Turn ignition switch ON. 2. Check voltage between double meter harness connector M89 terminal 4 and ground. Terminals (+) () Connector Terminal Condition Voltage (Approx.) When ignition switch is in ON position. (Engine stopped.) 0.5V M89 4 Ground Engine running. [When the oil pressure is 60 psi (4.22 kg/ 2.5V cm2)] OK or NG OK >> Replace double meter. Refer to DI-29, "Removal and Installation". NG >> GO TO 2. 2.CHECK OIL PRESSURE SENSOR POWER SUPPLY Check voltage between double meter harness connector M89 terminal 3 and ground. Approx. 5.5V OK or NG OK >> GO TO 3. NG >> Replace double meter. Refer to DI-29, "Removal and Installation". 3.CHECK OIL PRESSURE SENSOR POWER SUPPLY CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect double meter and oil pressure sensor connectors. 3. Check continuity between double meter harness connector M89 (A) terminal 3 and oil pressure sensor harness connector F32 (B) terminal 3. Continuity should exist. 4. Check continuity between double meter harness connector M89 (A) terminal 3 and ground. Continuity should not exist. OK or NG OK >> GO TO 4. NG >> Repair harness or connector between double meter and oil pressure sensor. 4.CHECK OIL PRESSURE SENSOR SIGNAL CIRCUIT WKIA5980E WKIA5981E WKIA5982E Revision: October 2008 DI-28 2009 Sentra DOUBLE METERS < SERVICE INFORMATION > 1. Check continuity between double meter harness connector M89 (B) terminal 4 and oil pressure sensor harness connector F32 (A) terminal 2. Continuity should exist. 2. Check continuity between double meter harness connector M89 (B) terminal 4 and ground. Continuity should not exist. OK or NG OK >> GO TO 5. NG >> Repair harness or connector between double meter and oil pressure sensor. 5.CHECK OIL PRESSURE SENSOR GROUND CIRCUIT Check continuity between double meter harness connector M89 (A) terminal 5 and oil pressure sensor harness connector F32 (B) terminal 1. Continuity should exist. OK or NG OK >> Replace oil pressure sensor. NG >> Repair harness or connector between double meter and oil pressure sensor. Removal and Installation COMPONENTS A B C WKIA5983E D E F G H WKIA5984E INFOID:0000000004407642 I J DI L M N O P 1. Double meter Clip Revision: October 2008 2. Upper housing Pawl DI-29 LKIA0922E 3. Double meter finisher 2009 Sentra DOUBLE METERS < SERVICE INFORMATION > REMOVAL 1. Carefully remove the double meter assembly (1) using suitable tool. CAUTION: Wrap suitable tool with clean shop cloth to prevent damage to the instrument panel. 2. Disconnect the double meter assembly connector (1) and remove the double meter assembly (2). INSTALLATION Installation is in the reverse order of removal. LKIA0923E LKIA0924E Revision: October 2008 DI-30 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Schematic WARNING LAMPS Revision: October 2008 DI-31 A INFOID:0000000004407643 B C D E F G H I J DI L M N O P AWMWA0095GB 2009 Sentra < SERVICE INFORMATION > Wiring Diagram - WARN - WARNING LAMPS INFOID:0000000004407644 Revision: October 2008 DI-32 AWMWA0096GB 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Revision: October 2008 DI-33 A B C D E F G H I J DI L M N O WKWA5764E P 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Revision: October 2008 DI-34 ABNWA0272GB 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Revision: October 2008 DI-35 A B C D E F G H I J DI L M N O WKWA5857E P 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Revision: October 2008 DI-36 WKWA5423E 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Revision: October 2008 DI-37 A B C D E F G H I J DI L M N O WKWA5424E P 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Revision: October 2008 DI-38 AWMWA0098GB 2009 Sentra < SERVICE INFORMATION > WARNING LAMPS Oil Pressure Warning Lamp Stays Off (Ignition Switch ON) 1.CHECK OIL PRESSURE WARNING LAMP OPERATION Activate IPDM E/R auto active test. Refer to PG-20, "Auto Active Test". Does oil pressure warning lamp blink? YES >> GO TO 2. NO >> GO TO 5. Revision: October 2008 DI-39 A B C D E F G H I J DI L M N O ABNWA0273GB INFOID:0000000004407645 P 2009 Sentra WARNING LAMPS < SERVICE INFORMATION > 2.CHECK IPDM E/R INPUT SIGNAL 1. Turn ignition switch ON. 2. Check voltage between IPDM E/R harness connector and ground. Terminals (+) IPDM E/R connector Terminal () Condition Voltage (Approx.) E46 37 Ground Engine stopped 0V OK or NG OK >> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R". NG >> GO TO 3. 3.CHECK OIL PRESSURE CIRCUIT WKIA5458E 1. Disconnect IPDM E/R connector and oil pressure switch connector (with MR20DE) or double meter connector (with QR25DE). 2. Check continuity between IPDM E/R harness connector E46 (A) terminal 37 and oil pressure switch harness connector F32 (B) terminal 1 (with MR20DE) or double meter connector M89 (C) terminal 6 (with QR25DE). With MR20DE 37 - 1 : Continuity should exist With QR25DE 37 - 6 : Continuity should exist WKIA5985E OK or NG OK >> With MR20DE, GO TO 4. With QR25DE, refer to DI-27, "Oil Pressure Sensor Inspection". NG >> Repair harness or connector. 4.CHECK OIL PRESSURE SWITCH Check oil pressure switch. Refer to DI-42, "Component Inspection". OK or NG OK >> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R". NG >> Replace oil pressure switch. 5.CHECK CAN COMMUNICATION Select "METER/M&A" on CONSULT-III, and perform self-diagnosis of combination meter. Self-diagnostic results content No malfunction detected>> GO TO 6. Malfunction detected>> Check applicable parts, and repair or replace as necessary. 6.CHECK COMBINATION METER INPUT SIGNAL Select "METER/M&A" on CONSULT-III. Operate ignition switch with "OIL W/L" of "DATA MONITOR" and check operation status. "OIL W/L" When ignition switch is in ON position (Engine stopped.) When engine running : ON : OFF OK or NG OK >> Replace combination meter. Refer to IP-12, "Removal and Installation". Revision: October 2008 DI-40 2009 Sentra WARNING LAMPS < SERVICE INFORMATION > NG >> GO TO 7. 7.CHECK BCM INPUT SIGNAL A Select "BCM" on CONSULT-III. Then select "SIGNAL BUFFER". Operate ignition switch with "OIL PRESS SW" of "DATA MONITOR" and check operation status. B "OIL PRESS SW" When ignition switch is in ON : ON position (Engine stopped.) C When engine running : OFF OK or NG OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM". NG >> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R". Oil Pressure Warning Lamp Does Not Turn Off (Oil Pressure Is Normal) D E INFOID:0000000004407646 NOTE: For oil pressure inspection, refer to LU-5, "Inspection" (MR20DE) or LU-16, "Inspection" (QR25DE). F 1.CHECK OIL PRESSURE WARNING LAMP OPERATION Activate IPDM E/R auto active test. Refer to PG-20, "Auto Active Test". G Does oil pressure warning lamp blink? YES >> GO TO 2. NO >> GO TO 5. 2.CHECK IPDM E/R OUTPUT SIGNAL H 1. Turn ignition switch OFF. 2. Disconnect oil pressure switch connector (with MR20DE) or double meter connector (with QR25DE). I 3. Turn ignition switch ON. 4. Check voltage between oil pressure switch harness connector F32 (A) terminal 1 (with MR20DE) or double meter connector J M89 (B) terminal 6 (with QR25DE) and ground. With MR20DE DI 1 - ground : Battery voltage With QR25DE L 6 - ground : Battery voltage OK or NG WKIA5986E OK >> With MR20DE, GO TO 3. With QR25DE, refer to DI-27, "Oil Pressure Sensor Inspection". M NG >> GO TO 4. 3.CHECK OIL PRESSURE SWITCH N 1. Turn ignition switch OFF. 2. Check oil pressure switch. Refer to DI-42, "Component Inspection". OK or NG O OK >> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R". NG >> Replace oil pressure switch. 4.CHECK OIL PRESSURE CIRCUIT P 1. Disconnect IPDM E/R connector and oil pressure switch connector (with MR20DE) or double meter connector (with QR25DE). Revision: October 2008 DI-41 2009 Sentra WARNING LAMPS < SERVICE INFORMATION > 2. Check continuity between IPDM E/R harness connector E46 (A) terminal 37 and oil pressure switch harness connector F32 (B) terminal 1 (with MR20DE) or double meter connector M89 (C) terminal 6 (with QR25DE). With MR20DE 37 - 1 : Continuity should exist With QR25DE 37 - 6 : Continuity should exist OK or NG OK >> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R". NG >> Repair harness or connector. 5.CHECK BCM INPUT SIGNAL WKIA5985E Select "BCM" on CONSULT-III. Then select "SIGNAL BUFFER". Operate ignition switch with "OIL PRESS SW" of "DATA MONITOR" and check operation status. "OIL PRESS SW" When ignition switch is in ON position (Engine stopped.) When engine running : ON : OFF OK or NG OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM". NG >> Replace IPDM E/R. Refer to PG-27, "Removal and Installation of IPDM E/R". Component Inspection INFOID:0000000004407647 OIL PRESSURE SWITCH Check continuity between oil pressure switch and ground. Condition Engine stopped Engine running Oil pressure [kPa (bar, kg/cm2, psi)] Less than 29 (0.3, 0.3, 4) More than 29 (0.3, 0.3, 4) Continuity Yes No ELF0044D Revision: October 2008 DI-42 2009 Sentra < SERVICE INFORMATION > CVT INDICATOR System Description CVT INDICATOR A INFOID:0000000004407648 The TCM receives CVT indicator signals from the park/neutral position (PNP) switch. The TCM then sends B CVT position indicator signals to the combination meter via CAN communication lines. The combination meter indicates the received shift position. C D E WKIA5987E F G H I J DI L M N O P Revision: October 2008 DI-43 2009 Sentra < SERVICE INFORMATION > Wiring Diagram - CVTIND - CVT INDICATOR INFOID:0000000004407649 Revision: October 2008 DI-44 AWMWA0100GB 2009 Sentra < SERVICE INFORMATION > CVT INDICATOR Revision: October 2008 DI-45 A B C D E F G H I J DI L M N O AWMWA0101GB P 2009 Sentra < SERVICE INFORMATION > CVT INDICATOR CVT Indicator Does Not Illuminate 1.CHECK SEGMENT OF CVT INDICATOR Revision: October 2008 DI-46 AWMWA0102GB INFOID:0000000004407650 2009 Sentra CVT INDICATOR < SERVICE INFORMATION > Perform self-diagnosis of combination meter. Refer to DI-13, "Self- Diagnosis Mode of Combination Meter". A Are all segments displayed? YES >> GO TO 2. NO >> Replace combination meter. Refer to IP-12, "Removal B and Installation". C 2.CHECK COMBINATION METER (CONSULT-III) LKIA0871E D 1. Connect CONSULT-III. 2. Select "METER/M&A" on CONSULT-III, and perform self-diagnosis of combination meter. Refer to DI-14, "CONSULT-III Function (METER/M&A)". E Self-diagnostic results content No malfunction detected>> GO TO 3. Malfunction detected>> Check applicable parts, and repair or replace as necessary. F 3.CHECK COMBINATION METER INPUT SIGNAL Use "DATA MONITOR" of "METER/M&A" on CONSULT-III. Confirm each indication on the monitor while oper- G ating the CVT selector lever. CONSULT-III display Switch operation Operation status H P range position ON P RANGE IND Except for P range position OFF I R range position ON R RANGE IND Except for R range position OFF N range position ON J N RANGE IND Except for N range position OFF D range position ON D RANGE IND DI Except for D range position OFF L range position ON L RANGE IND Except for L range position OFF L OK or NG OK >> Replace combination meter. Refer to IP-12, "Removal and Installation". NG >> GO TO 4. M 4.CHECK SELF-DIAGNOSIS RESULTS OF TCM Perform self-diagnosis of TCM. Refer to CVT-47, "CONSULT-III Function (TRANSMISSION)". N OK or NG OK >> Check TCM input/output signal. Repair or replace malfunctioning part, if necessary. Refer to CVT- 45, "TCM Input/Output Signal Reference Value". NG >> Check applicable part, and repair or replace as necessary. O P Revision: October 2008 DI-47 2009 Sentra < SERVICE INFORMATION > WARNING CHIME WARNING CHIME Component Parts and Harness Connector Location INFOID:0000000004407651 Revision: October 2008 DI-48 LKIA0877E 2009 Sentra < SERVICE INFORMATION > WARNING CHIME 1. Combination meter M24 2. Combination switch M28 3. Key switch and ignition knob switch A M49 (with Intelligent Key) 4. Key switch M50 (without Intelligent 5. Front door switch LH B21 6. Seat belt buckle switch LH B16 Key) 7. BCM M18, M19, M20 (view with in- 8. Intelligent Key unit M42 (view with 9. Parking brake switch B24 B strument panel removed) instrument panel removed) System Description INFOID:0000000004407652 C · Buzzer for warning chime system is installed in the combination meter. · The buzzer sounds when combination meter receives buzzer output signal with CAN communication line. D POWER SUPPLY AND GROUND CIRCUIT Power is supplied at all times · through 50A fusible link (letter j, located in the fuse and fusible link box) E · to BCM terminal 70, · through 10A fuse [No. 21, located in the fuse block (J/B)] · to BCM terminal 57, · through 10A fuse [No. 19, located in the fuse block (J/B)] F · to combination meter terminal 1 and · to key switch (without Intelligent Key) terminal 2, · through 10A fuse [No. 9, located in the fuse block (J/B)] G · to key switch and ignition knob switch (with Intelligent Key) terminals 2 and 4. With ignition switch in the ON or START position, power is supplied · through 10A fuse [No. 12, located in the fuse block (J/B)] · to BCM terminal 38, H · through 10A fuse [No. 14, located in the fuse block (J/B)] · to combination meter terminal 2. With ignition switch in the ACC or ON position, power is supplied I · through 10A fuse [No. 6, located in the fuse block (J/B)] · to combination meter terminal 23. Ground is supplied · to BCM terminal 67 and J · to combination meter terminals 3 and 21 · through grounds M57 and M61. IGNITION KEY WARNING CHIME (WITHOUT INTELLIGENT KEY) DI With the key inserted into the key switch, and the ignition switch in the OFF or ACC position, when driver's door is opened, the warning chime will sound. · BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with L CAN communication line. · When combination meter receives key warning signal, it sounds warning chime. M N O IGNITION KEY WARNING CHIME (WITH INTELLIGENT KEY) WKIA5463E P When Mechanical Key Is Used With the key inserted into the key switch, and the ignition switch in the LOCK or ACC position, when driver's door is opened, the warning chime will sound. · BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with CAN communication line. Revision: October 2008 DI-49 2009 Sentra WARNING CHIME < SERVICE INFORMATION > · When combination meter receives key warning signal, it sounds warning chime. WKIA5836E When Intelligent Key Is Carried With The Driver Refer to BL-72, "System Description". LIGHT WARNING CHIME The warning chime sounds, when driver's door is opened (door switch ON) with lighting switch ON and the ignition switch is in any position other than ON or START. NOTE: BCM detected lighting switch in the 1st or 2nd position, refer to LT-59, "Combination Switch Reading Function". · BCM detects headlamps are illuminated, and sends light warning signal to combination meter with CAN communication lines. · When the combination meter receives light warning signal, it sounds warning chime. WKIA5465E SEAT BELT WARNING CHIME With the ignition switch turned ON and driver's seat belt unfastened, the seat belt warning chime will sound for approximately 6 seconds. · The combination meter reads an ON/OFF signal from the seat belt buckle switch LH, and transmits the seat belt buckle switch signal to the BCM with CAN communication. · The BCM detects the ignition switch turned ON and seat belt buckle switch LH ON. And then, transmits the buzzer output signal (seat belt warning chime) to the combination meter with CAN communication. · When the combination meter receives the buzzer output signal (seat belt warning chime), it sounds the buzzer. LKIA0878E PARKING BRAKE WARNING CHIME The parking brake warning chime sounds when the parking brake is applied and vehicle speed reaches approximately 2 km/h (1 MPH). · The combination meter receives a parking brake applied signal from the parking brake switch. Revision: October 2008 DI-50 2009 Sentra WARNING CHIME < SERVICE INFORMATION > · When the combination meter receives a vehicle speed signal from the ABS actuator and electric unit (control unit) (with ABS), vehicle speed sensor (without ABS or CVT) or the TCM (with CVT, without ABS), it sounds A the buzzer. B C D LKIA0906E E F G H I J DI L M N O P Revision: October 2008 DI-51 2009 Sentra < SERVICE INFORMATION > Wiring Diagram - CHIME - WARNING CHIME INFOID:0000000004407653 Revision: October 2008 DI-52 WKWA5429E 2009 Sentra < SERVICE INFORMATION > WARNING CHIME A B C D E F G H I J DI L M N O Terminal and Reference Value for BCM ABNWA0274GB INFOID:0000000004407654 P Refer to BCS-11, "Terminal and Reference Value for BCM". CONSULT-III Function (BCM) INFOID:0000000004407655 CONSULT-III can display each diagnostic item using the diagnostic test modes shown following. Revision: October 2008 DI-53 2009 Sentra < SERVICE INFORMATION > WARNING CHIME BCM diagnostic test item Diagnostic mode Description WORK SUPPORT Supports inspections and adjustments. Commands are transmitted to the BCM for setting the status suitable for required operation, input/output signals are received from the BCM and received data is displayed. DATA MONITOR Displays BCM input/output data in real time. Inspection by part ACTIVE TEST SELF-DIAG RESULTS Operation of electrical loads can be checked by sending drive signal to them. Displays BCM self-diagnosis results. CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read. ECU PART NUMBER BCM part number can be read. CONFIGURATION Performs BCM configuration read/write functions. DATA MONITOR Display Item List Monitored item IGN ON SW KEY ON SW DOOR SW-DR LIGHT SW 1ST BUCKLE SW ACTIVE TEST Display Item List ALL SIGNALS X X X X X SELECTION FROM MENU X X X X X Contents Indicates [ON/OFF] condition of ignition switch. Indicates [ON/OFF] condition of key switch. Indicates [ON/OFF] condition of front door switch LH. Indicates [ON/OFF] condition of lighting switch. Indicates [ON/OFF] condition of seat belt buckle switch LH. Test item IGN KEY WARN ALM LIGHT WARN ALM SEAT BELT WARN TEST SELF-DIAG RESULTS Display Item List Malfunction is detected when... This test is able to check key warning chime operation. This test is able to check light warning chime operation. This test is able to check seat belt warning chime operation. Display item [Code] Malfunction is detected when... CAN communication [U1000] Malfunction is detected in CAN communication. NOTE: If "CAN communication [U1000]" is indicated, go to "LAN system". Refer to LAN-47, "Diagnosis Procedure". Trouble Diagnosis INFOID:0000000004407656 HOW TO PERFORM TROUBLE DIAGNOSIS 1. Confirm the symptom and customer complaint. 2. Understand the outline of system. Refer to DI-49, "System Description". 3. Perform the preliminary inspection. Refer to "PRELIMINARY INSPECTION". 4. According to symptom chart, repair or replace the cause of the malfunction. Refer to "SYMPTOM CHART". 5. Does warning chime system operate normally? If it operates normally, GO TO 6. If not, GO TO 4. 6. Inspection End. PRELIMINARY INSPECTION Revision: October 2008 DI-54 2009 Sentra WARNING CHIME < SERVICE INFORMATION > 1.CHECK BCM A Perform self-diagnosis of BCM. Refer to DI-53, "CONSULT-III Function (BCM)". Self-diagnostic results content No malfunction detected>> GO TO 2. B Malfunction detected>> Check applicable parts, and repair or replace corresponding parts. 2.CHECK COMBINATION METER Perform self-diagnosis of combination meter. Refer to DI-14, "CONSULT-III Function (METER/M&A)". C Self-diagnostic results content No malfunction detected>> Inspection End. Malfunction detected>> Check applicable parts, and repair or replace corresponding parts. D SYMPTOM CHART Symptom E Diagnoses/Service procedure All warning chime systems do not activate. Perform DI-55, "Combination Meter Buzzer Circuit Inspection". If above check is OK, replace BCM. Refer to BCS-17, "Removal F and Installation of BCM". Without Intelligent Key. Perform DI-57, "Key Switch Signal Inspection (Without Intelligent Key)". If above check is OK, replace BCM. Refer to BCS-17, "Removal G and Installation of BCM". Key warning chime Perform DI-58, "Key Switch and Ignition Knob Switch Signal In- does not activate. With Intelligent Key, when mechanical key spection (With Intelligent Key, When Mechanical Key Is Used)". H is used. If above check is OK, replace BCM. Refer to BCS-17, "Removal and Installation of BCM". With Intelligent Key, when Intelligent Key is carried with the driver. Refer to BL-99, "Trouble Diagnosis Symptom Chart". I Light warning chime does not activate. Perform DI-60, "Lighting Switch Signal Inspection". If above check is OK, replace BCM. Refer to BCS-17, "Removal and Installation of BCM". J Seat belt warning chime does not activate Perform DI-60, "Lighting Switch Signal Inspection". If above check is OK, replace BCM. Refer to BCS-17, "Removal and Installation of BCM". DI Perform the following inspections Parking brake warning chime does not activate · DI-61, "Parking Brake Switch Signal Inspection" · DI-17, "Vehicle Speed Signal Inspection" L Combination Meter Buzzer Circuit Inspection INFOID:0000000004407657 1.CHECK CHIME OPERATION M 1. Select "BUZZER" of "BCM" on CONSULT-III. 2. Perform "LIGHT WARN ALM" or "IGN KEY WARN ALM" of "ACTIVE TEST". N Does chime sound? YES >> Combination meter buzzer circuit is OK. Return to DI-54, "Trouble Diagnosis". NO >> GO TO 2. O 2.CHECK COMBINATION METER INPUT SIGNAL 1. Select "METER/M&A" on CONSULT-III. 2. Turn on hazard switch or lighting switch while monitoring "BUZZER" of "DATA MONITOR" and check P operation status. "BUZZER" While hazard switch or lighting switch is ON Except above : ON and OFF repeatedly : OFF Revision: October 2008 DI-55 2009 Sentra WARNING CHIME < SERVICE INFORMATION > OK or NG OK >> Check battery power supply circuit of combination meter. If OK, replace combination meter. Refer to IP-12, "Removal and Installation". NG >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM". Front Door Switch LH Signal Inspection INFOID:0000000004407658 1.CHECK BCM INPUT SIGNAL With CONSULT-III 1. Select "BCM". 2. With "DATA MONITOR" of "BUZZER", confirm "DOOR SW-DR" when the driver's door is operated. "DOOR SW-DR" When driver's door is opened When driver's door is closed : ON : OFF Without CONSULT-III Check voltage between BCM harness connector and ground. Terminals (+) BCM connector Terminal (-) Condition Voltage (Approx.) Driver's door is opened M19 47 Ground Driver's door is closed 0 Battery voltage OK or NG OK >> Front door switch LH signal is OK. Return to DI-54, "Trouble Diagnosis". NG >> GO TO 2. 2.CHECK FRONT DOOR SWITCH LH CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect BCM connector and front door switch LH connector. 3. Check continuity between BCM harness connector (A) and front door switch LH harness connector (B). PKIC0719E A Connector Terminal B Connector Terminal Continuity M19 47 B21 2 Yes 4. Check continuity between BCM harness connector (A) and ground. A Connector Terminal Ground Continuity M19 47 No OK or NG OK >> GO TO 3. NG >> Repair harness or connector. 3.CHECK FRONT DOOR SWITCH LH Check front door switch LH. Refer to DI-62, "Electrical Component Inspection". PKIC0720E Revision: October 2008 DI-56 2009 Sentra WARNING CHIME < SERVICE INFORMATION > OK or NG OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM". A NG >> Replace front door switch LH. Key Switch Signal Inspection (Without Intelligent Key) 1.CHECK FUSE INFOID:0000000004407659 B Check if the key switch 10A fuse [No. 19, located in the fuse block (J/B)] is blown. C OK or NG OK >> GO TO 2. NG >> Be sure to repair the cause of malfunction before installing new fuse. Refer to PG-3. D 2.CHECK BCM INPUT SIGNAL With CONSULT-III 1. Select "BCM". E 2. With "DATA MONITOR" of "BUZZER", confirm "KEY ON SW" when the key is operated. "KEY ON SW" F When key is inserted into ig- : ON nition key cylinder When key is removed from : OFF G ignition key cylinder Without CONSULT-III H Check voltage between BCM harness connector and ground. Terminals (+) BCM connector Terminal (-) Condition Voltage (Approx.) Key is inserted Battery voltage M18 37 Ground Key is removed 0 V OK or NG OK >> Key switch signal is OK. Return to DI-54, "Trouble Diagnosis". NG >> GO TO 3. 3.CHECK KEY SWITCH 1. Turn ignition switch OFF. 2. Disconnect key switch connector. 3. Check continuity between key switch terminals 1 and 2. Terminals Condition When key is inserted into ignition key cylinder 1 2 When key is removed from ignition key cylinder OK or NG OK >> GO TO 4. NG >> Replace key switch. 4.CHECK KEY SWITCH CIRCUIT 1. Disconnect BCM connector. Continuity Yes No I J DI PKIC0721E L M N O P WKIA5837E Revision: October 2008 DI-57 2009 Sentra WARNING CHIME < SERVICE INFORMATION > 2. Check continuity between BCM harness connector (A) and key switch harness connector (B). A Connector Terminal B Connector Terminal Continuity M18 37 M50 1 Yes 3. Check continuity between BCM harness connector (A) and ground. A Connector Terminal Ground Continuity M18 37 No OK or NG OK >> GO TO 5. NG >> Repair harness or connector. 5.CHECK KEY SWITCH POWER SUPPLY CIRCUIT Check voltage between key switch harness connector and ground. WKIA5838E Terminals (+) Voltage (-) (Approx.) Key switch connector Terminal M50 2 Ground Battery voltage OK or NG OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM". NG >> Repair harness or connector. LKIA0879E Key Switch and Ignition Knob Switch Signal Inspection (With Intelligent Key, When Me- chanical Key Is Used) INFOID:0000000004407660 1.CHECK FUSE Check if the key switch and ignition knob switch 10A fuse [No. 9, located in the fuse block (J/B)] is blown. OK or NG OK >> GO TO 2. NG >> Be sure to repair the cause of malfunction before installing new fuse. Refer to PG-3. 2.CHECK BCM INPUT SIGNAL With CONSULT-III 1. Select "BCM". 2. With "DATA MONITOR" of "BUZZER", confirm "KEY ON SW" when the key is operated. "KEY ON SW" When key is inserted into ignition key cylinder When key is removed from ignition key cylinder : ON : OFF Without CONSULT-III Revision: October 2008 DI-58 2009 Sentra WARNING CHIME < SERVICE INFORMATION > Check voltage between BCM harness connector and ground. Terminals (+) BCM connector Terminal (-) Condition Voltage (Approx.) Key is inserted Battery voltage M18 37 Ground Key is removed 0 OK or NG OK >> Key switch and ignition knob switch signal is OK. Return to DI-54, "Trouble Diagnosis". NG >> GO TO 3. 3.CHECK KEY SWITCH 1. Turn ignition switch OFF. 2. Disconnect key switch and ignition knob switch connector. 3. Check continuity between key switch and ignition knob switch terminals 1 and 2. Terminals Condition Continuity When key is inserted into ignition key cylinder Yes 1 2 When key is removed from ignition key cylinder No OK or NG OK >> GO TO 4. NG >> Replace key switch and ignition knob switch. 4.CHECK KEY SWITCH CIRCUIT 1. Disconnect BCM connector. 2. Check continuity between BCM harness connector (A) and key switch and ignition knob switch harness connector (B). A Connector Terminal B Connector Terminal Continuity M18 37 M49 1 Yes 3. Check continuity between BCM harness connector (A) and ground. A Connector Terminal Ground Continuity M18 37 No OK or NG OK >> GO TO 5. NG >> Repair harness or connector. 5.CHECK KEY SWITCH POWER SUPPLY CIRCUIT Revision: October 2008 DI-59 A B C PKIC0721E D E F G H WKIA5466E I J DI L M PKIC0723E N O P 2009 Sentra WARNING CHIME < SERVICE INFORMATION > Check voltage between key switch and ignition knob switch harness connector and ground. Terminals (+) Key switch and ignition knob switch connector Terminal (-) Voltage (Approx.) M49 2 Ground Battery voltage OK or NG OK >> Replace BCM. Refer to BCS-17, "Removal and Installation of BCM". NG >> Repair harness or connector. PKIC0724E Lighting Switch Signal Inspection INFOID:0000000004407661 1.CHECK BCM INPUT SIGNAL 1. Select "BCM" on CONSULT-III. 2. With "DATA MONITOR" of "BUZZER", confirm "LIGHT SW 1ST" when the lighting switch is operated. "LIGHT SW 1ST" Lighting switch (1st position) Lighting switch (OFF) : ON : OFF OK or NG OK >> Lighting switch signal is OK. Return to DI-54, "Trouble Diagnosis". NG >> Check the lighting switch. Refer to LT-60, "Combination Switch Inspection". Seat Belt Buckle Switch LH Signal Inspection INFOID:0000000004407662 1.CHECK SEAT BELT BUCKLE SWITCH LH SIGNAL INPUT (BCM) 1. Select "BCM" on CONSULT-III. 2. With "DATA MONITOR" of "BUZZER", confirm "BUCKLE SW" when the seat belt buckle switch LH is operated. "BUCKLE SW" When seat belt is fastened : OFF When seat belt is unfastened : ON OK or NG OK >> Inspection End. NG >> GO TO 2. 2.CHECK SEAT BELT BUCKLE SWITCH LH SIGNAL INPUT (COMBINATION METER) 1. Turn ignition switch ON. 2. Check voltage between combination meter harness connector M24 terminal 26 and ground. Terminals (+) Combination meter connector Terminal M24 26 OK or NG (-) Condition Voltage (Approx.) Ground Seat belt fastened Battery voltage Seat belt unfastened 0 LKIA0880E Revision: October 2008 DI-60 2009 Sentra WARNING CHIME < SERVICE INFORMATION > OK >> Replace combination meter. Refer to IP-12, "Removal and Installation". NG >> GO TO 3. 3.CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect combination meter connector and seat belt buckle switch LH connector. 3. Check continuity between combination meter harness connector (A) and seat belt buckle switch LH harness connector (B). A Connector Terminal B Connector Terminal Continuity M24 26 B16 1 Yes 4. Check continuity between combination meter harness connector (A) and ground. A Connector Terminal Ground Continuity M24 26 No OK or NG OK >> GO TO 4. NG >> Repair harness or connector. 4.CHECK SEAT BELT BUCKLE SWITCH LH Check seat belt buckle switch LH. Refer to DI-62, "Electrical Component Inspection". OK or NG OK >> Check seat belt buckle switch LH ground circuit. NG >> Replace seat belt buckle switch LH. Parking Brake Switch Signal Inspection 1.CHECK PARKING BRAKE SWITCH SIGNAL INPUT (COMBINATION METER) 1. Turn ignition switch ON. 2. Check voltage between combination meter harness connector M24 terminal 24 and ground. Terminals (+) Combination (-) meter Terminal connector Condition Voltage (Approx.) Parking brake released Battery voltage M24 24 Ground Parking brake applied 0 OK or NG OK >> Replace combination meter. Refer to IP-12, "Removal and Installation". NG >> GO TO 2. 2.CHECK PARKING BRAKE SWITCH CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect combination meter connector and parking brake switch connector. A B C D E WKIA5839E F G H I INFOID:0000000004407663 J DI L M WKIA5904E N O P Revision: October 2008 DI-61 2009 Sentra WARNING CHIME < SERVICE INFORMATION > 3. Check continuity between combination meter harness connector (A) and parking brake switch harness connector (B). A Connector Terminal B Connector Terminal Continuity M24 24 B24 1 Yes 4. Check continuity between combination meter harness connector (A) and ground. A Connector Terminal Ground Continuity M24 24 No OK or NG OK >> GO TO 3. NG >> Repair harness or connector. 3.CHECK PARKING BRAKE SWITCH Check parking brake switch. Refer to DI-62, "Electrical Component Inspection". OK or NG OK >> Check parking brake switch case ground. NG >> Replace parking brake switch. Electrical Component Inspection FRONT DOOR SWITCH LH Check continuity between terminal 2 and door switch case ground. Terminal Condition 2 Door switch When door switch is released. case ground When door switch is pushed. Continuity Yes No SEAT BELT BUCKLE SWITCH LH Check continuity between terminals 1 and 2. Terminal 1 2 Condition When seat belt LH is fastened. When seat belt LH is unfastened. Continuity No Yes PARKING BRAKE SWITCH WKIA5905E INFOID:0000000004407664 PKIC0245E WKIA1143E Revision: October 2008 DI-62 2009 Sentra WARNING CHIME < SERVICE INFORMATION > Check continuity between terminal 1 and parking brake switch case ground. Terminal Condition Parking When parking brake is applied. 1 brake switch case ground When parking brake is released. Continuity Yes No Revision: October 2008 DI-63 A B C LKIA0907E D E F G H I J DI L M N O P 2009 SentraAcrobat Distiller 6.0.1 (Windows)