Multipurpose & ultra comfortable. • Automatic buckles. • Adjustable shoulder, belt and lower part of thigh straps. • 4 tool holding handles for extra.
Product guide 2019 www.kratossafety.co.uk Logo Key Intensive use Alloy steel material Frequent use Aluminium steel material Regular use Stainless steel material Occasional use Max weight limit Product weight Maximum attachment 5kg weight Indicates number of users at once IP68 Waterproof rated Certified by International Climbing & Mountaineering Federation Approved for use on 0.50mm sharp edges ATEX Zone 2 approved Indicates angle of use Working at height is dangerous if your protection is not sufficient or not properly used. The risk of falling can be fatal. Against each of these risks, there is a Kratos Solution. Whatever the environment of the work at height, safety is a priority. That is why comfort and ergonomics are essential, because a more comfortable PPE will always be worn better and the user will always be protected better. Based on its commitment "safety for life" Kratos Safety is a provider focused on innovation, value creation, quality & expertise in design and manufacturing. Contents Section 1 Harnesses 4 Section 2 Tool Lanyards & Accessories 14 Section 3 Fall Arresters 17 Section 4 Shock Absorbing Lanyards 30 Section 5 Restraint & Work Positioning 35 Lanyards Section 6 Connectors 37 Section 7 Anchorages 42 Section 8 Rescue & Rope Access 51 Section 9 Head Protection 56 Section 10 Oil & Dirt Repellant 57 Range Section 11 Dielectric Product 58 Range Section 12 ATEX Free Blast Range 59 Section 13 "Fire Free" Range 60 Section 14 ANSI Product Range 61 Section 15 Load Arresters 62 Section 16 Kit Bags & Rucksacks 63 Section 17 Harness Kits 65 Section 18 Training & Servicing 67 3 SECTION 1 Harness & Belts 1 NEW DESIGN COMING SOON FA 10 101 00 2 Point Luxury Full Body Harness · Front & rear attachment points. · Automatic buckles. · Covered identification label. · Fully adjustable shoulder straps, chest & thigh straps. · Specially cushioned mesh net for better shock absorption & comfort of the user. · S-L (FA 10 101 00). · L-XXL (FA 10 101 01). 2 NEW DESIGN COMING SOON FA 10 201 00 4 Point Luxury Full Body Harness · Front & rear attachment points. · Work positioning belt with 2 D-rings. · Automatic buckles. · Covered identification label. · Fully adjustable shoulder straps, thigh straps & waist belt. · 2 tool holding loops at the back and 1 tool holding handle on the belt for extra karabiners. · Ideally positioned sit strap for extended comfort. · Specially cushioned mesh net for better shock absorption & comfort of the user. · S-L (FA 10 201 00). · L-XXL (FA 10 201 01). EN 361:2002 1.65 2.27 EN 361:2002 | EN 358:2000 3 FA 10 202 00 5 Point Luxury Full Body Harness NEW DESIGN COMING SOON · Front & rear D-rings. · Work positioning belt with 2 D-rings. · Automatic Buckles. · Covered identification label. · Fully adjustable shoulder straps, thigh straps & waist belt. · Tool holding loops & handles for extra karabiners & accessories. · Ideally positioned elasticated straps for extended comfort. · Specially cushioned mesh net for better shock absorption & comfort of the user. · S-L (FA 10 202 00). · L-XXL (FA 10 202 01). FA 10 215 00 Hybrid Airtech Full Body Harness COMING SOON · Dorsal & Sternal D-ring. · Work positioning belt with 2 D-rings. · Ventral D-ring for rope access. · Quick and easy to put on (can put on with your feet on the ground). · Multipurpose & ultra comfortable. · Automatic buckles. · Adjustable shoulder, belt and lower part of thigh straps. · 4 tool holding handles for extra karabiners. · Soft padding on waist and leg straps for extended comfort. · Pull-down D-rings to avoid unintentional bumping. · S-L (FA 10 215 00). · L-XXL (FA 10 215 01). 2.26 2.27 EN 361:2002 | EN 358:2000 | EN 813:2008 EN 361:2002 | EN 358:2000 | EN 813:2008 4 SECTION 1 Harness & Belts FA 10 216 00 Airtech Full Body Harness · Dorsal & Sternal D-ring. · Work positioning belt with 2 D-rings. · Ventral D-ring for rope access. · Quick and easy to put on (can put on with your feet on the ground). · Multipurpose & ultra comfortable. · Automatic buckles. · Adjustable shoulder, belt and lower part of thigh straps. · 4 tool holding handles for extra karabiners. · Soft padding on waist and leg straps for extended comfort. · Pull-down D-rings to avoid unintentional bumping. · S-L (FA 10 216 00). · L-XXL (FA 10 216 01). · Female S-XXL (FA 10 216 02). COMING SOON FA 10 216 00 FA 10 216 01 EN 361:2002 | EN 358:2000 | EN 813:2008 ULTRA LIGHT FA 10 216 02 2.26 NEW FA 10 114 00 Retroreflective Full Body Harness · Front & rear attachment points. · Extension strap with D-ring. · Retroreflective threads on webbing for increased visibility in dark areas. · Oil and dirt repellent Revolta webbing. · Revolta webbing provides increased durability due to its tear and cut repellent webbing. · Automatic buckles. · Fully adjustable shoulder, chest & thigh straps. · Velcro loops on shoulder straps for attaching gas detector/ communication box etc. · 2 tool-holding triangles for extra accessories. · S-L (FA 10 114 00). · L-XXL (FA 10 114 01). EN 361:2002 NEW FA 10 414 00 Work Belt For Self Respiratory Equipment · Two lateral D-ring attachment points. · Comfortable padding to provide full lumbar support. · Fully adjustable. · 4 tool-holding webbing loops and 3 rings for keeping extra accessories. · Retroreflective threads on webbing for increased visibility in dark areas. · Oil and dirt repellent Revolta webbing. · Revolta webbing provides increased durability due to its tear and cut repellent webbing. · Automatic buckles. · Fully adjustable shoulder, chest & thigh straps. · Universal: (FA 10 414 00). FA 10 114 00 + FA 10 414 00 combined: 1.66 0.41 5 SECTION 1 Harness & Belts 1 FA 10 107 00 2 Point Elasticated Full Body Harness · Front & rear D-rings. · INOX Stainless Steel components provide excellent corrosion protection. · Covered identification label. · Fully adjustable shoulder & thigh straps. · Made of elastic webbing for more comfort and impact resistance. · Universal (FA 10 107 00). 2 FA 10 208 00 4 Point Elasticated Full Body Harness · Front & rear D-rings. · Work positioning belt with 2 D-rings. · INOX Stainless Steel components provide excellent corrosion protection. · Covered identification label. · Fully adjustable shoulder & thigh straps. · Made of elastic webbing for more comfort and impact resistance. · Universal (FA 10 208 00). EN 361:2002 1.47 2.05 EN 361:2002 | EN 358:2000 3 FA 10 107 01 NEW DESIGN COMING SOON 2 Point Scaffold Full Body Harness · Front & rear D-rings. · Automatic buckles. · Covered identification label. · Spring buckles on shoulder straps to keep adjustment of the webbing. · Fully adjustable shoulder & thigh straps. · 2 web keepers on shoulder straps for easy placement of free lanyards. · Made of Elastic webbing in the upper part for more comfort and impact resistance. · Universal (FA 10 107 01). NEW DESIGN COMING SOON FA 10 207 00 4 Point Elasticated Rotative Full Body Harness · Front & rear attachment points. · Rotative work positioning belt with 2 D-rings. · Automatic buckles. · Covered identification label. · Fully adjustable shoulder straps, thigh straps & waist belt. · Shoulder straps are elasticated and have combination buckles. · 4 tool-holding loops and 1 handle at waist level for keeping extra accessories. · Special rotative belt and elastic straps for easy mobility and great comfort. · S-L (FA 10 207 00). · L-XXL (FA 10 207 01). EN 361:2002 1.60 2.25 EN 361:2002 | EN 358:2000 6 NEW DESIGN FA 10 112 00 COMING SOON 2 Point Sit Full Body Harness · Front & rear attachment points. · Automatic buckles. · Covered identification label. · Fully adjustable shoulder & thigh straps. · Sternal and shoulder straps have combination buckles. · Soft padding and elastic webbing for extended comfort and impact resistance. · S-L (FA 10 112 00). · L-XXL (FA 10 112 01). EN 361:2002 NEW DESIGN COMING SOON FA 10 205 00 4 Point Comfort Full Body Harness · Front & rear D-rings. · Work positioning belt with 2 D-rings. · Front attachment. · Automatic buckles. · Covered identification label. · Fully adjustable shoulder & thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · 4 tool-holding webbing loops and 3 tool- holding rings for extra accessories. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 205 00). EN 361:2002 | EN 358:2000 SECTION 1 Harness & Belts NEW DESIGN COMING SOON FA 10 206 00A 5 Point Comfort Suspension Full Body Harness · Front & rear D-rings. · Work positioning belt with 2 D-rings. · Ventral D-ring. · Combination buckles for easy adjustment. · 4 tool-holding loops & 3 tool-holding rings for extra accessories. · Soft padding on shoulder, waist and leg straps for extended comfort. · Universal (FA 10 206 00A). 2.25 EN 361:2002 | EN 358:2000 | EN 813:2008 NEW DESIGN COMING SOON FA 10 204 01 4 Point Comfort Full Body Harness · Front & rear D-rings. · Work positioning belt with 2 D-rings. · Extension strap allowing the user to easily connect himself to dorsal attachment with no external help. · Automatic buckles. · Covered identification label. · Fully adjustable shoulder, thigh straps & waist belt. · Shoulder and thigh straps differentiated by a dual colour scheme. · Soft padding on shoulder and waist straps & for extended comfort. · Universal (FA 10 204 01). 1.95 EN 361:2002 | EN 358:2000 2.25 2.01 7 SECTION 1 Harness & Belts NEW DESIGN COMING SOON FA 10 108 00 Single Point Full Body Harness · Rear D-ring. · Fully adjustable shoulder & thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 108 00). NEW DESIGN COMING SOON FA 10 105 00 2 Point Comfort Full Body Harness · Front & rear D-rings. · Fully adjustable shoulder & thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 105 00). 1.01 1.25 EN 361:2002 EN 361:2002 NEW DESIGN COMING SOON FA 10 111 00 3 Point Comfort Full Body Harness · Front & rear D-rings. · Automatic buckles. · Fully adjustable shoulder & thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · Ideally positioned sit strap for extended comfort. · S-L (FA 10 111 00). · L-XXL (FA 10 111 01). NEW DESIGN COMING SOON FA 10 105 00A 2 Point Comfort Full Body Harness · Front & rear D-rings. · Automatic buckles. · Fully adjustable shoulder & thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · Ideally positioned sit strap for extended comfort. · S-L (FA 10 105 00A). · L-XXL (FA 10 105 01A). 1.55 1.53 EN 361:2002 EN 361:2002 8 SECTION 1 Harness & Belts NEW DESIGN COMING SOON FA 10 106 00 Rescue Full Body Harness · Front & rear D-rings. · Extension rescue strap with D-ring. · Fully adjustable shoulder & thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 106 00). EN 361:2002 | EN 1497:2007 COMING SOON FA 10 301 00 2 Point Full Body Harness With Vest · Front & rear attachment points. · Grey polycotton work vest. · Adjustable zip system. · Automatic buckles. · Front attachment. · Fully adjustable vest, shoulder & thigh straps. · Inside storage pocket for straps when not in use. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 301 00). 1.45 1.35 EN 361:2002 FA 10 302 00 2 Point High-Visibility Full Body Harness · Front & rear attachment points. · Yellow polycotton work vest (240g/m²). · Adjustable zip system. · Automatic buckles. · Front attachment. · Fully adjustable vest, shoulder & thigh straps. · Inside storage pocket for straps when not in use. · Ideally positioned sit strap for extended comfort. · Reflective strips down the front for visibility & durable zipper. · Universal (FA 10 302 00). EN 361:2002 | EN 471 class 2.2 FA 10 303 00 2 Point High-Visibility Full Body Harness · Front & rear attachment points. · Orange polycotton work vest (240g/m²). · Adjustable zip system. · Automatic buckles. · Front attachment. · Fully adjustable vest, shoulder & thigh straps. · Inside storage pocket for straps when not in use. · Ideally positioned sit strap for extended comfort. · Reflective strips down the front for visibility & durable zipper. · Universal (FA 10 303 00). 1.45 EN 361:2002 | EN 471 class 2.2 1.45 9 SECTION 1 Harness & Belts NEW DESIGN COMING SOON FA 10 102 00 Single Point Full Body Harness · Rear D-ring. · Adjustable thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 102 00). NEW DESIGN COMING SOON FA 10 103 00 2 Point Full Body Harness · Front & real attachment points. · Adjustable thigh straps. · Shoulder and thigh straps differentiated by a dual colour scheme. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 103 00). EN 361:2002 NEW DESIGN COMING SOON FA 10 203 00 4 Point Full Body Harness · Front & rear attachment points. · Work positioning belt with 2 D-rings. · Adjustable thigh straps & waist belt. · Shoulder and thigh straps differentiated by a dual colour scheme. · 2 tool-holding loops and 1 tool-holding ring for extra accessories. · Ideally positioned sit strap for extended comfort. · Universal (FA 10 203 00). EN 361:2002 | EN 358:2000 10 0.72 0.79 EN 361:2002 NEW DESIGN COMING SOON FA 10 213 00 4 Point Comfort Full Body Harness · Front & rear D-rings. · Work positioning belt with 2 D-rings. · Waist level D-ring for rope access. · Adjustable shoulder, thigh straps & waist belt. · Shoulder, thigh and belt straps are provided with combination buckles for easy adjustment. · 4 tool-holding webbing loops and 3 tool-holding rings for extra accessories. · Universal (FA 10 213 00). 1.33 1.95 EN 361:2002 | EN 358:2000 | EN 813:2008 SECTION 1 Harness & Belts NEW DESIGN COMING SOON FA 10 404 00 Luxury Work Positioning Belt · One front and two lateral D-ring attachment points. · Automatic buckles. · Adjustable thigh straps & waist belt. · Suitable for all rope access applications. · 3 extra handles at the back for keeping extra accessories. · Ideally positioned elasticated straps for extended comfort. · Specially cushioned mesh net for better shock absorption & comfort of the user. · S-L (FA 10 404 00). · L-XXL (FA 10 404 01). COMING SOON 100 FA 10 500 00 BAMBOU Climbing Belt · One front ventral attachment point. · Adjustable waist & leg straps. · Comfortable padding. · Protected textile loop at ventral level. · Large size adjustment span (child to adult) · Suitable for intense communal use. · Universal (FA 10 500 00). 1.45 2.27 EN 358:2000 | EN 813:2008 EN 12277:2016 Type C NEW DESIGN COMING SOON 2019 NEW DESIGN COMING SOON 2019 FA 10 401 00 Comfort Work Positioning Belt · Two lateral D-ring attachment points. · Comfortable padding to provide full lumbar support. · Fully adjustable. · 4 tool-holding webbing loops and 3 rings for keeping extra accessories. · Universal (FA 10 401 00). FA 10 402 00 Work Positioning Belt · Two lateral D-ring attachment points. · Optimum width padding to provide sufficient lumbar support. · Fully adjustable. · 2 tool-holding webbing loops and 1 tool-holding ring for keeping extra accessories. · Universal (FA 10 402 00). EN 358:2000 0.65 EN 358:2000 0.45 11 SECTION 1 Harness & Belts 12 P a g e Oil & dirt repellent products 5 7 P a g e 5 Voltage resistant products 8 P a g e 5 Explosive atmosphere protection products 9 P a g e 6 Flame resistant products 0 P a g e 6 1 American National Standard Institute products SECTION 1 Harness & Belts Harness - Information A full body harness is the ideal body wear that should be worn by a worker, since it distributes the force of impact incurred in the event of a fall evenly on the thighs and torso region of the body. The material of construction for Kratos Harnesses is polyester. Polyester is the most popular choice of webbing as it has the least elongation properties when compared to other materials, therefore the harness does not stretch dangerously when subjected to a fall & the wearer hence does not suffer the risk of slipping out of the harness. Before wearing a harness, it is important to inspect it for certain features: · Hold the harness by the back D-ring, and let the straps fall in place. The harness has clear and seperate colours for the shoulder and thigh straps; so they can be easily distinguished. · Inspect the harness webbing for any cuts, burns or damages. · Check the stitches for their continuity. · Carefully look for any evidence of corrosion on the metal parts. 140* Safety harnesses tested to 140kg, only when used in conjunction with a fall arrest device with equal kg capacity. Size: The chart hereunder indicates the body's measures. For the wearing of a harness over clothing, the harness' adjustments allow to obtain the right size. Measure (cm) A - Thigh Size B - Chest Size C - Waist Size D - Stature S - L 48 - 70 94 - 114 60 - 105 160 - 185 UNIVERSAL 55 - 90 98 -128 70 - 115 160 - 200 L - XXL 65 - 95 114 - 134 75 - 125 170 - 200 B C D A · For selecting a harness or a harness with integrated vest, the essential measurements are the thigh size and the chest size, the other measurements are given as an indication. · Standard harness size is universal unless otherwise stated. · For selecting a belt, the essential measurement is the waist size. 13 SECTION 2 Tool Lanyards & Accessories TS 90 001 00 Tool Connecting Stretch Lanyard · Polyester stretch webbing material. · For connecting tools to harness or belt of the user. · Aluminium karabiner with a 15mm gate opening. · Cord length 340mm with pull cord attachment. · Maximum Length: 1.3m. 5kg 5kg ea TS 90 001 02 Forked Tool Connecting Stretch Lanyard · Polyester stretch webbing material. · For connecting 2 tools to harness or belt of the user. · Aluminium karabiner with a 15mm gate opening. · Cord length 340mm with pull cord attachment. · Maximum Length: 1.3m. 0.06 0.08 10kg 2kg TS 90 001 01 Heavy Tool Connecting Stretch Lanyard TS 90 001 03 Tool Connecting Wristband Lanyard · Polyester stretch webbing material. · For connecting heavy tools such as a chainsaw or similar cutting tool to harness or belt of the user. · Steel ring (inside dia 38mm) for connecting to a tool holding hook. · Maximum Length: 1.3m. · Polyester stretch webbing material. · Wristband made of resistance and comfortable fabric. · Wristband width 65mm. · For connecting tools to harness or belt of the user. · Aluminium karabiner with a 15mm gate opening. · Cord length 120mm with pull cord attachment. · Maximum Length: 0.5m. 0.13 0.04 14 SECTION 2 Tool Lanyards & Accessories TS 90 001 06 Tool Connecting Stretch Lanyard with Integrated Karabiners · Polyester stretch webbing material. · For connecting tools to harness or belt of the user. · Has 2 steel locking karabiners, with gate opening 8mm. · Maximum Length: 1m. 5kg TS 90 001 07 Aluminium Karabiner · Aluminium karabiner for connecting tools to harness or belt. · Gate opening: 15mm. · Body dia: 7mm. · Minimum breaking strength: 90 daN. 0.08 0.03 10kg* 2kg TS 90 001 04 D-ring Attachment · Attachment with integrated polyester webbing material. · Webbing has a 60mm passage. · Steel D-ring (inside dia 22mm). · Can be installed on the belt or tool. · Tool attachment up to 10kg, only 2kg max when used with selfmerging silicone tape. · Length: 100mm. · Width: 25mm. TS 90 001 05 Self-merging Silicone Tape · Self-merging silicone tape which bonds to itself under pressure on any surface. · Recommended for attaching tools of 2kg max. When used with D-ring attachment. · Tool attachments up to 2kg. · Length: 3m. · Width: 25.4mm. 0.03 0.08 15 SECTION 2 Tool Lanyards & Accessories FA 10 903 00 Removable Extension Strap with D-ring · Can be fitted to the harness dorsal D-ring to alloy easier attachment of lanyard or fall arrest device. · Length: 400mm. NEW DESIGN COMING SOON FA 10 906 00 Removable Shoulder Pad · Foam with knitted mesh pad, designed to provide a better comfort on a classic harness. · To suit harnesses with 45mm wide webbing. · Sold in pairs. · Length: 350mm. · Size: Universal. 0.25 0.15 FA 10 901 00 Suspension Trauma Relief Strap FA 10 902 00 Removable Dorsal Fin · Extremely effective, specially designed to help relieve the negative effects of suspension trauma. · Compact and light-weight. · Does not affect the activity of worker while at work. · Can be fitted to all harnesses with 45mm webbing. · Foam with knitted mesh pads. · Designed for extra comfort on classic harnesses. · Allows the suspended worker to stand up in the harness to relieve pressure. · Easy to attach to the harness with the help of the textile loop and velcro provided. 0.10 0.20 FA 10 905 00 Removable Abrasion Resistant Shoulder Pad · Specially designed for shoulder protection. · Complete with pressure buttons. FA 10 904 00 Removable Tool or Lanyard Keeper · Can be fitted onto harness using the velcro attachment. FA 10 907 00 Webbing End NEW · Set composed of 4 webbing end clips and 4 webbing end caps. · Allows to "re-create" a manufactured end on a harness or belt strap. 0.01 0.01 0.01 16 FA 20 401 20 Olympe Retractable Wire Rope Fall Arrest Block complete with Integrated Recovery System · 10m (FA 20 401 10) [COMING SOON]. · 20m (FA 20 401 20). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 12 kN. · Integrated recovery system. · Can be fitted to Kratos tripod or MultiSafeWay using the additional adaption kits. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.5mm. FA 60 001 04 (10m) FA 60 001 03 (20m) Adaption Kit Suits FA 60 001 00 & FA 60 002 00 EN 360:2002 | EN 1496:2006 Class B FA 60 022 05 (10m) FA 60 022 04 (20m) Adaption Kit Suits MultiSafeWay FA 60 022 00 FA 20 401 30 Olympe Retractable Wire Rope Fall Arrest Block complete with Integrated Recovery System · 30m (FA 20 401 30). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 12 kN. · Integrated recovery system. · Can be fitted to Kratos tripod or MultiSafeWay using the additional adaption kits. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.5mm. FA 60 001 02 Adaption Kit Suits FA 60 001 00 & FA 60 002 00 EN 360:2002 | EN 1496:2006 Class B FA 60 022 03 Adaption Kit Suits MultiSafeWay FA 60 022 00 SECTION 3 Fall Arresters NEW SIZE 10M [COMING SOON] 109.0 280.0 348.8 [COMING SOON] 17 SECTION 3 Fall Arresters FA 20 400 15 Olympe Retractable Wire Rope Fall Arrest Block · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 12 kN. · Fitted with karabiner at anchorage end. · Equipped with wire rope brush. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.5mm. · 6m (FA 20 400 06). · 10m (FA 20 400 10). · 15m (FA 20 400 15). · 20m (FA 20 400 20). · 25m (FA 20 400 25). · 30m (FA 20 400 30). [COMING SOON] FA 20 400 25 FA 20 400 30 EN 360:2002 Now supplied with Guide Rope FA 20 402 15 Helixon Retractable Wire Rope Fall Arrest Block · Outer casing made from high impact resistant polymer. · Equipped with a carrying handle, wire rope brush and a window on the casing which allows easy access for inspection. · Delivered with a cord for guiding the winding back of the wire rope. · Minimum breaking strength: 12 kN. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.5mm. · 10m (FA 20 402 10). · 15m (FA 20 402 15). · 20m (FA 20 402 20). [COMING SOON] EN 360:2002 Now supplied with Guide Rope 18 FA 20 400 06 FA 20 400 10 223 172 87.0 FA 20 400 15 FA 20 400 20 279 223 94.0 FA 20 400 25 FA 20 400 30 425 278 109.0 NEW FA 20 402 10 FA 20 402 15 FA 20 402 20 SECTION 3 Fall Arresters FA 20 400 03 Retractable Wire Rope Fall Arrest Block · 3.5m (FA 20 400 03). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 12 kN. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.5mm · Smaller & lighter design. · Fitted with external in-built shock absorber. · Tested & approved for horizontal use according to VG 11.060. 112.8 83.0 FA 20 400 07 Retractable Wire Rope Fall Arrest Block · 7m (FA 20 400 07). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 12 kN. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.5mm · Smaller & lighter design. · Fitted with external in-built shock absorber. · Tested & approved for horizontal use according to VG 11.060. 157.0 186.5 Now supplied with Guide Rope 138 86.5 EN 360:2002 0.50mm Sharp edges with built-in shock absorber EN 360:2002 0.50mm Sharp edges with built-in shock absorber FA 20 402 03 Retractable Wire Rope Fall Arrest Block · 3.5m (FA 20 402 03). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 12 kN. · Equipped with a carrying handle, wire rope brush and a window on the casing which allows easy access for inspection. · Delivered with a cord for guiding the winding back of the wire rope. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.8mm. · Smaller & lighter design. · Fitted with external in-built shock absorber. · Tested & approved for horizontal use according to VG 11.060 (only with external shock absorber). · Also available without external shock absorber (FA 20 402 03B). EN 360:2002 COMING SOON 0.50mm Sharp edges with built-in shock absorber FA 20 402 07 Retractable Wire Rope Fall Arrest Block .· 7m (FA 20 402 07). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 12 kN. · Equipped with a carrying handle, wire rope brush and a window on the casing which allows easy access for inspection. · Delivered with a cord for guiding the winding back of the wire rope. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · Galvanised steel wire rope 4.8mm. · Smaller & lighter design. · Fitted with external in-built shock absorber. · Tested & approved for horizontal use according to VG 11.060 (only with external shock absorber). .· Also available without external shock absorber (FA 20 402 07B). EN 360:2002 COMING SOON Now supplied with Guide Rope 0.50mm Sharp edges with built-in shock absorber 19 SECTION 3 Fall Arresters FA 20 502 02 Retractable Webbing Fall Arrest Block · 2m (FA 20 502 02). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 15 kN. · Fitted with karabiner at anchorage end. · Swivel snap hook with at attachment end. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. · 20mm wide webbing. · Smaller & lighter design. · Fitted with external in-built shock absorber. · Tested & approved for horizontal use according to VG 11.060. · Fall Factor 2. 0.50mm Sharp edges with built-in shock absorber EN 360:2002 F2 FA 20 503 02 Retractable Webbing Fall Arrest Block · 2m (FA 20 503 02). · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 15 kN. · Fitted with karabiner at anchorage end. · Aluminium scaffold hook at attachment end. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. · 20mm wide webbing. · Smaller & lighter design. · Fitted with external in-built shock absorber. · Tested & approved for horizontal use according to VG 11.060. · Fall Factor 2. 00..5500mmmm Sharp edges with built-in shock absorber EN 360:2002 F2 FA 20 502 00 A Mono Retractable Block Connector · Allow to attach one FA 20 502 02 or one FA 20 503 02 block directly with the intersection of the dorsal straps of the user's harness. Offers a safe, quick and comfortable connection. · No additional connector is required. · Reduces the length of swing during the fall, thereby preventing the impact of retractable block on the user. EN 362:2004 20 FA 20 502 00 B Twin Retractable Block Connector · Allow to attach two FA 20 502 02 or two FA 20 503 02 block directly with the intersection fo the dorsal straps of the user's harness. This enables the usage of the block like a forked shock absorbing lanyard. · No additional connector is required. · Redcues the length of swing during the fall, thereby preventing the impact of retractable block on the user. EN 362:2004 TRI ON FA 20 410 10 Triton Waterproof Retractable Fall Arrest Block · 10m (FA 20 410 10). · Outer casing made from high impact resistant polymer with stainless steel cover. · Integrated carrying handle. · Minimum breaking strength: 12 kN. · The design of the internal mechanism in 2 different parts allows a perfect impermeability (meets IP68 level of IEC 60529) of the blocking-braking system. · As for the pulley & wire rope part, it allows to replace the wire rope quickly & easily with minimum tools. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. · 180 degrees pivoting anchorage loop. · Comes with Stainless Steel Wire Rope 4.5mm dia having: FA 50 203 20 with load indicator and a gripping handle. · Swivel snap hook with load indicator at attachment end. EN 360:2002 | IP68 | IEC 60529 FA 20 903 00 Housing for Retractable Fall Arrest Block · Protective housing to suit Olympe & Helixon retractable fall arrest blocks. · Water repellent. · Special design at the top part of the housing (locking of swivel spot) for increased protection against water & dirt. · Black colour, which makes the fall arrester more discreet in scenic environments. SECTION 3 Fall Arresters COMING SOON NEW 21 SECTION 3 Fall Arresters Lightweight Retractable Webbing Fall Arrest Block · Length: 2.5m. · Protective polymer casing. · Minimum breaking strength: 15 kN. · 50mm wide polyester webbing. · Incorporates a 45mm shock absorber. · Having a swivel attachment at anchorage end with load indicator. · FA 20 300 02 with karabiner at attachment end. · FA 20 301 02 with snap hook at attachment end. · FA 20 303 02 with snap hook at attachment end & scaffold hook at anchorage end. FA 20 300 02 FA 20 301 02 FA 20 303 02 EN 360:2002 FA 20 502 02 Lightweight Retractable Webbing Fall Arrest Block · Protective polymer casing. · Minimum breaking strength: 15 kN. · 50mm wide polyester webbing. · Incorporates a 45mm shock absorber. · Having a swivel attachment at anchorage end with load indicator. · Complete with snap hook at attachment end. · Length: 2.5m. · Fall Factor 2 (Max 1.8m). + OK FALL FACTOR 2 Can be used in configuration where it is necessary to work above the anchor point. Fall Factor 2 has a maximum length of 1.8m. 0.50mm EN 360:2002 22 COMING SOON FA 20 503 01 Lightweight Retractable Webbing Fall Arrest Block · Length: 1.8m. · Protective polymer casing. · Minimum breaking strength: 15 kN. · 21mm wide aramid webbing. · Fitted with external shock absorber. · Having a swivel attachment at anchorage end with load indicator. · Tested and approved for horizontal use, according to VG 11.060 (Rev. 08 - 10/2014). EN 360:2002 FA 20 501 02 Retractable Webbing Fall Arrest Block · Outer casing made from high impact strength polymer. · Minimum breaking strength: 15 kN. · Fitted with swivel and karabiner at anchorage end. · Snap hook at attachment end. · 25mm polyester webbing. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. · 2m (FA 20 501 02). EN 360:2002 FA 20 501 06 Retractable Webbing Fall Arrest Block · Outer casing made from high impact strength polymer. · Minimum breaking strength: 15 kN. · Fitted with swivel and karabiner at anchorage end. · Snap hook at attachment end. · 25mm polyester webbing. · Comes with an external inbuilt shock absorber. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. · Tested and approved for horizontal use, according to VG 11.060 (Rev. 08 - 10/2014). · 6m (FA 20 501 06). 0.50mm Sharp edges with built-in shock absorber EN 360:2002 SECTION 3 Fall Arresters FA 20 500 03 Retractable Webbing Fall Arrest Block · Outer casing made from high impact strength polymer. · Minimum breaking strength: 15 kN. · Fitted with swivel and karabiner at anchorage end. · Snap hook at attachment end. · 25mm polyester webbing. · Comes with an external inbuilt shock absorber. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. · Tested and approved for horizontal use, according to VG 11.060 (Rev. 08 - 10/2014). · 3.5m (FA 20 500 03). 0.50mm Sharp edges with built-in shock absorber EN 360:2002 FA 20 500 12 Retractable Webbing Fall Arrest Block · Outer casing made from high impact strength polymer. · Minimum breaking strength: 15 kN. · Fitted with swivel and karabiner at anchorage end. · Snap hook at attachment end. · 25mm polyester webbing. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. · 12m (FA 20 500 12). EN 360:2002 23 SECTION 3 Fall Arresters FA 20 504 03 Retractable Webbing Fall Arrest Block · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 15 kN. · Equipped with a carrying handle, wire rope brush and a window on the casing which allows easy access for inspection. · Delivered with a cord for guiding the winding back of the wire rope. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · 25mm wide polyester webbing. · Smaller & lighter design. · Fitted with external in-built shock absorber. · Tested & approved for horizontal use according to VG 11.060 · 3.5m (FA 20 504 03). · 6m (FA 20 504 06). EN 360:2002 NEW 0.50mm Sharp edges with built-in shock absorber FA 20 504 12 Retractable Webbing Fall Arrest Block · Outer casing made from high impact resistant polymer. · Minimum breaking strength: 15 kN. · Equipped with a carrying handle, wire rope brush and a window on the casing which allows easy access for inspection. · Delivered with a cord for guiding the winding back of the wire rope. · Fitted with karabiner at anchorage end. · Swivel snap hook with load indicator at attachment end. · 25mm wide polyester webbing. · Smaller & lighter design. · 12m (FA 20 504 12). EN 360:2002 FA 20 500 02 Twin Retractable Webbing Fall Arrest Block · 2m (FA 20 500 02). · Outer casing made from aluminium alloy. · Minimum breaking strength: 15 kN. · To be used wherever the user needs a greater freedom of movement and pass obstacles. · Remain secure permanently. · Fitted with swivel and karabiner at anchorage end. · Scaffold hooks at attachment end. · 25mm polyester webbing. · Internal braking mechanism to reduce the fall arrest force to less than 6 kN. EN 360:2002 FA 20 800 00 Vertical Lifeline Ratchet Pulley · Outer casing made from polymer. · Minimum breaking strength: 13 kN. · Ratchet Pulley is mainly recommended for adventure parks (tree climbing), to be used as a vertical lifeline. · The over-speed built in brake, activates instant blocking of the pulley in the 2 directions in case of fall. It ensures the security of the user while ascending and descending. · Provided in configuration of 2 different hauling ratios 3:1 & 5:1. · Has a swivel anchorage eye at the top. · Works as a Block, can be re-used, hence no servicing is required after each fall. · Works with 10.5mm Kernmantle rope (FA 70 010 99 - not included). EN 360:2002 FA 70 016 00 303.0 NEW Now supplied with Guide Rope 224.0 95.5 NEW FA 70 010 99 24 FA 20 103 00 A Rope Grab Fall Arrester on Kernmantle Rope 11mm Rope: · All ropes supplied seperately. FA 20 103 00 A Rope Grab (for use on 11mm rope) · EN353-2 works on 11mm kernmantle rope. · EN358 works on 12mm kermantle rope (available in 10 & 20m lengths). · Steel karabiner at anchorage end. · Simple opening and closing system. · Has a manual locked position to allow work on inclined roof, and also restraint positioning. · Spliced end is protected with a strong transparent covering sleeve. · Minimum breaking strength: > 15 kN. FA 20 103 00 B Rope Grab (for use on 11mm rope EN353-2 only) · 10m rope (FA 20 103 10). · 20m rope (FA 20 103 20). · 30m rope (FA 20 103 30). · 40m rope (FA 20 103 40). · 50m rope (FA 20 103 50). FA 20 103 20 20m 11mm Rope EN 353-2:2002 | EN 358-2000 FA 20 102 10 Captive Fall Arrester attached to 12mm Kernmantle Rope with Shock Absorber 12mm Rope: · Ropes sold fitted with fall arrester. · Rope ends protected by strong transparent sleeve which makes the stitching visible for easy inspection prior to use. · Minimum breaking strength: > 15 kN. · 10m rope (FA 20 102 10). · 20m rope (FA 20 102 20). · 30m rope (FA 20 102 30). · 40m rope (FA 20 102 40). · 50m rope (FA 20 102 50). EN 353-2:2002 SECTION 3 Fall Arresters 25 SECTION 3 Fall Arresters FA 20 100 00 A FA 20 100 00 B NEW FA 20 104 00 Rope Grab Fall Arrester to suit 12mm Polyamide Kernmantle Rope · All ropes supplied seperately. · Manual locked position to allow work on inclined roof. · Unique non-inverting system to prevent installing the device Rope Grab Fall Arrester to suit 14-16mm Polyamide Twisted Rope upside down. · Alloy steel rope grab. · Works on 12mm dia · All ropes supplied seperately. · Manual locked position to allow work on inclined roof. · Unique non-inverting system to prevent installing the device anchorage line. · Minimum breaking strength: 15 kN. upside down. · Alloy steel rope grab. · Works on 14-16mm dia anchorage line. · Minimum breaking strength: 15 kN. 0.66 EN 353-2:2002 EN 353-2:2002 FA 20 100 10 Anchor Line · 14-16mm dia polyamide twisted rope. · Abrasion resistant thimble to protect the loops from being damaged by metallic contact. · Spliced ends protected with a strong transparent covering sleeve. · 10m rope (FA 20 100 10). · 20m rope (FA 20 100 20). · 30m rope (FA 20 100 30). · 40m rope (FA 20 100 40). · 50m rope (FA 20 100 50). · 100m rope (FA 20 100 98). · 200m rope (FA 20 100 97). FA 20 104 10 Anchor Line · 12mm dia polyamide kernmantle rope. · Abrasion resistant thimble to protect the loops from being damaged by metallic contact. · Spliced ends protected with a strong transparent covering sleeve. · 10m rope (FA 20 104 10). · 20m rope (FA 20 104 20). · 30m rope (FA 20 104 30). · 40m rope (FA 20 104 40). · 50m rope (FA 20 104 50). FA 90 005 00 Edge Protector · Material: Stainless Steel. · Protects the rope from abrasion against sharp edges. · Edge ring guides protect multiple ropes from getting tangled. · Comes complete with attaching cable. EN 353-2:2002 26 EN 353-2:2002 FA 20 901 00 Counter Weight · Suits 9mm - 18mm rope dia. KS 7000 Vertical System The system is extremely flexible thanks to: · a top or end attachment point adjustable on a large number of existing profiles. · an intermediary attachment point, adaptable on a ladder bar (16mm min dia). · a cable end crimping piece to adjust the length of the wire. · the complete system comes with an installation guide. The sliding fall arrester is in Stainless Steel, it comes with 1 steel screw-locking karabiner that cannot be lost. It has a non-inverting system to prevent installing the device upside down on the anchor line. It's design allows the sliding fall arrester to be installed / uninstalled at any level on the cable. · Material: Stainless Steel. · Minimum breaking strength: > 15 kN. · Conforms to EN 353-1:2002. 1 2 3 4 5 6 7 8 9 NEW No. 1 2 3 4 5 6 7 8 9 Ref. FA 20 201 00 Description Mounting Brackets: Supplied with mounting hardware, this piece (high or low) fixes on square profiles, round profiles, U,H,T,L... Breaking strength: 10 kN. Comply with EN795 Class A1. FA 20 206 00 Shock Absorber: Necessary to reduce the impact force due to the arrest of the fall in the facility. FA 20 200 01 Rope Grab: Works on rigid stainless steel cable system. FA 20 202 00 Intermediate Cable Guide: Maintains the cable along the scale and allows the rope grab to pass through without any manipulation. This cable guide is used to avoid the cable flapping. To be Installed every 8m. FA 20 205 00 Tensioner: Regulates the tensioning of cable (tension about 80 daN) by simple rotation. FA 20 200 99 Wire Rope: Stainless steel, diameter 8mm, 7x19. FA 20 200 98 1m of Wire Rope with one manufactured end. FA 20 200 97 Aluminium Wire rope Cap. FA 20 207 00 Cable extremity: Allows the crimping of the cable at the desired length and eliminates the danger of any loose wire. FA 20 209 00 NEW Extremity plate for two ladder rungs: Used to install a vertical anchor line made of Stainless Steel wire rope on a ladder with U bolts and nylock nuts. Provides structural strength to the system. EN 353-1/2:2002 SECTION 3 Fall Arresters II2 G Exh IIC T6 Gb 1 2 6 3 4 7 5 27 SECTION 3 Fall Arresters KS 8000 Vertical System KS 8000 system is an integrated Fall Arrest solution made of a Vertical Aluminium Alloy Guide Rail over which glides a Guided-Type Fall Arrest Trolley. Fixed on a ladder and remaining on a structure, it allows the user to climb and descend without having to perform any manipulation. The complete system comes with an installation guide. Suitable for: · Ladders · Chimneys. · Windmills. · Transmission lines. · Advertisement billboards. The sliding fall arrester is stainless steel, the Trolley comes with a steel screw-locking karabiner for connecting to the user's harness. It has a non-inverting system to prevent installing the device upside down on the anchor line. In the event of a fall, the trolley immediately locks over the Rail, thus arresting the fall. The top and bottom extremities of the rail are equipped with a manual spring lock preventing the Trolley from accidentally moving out of the rail. 1 2 3 6 8 5 7 4 No. 1 2 3 4 5 6 7 Ref. FA 20 701 00 Description Aluminium Top Extension: Curved at the level of the ladder end over the working platform, allowing the user to be connected to the Trolley even at the termination of the ladder, ensuring complete safety. FA 20 702 01 Aluminium Rail Intermediate: Length: 3m. FA 20 700 00 Vertical Trolley: Stainless steel (316) Trolley with 4 Brass wheels, providing frictionless movement. Has a unique non-inverting system to prevent installing the device upside down on the anchor line. Has a unidirectional locking system to prevent the Trolley from sliding down the rail when not in use. FA 50 101 17 Steel screw-locking karabiner, opening gate 17mm. Used for connecting the user's harness to the Trolley. Breaking Strength > 25 kN. FA 20 705 00 Rung clamp: Helps to clamp the System onto the underlying ladder. To be installed every 1.5 mtrs. Stainlesssteel (316). FA 20 704 00 FA 20 703 01 Junction: Used for connecting 2 rails together. Stainless Steel (316). Aluminium Rail Extremity: Equipped with a manual spring lock that prevents the Trolley from accidentally moving out of the rail. Length 3m. EN 353-1/2:2002 28 II2 G Exh IIC T6 Gb 2 6 3 4 4 6 7 5 5 7 KS 9000 Vertical System This is a complete Fall Protection Ladder System which consists of Galvanized Steel Ladder Rungs over which is fixed the Vertical Anchorage Rail made of Aluminium Alloy. This system is an ideal choice for use where there are no pre-fabricated ladders or climbing structures available for climbing and can be fitted over various structures using different types of fasteners. The complete system comes with an installation guide. Suitable for: · Ladders · Chimneys. · Windmills. · Transmission lines. 1 3 6 · Advertisement billboards. The sliding fall arrester is stainless steel, the Trolley comes with a steel screw-locking karabiner for 3 connecting to the user's harness. It has a non-inverting system to prevent installing the device upside down on 7 4 the anchor line. In the event of a fall, 2 the trolley immediately locks over the Rail, thus arresting the fall. 5 The top and bottom extremities of the rail are equipped with a manual spring lock preventing the Trolley from accidentally moving out of the rail. 9 7 8 8 No. 1 2 3 4 5 6 7 8 9 Ref. Description FA 20 701 00 Aluminium Top Extension: Curved at the level of the ladder end over the working platform, allowing the user to be connected to the Trolley even at the termination of the ladder, ensuring complete safety. Length: 1,50 m. FA 20 702 01 Aluminium Rail Intermediate: Length: 3 m. FA 20 700 00 Vertical Trolley: Stainless steel (316) Trolley with 4 Brass wheels, providing frictionless movement. Has a unique non-inverting system to prevent installing the device upside down on the anchor line. Has a unidirectional locking system to prevent the Trolley from sliding down the rail when not in use. FA 50 101 17 Steel screw-locking karabiner, opening gate 17 mm. Used for connecting the user's harness to the Trolley. Breaking strength > 25 kN. FA 20 706 00 Mounting Bracket: Helps to clamp the Ladder System onto the underlying structure. Material: Stainless steel (316). FA 20 704 00 FA 20 703 00 FA 20 707 00 FA 20 708 00 Junction: Junction: Used for connecting 2 rails together. Stainless steel (316). Aluminium Rail Extremity: Equipped with a manual spring lock that prevents the Trolley from accidentally moving out of the rail. Length: 3m. Ladder Rung Assembly: One ladder rung comes with 2 pcs of fasteners. Material: Galvanised steel. Mounting Nut: Used for connecting the rail to the mounting bracket. Material: Stainless steel (316) EN 353-1/2:2002 SECTION 3 Fall Arresters II2 G Exh IIC T6 Gb 1 2 6 3 4 3 4 5 6 5 8 29 SECTION 4 Shock Absorbing Lanyards Easily calculate the minimum space under your work area and your clearance. Scan the barcode or speak to our Sales Office for further details. FA 30 000 45 Shock Absorber The Shock Absorber consists of a special white inner polyamide webbing, it is designed to dissipate the energy developed during a fall. It should be used in combinations with a lanyard (maximum 2m long). · Length: 205mm. · Spread Length: 1.5m. · Fitted with fall indicator label. · 45mm wide. FA 30 000 35 Shock Absorber The Shock Absorber consists of a special white inner polyamide webbing, it is designed to dissipate the energy developed during a fall. It should be used in combinations with a lanyard (maximum 2m long). · Length: 145mm. · Spread Length: 1.3m. · Fitted with fall indicator label. · 35mm wide. grav t -s FA 30 512 20 Shock Absorbing Anti-Cut Kernmantle Lanyard · 12mm dia. poly kernmantle rope. · New anti-cut rope designed to withstand sharp edges. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Fitted with aluminium scaffold hook one end and aluminium karabiner at the other end. · 1.2m (FA 30 512 12). · 2.0m (FA 30 512 20). 0.50mm Anti-cut rope designed to withstand sharp edges EN 355:2002 grav t -s FA 30 513 20 Shock Absorbing Anti-Cut Kernmantle Lanyard · 12mm dia. poly kernmantle rope. · New anti-cut rope designed to withstand sharp edges. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Fitted with aluminium scaffold hook one end and aluminium snap hook at the other end. · 2.0m (FA 30 513 20). 0.50mm Anti-cut rope designed to withstand sharp edges EN 355:2002 30 FA 30 514 20 Adjustable Shock Absorbing Expandable Kernmantle Lanyard · 12mm dia. poly kernmantle rope. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant thimble. · Fitted with aluminium scaffold hook one end and aluminium karabiner at the other end. · Adjustable from 1.4m - 2.0m. · 2.0m (FA 30 514 20). EN 355:2002 FA 30 502 15 Shock Absorbing Kernmantle Lanyard · 12mm dia. poly kernmantle rope with thimble eyes. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant thimble. · Stitching protected by a strong transparent sleeve. · Fitted with steel scaffold hook one end. · 1.5m (FA 30 502 15). · 1.8m (FA 30 502 20). EN 355:2002 FA 30 304 18 Shock Absorbing Webbing Lanyard · 30mm wide polyester webbing. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hook one end and steel karabiner other end. · 1.8m (FA 30 304 18). EN 355:2002 SECTION 4 Shock Absorbing Lanyards FA 30 503 15 Shock Absorbing Kernmantle Lanyard · 12mm dia. poly kernmantle rope with thimble eyes. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant thimble. · Stitching protected by a strong transparent sleeve. · Fitted with steel scaffold hook one end and steel snap hook at the other end. · 1.5m (FA 30 503 15). · 2.0m (FA 30 503 20). EN 355:2002 FA 30 500 15 Shock Absorbing Kernmantle Lanyard · 12mm dia. poly kernmantle rope with thimble eyes. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant thimble. · Stitching protected by a strong transparent sleeve. · 1.5m (FA 30 500 15). · 1.8m (FA 30 500 20). EN 355:2002 FA 30 303 15 Shock Absorbing Webbing Lanyard · 30mm wide polyester webbing. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hook one end and steel snap hook other end. · 1.5m (FA 30 303 15). · 2.0m (FA 30 303 20). EN 355:2002 31 SECTION 4 Shock Absorbing Lanyards FA 30 300 15 Shock Absorbing Webbing Lanyard · 30mm wide polyester webbing. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hook one end and steel karabiner other end. · 1.5m (FA 30 300 15). · 1.8m (FA 30 300 20). EN 355:2002 NEW DESIGN FA 30 522 10 Aluminium Shock Absorbing Kernmantle Lanyard · 11mm dia. poly kernmantle rope. · 35mm wide webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with auminium scaffold hook one end and aluminium karabiner at the other end. · 1.0m (FA 30 522 10). · 1.5m (FA 30 522 15). · 2.0m (FA 30 522 20). EN 355:2002 FA 30 702 20 Shock Absorbing Expandable Webbing Lanyard · 30mm wide polyester webbing. · 35mm webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hook one end and thimble eye other end. · Also available with steel snap hook fitted at thimble end (FA 30 703 20). · 2.0m (FA 30 702 20). EN 355:2002 NEW DESIGN FA 30 900 20 Shock Absorbing Expandable Webbing Lanyard · 45mm wide protective elasticated webbing. · Shock absorber within the central webbing weaving with progressive deformation. · Reduces fall impact to less than 6 kN. · Fall indicator. · Fitted with auminium scaffold hook one end and aluminium karabiner other end. · Relaxed length: 1.4m. · Expanded length: 2.0m. EN 355:2002 COMING SOON COMING SOON FA 30 722 20 Shock Absorbing Expandable Webbing Lanyard FA 30 820 15 Y Forked Shock Absorbing Expandable Webbing Lanyard · 35mm expandable polyester webbing. · 35mm expandable polyester webbing. · 45mm wide controlled-tear webbing shock absorber. · 45mm wide controlled-tear webbing shock absorber. · Compact shock absorber, protected by a small · Compact shock absorber, protected by a small zipper pouch, easily openable for internal control. zipper pouch, easily openable for internal control. · Reduces fall impact to less than 6 kN. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular · Loops protected by an abrasion resistant tubular webbing. · Fitted with auminium scaffold hooks one end. · Also available with aluminium snap hook fitted webbing. · Fitted with auminium scaffold hooks at forked ends and aluminium karabiner at the other end. · Also available with aluminium snap hook fitted at pouch end (FA 30 723 20). at pouch end (FA 30 723 20). · Relaxed length: 1.4m. · Relaxed length: 1.2m. · Expanded length: 1.8m. 0.50mm · Expanded length: 1.5m. 0.50mm EN 355:2002 EN 355:2002 32 SECTION 4 Shock Absorbing Lanyards NEW DESIGN FA 30 614 20 Y Forked Aluminium Adjustable Shock Absorbing Kernmantle Lanyard · 11mm dia. poly kernmantle rope. · 35mm wide webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with auminium scaffold hooks at forked ends and aluminium karabiner at the other end. · Adjustable from 1.4m to 2.0m. · 2.0m (FA 30 614 20). EN 355:2002 | VG11 11.063 grav t -s FA 30 610 15 Y Forked Anti-Cut Shock Absorbing Kernmantle Lanyard · 12mm dia. poly kernmantle rope. · 35mm wide webbing shock absorber. · Reduces fall impact to less than 6 kN. · New anti-cut rope designed to withstand sharp edges. · Loops protected by an abrasion resistant tubular webbing. · Fitted with auminium scaffold hooks at forked ends and aluminium karabiner at the other end. · 1.5m (FA 30 614 20). 0.50mm Anti-cut rope designed to withstand sharp edges EN 355:2002 | VG11 11.063 FA 30 600 15 Y Forked Shock Absorbing Kernmantle Lanyard · 12mm dia. poly kernmantle rope. · 35mm wide webbing shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hooks at forked ends and steel karabiner at the other end. · 1.0m (FA 30 600 10). · 1.5m (FA 30 600 15). EN 355:2002 | VG11 11.063 FA 30 1000 20 Y Forked Shock Absorbing Expandable Webbing Lanyard · 45mm wide protective elasticated webbing. · Shock absorber within the central webbing weaving with progressive deformation. · Reduces fall impact to less than 6 kN. · Fall indicator at forked ends. · Fitted with steel scaffold hooks at forked ends and steel karabiner at the other end. · 2.0m (FA 30 1000 20). EN 355:2002 | VG11 11.063 FA 30 400 18 Y Forked Shock Absorbing Webbing Lanyard · 30mm wide polyester webbing. · 35mm wide shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hooks at forked ends and steel karabiner at the other end. · 1.8m (FA 30 400 18). EN 355:2002 | VG11 11.063 FA 30 800 15 Y Forked Shock Absorbing Expandable Webbing Lanyard · 45mm wide polyester elasticated webbing. · 35mm wide shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hooks at forked ends and steel karabiner at the other end. · Relaxed length: 1.0m. · Expanded length: 1.5m. EN 355:2002 | VG11 11.063 33 SECTION 4 Shock Absorbing Lanyards FA 30 620 15 Y Forked Shock Absorbing Expandable Webbing Lanyard · 11mm dia. poly kernmantle rope. · 35mm wide shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with aluminium scaffold hooks at forked ends and aluminium karabiner at the other end. · 1.5m (FA 30 620 15). EN 355:2002 FA 30 200 15 Y Forked Shock Absorbing Twisted Rope Lanyard · 12mm dia. poly twisted rope. · 44mm wide shock absorber. · Reduces fall impact to less than 6 kN. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel scaffold hooks at forked ends and steel karabiner at the other end. · 1.5m (FA 30 200 15). EN 355:2002 | VG11 11.063 34 FA 40 300 15 · 30mm wide polyester webbing. · Breaking strength: 22 kN. · 1.5m (FA 40 300 15). EN 354:2010 FA 40 302 15 · 30mm wide polyester webbing. · Breaking strength: 22 kN. · 1.5m (FA 40 302 15). EN 354:2010 FA 40 303 15 · 30mm wide polyester webbing. · Breaking strength: 22 kN. · 1.5m (FA 40 303 15). EN 354:2010 FA 40 500 15 · 12mm kernmantle rope. · Breaking strength: 22 kN. · 1.0m (FA 40 500 10). · 1.5m (FA 40 500 15). · 2.0m (FA 40 500 20). EN 354:2010 FA 40 502 15 · 12mm kernmantle rope. · Breaking strength: 22 kN. · 1.0m (FA 40 502 10). · 1.5m (FA 40 502 15). · 2.0m (FA 40 502 20). EN 354:2010 FA 40 503 15 · 12mm kernmantle rope. · Breaking strength: 22 kN. · 1.0m (FA 40 503 10). · 1.5m (FA 40 503 15). · 2.0m (FA 40 503 20). EN 354:2010 FA 40 600 15 · 12mm kernmantle rope. · Breaking strength: 22 kN. · 1.0m (FA 40 600 10). · 1.5m (FA 40 600 15). EN 354:2010 SECTION 5 Restraint & Work Positioning Lanyards 30 mm 30 mm 30 mm 11 mm 11 mm 11 mm 11 mm 35 SECTION 5 Restraint & Work Positioning Lanyards FA 40 901 20 Adjustable Work Positioning Webbing Lanyard · 30mm wide polyester webbing. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel karabiner one end and steel snap hook at the other end. · Forged alloy steel ring adjuster, for adjusting length of lanyard. · 2.0m max (FA 40 901 20). 30 mm EN 358:2000 FA 40 902 20 Adjustable Work Positioning Kernmantle Rope Lanyard · 12mm dia. poly kernmantle rope. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel karabiner one end and steel snap hook at the other end. · Forged alloy steel ring adjuster, for adjusting length of lanyard. · 2.0m max (FA 40 902 20). 11 mm EN 358:2000 FA 40 904 20 Adjustable Work Positioning Grip Adjusting Lanyard · 14mm dia. poly twisted rope. · Abrasion resistant thimble to protect the loop from damage by the connector. · Fitted with steel karabiner one end and steel snap hook at the other end. · Stainless steel rope grab adjuster for progressive movement. · 0.6m (2.0m) or 1.5m (4.0m) rope protective webbing sleeve. · 2.0m (FA 40 904 20). · 4.0m (FA 40 904 40). 14 mm EN 358:2000 36 FA 40 900 20 Adjustable Work Positioning Twisted Rope Lanyard · 14mm dia. poly twisted rope. · Loops protected by an abrasion resistant tubular webbing. · Fitted with steel karabiner one end and steel snap hook at the other end. · Forged alloy steel ring adjuster, for adjusting length of lanyard. · 2.0m max (FA 40 900 20). 14 mm EN 358:2000 FA 40 903 20 Adjustable Work Positioning Grip Adjusting Lanyard · 12mm dia. poly kernmantle rope. · Abrasion resistant thimble to protect the loop from damage by the connector. · Fitted with steel karabiner one end and steel snap hook at the other end. · Steel rope grab adjuster for progressive movement. · 0.6m (2.0m) or 1.5m (4.0m) rope protective webbing sleeve. · 2.0m (FA 40 903 20). · 4.0m (FA 40 903 40). 11 mm EN 358:2000 FA 40 906 50 Adjustable Work Positioning Grip Adjusting Lanyard · 12mm dia. poly kernmantle rope. · Abrasion resistant thimble to protect the loop from damage by the connector. · Fitted with steel snap hook at one end. · Aluminium rope grab adjuster for progressive movement fitted with karabiner. · 1.6m rope protective webbing sleeve. · 5.0m (FA 40 906 50). 12 mm EN 358:2000 FA 50 101 17 Steel Screw Locking Karabiner · Alloy steel material. · Gate opening: 18mm. · Breaking strength: 25 kN. · Keylock version: FA 50 101 17B EN 362:2004 - Class B FA 50 301 23 Steel Triple Action Locking Karabiner · Alloy steel material. · Gate opening: 21mm. · Breaking strength: 25 kN. · Keylock version: FA 50 301 23B EN 362:2004 - Class B FA 50 207 55 Steel Scaffold Hook · Alloy steel material. · Gate opening: 50.8mm. · Breaking strength: 23 kN. · Ergonomic Grip. EN 362:2004 - Class T FA 50 213 80 Steel Tower Hook · Alloy steel material. · Gate opening: 85mm. · Breaking strength: 23 kN. EN 362:2004 - Class T Ø10.0 56.5 107.0 FA 50 102 17 Steel Screw Locking Karabiner · Alloy steel material. · Gate opening: 18mm. · Breaking strength: 25 kN. · Captive pin. EN 362:2004 - Class B 67.0 Ø11.0 111.0 FA 50 202 17 Steel Snap Hook · Alloy steel material. · Gate opening: 16mm. · Breaking strength: 23 kN. 127.0 159.0 1.5 214.0 EN 362:2004 - Class T FA 50 203 20 Steel Swivel Snap Hook with Load Indicator · Alloy steel material. · Gate opening: 20mm. · Breaking strength: 23 kN. EN 362:2004 - Class T FA 50 215 50 Steel Tower Hook · Alloy steel material. · Gate opening: 50mm. · Breaking strength: 23 kN. EN 362:2004 - Class T 129.0 SECTION 6 Connectors Ø10.0 56.5 55.8 58.0 37 191.5 210.2 107.0 SECTION 6 Connectors FA 50 216 55 Tower Hook · Alloy steel material. · Gate opening: 55mm. · Breaking strength: 23 kN. EN 362:2004 - Class B FA 50 400 16 Oval Quick Link · Alloy steel material. · Gate opening: 18mm. · Breaking strength: 32 kN. EN 362:2004 - Class Q NEW FA 50 224 18 Quarter Turn Locking Karabiner · Alloy steel material. · Gate opening: 16mm. · Breaking strength: 25 kN. EN 362:2004 - Class B NEW FA 50 107 15B Screw Locking Karabiner · Aluminium steel material. · Gate opening: 15mm. · Breaking strength: 23 kN. EN 362:2004 - Class B 38 88.0 71.0 115.0 Ø 8.0 34.0 FA 50 106 22 Quarter Turn Locking Karabiner · Stainless steel material. · Gate opening: 22.5mm. · Breaking strength: 25 kN. EN 362:2004 - Class B FA 50 401 10 Delta Quick Link · Alloy steel material. · Gate opening: 10mm. · Breaking strength: 22 kN. EN 362:2004 - Class Q NEW FA 50 225 23B Quarter Turn Locking Karabiner · Alloy steel material. · Gate opening: 22mm. · Breaking strength: 40 kN. EN 362:2004 - Class B NEW FA 50 900 00 Karabiner Holding Ring · Set of 10pcs. · To be used on unprotected end loops on 9mm to 12mm rope dia. 69.5 Ø11.0 Ø 8.0 56.0 FA 50 103 22 Screw Locking Karabiner · Aluminium steel material. · Gate opening: 22.5mm. · Breaking strength: 23 kN. · Keylock version: FA 50 103 22B. EN 362:2004 - Class B FA 50 201 22 Quarter Turn Locking Karabiner · Aluminium steel material. · Gate opening: 21mm. · Breaking strength: 23 kN. · Keylock version: FA 50 201 22B. EN 362:2004 - Class B FA 50 302 22 Triple Action Locking Karabiner · Aluminium steel material. · Gate opening: 21mm. · Breaking strength: 23 kN. · Keylock version: FA 50 302 22B. EN 362:2004 - Class B FA 50 220 21 Quarter Turn Locking Hook · Aluminium steel. · Gate opening: 21mm. · Breaking strength: 23 kN. EN 362:2004 - Class B 69.0 Ø11.0 111.0 FA 50 105 22B Aluminium Screw Locking Karabiner · Aluminium steel material in green finish. · Gate opening: 18.5mm. · Breaking strength: 23 kN. · Individual Number. EN 362:2004 - Class B 67.5 FA 50 217 22B Quarter Turn Ø11.0 Locking Karabiner 111.0 · Aluminium steel material in green finish. · Gate opening: 21mm. · Breaking strength: 23 kN. · Individual Number. EN 362:2004 - Class B 67.5 FA 50 304 22B Triple Action Locking Karabiner Ø11.0 111.0 · Aluminium steel material in green finish. · Gate opening: 19.5mm. · Breaking strength: 23 kN. · Individual Number. EN 362:2004 - Class B 75.4 FA 50 212 21 Snap Hook · Aluminium steel material. · Gate opening: 21mm. · Breaking strength: 23 kN. 151.0 EN 362:2004 - Class T SECTION 6 Connectors 69.0 Ø11.0 67.5 Ø11.0 67.5 Ø11.0 73.7 39 111.0 111.0 111.0 131.5 350.7 SECTION 6 Connectors FA 50 208 60 Rebar Hook · Aluminium steel material. · Gate opening: 60mm. · Breaking strength: 22 kN. · Available in green finish: FA 50 218 60. EN 362:2004 - Class T FA 50 221 17 Swivel Quarter Turn Locking Hook · Aluminium steel material. · Fitted with load indicator. · Gate opening: 17mm. · Breaking strength: 23 kN. EN 362:2004 - Class B Page 58 FA 50 222 55 Dielectric Scaffold Hook · Steel with polymer composite. · Minimum voltage resistance: 14 kV. · Gate opening: 55mm. · Breaking strength: 23 kN. EN 362:2004 - Class T 135.0 236.0 110.0 70.5 120.3 189.7 242.8 FA 50 208 11 Large Rebar Hook · Aluminium steel material. · Gate opening: 100mm. · Breaking strength: 23 kN. EN 362:2004 - Class T FA 50 214 60 Rebar Hook · Aluminium steel material. · Gate opening: 60mm. · Breaking strength: 20 kN. EN 362:2004 - Class T Page 58 FA 50 223 15 Dielectric Snap Hook · Steel with polymer composite. · Minimum voltage resistance: 14 kV. · Gate opening: 55mm. · Breaking strength: 23 kN. EN 362:2004 - Class T 164.9 120.0 Ø14.0 69.5 243.0 164.8 40 FA 50 209 14 Anchorage Hook Large · Stainless steel material. · Gate opening: 140mm. · Breaking strength: 23 kN. EN 362:2004 - Class A FA 50 210 11 Anchorage Hook Regular · Stainless steel material. · Gate opening: 110mm. · Breaking strength: 23 kN. EN 362:2004 - Class A FA 50 211 75 Anchorage Hook Small · Stainless steel material. · Gate opening: 75mm. · Breaking strength: 23 kN. EN 362:2004 - Class A 330.0 350.0 Ø35.0 380.0 Ø35.0 Ø35.0 Ø140.0 Ø110.0 Ø75.0 SECTION 6 Connectors 41 SECTION 7 Anchorages FA 60 022 00 MultiSafeWay · Maximum load capacity: 300kg. · For access in confined spaces, works on a façade. · Having two eye bolts at lifting arm as attachment points. · Can swivel a complete 360 degrees on it's mounted base - 8 positions. · Strength of anchorage points greater than 12 kN. · Lifting arm is adjustable at 3 defined points (2.3m / 1.9m / 1.5m). · Provided with special stainless steel fasteners for fitting of our winch (FA 60 003 00 or FA 60 023 00). FA 60 022 01 Floor Mounting Bracket FA 60 022 02 Wall Mounting Bracket EN 795:2012 - Type A FA 60 001 00 Confined Space Tripod NEW DESIGN COMING SOON · 7ft (FA 60 001 00). · 10ft (FA 60 002 00). · Maximum load capacity: 500kg. · Telescopic legs adjustable height: 1.15m to 2.15m (7ft). 1.9m to 2.9m (10ft). · Wheelbase: 0.9m - 1.3m (7ft). 1.8m (10ft). FA 60 002 01 Tripod Footboard · With two mounted pulleys at the head of the Tripod in the prolongation of the main leg for passing the Winch cable. · Having two auxiliary eye bolts as attachment points. · Aluminium alloy cast head, legs in aluminium. · Steel support shoes provided with rubber sole to increase friction and impart more stability. · Strength of anchorage point greater than 12 kN. · Every Tripod is provided with inbuilt fixture for attaching our winches FA 60 003 20 (20m) / FA 60 003 30 (30m). Tripod bag included! EN 795:2012 - Type B | Machinery Directive 42 34.87 EN1808 [COMING SOON] SECTION 7 Anchorages FA 60 002 01 Quadpod COMING SOON · Quadpod is a new lightweight, versatile and durable system thatgives the user the possibility to safely perform the rescue underminimum time. · Thanks to it's 4 multi-positioning telescopic legs (1.21m to 1.75m),Quadpod is an excellent tool for inclined planes rescue (such as cliff top or mountains) and confined space rescue. · Tripod bag included. · It can be used with 2, 3 or 4 legs with the help of proper rigging webbings (included). · Material: Aluminium. · Minimum breaking strength: 25 kN. · Maximum allowable load under head: 500kg. EN 795:2012 - Type B | TS 16415:2013 - Type B, Machinery Directive, EN 1808 Lashing Webbing Included 15.56 FA 60 103 00 Hexapod COMING SOON · Designed to be used where a classic tripod cannot be installed, for instance a trench, hole, silo or a well with a large dia. The system is versatile and can be adapted to a wide range of situations. · Composed of 2 Tripods (FA 60 001 00), connected through a horizontal rail in which slide 2 trolleys. All the accessories of a classic Tripod can be installed on the Hexapod. · Anchorage points: 2x2 anchorage points under the head of each Tripod, and 2 mobile trolleys. · Can be used by 2 people at the same time. · Max working load of the trolleys: 500kg. 1.80 m · Each Tripod is provided with inbuilt fixture for attaching a winch, as well as a pulley. · Minimum breaking strength: 25 kN. 4.20 m · Height adjustment: 1.15m - 2.15m. 49.33 EN 795:2012 - Type B | TS 16415:2013 - Type B FA 60 003 20 Rescue & Work Winch · Length: 20m. · Maximum load capacity: 500kg. · 4.8mm dia galvanised steel wire rope. · Safe working load: 135kg · Max material load: 250kg (Machinery Directive). · To be used for raising or lowering of personnel or material into confined spaces. · Equipped with bolting fixture for robust fitting on to the Tripod (FA 60 001 00 / FA 60 002 00). EN 1496:2006 - Class A [COMING SOON] 7.95 To be used with a Retractable Fall Arrester (EN360) when deployed for raising or lowering a person [COMING SOON] FA 60 003 30 Rescue & Work Winch · Length: 30m. · Maximum load capacity: 500kg. · 4.8mm dia galvanised steel wire rope. · Safe working load: 135kg · Max material load: 250kg (Machinery Directive). · To be used for raising or lowering of personnel or material into confined spaces. · Equipped with bolting fixture for robust fitting on to the Tripod (FA 60 001 00 / FA 60 002 00). 9.65 EN 1496:2006 - Class A To be used with a Retractable Fall Arrester (EN360) when deployed for raising or lowering a person 43 SECTION 7 Anchorages FA 60 007 02 25MTR 4 User Horizontal Temporary Lifeline NEW · Length: 5m - 25m. · Minimum breaking strength: 23 kN. · Complete with crossover rings. · 16mm dia. poly kernmantle rope. · Temporary and reusable system designed to provide a safe anchorage to the multi-users at the same time as working. · Equipped with special tensioner that allows tensioning of lifeline between two supports. · Has a swivel brass connector at one end and a stop knot secured with protective sleeve at other end. · Swivel Brass Connector - designed to prevent any twisting of the rope EN 795:2012 - Type C FFAA 6600 003037 1081 R25eMtraTcRta4bUleseTreHmoproizroanrytal HTeomripzoonrataryl LLiiffeelliinnee NNEEWW · Length: 5m - 25m. ·· MMianximleunmgtbhr:e1a8kimng. strength: 23 kN. ·· C6mommpldeitae. wgaitlhvaon-risinegds.steel wire rope. ·· 1M6imnimmudmia. bproelyakkienrgnmstarenntlegtrho:p2e2. kN. ·· TEexmtrpeomraerlyy aenadsyretuosianbsletaslly, slitgehmtwdeeisgihgnt e&d to preroavdiydetoaussaefe. anchorage to the multi-users at · tQhueicskamdiesmtimanetalisngw&orkrein-ign.stallation on a · Enqeuwipspieted twhiathnksspetociathl teeninsbiounilet rwthinactha.llows tensioning of · lDifeulrinabelebe&twheigehn stwtreonsgutphppoortlsy.mer casing. ·· HCaasrryainswg ihvaenl bdrleascsocmonpnleetcetowr iatthotneenseinodn ainnddicaasttoor.p knot · sInebcuuirletdshwoicthkparbosteocrptitvieonslmeeevcehaatnoisthmertoenlidm. it the · SimwpivaecltBfroarscsesCodnunriencgtofral-ldaerrseigsnt.ed to prevent any · tCwaibslteinhgaosf athsewroivpeel.snap hook to prevent twisting of the rope; this also includes an impact indicator. EN 795:2012 - Type C | TS 16415:2014 Type C FA 60 007 00 Horizontal Temporary Lifeline · Length: 2m -20m. · Minimum breaking strength: 23 kN. · 30mm wide polyester webbing. · Secures an operator throughout travel. · Forked ends in order to: Either anchor to a structure without the need to add anchorage sling, or hang directly on adapted anchorage point. · Steel ratchet to put the system into tension after adjusting the required length. · Supplied with 2 steel screw locking hooks. EN 795:2012 - Type C 44 f L 9.27 294.8 314.7 152.0 f L 193.2.17 Be Careful ! When installing the lifeline it is essential to take into account the deflection (f) of the lifeline that need to be add to the clearance of the fall arrest system used. OR OR 3.43 NEW FA 60 008 03 Beam Anchor Trolley · Aluminium & Stainless Steel material. · Suits beam width: 80 - 250mm. · Anchoring on D-ring, inner dia 55mm. · Strap length: 174mm. · Minimum breaking strength: 23 kN. EN 795:2012 - Type B FA 60 008 00 Beam Anchor FA 60 008 01 Beam Anchor · Aluminium & brass material. · Minimum breaking strength: 23 kN. · Designed to be installed on beams 70 - 150mm (FA 60 008 01). 100 - 330mm (FA 60 008 00). EN 795:2012 - Type B NEW COMING SOON SECTION 7 Anchorages FA 60 008 04 Dielectric Beam Anchor Trolley · Aluminium & Stainless Steel material. · Suits beam width: 80 - 250mm. · Anchoring on D-ring, inner dia 55mm. · Strap length: 174mm. 3.90 · Minimum breaking strength: 23 kN. 3.70 EN 795:2012 - Type B Lg FA 60 015 00 Door Anchor · Designed to be installed on frames from 60 - 125cm. · Can be used by 2 people at the same time. · Supplied with bag. · Minimum breaking strength: 20 kN. 3.90 EN 795:2012 - Type B 45 SECTION 7 Anchorages NEW FA 60 032 00 Container Anchor Post · Container Anchor Post is meant to provide a temporary anchor for working on top of 20ft & 40ft shipping containers. · In addition to being used as a stand alone anchor post, it can also be used to form a horizontal life line over the top of containers depending on the requirement of work to be done. · Comes with a side lock & tag line arrangement for secure installation by one person only. · Can be removed without damaging the container. · Has an anchorage allowing a 360° rotation. · Minimum breaking strength: 15 kN. · Height: 925mm. 14.53 EN 795:2012 - Type B FA 60 036 03 3 Hole Rigging Plate NEW FA 60 036 05 5 Hole Rigging Plate NEW · Designed to organize and provide multiple anchor points in multiple directions for superior varsatility. · Eye of the plate is capable to connect Karabiners having dia of 19mm. · Allows balancing the stress at the level of the head anchorage. · Minimum breaking strength: 45 kN. NFPA 1983 FA 60 028 14 Flange Anchor · Specifically designed to be fixed on walls, ceilings, roof tops or steel structures. · Ideal for use with an anchorage hook with large gate opening, such as the telescopic pole anchorage hook (FA 60 016 02 / FA 60 016 06). · Positioning through 2 fastenings 14mm (chemical or mechanical pins, stainless steel screw and nut system) in steel structure, or concrete. · Designed for use by one person at a time. · Minimum breaking strength: 23 kN. 0.31 EN 795:2012 - Type A NEW NEW FA 60 030 04 Tile Anchor · Can be installed on a wooden structure with the help of suitable fasteners (Zinc-plated woods screws, 8mm dia). · Permanentely installed beneath the tiles, stainless steel cable comes out for ease of use. · Lightweight, easy to install. · Minimum breaking strength: 15 kN. · Minimum section on wooden structure: 70x80mm. FA 60 034 00 Aluminium Anchor for Standing Seam Roof · Roof top anchor device is designed to be fixed on metal standing seams. · The U-profile allows installation on a multitude of different seams. · The 360° swivel anchorage eye on the top provides universal connection for the fall arrest system. · Easy to install (provided with 4 grub screws), it is the ideal anchorage point on standing seam roofs near areas where there is a risk of falling (Skydomes etc). 0.27 · Minimum breaking strength: 15 kN. 0.83 EN 795:2012 - Type A EN 795:2012 - Type A 46 SECTION 7 Anchorages FA 60 026 00 Edge Anchor · High Strength Aluminium Alloy material. · Allows multi-depth adjustment to suit varying roof cladding profiles. An optional large cladding insert allows fitting on to deeper roof profiles. · Can be fitted on steel cladding type roofs. · Designed for single user only. · Lightweight but robust, collapsible & portable for easy transport, storage and usage. · Having shock absorbing arm with fall indicator, it provides additional safety to the user while working. · Minimum breaking strength: 15 kN. EN 795:2012 - Type B allution FA 60 010 00 Wallution Parapet Anchor · Designed to be used in locations where a low parapet wall can host this anchor. · Can be installed on parapets with dimensions from 60 - 360mm. · Minimum breaking strength: 23 kN. EN 795:2012 - Type B NEW DESIGN Anchorage moved to top FA 60 027 10 10mm Flange Anchor · Stainless steel single anchor point, designed to be fixed on walls, ceilings, rooftops or steel structures. · Minimum breaking strength: 23 kN. FA 60 027 11 11mm Flange Anchor · Stainless steel single anchor point, designed to be fixed on walls, ceilings, rooftops or steel structures. · Minimum breaking strength: 23 kN. EN 795:2012 - Type A FA 60 012 00 Hinged Steel Roof Anchor · Designed to be mounted on a wooden frame by intermediate special nails. (80x80mm mini section - Resistance >1T). · Re-useable. · Forged D-ring. · Minimum breaking strength: 23 kN. 0.06 EN 795:1996 - Class A 355.0 265.0 229.0 276 577.5 3.0 9.6 1.05 47 SECTION 7 Anchorages 4 cm 34 cm FA 60 019 00 4cm Toggle Anchor · Designed to be installed on horizontal steel surface very quickly thanks to a pressure button that selects the fucntion "open" or "lock". · A hole of 21 to 30mm is required for installation. · Minimum breaking strength: 23 kN. FA 60 019 01 34cm Toggle Anchor · Designed to be installed on horizontal steel surface very quickly thanks to a pressure button that selects the fucntion "open" or "lock". · A hole of 21 to 30mm is required for installation. · Minimum breaking strength: 23 kN. EN 795:2012 - Type B EN 795:2012 - Type B FA 60 011 00 Stainless Steel Anchorage Point · Designed to be fixed with a chemical ankle. · Thread length: 115mm. · Dia: M12. · Minimum breaking strength: 23 kN. NEW DESIGN FA 60 014 00 Vertical Anchorage D-Bolt · Forged steel material. · Designed to be installed on vertical surfaces. · Thread length: 30mm. · Dia: M12. · Minimum breaking strength: 23 kN. 0.26 0.53 EN 795:2012 - Type A EN 795:2012 - Type A FA 60 018 00 InLock Concrete Anchor · Forged steel material. · Designed to be installed in concrete very quickly thanks to a pressure button that wedges the anchor point into the host structure. · Hole dia 18-19mm and of 110mm depth is needed for the installation into concrete. · Minimum breaking strength: 15 kN. EN 795:2012 - Type B 48 FA 60 029 05 Adjustable Anchorage Webbing Lanyard · Ideal for use with a lifeline. · To be installed on beam anchors, posts, large-sized structures. · 45mm wide polyester webbing. · Minimum breaking strength: 19 kN. · 5m (FA 60 029 05). · 10m (FA 60 029 10). 0.15 EN 795:2012 - Type B FA 60 005 08 Anchorage Webbing Sling · 20mm wide polyester webbing. · Minimum breaking strength: 30 kN. · 0.8m (Model: FA 60 005 08) Blue. · 1.2m (Model: FA 60 005 12) Yellow. · 1.5m (Model: FA 60 005 15) Red. · 3.0m (Model: FA 60 005 30) Grey. EN 795:2012 - Type B SECTION 7 Anchorages FA 60 004 15 Anchorage Webbing Sling · 44mm wide polyester webbing. · Minimum breaking strength: 30 kN. · Length: 1.5m. EN 795:2012 - Type B FA 60 006 20 Anchorage Steel Wire Rope Sling · Designed for use on structures with sharper edges. · Made of PVC coated 8mm galvanised wire rope. 0.56 · Minimum breaking strength: 23 kN. · 1m (FA 60 006 10). 0.15 · 2m (FA 60 006 20). 0.74 EN 795:2012 - Type B FA 60 017 15 Flame Resistant Anchorage Webbing Sling · 30mm wide polyester webbing. · Fire resistant webbing can withstand flames up to 371°C without any damage. · Forged alloy steel ring adjuster. · Maximum length: 1.50m. 0.57 EN 795:2012 - Type B 49 SECTION 7 Anchorages FA 60 016 05 Telescopic Pole Kit · Telescopic Pole Kit comprising of telescopic pole, the head of pole and the hanging hook. · Maximum length: 8m. · Minimum length: 2m. · Head length: 0.24m. · Pole and head of pole made of fibreglass. · Hanging hook made of alloy steel and moulded plastic. · Voltage resistance: 50kV. FA 60 016 02 Aluminium Anchorage Hook · Aluminium steel material. · Gate opening: 60mm. · Breaking strength: 23 kN. EN 795:2012 - Type B FA 60 016 06 Steel Anchorage Hook · Alloy steel material. · Gate opening: 95mm. · Breaking strength: 23 kN. EN 795:2012 - Type B 338.5 244.5 133.5 171.0 FA 60 016 01 Extension Section · Length: 1m. 50 Scan me and watch the Telescopic Pole application video on YouTube now! 0.425 SECTION 8 Rescue & Rope Access Q ES - L Q ift ES - NEW FA 70 100 20 Res-Q · This multi-functional device allows various applications like rescue, self evacuation, automatic controlled descent. · Designed in high strength Aluminium alloy, equipped with a Kernmantle rope (10.5mm dia) permanentely assembled to the system. Both termination ends of the rope are provided with textile loops for connections with hooks. · The device has 3 working modes: 1) Only Clockwise descent of rope. 2) Only Anti-clockwise descent of rope. 3) Both Clockwise and Anti-clockwise descent of rope. · Descent speed controlled at 0.9m/sec to 1.2m/sec. · Maximum height descent: 150m. · 20m (FA 70 100 20). · 50m (FA 70 100 50). · 100m (FA 70 100 100). EN 341:2011 NEW FA 70 200 20 Lift Res-Q · This unique device is an ideal piece of equipment for use in rescue and retrieval thanks to the integrated rescue winch. · Designed in high strength Aluminium alloy, equipped with a Kernmantle rope (10.5mm dia) permanentely assembled to the system. Both termination ends of the rope are provided with textile loops for connections with hooks. · The device has 3 working modes: 1) Only Clockwise descent of rope. 2) Only Anti-clockwise descent of rope. 3) Both Clockwise and Anti-clockwise descent of rope. 4) Rescue hoisting function thanks to the wheel with self-blocking ascending feature. · Descent speed controlled at 1.1m/sec. · Maximum height descent: 150m. · Maximum hoisting height: 75m. · 20m (FA 70 200 20). · 50m (FA 70 200 50). · 100m (FA 70 200 100). EN 341:2011 | EN 1496 - Class B FA 70 004 00 Figure of 8 · Aluminium Alloy, black anodized finish. · Manual descender for self evacuation. · Works on 9-11mm dia Kernmantle rope. · Inner dia: 52mm and 26mm. · Height: 145mm. · Minimum breaking strength: 50 kN. FA 70 001 00 Grip Descender · Aluminium Alloy, black anodized finish. · Ideal for descent on a single rope. · Equipped with a unique self braking system which initiates the brake as soon as the handle is released, or clasped too tightly. · Works on 10.5-12mm dia Kernmantle rope. · Maximum speed: 2m/s. 0.12 EN 341 - Class A FA 70 021 00 Descender · Aluminium Alloy, black anodized finish. · Can be used for both ascent and descent on a single rope. · Equipped with a unique self braking system which initiates the brake as soon as the handle is released, or clasped too tightly. · Works on 10-12mm dia Kernmantle rope. · Maximum speed: 2m/s. 0.35 0.35 EN 341 - Class 2B | EN12 841 - Type C 51 SECTION 8 Rescue & Rope Access FA 70 002 00 Left Hand Ascender Handle · Aluminium Alloy, black anodized finish. · Designed for rope climbing, locks with one hand for comfortable use. · Works on 10-12mm dia Kernmantle rope. EN 567 FA 70 008 00 Single Aluminium Pulley · Aluminium alloy, green anodized finish. · For use on 12mm dia kernmantle rope. · Minimum breaking strength: 18 kN. 18 kN 9 kN 9 kN FA 70 003 00 Right Hand Ascender Handle · Aluminium Alloy, green anodized finish. · Designed for rope climbing, locks with one hand for comfortable use. · Works on 10-12mm dia Kernmantle rope. 0.22 EN 567 FA 70 015 00 Ventral Rope Clamp · Aluminium body, black finish. · To be used in combination with an ascender handle to allow ascent on a rope when double rope working. · Ergonomic opening mechanism allowing manipulation with one hand. · Attachment eye ideally positioned for easy connection on the harness. · Works on 10-12mm dia Kernmantle rope. 0.22 0.16 EN 567 FA 70 016 00 Simple Pulley with Moveable Flange FA 70 017 00 Double Pulley with Moveable Flanges · Aluminium body, black anodized finish. · For use on 9-16mm dia kernmantle rope. · Aluminium sheave, mounted with dry bearings. · Minimum breaking strength: 40 kN. · Workload: 10 kN. · FA 70 016 01: Stainless steel sheave mounted with ball bearings. · Aluminium body, black anodized finish. · For use on 9-16mm dia kernmantle rope. · Aluminium sheave, mounted with dry bearings. · Minimum breaking strength: 40 kN. · Workload: 10 kN. · FA 70 017 01: Stainless steel sheave mounted with ball bearings. 0.08 0.27 0.49 EN 12278 Certified by International Climbing And Mountaineering Federation EN 12278 Certified by International Climbing And Mountaineering Federation FA 70 022 00 Simple Pulley with Moveable Flanges · Pulley for multipurpose use. · Aluminium body, black finish. · For use on 9-16mm dia kernmantle rope. · Aluminium sheave, mounted with dry bearings. · Minimum breaking strength: 40 kN. · Workload: 10 kN. · FA 70 022 01: Stainless steel sheave mounted with ball bearings. EN 12278 0.14 Certified by International Climbing And Mountaineering Federation FA 70 023 01 Double Tandem Pulley (small) · Pulley for multipurpose use. · Aluminium body, silver finish. · For use on 9-12mm dia kernmantle rope. · Stainless steel sheaves, mounted with ball bearings. · Minimum breaking strength: 45 kN. · Workload: 10 kN. EN 12278 0.33 Certified by International Climbing And Mountaineering Federation FA 70 024 01 Double Tandem Pulley (large) · Pulley for multipurpose use. · Aluminium body, silver finish. · For use on 9-16mm dia kernmantle rope. · Stainless steel sheaves, mounted with ball bearings. · Minimum breaking strength: 45 kN. · Workload: 10 kN. EN 12278 0.79 Certified by International Climbing And Mountaineering Federation 52 SECTION 8 Rescue & Rope Access FA 70 005 00 Evacuation Triangle · To be used for rescue of injured personnel. · Contains 3 metallic D-rings at attachment elements. · Dorsal D-ring for the guiding of the evacuation. · Shoulder straps made of elastic webbing, automatic buckles. · 5 buckles for size adjustment. · Size: Universal. EN 1498 - Class B FA 70 006 00 Easy Seat · Ergonomic, comfortable working chair with aluminium reinforcement inside. · Is an accessory to a suspension harness (having a ventral D-ring). · Fully adjustable, equipped with 3 loops for easy attachment of karabiners and other accessories and 1 loop for attachment to the belt of the harness when the seat is not in use. · 44mm wide polyester webbing. · High Strength Steel components. · Minimum breaking strength: 23 kN. 1.09 1.60 EN 1498 - Class B 57.2 FA 50 219 14B Aluminium Quarter Turn Locking Karabiner · Aluminium steel material. · Gate opening: 14mm. · Breaking strength: 23 kN. · Symmetrical oval shape. 109.7 EN 362:2004 - Class B FA 70 014 00 Asymetric `Y' Lanyard · Intended to be used with an ascender handle for easy movement on rope, especially for splits passage thanks to the 2 strands (short and long). · 12mm dia. polyamide kernmantle. · 3 loops protected by an abrasion resistant tubular webbing. · Short strand: 0.4m. · Long strand: 0.8m. EN 354:2010 FA 70 019 00 Rescue Strap · To be used for rescue of injured personnel. 0.10 EN 1498 - Class A FA 70 013 00 Pedal Foot Loop · Intended to be fixed on ascender handle to allow on a rope when working on double rope. · 45mm polyester webbing. · Sliding protective sleeve for the foot. · Easy length adjustment by a non-opening buckle. · Loop protected by an abrasion resistant tubular webbing. · Length: 1m to 1.5m. 0.17 FA 90 004 00 Opening Protective Sleeve · Designed to protect ropes against abrasion due to friction. · Made in resistant PVC, flexible and opening (closing) by Velcro tape), fitted with a sling at one end for a quick and easy attachment. · Length: 0.55m. 0.20 0.05 FA 70 010 99 Semi-static Kernmantle Rope · Polyamide material. · Available in various lengths on request. · Standard length: 200m. · Maximum roll size: 300m. · FA 70 010 99: 10.5mm dia. · FA 70 011 99: 11mm dia. · FA 70 012 99: 12mm dia. 0.24 EN 1891 53 SECTION 8 Rescue & Rope Access FA 70 018 00 Stretcher · Light stretcher, ideal for evacuations. · Once the person is installed safely, the stretcher becomes rigid. · Can be used vertically and horizontally. · Can be stored in a compact bag for easy carrying. · Polypropylene material. · Polyamide straps. · 2 carrying handles on each side. · Maximum weight: 200kg. Maximum load Weight of device Total weight with bag and belts Loading Surface Length Width Material Hooks (Material) Rope Length Diameter Handles Material Number of handles on every longitudinal side 200Kg 5.5Kg 8Kg 2.5 M 0.9 M High Strength Polymer Alloy Steel 9 m Dia 10mm Polyester 2 Stretcher Bag included FA 70 007 01 Spreader Bar · Is available as an optional extra to the Bosun's Chair. FA 70 020 00 Telescopic Rescue Pole · Material: Fiber glass. · Provided with storage bag. · Minimum length: 0.75m. · Maximum length: 3.5m. 54 1.00 FA 70 007 00 Bosun's Chair · Ergonomic and comfortable working chair. · For vertical ascent and descent. · Size: Universal. · Spreader bar (FA 70 007 01) Available as an optional extra (not included as standard). 1.00 3.32 EN 1498 - Class B SECTION 8 Rescue & Rope Access FA 70 027 20 Universal Kit for Manual Evacuation + + + · FA 70 021 00 Descender. · FA 70 010 99 20m Semi-static rope, 10.5mm dia. · FA 60 005 15 (2pcs) Anchorage Webbing Slings 1.5m. · FA 50 302 22B (4pcs) Aluminium triple action locking karabiner (keylock version). · FA 70 900 30 Guiding kernmantle rope 30m, 6mm dia. · FA 70 015 00 (2pcs) Ventral rope clamp. · FA 70 010 99 5m Semi-static rope, 10.5mm dia. · FA 70 017 00 (2pcs) Double pulley with moveable flanges, double attachment. · FA 50 400 10 Oval quick link, 10mm gate opening. · FA 50 401 10 Delta quick link, 10mm gate opening. · FA 90 106 00 Cylindrical bag for the storage and carrying of the kit. FA 70 021 00 FA 50 302 22B FA 50 302 22B x 2 FA 50 302 22B FA 70 010 99 (20m) FA 60 005 15 x 2 FA 70 900 30 FA 50 400 10 FA 70 015 00 x 2 FA 70 010 99 (5m) FA 70 008 02 x 2 FA 90 106 00 FA 50 401 10 FA 70 027 20 Self Evacuation Kit · FA 70 021 00 Descender. · FA 70 010 99 20m Semi-static rope, 10.5mm dia. · FA 70 005 00 Rescue Triangle. · FA 50 302 22B (4pcs) Aluminium triple action locking karabiner (keylock version). · FA 60 005 15 (2pcs) Anchorage webbing sling 1.5m. · FA 90 106 00 Cylindrical bag for the storage and carrying of the kit. FA 70 021 00 + + FA 50 302 22B FA 70 010 99 (20m) FA 70 005 00 FA 50 302 22B x 4 FA 60 005 15 x 2 FA 90 106 00 55 SECTION 9 Head Protection NEW HP 10 200 00X FOX Safety Helmet · Recommended for mountaineering, maintenance and rescue operations as well as for works at height where the risk of falling is high. · Thermoformed inner shell. · Adjustable chinstrap. · 10 ventilation slots for better comfort. · Ratchet headband, suitable for head circumferences from 52 to 61cm. · Slots for visor fitting (HP 10 200 01 See below). · Small hooks for headlamp, side slots for hearing protection fitting (accessories not included). · Chinstrap breaking strength: 50 daN. EN 12492:2012 NEW HP 10 200 01 Helmet Visor · Clear visor. · Very easy to install. · Fastening accessories included. 56 HP 10 200 00B HP 10 200 00W HP 10 200 00R HP 10 200 00O SECTION 10 Revolta Product Range A range of Harnesses & Lanyards specially designed for workers engaged in "besmearing" industries. Ideal for use in: a variety of applications including petrochemical, painting,water treatment, food processing, offshores, general industry... Significant features: · Oil and dirt repellent webbing provides excellent resistance from build up of oil and dirt. · Highly UV resistant. · Deflects the dust, dirt or any unwanted material causing abrasion, which makes it tear and cut resistant. · Easy to care for, wipes clean in seconds. · Increased durability and longevity. FA 30 309 20 Shock Absorbing Webbing Lanyard · Shock absorber which reduces the impact of the fall to less than 6 kN. · Protective 45mm wide polyester elasticated webbing with oil and dirt repellent coating. · Aluminium snap hook & rebar hook. · Loops protected by an abrasion resistant tubular webbing. · Relaxed length: 1.5m. · Expanded length: 2.0m. EN 355:2002 FA 10 113 00 2 Point Full Body Harness · Adjustable shoulder and thigh straps. · Oil & dirt repellent REVOLTA webbing. · Shoulder straps have combination buckles. · Soft padding on thigh straps for extended comfort. · Covered identification labels. · S-L (FA 10 113 00). · L-XXL (FA 10 113 01). EN 361:2002 2019 FA 30 406 20 `Y' Forked Shock Absorbing Webbing Lanyard · Shock absorber which reduces the impact of the fall to less than 6 kN. · Protective 45mm wide polyester elasticated webbing with oil and dirt repellent coating. · Aluminium snap hook & rebar hook. · Loops protected by an abrasion resistant tubular webbing. · Relaxed length: 1.4m. 1.47 · Expanded length: 2.0m. EN 355:2002 FA 10 214 00 4 Point Full Body Harness · 2 bended D-rings on belt. · Adjustable shoulder, thigh straps and waist belt. · Oil & dirt repellent REVOLTA webbing. · Shoulder straps have combination buckles. · Soft padding on thigh straps for extended comfort. · Covered identification labels. · S-L (FA 10 214 00). · L-XXL (FA 10 214 01). EN 361:2002 | EN 358:2000 2019 FA 40 907 20 Adjustable Work Positioning Lanyard · Shock absorber which reduces the impact of the fall to less than 6 kN. · Protective 45mm wide polyester elasticated webbing with oil and dirt repellent coating. · Aluminium snap hook & rebar hook. · Loops protected by an abrasion resistant tubular webbing. · Relaxed length: 1.4m. 2.30 · Expanded length: 2.0m. EN 358:1999 1.68 1.80 0.73 57 SECTION 11 Dielectri Product Range FA 10 212 00 4 Point Full Body Harness · Specially designed for conditions with electrical hazards. · Special polymer coated D-rings and all metal adjustment buckles making it completely electrically insulated. · Shoulder straps are elasticated to provide flexibility and snug fitting. · Covered identification labels. · Universal (FA 10 212 00). EN 361:2002 | EN358:2000 FA 60 016 05 Telescopic Pole Set · See Page 50 for product information The Dielectri range was designed to protect operators working in an environment with potential electric hazards. This range allows the wearer to be protected against an accidental contact with a current (in combination with appropriate equipment: gloves, helmet, shoes/boots, clothes etc...). All the metal parts are electrically insulated thanks to a special polymer that can withstand a maximal voltage of 14 kV. 2.75 FA 60 008 04 Telescopic Pole Set · See Page 50 for product information FA 50 222 55 Dielectric Scaffold Hook · Steel with polymer composite. · Minimum voltage resistance: 14 kV. · Gate opening: 55mm. · Breaking strength: 23 kN. EN 362:2004 - Class T 120.3 242.8 FA 30 307 20 Shock Absorbing Webbing Lanyard · 30mm wide polyester webbing. · 44mm wide shock absorber. Shock absorber reduces the impact of the fall to less than 6 kN. · Also available with snap hook at end instead of textile loop (FA 30 308 20). · Length: 1.8m. EN 355:2002 FA 50 223 15 Dielectric Snap Hook · Steel with polymer composite. · Minimum voltage resistance: 14 kV. · Gate opening: 55mm. · Breaking strength: 23 kN. EN 362:2004 - Class T 58 164.8 FA 30 404 15 `Y' Forked Shock Absorbing Webbing Lanyard · 30mm wide polyester webbing. · 44mm wide shock absorber. Shock absorber reduces the impact of the fall to less than 6 kN. · Also available with snap hook at end instead of textile loop (FA 30 405 15). 69.5 · Length: 1.5m. EN 355:2002 SECTION 12 ATEX Free Blast Product Range In ATEX hazardous areas (Potentially Explosive Atmospheres), a spark from mechanical, electric, electrostatic origin etc., may ignite an inflammable gas, vapour or mist mixture and an explosion may occur. Hence the importance of risk assessment. If this assessment reveals that wearing protective equipment against falls from heights is necessary in ATEX area, they must be in accordance with Atex Directive 94/9/EC. Our entire range can be used in zone 1, it conforms to Atex Directive 94/9/EC, and standards EN13463-1:2003 and EN13463-5:2003. The webbing is also tested in accordance with EN 1149-1:2006. FA 10 109 00 2 Point Full Body Harness · Specially designed for conditions with explosive atmospheres. Suitable for petrochemicals, mining industry etc. · Adjustable shoulder & thigh straps. · Combination buckles. · Fitted sit-strap for extended comfort. · Stainless steel buckles for excellent corrosion protection. Antistatic webbing prevents the risk of an elecrostatic discharge igniting. · Universal (FA 10 109 00). 1.19 EN 361:2002 | EN1149-1:2006 | EN13463-1:2001 | EN13463-5:2003 FA 20 402 10 B Helixon Retractable Fall Arrester · Casing made up of high impact strength polymer, to prevent breakage and is nearly indestructible. · Comes with glavanized steel wire rope of 4.5mm dia. · steel karabiner at anchorage end, swil snap hook with load indicator at attachment end. · Minimum breaking strength: 12 kN. · 10m (FA 20 402 10 B). · 15m (FA 20 402 15). EN 360:2002 FA 30 306 20 Shock Absorbing Atex Lanyard · 45mm wide polyester webbing. · Shock absorber which reduces the impact of a fall to less than 6 kN. · Fitted with aluminium scaffold hook one end and aluminium karabiner at the other end. · 2.0m (FA 30 306 20). 0.94 EN 355:2002 FA 50 103 22 Aluminium Screw Locking Karabiner · Aluminium steel material. · Gate opening: 22.5mm. · Breaking strength: 23 kN. · Keylock version: FA 50 103 22B. EN 362:2004 - Class B Additional items 69.0 FA 30 403 15 `Y' Forked Shock Absorbing Atex Lanyard 111.0 · 45mm wide polyester webbing. · Shock absorber which reduces the impact Ø11.0 of a fall to less than 6 kN. · Fitted with aluminium scaffold hooks one end and aluminium karabiner at the other end. · 1.5m (FA 30 306 20). 1.49 EN 355:2002 FA 20 401 10/20/30 Page 18 KS 7000 Page 27 KS 8000 Page 28 KS 9000 Page 29 FA 60 001/002 00 Page 42 FA 60 003 20/30 Page 43 59 SECTION 13 Fire Free Product Range FA 30 305 10 · 45mm wide polyester webbing. · Reduces the impact of a fall to less than 6 kN. · 1.0m: (FA 30 305 10). · 1.5m: (FA 30 305 15). · 2.0m: (FA 30 305 20). FENA35350:2040202 10 · 45mm wide polyester webbing. · Reduces the impact of a fall to less than 6 kN. · 1.0m: (FA 30 402 10). · 1.5m: (FA 30 402 15). EN 355:2002 FA 40 400 15 Y Forked Restraint Lanyard · 45mm wide polyester webbing. · Breaking strength: 22 kN. · Length: 1.5m. EN 354:2002 FA 60 017 15 Anchorage Lanyard · 45mm wide polyester webbing. · Breaking strength: 22 kN. · Length: 1.5m. EN 795:2012 - Type B FA 40 905 20 Work Positioning Lanyard · 30mm wide polyester webbing. · Forged alloy steel ring adjuster. · Length: 2m max. EN 358:2000 60 Sparks, molten metal splashes during welding, grinding, can quickly damage polyamide or polyester typically used in the construction of standard harnesses, lanyards, shock absorbers etc. Our complete Fire Free range includes anchorage lanyards, fall arrest systems, lanyards, harnesses, all designed with specific webbing. It provides comprehensive protection to users working at height in this particular type of environment. The straps of this range were tested in static resistance after exposures to splashes of molten metal and can have the following certifications: ISO 9150:1988, ISO 15025:2002. This webbing can withstand temperatures up to 371°C without any damage. FA 10 110 00 2 Point Flame Resistant Full Body Harness · 2 chest attachment textile loops and a forged steel Dorsal D-ring. · Adjustable shoulder and thigh straps. · Automatic buckles. · Static strength of harness webbing has been tested after exposure to molten metal splashes. · Universal (FA 10 110 00). 1.79 EN 361:2002 FA 10 211 00 2 Point Flame Resistant Full Body Harness · 2 chest attachment textile loops and a forged steel Dorsal D-ring. 2 lateral D-rings at waist level. · Adjustable shoulder and thigh straps. · Automatic buckles. · Static strength of harness webbing has been tested after exposure to molten metal splashes. · Universal (FA 10 110 00). 2.55 EN 361:2002 | EN358:2000 SECTION 14 ANSI Product Range FAP15501D 3 Point Full Body Harness FAP15503G 5 Point Full Body Harness ANSI: American National Standard Institute Kratos Safety offers a comprehensive range of PPE against falls from height, in accordance with ANSI* Z359.1-2007 and/or Z 359.13-2009 standards. This new range allows you to answer to requests from specific markets (technical or geographical requirements), where ANSI standards are mostly used. Please contact our sales office for further informations or requests concerning PPE equipment with ANSI compliance. FAP3118(6) Shock Absorbing Webbing Lanyard ANSI Z 359.1-2007 PN 113 A Steel Quarter TurnLocking Karabiner PN 146 Steel Snap Hook FAP30199(6) `Y' Forked Shock Absorbing Webbing Lanyard ANSI Z 359.13-2009 Self Retractable Lifeline PCGS10FT PCGS25FT PCGS50FT ANSI Z 359.12-2009 Vertical Life Line VLL 25FT VLL 50FT ANSI Z 359.1 & OSHA Compliant Hinged Steel Roof Anchor SA01 Stainless Steel Roof Anchor SA02 Parapet Anchor SA11 ANSI Z 359.14-2012 & OSHA Compliant ANSI Z 359.1 & OSHA Compliant 61 SECTION 15 Load Arresters LA 10 1000 11 Load Arresters The cable load arresters are used to stop the falling of a load (basketball hoop, ramp lighting, industrial machines etc...) for a short distance in case of: · A break of chain or cable for hoisting the load. · A failure of the retaining elements of the load. · Load arresters designed to stop the fall of a load with a maximum weight of 1000kg. · Casings made up of Steel. · Galvanised Steel Wire Rope 8mm dia. · Multi-ratchet quick fall arrest system. · Integrated shock absorber, which reduces the efforts on the structure. · Reduced fall arrest distance. · Intensive number of cycles. Ref LA 10 1000 11 Length Weight 23.0 kg Load Capacity 1000kg Machinery Directive 2006/42/CE 114.6 250.0 208.6 450 350.0 530 530 LA 10 250 10 Load Arresters The cable load arresters are used to stop the falling of a load (basketball hoop, ramp lighting, industrial machines etc...) for a short distance in case of: · A break of chain or cable for hoisting the load. · A failure of the retaining elements of the load. · Load arresters designed to stop the fall of a load with a weight between 250kg and 500kg. · Casings made up of high impact strength Polymer, nearly indestructible, to prevent breakage. · Galvanized steel wire rope. · Multi-ratchet quick fall arrest system. · Integrated shock absorber, which reduces the efforts on the structure. · Reduced fall arrest distance. · Maximum 60 cycles per day. Ref LA 10 250 10 LA 10 300 10 LA 10 300 15 LA 10 400 10 LA 10 400 20 LA 10 500 10 LA 10 500 15 Length Weight 4.15kg 5.5kg 6.0kg 11.5kg 12.95kg 11.65kg 12.20kg Load Capacity Wire Rope Diam. 250kg 300kg 400kg 500kg 6.0 m LA 10 250 10 LA 10 300 10 LA 10 400 10 LA 10 500 10 172 223 104.0 104.0 Machinery Directive 2006/42/CE 62 FA 90 104 00 Large Storage Bag · Storage bag and tool holders in Oxford polyester. · Multi-pocket, 18 internal pockets and 19 external pockets, external loops for long tool. Opening system "hold-open", closure by zip. · Reinforced bottom, carrying strap and carrying handle. · Dimensions: 620 x 240 x 300mm. · Total capacity: 44 litres. FA 90 106 00 Large Cylindrical PVC Backpack · Multi use cylindrical PVC backpack. · Two inside pockets & 16 loops to attach accessories. · Padded shoulder straps, with reflective strips. · Closure with pull-cord blocker & covered by hood. · Reflective stripe on the front side. · Transparent document window with zipper. · Dimensions: 620 x 350mm. · Total capacity: 58 litres. NEW DESIGN COMING SOON FA 90 103 00 Large Kit Bag · Oxford polyester. · Rigid base in polyethylene. · Transparent window [COMING SOON]. · Dimensions: 600 x 190 x 260mm. · Total capacity: 29 litres. FA RUCKSACK Rucksack · 3 zip compartment. · Dimensions: 470 x 300 x 140mm. · Total capacity: 19 litres. SECTION 16 Kit Bags & Rucksacks FA 90 101 00 Multi-pocket Backpack · Storage bag and tool holders in Oxford polyester. · 3 pockets & 3 tool keepers. · Padded back, shoulder and bottom, carrying handle. · Dimensions: 450 x 360 x 180mm. · Total capacity: 26 litres. FA 90 105 00 Cylindrical PVC Backpack · Multi use cylindrical PVC backpack. · Inside pockets and loops to attach accessories. · Carrying handle on one side, closure with pull-cord blocker and covered by hood. · Dimensions: 290 x 620mm. · Total capacity: 41 litres. NEW DESIGN COMING SOON FA 90 102 00 Kit Bag · Oxford polyester. · Rigid base in polyethylene. · Transparent window [COMING SOON]. · Dimensions: 410 x 230 x 260mm. · Total capacity: 24 litres. FA KIT BAG Drawstring Kit Bag · Nylon drawstring bag. 63 SECTION 16 Kit Bags & Rucksacks FA 90 108 00 Tripod Bag · Bag suits the Kratos Safety Confined Space Tripods. · Dimensions: 1430 x 320 x 350mm. · Total capacity: 160 litres. NEW FA 90 100 00 Handle Carrier Kit Bag · Oxford polyester. · Rigid base in polyethylene. · Dimensions: 600 x 190 x 260mm. · Total capacity: 29 litres. NEW FA 90 115 00 Storage Bag · Storage bag and tool holders in Oxford polyester. · Padded back. · Dimensions: 260 x 120 x 400mm. · Total capacity: 12 litres. FA 90 107 00 Multi Use Cylindrical PVC Backpack · One pocket inside. · Loops to attach accessories. · Carrying handle on one side, closure with pull-cord blocker. · Dimensions: 620 x 320mm. · Total capacity: 49 litres. NEW FA 90 131 18 Jute Bag · Complete with 2 handles. · Ergonomic carrying strap. · Dimensions: 450 x 150 x 320mm. · Total capacity: 30 litres. COMNINEGWSOON FA 90 116 00 Extra Large Kit Bag · Oxford polyester. · Rigid base in polyethylene. · Transparent window [COMING SOON]. · Dimensions: 530 x 280 x 270mm. · Total capacity: 40 litres. 64 SECTION 17 Harness Kits · FA 10 108 00 - Single point comfort harness. · FA 30 304 18 - 1.8m shock absorbing webbing lanyard. · FA ES 3116 - Environmental friendly carry bag. FA KIT 1 - Single Point Scaffold Kit · FA 10 108 00 - Single point comfort harness. · FA 40 902 20 - 2.0m work positioning rope lanyard. · FA ES 3116 - Environmental friendly carry bag. FA KIT 2 - Single Point Restraint Kit · FA 10 102 00 - Single point harness. · FA 30 304 18 - 1.8m shock absorbing webbing lanyard. · FA ES 3116 - Environmental friendly carry bag. FA KIT 3 - Single Point Standard Kit · FA 10 101 00/01 - 2 point luxury full body harness. · FA 30 502 15 - 1.5m shock absorbing rope lanyard. · FA 40 902 20 - 2.0m work positioning rope lanyard. · FA 50 101 17 - Alloy steel karabiner. · FA 10 901 00 - Suspension trauma strap. · FA RUCKSACK / FA 90 102 00 - Rucksack / Kit bag. FA KIT 4 - 2 Point Premium Kit · FA 10 105 00 - 2 point comfort harness. · FA 30 304 18 - 1.8m shock absorbing webbing lanyard. · FA RUCKSACK / FA 90 102 00 - Rucksack / Kit bag. FA KIT 5 - 2 Point Scaffold Kit · FA 10 105 00 - 2 point comfort harness. · FA 40 901 20 - 2.0m work positioning webbing lanyard. · FA RUCKSACK / FA 90 102 00 - Rucksack / Kit bag. FA KIT 6 - 2 Point Restraint Kit 65 SECTION 17 Harness Kits · FA 10 105 00 - 2 point comfort harness. · FA 40 902 20 - 2.0m work positioning rope lanyard. · FA RUCKSACK / FA 90 102 00 - Rucksack / Kit bag. FA KIT 7 - 2 Point Restraint Kit · FA 10 302 00 - 2 point high visibility comfort harness. · FA 40 901 20 - 2.0m work positioning webbing lanyard. · FA RUCKSACK / FA 90 102 00 - Rucksack / Kit bag. FA KIT 9 - 2 Point Hi-Viz Restraint Kit · FA 10 111 00/01 - 3 point comfort harness. · FA 30 304 18 - 1.8m shock absorbing webbing lanyard. · FA RUCKSACK / FA 90 102 00 - Rucksack / Kit bag. FA KIT 10 - 3 Point Scaffold Kit · FA 10 111 00/01 - 3 point comfort harness. · FA 40 901 20 - 2.0m work positioning webbing lanyard. · FA RUCKSACK / FA 90 102 00 - Rucksack / Kit bag. FA KIT 11 - 3 Point Restraint Kit · FA 10 103 00 - 2 point standard harness. · FA 40 900 20 - 2.0m work positioning twisted rope lanyard. · FA KITBAG - Drawstring bag. FA KIT 19 - 2 Point Basic Restraint Kit 66 SECTION 18 Training & Servicing Inspection/Service/Repair We can support the inspection and examination of all Kratos Safety items in line with current legislation through a fully approved network of personnel within the UK. Giving full written details of our findings in line with the legislative requirements and clearly outlining if the product is fit for ongoing use. This information would also include any suggested recommendations and options to maintain the equipment correctly. We carry a large stock of spare parts to ensure we can assist with the full service package for all Kratos Safety Fall Arrest Blocks. This includes: complete strip down, recalibration of the braking system and other repairs if required. This can be carried out by oursevles or any of our approved services agents. Training GT have been authorised by Kratos Safety to fully support training courses in the UK and overseas. With our authorised trainer agreements we are able to offer all customers the knowledge and skills required to enable them to assist their clients with all their servicing needs. We currently offer different courses to suit the clients needs. The inspectors course gives the successful candidate the ability to inspect and re-certify all Kratos Safety equipment in line with European regulations EN 365:2004. The full service engineers course offers the candidate an opportunity to become certified to service all Kratos Safety fall arrest blocks under their responsibility. This in turn creates a full service agent of Kratos Safety Equipment. 67 www.gtlifting.co.uk www.kratossafety.co.uk George Taylor & Co Lifting Gear (Midlands) Ltd Head Office Unit 4, Fryers Road, Walsall, WS2 7LZ UK T +44 (0)1922 490220 F +44 (0)1922 490229 E office@gtlifting.co.uk Scottish Distribution Centre 9 Haddow Street, Hamilton, Lanarkshire ML3 7HX UK T +44 (0)1698 283561 F +44 (0)1698 457914 E office@gtlifting.co.uk George Taylor & Co (ME) FZC, R.A.K. Free Trade Zone, PO BOX 50019, Ras Al Khaimah, United Arab Emirates T +971 (0)7 2660041 F +971 (0)7 2660212 E gtliftng@emirates.net.ae GT General Trading LLC, PO BOX 50019, Ras Al Khaimah, United Arab Emirates E mohammed.sherief@gt-trading.aeAdobe PDF library 15.00 Adobe Illustrator CC 2017 (Macintosh)