BISSELL CleanView® Compact Turbo Upright Vacuum

Product Overview

Key components of your BISSELL CleanView® Compact Turbo Upright Vacuum:

1. Extension Wand
2. TurboBrush® Tool
3. Crevice Tool
4. Tank Release Button
5. Dirt Tank
6. Dirt Tank Empty Button
7. Handle Recline Pedal
8. Extension Wand Release
9. Dusting Brush
10. Stretch Hose
11. Power Cord
12. Power Switch Pedal
13. Height Adjustment Knob

Important Safety Instructions

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

• Always connect to a polarized outlet (one slot is wider than the other). Do not modify the plug.
• Unplug when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Close attention is necessary when used by or near children; do not allow to be used as a toy.
• Use only manufacturer's recommended attachments.
• Do not use with a damaged cord or plug. Have it repaired at an authorized service center if not working correctly, or if dropped, damaged, left outdoors, or dropped into water.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord; grasp the plug.
• Do not handle plug or vacuum cleaner with wet hands.
• Keep openings free of dust, lint, hair, and anything that may reduce air flow. Do not put any object into openings.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn OFF all controls before plugging or unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
• Do not use in enclosed spaces filled with vapors from oil-based paint, paint thinner, moth-proofing substances, flammable dust, or other explosive or toxic vapors.
• Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without filters in place.
• Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
• Use only on dry, indoor surfaces.
• Keep appliance on a level surface.
• Do not carry the vacuum cleaner while it is running.
• Unplug before connecting or disconnecting the TurboBrush® Tool.
• Plastic film can be dangerous; keep away from children to avoid suffocation.
• Do not plug in until familiar with all instructions and operating procedures.
• When finished, wrap cord around cord wrap for storage. Store unit indoors in a dry location.
• Any other maintenance or servicing should be performed by an authorized service representative.

COMMERCIAL USE OF THIS UNIT VOIDS THE MANUFACTURER'S WARRANTY.

Polarized Plug: This appliance has a polarized plug (one blade is wider than the other) for safety. It fits in a polarized outlet only one way. If the plug does not fit fully, reverse it. If it still does not fit, contact a qualified electrician. Do not change the plug.

SAVE THESE INSTRUCTIONS. THIS MODEL IS FOR HOUSEHOLD USE ONLY.

What's in the Box?

Standard accessories may vary by model. Refer to the "Carton Contents" list on the carton top flap for your specific purchase.

Typically includes:

• Upper Handle
• Base Unit
• TurboBrush® Tool
• TurboBrush® Tool Holder
• Crevice Tool
• Dusting Brush

Assembly

For assembly videos, visit support.BISSELL.com.

1. Insert the handle into the base unit with the tab facing the back of the vacuum. Push down until it clicks.
2. Wrap the power cord around the upper and lower cord wraps.
3. Attach the TurboBrush® tool holder to the handle by lining up the hole with the indent on the handle. Attach tools by inserting them onto the on-unit tool holders.

Using Your Vacuum

1. Step on the recline pedal and pull the handle back towards you.
   Note: To maneuver under furniture, step and hold the pedal to further recline the machine.
2. Connect the power cord plug to a polarized outlet.
3. Press the red power button [Power Button] with your foot to turn the vacuum ON.
4. Turn the dial on the foot to the desired height setting.
   Tip: For best performance, adjust to the lowest practical setting. If your vacuum is difficult to push, adjust to the next higher setting.
5. To turn the machine OFF [Power Off], step on the power switch pedal. Once finished, loop the power cord around the cord wraps and clip it to secure.

Note: Some Berber carpets may fuzz with wear. Repeated strokes in the same area may enhance this condition.

WARNING: Before using your vacuum, ensure the dirt tank is locked in position and all filters (pre and post-filters) are in place. DO NOT operate your vacuum without these filters.

Cleaning Above Floors

For additional support videos and information, visit support.BISSELL.com.

1. Raise the handle to the upright position.
2. Grasp the hose and pull it up to remove it from the hose holder.
3. For extended reach, remove the extension wand by pressing the release lever and pulling the handle out of the body.
4. Insert the hose into the extension wand and twist to lock. Attach the desired tool by pushing it onto the hose or extension wand.

Note: The brush roll will continue to rotate while using your vacuum for above-floor cleaning. To prevent carpet damage, do not lean on the vacuum or let the power foot tilt forward.

Emptying and Cleaning the Dirt Tank

For additional support videos and information, visit support.BISSELL.com.

1. To remove the dirt tank, push the release button on top of the tank handle.
2. Hold the dirt tank over a garbage bin and press the release button to empty. Snap the bottom back into place.
3. Open the dirt tank lid by lifting the release latch.
4. Remove the primary separator by lifting it out of the dirt tank. The tank and separator can be hand-washed with warm water and mild detergent. Rinse well and let air dry completely. Not dishwasher safe.
5. Remove the hose by twisting to unlock and pulling it up. Check for clogs before reassembling.

Cleaning the Filter

1. Push the dirt tank release button on top of the tank handle to remove the tank. Open the lid by lifting the release latch. The filter is located inside the dirt tank lid.
2. Pull the filter to remove it. Hand wash with warm water and mild detergent. Let dry for 24 hours.
   Note: Replace the filter if it is excessively dirty, damaged, or torn.
3. Reinstall the filter with the white mesh first and black foam facing outward. Align the filter with the lid.

Maintaining the Brush Roll and Belts

1. Lay the vacuum down with the brush roll facing up. Remove five (5) screws with a Phillips-head screwdriver. Lift the brush cover to remove it.
2. Pull the brush roll out at both ends. Clean debris from the brush roll, motor pulley, and drive belt. Replace if needed.
3. Check the air passageway for obstructions. Twist the hose counterclockwise to remove and check for clogs.
4. Test the brush by holding it on end and spinning it. It should spin freely several times from one flick. If not, the brush will need to be replaced.
5. Grasp the drive belt, remove it from the motor shaft, and discard it. Loop a new drive belt over the motor shaft and stretch it over the brush roll in the space provided between the bristles.
6. Align the brush roll with the belt and turn it several times in the direction of the wheels to align. Reinstall the brush cover and the five (5) screws.

WARNING: To reduce the risk of electric shock, turn power switch OFF and disconnect the plug from the electrical outlet before performing maintenance or troubleshooting checks.

WARNING: Do not operate the vacuum with damp or wet filters, or without filters or the dirt tank in place. Allow components to dry before reassembling the dirt tank.

Maintaining the TurboBrush® Tool

For more helpful maintenance tips, visit support.BISSELL.com.

1. Twist the gray collar counter-clockwise until a slot appears, then separate the faceplate.
2. Remove the brush roll, belt, and paddle wheel. Inspect for damages and replace if necessary.
3. To reassemble, align the two clips on each end of the paddle wheel with the belt on, and pop it back into place. Place the brush roll with the belt back in. The faceplate will not close properly if all parts are not aligned correctly.

Cleaning the Hose and Foot

1. Locate the stretch hose where it connects to the hose elbow on the back of the machine. Clean any debris.
2. Locate the clear foot hose under the hose holder. Remove two screws and clear clogs and debris in the hose using a long, narrow object. Replace the screws and re-attach the stretch hose by sliding it over the inlet and rotating it upwards towards the lock position.

Note: If debris cannot be reached through the hose, follow the instructions for cleaning the air passageway in the "Maintaining the Brush Roll and Belts" section.

Troubleshooting

For a comprehensive walkthrough of your product and support tips, visit support.BISSELL.com.

(Specific troubleshooting steps are not detailed in the provided text, only a reference to the website.)

Warranty

Limited 2-year warranty, which may vary by state. Visit support.BISSELL.com or call 1-800-237-7691 for complete warranty information.

Every Purchase Saves Pets™

BISSELL proudly supports the BISSELL Pet Foundation® and its mission to help save homeless pets. When you buy a BISSELL® product, you help save pets, too. BISSELL is proud to design products that help make pet messes, odors, and pet homelessness disappear. Visit BISSELLsavespets.com to learn more.