Harbor Breeze LED Flood Light Projector

Introduction

Thank you for purchasing this Harbor Breeze product. These instructions are designed to help you enjoy the product with ease. For additional information, visit Lowes.com, search the item number, and refer to the Guides & Documents tab.

For customer service, call 1-888-251-1003 (8 a.m. - 8 p.m. EST, Monday - Sunday), email partsplus@lowes.com, or visit www.lowespartsplus.com.

Preparation

Before assembly, ensure all parts are present by comparing them with the package contents list. Do not assemble if any parts are missing or damaged.

Estimated Assembly Time: 10 minutes

Tools required: None

For more information, visit www.lowes.com.

Troubleshooting

Problem: The light does not turn on at night.

• Possible Cause 1: The transformer is not plugged in or turned on.
• Corrective Action 1: Ensure the transformer is plugged in and turned on.
• Possible Cause 2: Fixture connector is not properly installed on the low voltage cable.
• Corrective Action 2: Ensure the contact pins pierce the wire insulation and make proper contact with the wire.

Care and Maintenance

Clean the lens, lamp head, and lamp stand regularly with a non-abrasive cleaner. Warning: Always ensure the flood light is unplugged and completely cool before cleaning.

Warranty

This fixture is warranted against defects in materials and workmanship for five (5) years from the original purchase date. To obtain a Return Authorization number and further instructions, call 1-888-251-1003. The manufacturer is liable for replacement of defective items but not for other losses, damages, or injuries caused by the product.

Safety Information

Please read and understand this entire manual before assembling, operating, or installing the product.

Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

• This product is not a toy and must not be operated by children.
• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
• Do not submerge in water. The product can be damaged.
• Use with 18AWG minimum, underground low-voltage circuit cord.

Warning

• Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
• For use with low-voltage landscape lighting systems only.
• The wire is intended for shallow burial, less than 6 in. deep.
• Install all luminaires 10 ft. or more from a pool, spa or foundation.
• Keep lamp away from material that may burn.
• Do not touch hot lens, guard or hot fixture housing.
• Do not operate or install a fixture with missing or damaged parts.
• Do not touch the LED at any time as this may cause damage to the fixture.

Installation Overview

Step 1: Insert wire from low-voltage transformer (sold separately) into the wire guide by twisting the wire into each end of the wire guide. Align the pins on the connector top cover so that each pin lines up with opposite sides of the wire. Securely tighten the connector top cover making sure the pins completely pierce the plastic shield of the wire.

Step 2: Connect the wire from the low-voltage transformer (sold separately) to the wire guide by twisting the wire into each end of the wire guide. Align the pins on the connector top cover so that each pin lines up with opposite sides of the wire. Securely tighten the connector top cover making sure the pins completely pierce the plastic shield of the wire.

Step 3: Connect the wire from the low-voltage transformer (sold separately) to the wire guide by twisting the wire into each end of the wire guide. Align the pins on the connector top cover so that each pin lines up with opposite sides of the wire. Securely tighten the connector top cover making sure the pins completely pierce the plastic shield of the wire.

Operating Instructions

Step 1: [Diagram showing connection of wire to fixture]