Metra Online | Welcome to Metra Auto Parts Online Warehouse
Instruction Manual for MeTra models including: 99-5852CH, Ford explorer 11-15 Single Double Din Dash Kit
† With single zone, manual climate control Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications F G D. 2 386.257.1187 | MetraOnline.com DASH DISASSEMBLY 1. Unclip and remove the (2) trim panels from the left and right side of the factory
234567899891906 9 7 CONNECTIONS (CONT.) USB retention harness: • Unsnap the factory USB and 3.5mm jack panel from the pocket area. • Unplug both harnesses going to the USB and 3.5
2020-09-20 —
File Info : application/pdf, 12 Pages, 1.38MB
DocumentDocument99-5852CH INSTALLATION INSTRUCTIONS Ford Explorer () 2011-2015 With single zone, manual climate control Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications KIT FEATURES · ISO DIN radio provision with pocket · ISO DDIN radio provision · Included interface for climate and steering wheel functions · Retains factory USB and back-up camera (if equipped) · Painted charcoal with a matte black center KIT COMPONENTS · A) Radio trim panel · B) Radio brackets · C) Pocket · D) Heated seat buttons (L & R) Blank panels · E) (2) Panel clips · F) (2) #4 x 1/2" Phillips pan-head screws · G) (4) #8 x 3/8" Phillips truss-head screws · H) Wiring harness (not shown) · I) Antenna adapter (not shown) A B C D E F G TABLE OF CONTENTS Dash Disassembly..................................................2 Kit Preparation.......................................................3 Kit Assembly ISO DIN radio provision with pocket..................4 ISO DDIN radio provision.....................................4 Axxess Interface Installation.............................5-11 Final Assembly.......................................................9 WIRING & ANTENNA CONNECTIONS Wiring Harness: Axxess interface built into kit Antenna Adapter: Included with kit Steering wheel control interface: Included with kit TOOLS REQUIRED · Panel removal tool · Phillips screwdriver · 9/32" socket wrench · Torx screwdriver Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition. Metra. The World's Best Kits.® MetraOnline.com © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 6/22/21 INST99-5852CH 1. Unclip and remove the (2) trim panels from the left and right side of the factory radio. (Figure A) 2. Remove (4) 9/32" screws securing the radio/climate control panel to the dash. (Figure B) 3. Unclip, unplug, and remove the factory radio/climate control panel. (Figure C) (Figure A) DASH DISASSEMBLY 4. Remove (4) 9/32" screws securing the radio chassis, then unplug and remove. (Figure D) 5. Remove (4) 9/32" screws securing the factory display, then unplug and remove. (Figure E) Continue to Kit Preparation (Figure D) (Figure B) (Figure E) (Figure C) 2 386.257.1187 | MetraOnline.com 1. Remove (2) Torx screws securing the a/c vents to the factory radio/climate control panel, then unclip and remove them from the panel. (Figure A) 2. Attach the a/c vents to the radio trim panel using the (2) #4 x 1/2" Phillips screws provided with the kit. (Figure B) 3. Attach the panel clips provided with the kit onto the radio trim panel. The factory clips may also be used if desired. (Figure C) Continue to Kit Assembly (Figure A) KIT PREPARATION (Figure B) (Figure C) REV. 6/22/2021 INST99-5852CH 3 ISO DIN radio provision with pocket 1. Secure the radio brackets to the pocket using (4) #8 x 3/8" Phillips truss-head screws provided. (Figure A) 2. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 3. Slide the radio into the bracket/pocket assembly, then secure it using screws supplied with the radio. (Figure B) Continue to Axxess Interface Installation (Figure A) KIT ASSEMBLY ISO DDIN radio provision 1. Secure the radio brackets to the radio using screws supplied with the radio. (Figure A) Continue to Axxess Interface Installation (Figure A) (Figure B) 4 386.257.1187 | MetraOnline.com AXXESS INTERFACE INSTALLATION INTERFACE FEATURES · Provides retained accessory power (10-amp) · Provides illumination, parking brake, reverse, and speed sense outputs · Retains audio controls on the steering wheel · Retains factory USB and back-up camera (if equipped) · Can be used in both amplified and non-amplified models · Retains balance and fade · Micro-B USB updatable TABLE OF CONTENTS Connections ...........................................................................................................................................6-7 Installation ...............................................................................................................................................8 Programming ........................................................................................................................................... 8 Configuration menu ............................................................................................................................9-11 INTERFACE COMPONENTS · Axxess interface (built into kit) · Vehicle harness (LD-TSCREEN-FD3) · USB retention (LD-FDUSB) · Backup camera harness (LD-FDCAM-12) · Climate control harness (LD-EXPL-SZ) · 16-pin harness (LD-2NAVAMP) · 3.5mm adapter TOOLS REQUIRED · Crimping tool and connectors, or solder gun, solder, and heat shrink · Tape · Wire cutter · Zip ties REV. 6/22/2021 INST99-5852CH 5 CONNECTIONS From the 16-pin harness to the aftermarket radio, connect the: · Red wire to the accessory wire. · Blue/White wire to the amp turn on wire. · Orange/White to the illumination wire. · Gray wire to the front right positive speaker output. · Gray/Black wire to the front right negative speaker output. · White wire to the front left positive speaker output. · White/Black wire to the front left negative speaker output. The following (3) wires are only for multimedia/navigation radios that require these wires. · Blue/Pink wire to the VSS/speed sense wire. · Green/Purple wire to the reverse wire. · Light Green wire to the parking brake wire. · Tape off and disregard the following (5) wires: Brown, Green, Green/Black, Purple, Purple/Black If applicable From the 5852 vehicle harness to the aftermarket radio, connect the: · Black wire to the ground wire. · Yellow wire to the battery wire. · Green wire to the rear left positive speaker output. · Green/Black wire to the rear leftnegative speaker output. · Purple wire to the rear right positive speaker output. · Purple/Black wire to the rear right negative output. · Disregard the Red and White RCA jacks labeled "RSE/SYNC®/SAT". · Disregard the Red and White RCA jacks labeled "FROM 3.5". · Tape off and disregard the following (3) wires: Blue, Blue/White, Red. · Disregard the DIN jack. Continued on the next page 6 386.257.1187 | MetraOnline.com CONNECTIONS (CONT.) 3.5mm jack - steering wheel control retention: From the 3.5mm jack to the aftermarket radio: · Parrot: Connect the AX-SWC-PARROT (sold separately) to the 3.5mm jack, then to the radio. · For the radios listed below: Connect the 3.5mm adapter to the 3.5mm jack. · Eclipse: Brown - Brown/White / Brown/White - Brown · Kenwood / JVC (with SWC wire): Blue/Yellow - Brown · Metra OE: Key 1 (Gray) - Brown · Universal "2 or 3 wire" radio: Key-A or SWC-1 - Brown / Key-B or SWC-2 - Brown/White Note: After programming, assign SWC buttons within menu. · XITE: SWC-2 - Brown · For all other radios: Connect the 3.5mm jack to the radio. USB retention harness: · Unsnap the factory USB and 3.5mm jack panel from the pocket area. · Unplug both harnesses going to the USB and 3.5 · Plug in the LD-FDUSB to the factory USB panel · Snap in the factory USB panel and run the USB through to the aftermarket radio. Climate harness: Connect the small 6-pin to the kit's passenger airbag light and the other 6-pin to the vehicle harness. The larger 6-pin, the 2-pin, and the blue/red wire will not be used in this application. The 14 pin will be connected to the touch screen next in the installation section. REV. 6/22/2021 INST99-5852CH 7 INSTALLATION PROGRAMMING 1. Connect the 16-pin harness into port A. 2. Connect the 14-pin from the climate harness into port B, and then connect the small 6-pin to the kit's passenger airbag light and the other 6-pin to the vehicle harness. The larger 6-pin, the 2-pin, and the blue/red wire will not be used in this application. 3. Connect the 5852 vehicle harness into port C, and then to the wiring harnesses in the vehicle. 4. Port D is a Micro-B USB input for updating the interface. 1. Open the driver's door, and keep open during the programming process. 2. Cycle the ignition on and wait until the climate control lights turn blue. Note: If the lights don't turn blue, unplug port C from the tactile panel for a few seconds, then try again. 3. Test all functions of the installation for proper operation, before reassembling the dash. 16-Pin Harness A C D B 5852 Vehicle Harness Micro-B USB Port for Updating 14-Pin Climate Harness 8 386.257.1187 | MetraOnline.com FINAL ASSEMBLY CONFIGURATION MENU 1. Slide the radio into the dash, then secure using the factory screws. 2. Reassemble the dash in reverse order of disassembly using the 99-5852CH radio trim panel. The buttons on the steering wheel will be used to enter, navigate, and make changes to the Configuration Menu in the kit. The display on the climate knobs will be used to view the menu. 1. With the driver's door open, press and hold the OK button (right side), then cycle the key on. 2. Press the Seek Up and Seek Down buttons to toggle through the menu options available. Refer to the Menu Options table for a list of options, and description of each option. 3. Navigate to "d o", then press the OK button to exit the Configuration Menu. 4. If no activity after 10-seconds the Configuration Menu will close. Menu Options Left Knob Display A.G r.d b.L U O d o Right Knob Display Will display current state n E Description OEM Amplifier Gain Radio Detection Backlight Version Number of Kit Done / Quit Continued on the next page REV. 6/22/2021 INST99-5852CH 9 CONFIGURATION MENU (CONT.) Steering Wheel Controls Radio Detection · Press the OK button on the steering wheel to start the auto detection process. Left Knob Display r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d r.d Right Knob Display 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Radio Manufacturer Eclipse (Type 1) Kenwood Clarion (Type 1) Boss (type 1) / Dual / Sony JVC Pioneer / Jensen Alpine Boss (type 4) / Visteon Valor Clarion (Type 2) Boss (Type 2) Eclipse (Type 2) LG Parrot XITE Philips Kicker JBL Insane Audio Magnadyne Boss (type 3) Axxera Keynotes 1 2 1 1 (Boss) 3 1 (Boss) 1 1 4 10 1. If the steering wheel controls don't work properly it is possible to change the radio type. 2. Get to the radio type sub menu. Rotate the right climate knob until the correct radio type is displayed on the knob display. Press the MAX AC button to set the new radio type. 3. If the display shows Alpine, but an Alpine radio isn't installed, make sure the 3.5mm jack is plugged in. 4. AX-SWC-PARROT required (sold separately). The software in the radio must be rev. 2.1.4 or higher. Backlight Left Knob Display b.L b.L b.L b.L b.L b.L b.L b.L b.L b.L Right Knob Display -rD Or YE LG Gr CY BL Pu HP Backlight Color No backlight Red Orange Yellow Lime Green Green Cyan Blue Purple Hot Pink 386.257.1187 | MetraOnline.com CONFIGURATION MENU (CONT.) OEM Amplifier Gain Left Knob Display A.G Version Number of Kit Left Knob Display U O Right Knob Display 0 to 30 Right Knob Display Will display current version of kit Done / Quit · Press the button on the steering wheel to exit the Configuration Menu. Left Knob Display d o Right Knob Display n E REV. 6/22/2021 INST99-5852CH 11 Metra. The World's Best Kits.® MetraOnline.com 99-5852CH INSTALLATION INSTRUCTIONS Having difficulties? We're here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 6/22/21 INST99-5852CH