ElectroluxInstruction Manual for Electrolux models including: EMBS2411AB, 24 Inch Built-In Side Swing Microwave Oven, EMBS2411AB 24 Inch Built-In Side Swing Microwave Oven, Built-In Side Swing Microwave Oven, Side Swing Microwave Oven, Swing Microwave Oven, Microwave Oven, Oven
EMBS2411AB Electrolux
Electrolux EMBS2411AB Built In Microwave | Town Appliance
File Info : application/pdf, 6 Pages, 4.33MB
DocumentDocumentInstallation Instructions Built-in Trim Kit Model # EMTK3011AS BEFORE YOU BEGIN Read these instructions completely and carefully. · IMPORTANT Save these instructions for local inspector's use. · IMPORTANT Observe all governing codes and ordinaces. · Note to Installer Be sure to leave these instructions with the Consumer. · Note to Consumer Keep these instructions for future reference. · Skill level - Installation of this appliance requires basic mechanical and electrical skills. · Proper installation is the responsibility of the installer. · Product failure due to improper installation is not covered under the Warranty. · Unplug the microwave oven before attempting installation of this kit. · Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury. · Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. FOR YOUR SAFETY: WARNING Before beginning the installation, switch power off at service panel and lock out to prevent being switched on accidentally. When the service cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. IMPORTANT - PLEASE READ AND FOLLOW THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY WITH ELECTROLUX MICROWAVE OVENS SPECIFYING BUILT-IN KIT QUESTIONS? For customers in the United States call:1-800-374-4432 For customers in Canada call: 1-800-265-8352 Visit our Website at: www.electroluxappliances.com READ CAREFULLY. KEEP THESE INSTRUCTIONS. EN-1 PN: A06822909 Nov. 2020 Installation Instructions PARTS INCLUDED IN THE KIT 1. Front Frame Assembly- QTY 1 2. Exhaust Duct - QTY 1 3. Rail QTY 2 4. Screw A - Short Screws - QTY 11 + 3 extra 5. Screw B - Long Screws - QTY 4 + 2 extra 6. Rear Duct CHOOSING A LOCATION FOR YOUR MICROWAVE OVEN IF BUILT-IN Built-In Trim Kit allows for the installation of microwaves listed below to be built into a cabinet or wall by itself or over an electric wall oven*. Microwave Model: EMBS2411AB Screw A - Short Screws Front Frame Assembly Screw B - Long Screws Rail See Illustration 1 for proper location and when building in above a wall oven. Carefully follow both the wall oven installation instructions and Electrolux's Built-in Kit instructions. If building over a wall oven, be sure the clearance between the wall oven and the microwave oven is a minimum of 3 inches.See illustration 2. Exhaust Duct Illustration 1 Rear Duct *NOTE: Trim Kit and microwave can only be built-in over an electric self-clean or non self-clean single cavity wall oven. CABINET OR WALL CUTOUT Cutout Dimensions(See illustration 3) Height (A) Minimum Maximum Width (B) Minimum Maximum 17-1/64"(432 mm) 17-1=/4" (438 mm) 24- 49/64 " (629 mm) 25" (635mm) Depth (C) Minimum 23-1/2" (597mm) Min.depth with receptacle outside cutout 22" (559mm) Min.depth with receptacle inside cutout 23-1/2"(597mm) Illustration 2 Trim Kit Overall Dimensions 30" Height 18-7/64'' (460mm) Width 29-55/64'' (758mm) Depth 1-5/8'' (41.6mm) 3"Min EN-2 Installation Instructions Screw A- Short Screws Center Line Illustration 3 ELECTRICAL OUTLET LOCATION Outlet should NOT be in the shaded area as indicated on Illustration 3 NOTE 1: The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven. Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling and rear partition. The proper functioning of the oven does not require the enclosure. Illustration 4 EXHAUST DUCT ASSEMBLY 1. Draw a Central Line on floor. Place the Exhaust Duct in the openingWhen the Exhaust Duct Assembly is in the opening correctly, the Center Line is in the middle of the Exhaust Duct Assembly. See Illustration 4. 2. Secure the Exhaust Duct Assembly with the three screw A - short screws. IMPORTANT: Secure screws in outer hole. 3 pcs are needed for exhaust duct assembly EN-3 Installation Instructions 1 LOCATE AND INSTALL THE EXHAUST DUCT Set Exhaust Duct into the front cabinet microwave oven cutout and center it right and left. Push back until the front flange is against the cabinet front wall. Mount the Exhaust Duct using 3 screw A - short screws. 3 INSTALL THE REAR DUCT 1. Gently return microwave oven to its upright position. 2. Remove screw A-short screw. Screw A- Short Screws Screw A -short screw 3. Align the rear duct with the back of microwave oven, as shown. Exhaust Duct Mounting Holes 2 INSTALL THE RAILS Disconnect the microwave oven from the receptacle. Remove everything out of the microwave oven, including packing, Owner's Manuals, turntable and turntable support. A protective film has been applied to some microwave oven and trim kits. If applied, remove the film. Turn over the microwave oven and secure the rails to oven Base Plate by inserting 4 screw A-short screws. See Illustration 5. Be careful not to scratch the microwave oven. Microwave Oven Bottom Rail Screw AShort Screws 4. Slide 2 tabs into the slots on the right side of the back of microwave oven. A B A. Rear duct tabs B. Slots 5. Use 2 screw A -short screws to secure top of rear duct to the back of microwave oven, as shown. A B C Flanges Illustration 5 Door A. Screw A -short screws (2) B. Rear duct C. Back of microwave oven EN-4 Installation Instructions 3 INSTALL THE REAR DUCT (continued) 6. Use 3 srew A -short screws to secure back of rear duct to the back of microwave oven, as shown. 5 SECURE THE RAILS TO THE CABINET Ensure the Exhaust Duct and Bottom Bracket front flanges are tight against the cabinet, and that the screws holes are aligned. Drive 4 screw A - short screws through the Exhaust Duct and Rails into the cabinet Mounting Holes AB C A. Screw A -short screws (3) B. Rear duct C. Back of microwave oven Screw A -short screw 4 INSTALL THE MICROWAVE OVEN Plug the power cord into the wall receptacle. Slide the microwave oven assembly gently into the cabinet, using care not to pinch the power cord. Be sure to keep the assembly centered as it slides back to where the tongue of the rails goes through the slots on Exhaust Duct. The top edges of the Exhaust Duct should now be centered right to left in the opening. The Exhaust Duct should be tight against the cabinet. Rail Guides 6 REPLACE ANY LOOSE ITEMS 1. Your microwave is now fully installed. Replace the turntable and turntable support that was removed from inside the microwave oven. 2. Keep these installation instructions and extra screws for future reference and need. Do not place them in the microwave oven. 3. Replace the house fuse, or close the circuit breaker to restore power at the service panel. Rails EN-5 Installation Instructions FRONT FRAME INSTALLATION 1. Position the FRONT FRAME ASSEMBLY to be square with the oven. Carefully place the FRONT FRAME ASSEMBLY on the oven. See Illustration 6. 2. Check that it is level and then secure with two Screws B - long screws Secure the bottom portion of the FRONT FRAME ASSEMBLY with the two remaining Screws B - long screws. See Illustration 7. Illustration 6 Illustration 7 EN-6
