Walkie-talkie User Manual

Product Description

This walkie-talkie features an antenna, LED flashlight, display, and a Type-C charging port. It also includes a microphone, speaker, and various buttons for operation.

Key Components:

• Antenna: For transmitting and receiving signals.
• LED Flashlight: Provides illumination.
• Display: Shows channel, settings, and battery status.
• Type-C charging port: For charging the device.
• PTT (Push to Talk): Press to transmit, release to listen.
• Microphone: For speaking into the device.
• Speaker: For listening to incoming transmissions.
• Volume & Menu Up/Down Buttons: Adjust volume or navigate menus.
• LAMP Button: Controls the flashlight and scanning functions.
• MENU Button: Accesses settings and menus.
• Lanyard hole: For attaching a lanyard.
• Channel/Menu Indicator: Shows current channel or menu selection.
• Scan Indicator: Indicates when scanning is active.
• VOX Indicator: Shows when Voice Operated Exchange is active.
• Battery Indicator: Displays battery level.
• Key lock Indicator: Shows when the keyboard is locked.
• CTCSS/DCS: Sub-code settings for privacy.
• Tx/Rx icon: Indicates transmission or reception.
• Volume: Displays current volume level.

Button Functions:

• PTT (Push to Talk): Press to talk, release to listen.
• Call tone/ Lock: Short press to call, long press to lock or unlock the keyboard.
• Flashlight/Scan: Short press to turn the flashlight on/off, long press to scan channels.
• Power key: Short press to enter menu settings, long press to power on/off.
• Up Arrow (▲): In non-menu state, short press to increase volume. In menu state, short press to adjust settings.
• Down Arrow (▼): In non-menu state, short press to decrease volume. In menu state, short press to adjust settings.

Before Use

• Please charge the device before first use using a 5V 1A charger.
• When the battery icon flashes, the battery is low. The icon stops flashing when fully charged.

How to Use

1. Power on or off: Long press the MENU button.
2. Set the Channel:
   • Short press the MENU button once. The channel number will flash.
   • Use the Up/Down arrow buttons to select the desired channel.
   • Press the PTT button to confirm.
3. Set the Sub-code:
   • Short press the MENU button twice. The sub-code will flash.
   • Use the Up/Down arrow buttons to select the sub-code (01-99). OF means no code. 01-38 are CTCSS codes, and 39-99 are DCS codes.
   • Press the PTT button to confirm.
4. Communication: Ensure all walkie-talkies in the group are set to the same channel and sub-code.
5. Speaking: Hold the walkie-talkie 2-3 inches (5-7 cm) from your mouth. Speak directly into the microphone. Do not cover the microphone while speaking. Release the PTT button when finished.
6. Note: To communicate with other FRS radio stations that do not have interference cancellation codes, set the sub-code to OF.
7. VOX (Voice-Operated Exchange): Allows talking without pressing the PTT button.
   • Short press the MENU button three times to enter VOX settings. The default is OF (off).
   • Use the Up/Down arrow buttons to set the sensitivity level (1, 2, or 3, with 3 being the most sensitive).
   • Press the PTT button to confirm.
8. Adjust the volume: Use the Up/Down arrow buttons to adjust the volume from level 1 to 8.
9. Channel scanning: Long press the LAMP button to scan channels. Short press the PTT button to stop scanning.
10. Call: Short press the PTT button to call the group.
11. Set the call tone:
    • Short press the MENU button four times. The screen will display "CA 01", and "01" will flash.
    • Use the Up/Down arrow buttons to select one of the 10 calling tones.
    • Press the PTT button to confirm.
12. End call tone:
    • Short press the MENU button six times. The screen will display "CO on".
    • Use the Up/Down arrow buttons to turn the end call tone on or off. "ON" means a tone will sound when PTT is released. "OF" means no tone will sound.
13. Turn button sounds on and off:
    • Short press the MENU button five times. The screen will display "LO on", and "on" will flash.
    • Use the Up/Down arrow buttons to turn the button sounds on or off.
14. Lock the keyboard: Long press the PTT button to lock or unlock the keyboard. When locked, only PTT/Call tone/Flashlight functions are available.
15. Flashlight: Short press the LAMP button to turn the flashlight on or off.

The device is CE, FC, and RoHS certified and Made in China.