Buzbug MA-22 Bug Zapper with Sticky Glue Board

Introduction

At Buzbug, we are devoted to a greener future as pioneers in energy conservation for the pest control industry. We are front-lining the technology by replacing UV bulbs with state-of-the-art UV-LEDs. We are also proud to introduce solar solutions for some of our outdoor pest control products.

24/7 Support: Buzbug Guarantees 100% Satisfaction To Every Customer. Visit buzbug.com to chat with a live representative, or email support@buzbug.com for assistance and inquiries. This product is covered in a 12-month warranty program.

Before Using

0.1 How long does it take for this product to be fully charged?
Charging fully with the provided cable takes about 5 hours. Low battery will affect the product effect. When the battery is low, please use the provided cable to charge in time.

0.2 How long can the product last on a full charge?
A full charge provides: 20 hours with the UV-LED light, 16 hours with the warm light.

0.3 Is it normal that the warm light beads do not light up in UV-LED mode?
Yes. The warm light beads will light up only in the warm light mode.

0.4 Is it necessary to clean my bug zapper regularly?
The buildup of dead insects can reduce the product's effectiveness. It's recommended to replace the sticky glue board and clear the collection tray regularly.

0.5 How do I properly replace a sticky glue board or a lamp?

Step 1: Power Off
Before replacing, make sure the device is turned off and unplugged.

Step 2: Sticky Glue Board Replacement
1. Unscrew to remove the collection tray at the bottom.
2. Slip the new sticky glue board over the outside of the adhesive board grid and peel off protective paper from the glued surface. Avoid touching the glued area as it is sticky.
3. Install the entire base back into the bug zapper.

Step 2: Lamp Replacement
1. Unscrew to remove the collection tray at the bottom.
2. Take out the lamp. Insert the new lamp into the socket. (Note: The tab on the lamp needs to be aligned with the tab on the socket. As shown in the figure)
3. Install the entire base back into the bug zapper.

Product Diagram

Model: MA-22

Dimensions: 5.74" x 5.74" x 11.61" (146 × 146 × 295 mm)

Net Weight: 670g

Features:

• Handle
• Charging Indicator Light
• Protective Safety Grid
• Adhesive Board Grid
• Switch Button
• Type-C Charging Port
• UV-LED Lamp
• Collection Tray
• Sticky Glue Board

Specifications:

• UV-LED Light Power: 1W
• Warm Light Power: 1.5W
• Input: Type-C DC 5V/2A
• Battery Capacity: 4500mAh
• Battery Type: Lithium-ion Battery
• EPA EST Number: 104617-CHN-1
• Charging Time: 5 hours

Directions for Use

1. Charge: The indicator light turns red when charging and turns blue when fully charged. Use a DC 5V/2A charger for a full charge in 5 hours. Note: Charging fully before first use is recommended.

2. Operation:
- Long press the switch button for 3 seconds to turn on and activate UV-LED light.
- Short press to cycle between UV-LED light and warm light.
- Long press the switch button for 3 seconds to turn off the device.

Warm Tip: Some bugs, particularly flies, are more attracted to smells than to lights. For optimal results, consider placing bait at the bottom of the tray, such as fruit peels, ham, or dessert, to draw them in effectively.

3. Battery Life: The product's battery capacity is 4500mAh. When fully charged: Operating the UV-LED light lasts about 20 hours; Operating the warm light lasts about 16 hours.

4. Cleaning and Replacing: Before cleaning and replacing, always turn off and unplug the appliance. It's recommended to replace the sticky glue board regularly for better product performance.

Important Warnings

• This product must not be used near curtains or other combustible materials.
• The product is not waterproof. Please refrain from using it outdoors during rainy conditions, and avoid rinsing the product with water to ensure its proper functionality and safety.
• For a better bug-zapping effect, please place the bug zapper from other light sources.
• Always keep the product out of the reach of children.
• Always keep the product out of reach of pets to prevent pet hair from getting stuck on the sticky glue board.

FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Correct Disposal of this Product (Waste Electrical & Electronic Equipment)

This marking shown on the product or its literature, indicates that it should not be disposed of with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Manufacturer Information

Manufacturer: Shenzhen Rock Creation Technology Co., Ltd.

Address: 4/F, No. 2, Aoxiang Road, Zhangbei Community, Longcheng Street, Longgang District, Shenzhen City, Guangdong Province, China

EC REP: UAB Qixiang Europe, Pranciškonų g. 6-46, LT-01133 Vilnius, Lithuania. Email: qixiang.europe@gmail.com, Phone: +49 6976 895074

UK REP: CET Product Service Ltd., Beacon House Stokenchurch Business Park, Ibstone Rd, Stokenchurch, High Wycombe HP14 3FE UK. Email: info.cetservice@gmail.com, Phone: +44 741 932 5266

Made in China