Hios Cl 6500 Manual Pdf - Electric Screwdrivers and Power Supply Operation Manuals
HIOS Power Supply CLT-50 ID 001657 (10/22): World Equipment Source Item: HIOS Power Supply Model: CLT-50 Notes:
Power Pack for Electric Screwdrivers Operation Manual (March 2017) 17A No. ET-A018 Please read carefully the operating instructions for the electric screwdriver and take care to use it properly. Warning Read and understand the following cautions to use the Hios electric screwdriver, exclusive power supply, etc. safely and properly. Failure to follow all the cautions listed below may result in electric shock, fire and/ or serious personal injury. 1. Use the equipment with the indicated proper voltage and always connect the equipment to ground while in use. 2. For safety, only use the equipment with a commercial power supply equipped with a short-circuit breaker or safety breaker. 3. If a short-circuit breaker or other circuit breaker trips, stop operation immediately, disconnect the power cord, and consult a Hios representative for repair. 4. Do not use the equipment with wet hands. This could cause an electric shock. 5. Do not put the equipment near high-voltage/high-amperage machinery. 6. Do not use the equipment in or near a combustible gas, liquid or powder. 7. Do not use the equipment where static electricity (sparking) may occur. 8. Do not use the equipment with anything except a Hios electric screwdriver. Hios can accept no responsibility for problems that occur if a power supply not made by Hios is used with a Hios electric screwdriver. 9. Do not disassemble or modify the equipment. 10. When the equipment is not being used, turn off the power switch and disconnect the power cord from the outlet. 11. If the equipment overheats or a circuit breaker trips, stop operation immediately and consult a Hios representative for repair. 12. Do not abuse the cord. Never drag the power supply by its screwdriver cord or power cord. When disconnecting the power cord, hold and pull the plug. 13. Do not bring oil-based products or sharp edges near the cords. 14. Only use the equipment in locations with suitable humidity and temperature, which have no smoke, dust, corrosive gases, etc. 15. Only use the equipment on a stable flat surface. Do not stack the equipment with other objects. 16. Do not put anything on the power supply. This could cause heating. 17. Do not drop or apply strong impacts to the equipment. This could damage the structure and contents of the equipment. Always check that the equipment has no damage before use. 18. Keep out of reach of children during use and during storage. 19. Store the equipment in a stable position in a location with suitable temperature and humidity. Hios screwdrivers run from power packs Power pack model CLT-50AF CLT-100 CLT-75 CLT-75AF Number For one drivers For two drivers Hios electric screwdrivers for use with Hios power packs CL·SS· driver CL-9000 CL-2000, CL-3000, CL-4000, CL-6000, CL-6500 SS-2000, SS-3000, SS-4000, SS-6500 -4500, -5000 CL-2000, CL-3000, CL-4000, CL-6000, CL-6500 SS-2000, SS-3000, SS-4000, SS-6500 -4500, -5000 For CL-9000 For CL-9000 Specification Power Pack Model Primary Input side voltage Output voltage Size (mm) (W) × (D) × (H) Weight AC Cord Length CLT-50AF CLT-100 CLT-75 CLT-75AF AC100V/120V/220-240V ± 5% (50/60 Hz) AC100V± 5% (50/60 Hz) HI, LOW HI, LOW HI only 105 × 185 × 91 182 × 145 × 132 182 × 220 × 133 2.7 kg 4 kg 6 kg 1.8 m (inlet cord with ground wire) * Except for 100V of CLT-50AF, it is a Special order item. Replacing a Fuse The LED will not light when the fuse burns out. If the LED doesn't go on after the fuse is replaced, the power cord may be damaged. In this case, discontinue use immediately and notify a Hios service agent. spare fuse China RoHS2 Table If you export to China by yourselves, below is the table of China RoHS2. * In addition, if the following mark cannot be found at the rear side of the product and/or Product box, cut off a mark and stick a mark to the product and/or product box. Note: minimum size of China RoHS mark is 5mm at outer diameter HIOS Inc. 1-16-5 Akiyama, Matsudo City, Chiba Pref., Japan TEL: 81-47-392-2001 FAX: 81-47-392-7773 Time Chart Driver start signal Driver running Torque up signal Finish signal* *Finish signal is not output during reverse-rotaion. When the screwdriver "Torque up" then the screwdriver stop turning. "Finish signal" is active after "Torque up" of screwdriver until "Lever Off" of screwdriver. No "Finish signal" for Reversing. Finish output (Relay contact) Terminal On/OFF Time: 20 ms or less / 20 ms or less Contact resistance 100m or less Max.current 2A 125V AC 1A 250V AC (1A 30V DC)Adobe PDF Library 9.9 Adobe InDesign CS5.5 J (7.5)