AC Infinity Cloudlab Series Heavy-Duty Grow Tent

Manual Code

CL2010X1

Product Information

Manual Index

• Key Features

• Product Contents

• Tent Set Up

• Mounting Guide

• Ventilation Guide

• Other AC Infinity Products

• Warranty

Key Features

• High-Density Canvas

  Mylar canvas with 2000D density rating to be 100% external light-proof. Diamond-patterned interior lining amplifies reflectivity.

• Viewing Window

  Clear and adjustable window offers a snapshot of the interior without compromising your environment.

• Controller Plate

  Aluminum plate designed to mount fan and lighting controllers. Their cords can enter the tent securely through the plate's opening.

• Heavy-Duty Frame

  Thick 22mm steel tubes and connectors provide the tent with a sturdy structure. Can carry fans and lights up to 100 pounds.

• Spill Tray

  Reflective waterproof lining that catches water, soil, and other debris to prevent leakage in the grow tent.

• Storage Bag

  Includes a heavy-duty nylon carrying bag to neatly store the grow tent when not in use and allow easy transporting.

Product Contents

CLOUDLAB SERIES (Included in all series)

• Canvas Tent (x1)
• Storage Bag (x1)
• Spill Tray (x1)
• Filter Straps (x2)
• Controller Screws (x10)
• Controller Velcro (x6)
• Inner Flap Velcro (x2)

CLOUDLAB SERIES (Included only with specific models)

• CLOUDLAB 844 (AC-CBA844), CLOUDLAB 866 (AC-CBA866): Controller Plate (x1), Frame Poles (A x8, B x4, C x4, D x8, E x1, F x1)
• CLOUDLAB 422 (AC-CBA422), CLOUDLAB 733 (AC-CBA733): Controller Plate (*SHORT) (x1), Frame Poles (A x8, B x4, C x4, D x8, E x1, F x1)
• CLOUDLAB 632 (AC-CBA632): Controller Plate (*SHORT) (x1), Frame Poles (A x4, A1 x4, B x4, C x4, D x8, E x1, F x1)
• CLOUDLAB 642 (AC-CBA642): Controller Plate (x1), Frame Poles (A x4, A1 x4, B x4, C x4, D x8, E x1, F x2)

Tent Setup

Step 1

Insert the eight (A) poles into the floor end of the corner (D) pieces to create two bases. Ensure the feet of each corner (D) piece face the floor with the arrow pointing down. Note: Poles in models AC-CBA632 and AC-CBA642 are labeled A1 and A2.

Diagram: Shows insertion of poles (A) into corner pieces (D) to form bases. Arrows indicate correct orientation.

Step 2

Insert the four (B) poles into Base One. Insert the four (C) poles into Base Two.

Diagram: Illustrates inserting poles (B) into Base One and poles (C) into Base Two.

Step 3

Unzip the tent so that three of the walls lay flat.

Diagram: Shows the tent unzipped with walls laid flat, indicating 'Door', 'Bottom', and 'Roof' sections.

Step 4

Guide Base One into the floor of the tent, making sure its corners meet the tent's corners.

Diagram: Shows Base One being placed into the bottom of the tent.

Step 5

Insert the poles of Base Two into the poles of Base One to complete the frame. Two people are recommended for this portion of the tent assembly.

Diagram: Illustrates connecting Base Two poles to Base One poles to form the tent frame.

Step 6

Pull the roof over the assembled frame. Two people are recommended for this portion of the tent assembly.

Diagram: Shows the tent fabric being pulled over the assembled frame.

Step 7

Pull the upper and lower zippers to close the walls and door. Two people are recommended for this portion of the tent assembly.

Diagram: Shows zippers being pulled to close the tent walls and door.

Step 8

You can neatly hold the window wall open any time by using its attached Velcro strap.

Diagram: Shows the Velcro strap used to hold the window open.

Step 9

Add the roof support beams (E) then (F). Insert the spill pool into the tent and secure the Velcro straps around the poles.

Diagram: Illustrates adding roof support beams (E, F) and inserting the spill tray.

Step 10

Mount your controller onto the included bracket. Use the included screws to mount an AC Infinity controller. Use the Velcro adhesive to attach a non-AC Infinity controller. Refer to page 15 for mounting locations of your controller.

Diagram: Shows a controller being mounted onto the bracket using screws or adhesive.

Step 11

Slide the controller bracket assembly into the tent straps below the logo.

Diagram: Shows the controller bracket being slid into the tent straps.

Step 12

Route your inline duct fan's power connector through the opening inside and plug it into your controller. Plug the probe into the controller and route its cables through the opening.

Diagram: Illustrates routing fan power connector and probe cables through the tent opening to the controller.

Mounting Guide

Controller Plate

This grow tent includes an aluminum bracket with mounting holes bored for AC Infinity controllers. Mount your controller to the corresponding holes on the bracket. Route its wires through the oval opening and through the grow tent's flap. To attach non-AC Infinity controllers, use the included Velcro adhesive to hold it onto the bracket.

ONLY INCLUDED WITH CLOUDLAB 642, CLOUDLAB 844, CLOUDLAB 866

Diagram: Shows controller plates with various mounting hole configurations for these models.

ONLY INCLUDED WITH CLOUDLAB 422, CLOUDLAB 632, CLOUDLAB 733

Diagram: Shows controller plates with various mounting hole configurations for these models.

*Controllers Sold Separately

Ventilation Guide

Inline Fan and Grow Light

First hang your inline duct fan by the roof support beams. Position the fan on the opposite end of your intake hole to optimize airflow. If you are installing a carbon filter inside, use the included straps to hang the carbon filter. Then install your grow light. You may use rope clip hangers to install these products.

Double-Sided Cinches

Install any necessary duct tubes onto the ducting ports. Use the cinches on either end to secure the duct tubes onto the grow tent.

Intake Holes

Introduce fresh air by using one of the two ventilation holes at the bottom of the grow tent. Open a passive intake screen or create active intake by attaching an additional inline fan to a duct port.

Diagram: Shows airflow entering the tent through the bottom intake holes and exiting through the top.

Need More Information?

Scan the QR code or visit www.acinfinity.com for more guides and tutorials.

AC Infinity Products

Inline Fans

The CLOUDLINE series is a line of duct fans designed to quietly ventilate AV rooms and closets, as well as various DIY air circulation and exhaust projects. Features a thermal controller with intelligent programming that will automatically adjust duct fan speeds in response to changing temperatures.

Diagram: Shows an AC Infinity inline fan.

Carbon Filter

The duct carbon filter is designed to eliminate odors and chemicals for grow tents and hydroponic spaces. It utilizes premium grade Australian charcoal that features greater absorption power and a longer lifespan. Enables maximum airflow pass through as part of an intake or an exhaust system.

Diagram: Shows an AC Infinity carbon filter.

Ducting Tubes

The four-layer ducting tube is used to direct airflow, designed for ventilation systems in applications like HVAC, dryers, and grow rooms. It is highly durable and flexible, and can be used anywhere from tight spaces to wide open areas.

Diagram: Shows an AC Infinity ducting tube.

Discover the latest innovations in cooling and ventilation at acinfinity.com

Warranty

This warranty program is AC Infinity's commitment to you. Products sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, AC Infinity will take appropriate actions defined in this warranty to resolve any issues.

The warranty program applies to any order, purchase, receipt, or use of any products sold by AC Infinity or its authorized dealerships. The program covers products that have become defective, malfunctioned, or unusable. The warranty program goes into effect on the date of purchase and expires two years from the date of purchase. If your product becomes defective during that period, AC Infinity will replace it with a new one or issue a full refund.

The warranty program does not cover abuse or misuse, including physical damage, submersion in water, incorrect installation (such as wrong voltage input), and misuse for any reason other than intended purposes. AC Infinity is not responsible for consequential loss or incidental damages of any nature caused by the product. Damage from normal wear, such as scratches and dings, is not covered.

For more information about AC Infinity's dealers and distributors, please contact customer service at support@acinfinity.com or (626) 923-6399, Monday to Friday, 9:00 am to 5:00 pm PST.

Image: A circular badge with "100% GUARANTEE" text.

If you run into any issues with this product, contact AC Infinity and they will happily issue a replacement or a full refund!