If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner's Manual, Navigation/. Uconnect Manuals ...
Manual climate controls. Air Recirculation. ... For complete owner information, refer to your Owner's Manual on the DVD in the owner’s kit provided at the time of new...
User Guide 2014 Wrangler Includes Wrangler Unlimited Information Provided by: If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner's Manual, Navigation/ Uconnect® Manuals or Warranty Booklet by calling 1-877-426-5337 (U.S.) or 1-800-387-1143 (Canada) or by contacting your dealer. The driver's primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in a collision and personal injury. Chrysler Group LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road. Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous and could lead to a serious collision. Texting while driving is also dangerous and should never be done while the vehicle is moving. If you find yourself unable to devote your full attention to vehicle operation, pull off the road to a safe location and stop your vehicle. Some States or Provinces prohibit the use of cellular telephones or texting while driving. It is always the driver's responsibility to comply with all local laws. Important: This User Guide is intended to familiarize you with the important features of your vehicle. The DVD enclosed contains your Owner's Manual, Navigation/Uconnect® Manuals, Warranty Booklets, Tire Warranty and Roadside Assistance (new vehicles purchased in the U.S.) or Roadside Assistance (new vehicles purchased in Canada) in electronic format. We hope you find it useful. Replacement DVD kits may be purchased by visiting www.techauthority.com. Jeep® is a registered trademark of Chrysler Group LLC. Copyright 2013 Chrysler Group LLC. Information Provided by: TABLE OF CONTENTS INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC . . . . . . . . . . . . . . . . . 89 CONTROLS AT A GLANCE DRIVER COCKPIT . . . . . . . . . . . . . . . 6 INSTRUMENT CLUSTER . . . . . . . . . . 8 GETTING STARTED KEY FOB . . . . . . . . . . . . . . . . . . . 10 REMOTE START . . . . . . . . . . . . . . 11 THEFT ALARM . . . . . . . . . . . . . . . 11 SEAT BELT . . . . . . . . . . . . . . . . . . 12 SUPPLEMENTAL RESTRAINT SYSTEM (SRS) -- AIR BAGS . . . . . . . . . . . . 13 CHILD RESTRAINTS . . . . . . . . . . . . 14 FRONT SEATS . . . . . . . . . . . . . . . . 19 REAR SEATS . . . . . . . . . . . . . . . . . 20 TILT STEERING COLUMN . . . . . . . . . 21 HEATED SEATS . . . . . . . . . . . . . . . 22 OPERATING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS . . . . . . . . . . . 23 TURN SIGNAL/LIGHTS LEVER . . . . . . 23 WIPER/WASHER LEVER . . . . . . . . . . 25 SPEED CONTROL . . . . . . . . . . . . . . 26 MANUAL CLIMATE CONTROLS . . . . . . 27 AUTOMATIC TEMPERATURE CONTROLS (ATC) . . . . . . . . . . . . . . 28 SUNRIDER® AND SOFT TOP . . . . . . . 29 HARD TOP AND FREEDOM TOP® . . . . 38 DUAL TOP -- IF EQUIPPED . . . . . . . . 41 WIND BUFFETING . . . . . . . . . . . . . 41 ELECTRONICS YOUR VEHICLE'S SOUND SYSTEM . . . 42 Uconnect® 130 . . . . . . . . . . . . . . . 44 Uconnect® 130 WITH SiriusXM SATELLITE RADIO . . . . . . . . . . . . . . 46 Uconnect® 230 . . . . . . . . . . . . . . . 49 Uconnect® 430/430N . . . . . . . . . . . 52 Uconnect® 730N . . . . . . . . . . . . . . 62 SiriusXM SATELLITE RADIO/TRAVEL LINK . . . . . . . . . . . . . . . . . . . . . . 73 STEERING WHEEL AUDIO CONTROLS . . . . . . . . . . . . . . . . . 77 iPod®/USB/MP3 CONTROL . . . . . . . . 77 Uconnect® Phone . . . . . . . . . . . . . . 78 Uconnect® VOICE COMMAND . . . . . . . 81 Bluetooth® STREAMING AUDIO . . . . . 84 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . 84 PROGRAMMABLE FEATURES . . . . . . . 86 POWER INVERTER . . . . . . . . . . . . . 87 POWER OUTLETS . . . . . . . . . . . . . 88 OFF-ROAD CAPABILITIES (4WD OPERATION) COMMAND-TRAC®/ROCK-TRAC® . . . . . 89 AXLE LOCK (TRU-LOK®) RUBICON ONLY . . . . . . . . . . . . . . . . . . . . . . 89 ELECTRONIC SWAY BAR DISCONNECT RUBICON ONLY . . . . . . . . . . . . . . . 90 UTILITY TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) . . . . . . . 91 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) . . . . . . . . . . . . 93 WHAT TO DO IN EMERGENCIES ROADSIDE ASSISTANCE . . . . . . . . . . 96 INSTRUMENT CLUSTER WARNING LIGHTS . . . . . . . . . . . . . . . . . . . . 96 IF YOUR ENGINE OVERHEATS . . . . . 101 JACKING AND TIRE CHANGING . . . . 102 JUMP-STARTING . . . . . . . . . . . . . 107 EMERGENCY TOW HOOKS . . . . . . . 109 SHIFT LEVER OVERRIDE . . . . . . . . 109 TOWING A DISABLED VEHICLE . . . . 110 FREEING A STUCK VEHICLE . . . . . . 110 EVENT DATA RECORDER (EDR) . . . . 111 MAINTAINING YOUR VEHICLE OPENING THE HOOD . . . . . . . . . . 112 ENGINE COMPARTMENT . . . . . . . . 113 FLUIDS AND CAPACITIES . . . . . . . . 114 MAINTENANCE SCHEDULE . . . . . . 115 MAINTENANCE RECORD . . . . . . . . 119 FUSES . . . . . . . . . . . . . . . . . . . . 120 TIRE PRESSURES . . . . . . . . . . . . 123 WHEEL AND WHEEL TRIM CARE . . . 125 EXTERIOR BULBS . . . . . . . . . . . . 125 Information Provided by: TABLE OF CONTENTS CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER . . . . . . . . . . . 126 CHRYSLER CANADA INC. CUSTOMER CENTER . . . . . . . . . . . 126 ASSISTANCE FOR THE HEARING IMPAIRED . . . . . . . . . . . . . . . . . 126 PUBLICATIONS ORDERING . . . . . . . 126 REPORTING SAFETY DEFECTS IN THE UNITED STATES . . . . . . . . . . . 127 MOPAR ACCESSORIES AUTHENTIC ACCESSORIES BY MOPAR® . . . . . . . . . . . . . . . . . . . 128 INDEX . . . . . . . . . . . . . . . . . . 129 FAQ (How To?) FREQUENTLY ASKED QUESTIONS . . . 132 2 Information Provided by: INTRODUCTION/WELCOME WELCOME FROM CHRYSLER GROUP LLC Congratulations on selecting your new Chrysler Group LLC vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. Your new Chrysler Group LLC vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving. They can never take the driver's place. Always drive carefully. Your new vehicle has many features for the comfort and convenience of you and your passengers. Some of these should not be used when driving because they take your eyes from the road or your attention from driving. Never text while driving or take your eyes more than momentarily off the road. This guide illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This guide may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment described in this guide that are not available on this vehicle. Chrysler Group LLC reserves the right to make changes in design and specifications and/or make additions to or improvements to its products without imposing any obligation upon itself to install them on products previously manufactured. This User Guide has been prepared to help you quickly become acquainted with the important features of your vehicle. It contains most things you will need to operate and maintain the vehicle, including emergency information. The DVD includes a computer application containing detailed owner's information which can be viewed on a personal computer or MAC computer. The multimedia DVD also includes videos which can be played on any standard DVD player (Uconnect® Touch-Screen Radios). Additional DVD operational information is located on the back of the DVD sleeve. 3 Information Provided by: INTRODUCTION/WELCOME For complete owner information, refer to your Owner's Manual on the DVD in the owner's kit provided at the time of new vehicle purchase. For your convenience, the information contained on the DVD may also be printed and saved for future reference. Chrysler Group LLC is committed to protecting our environment and natural resources. By converting from paper to electronic delivery for the majority of the user information for your vehicle, together we greatly reduce the demand for tree-based products and lessen the stress on our environment. This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive enclosed vehicles were not intended. It handles and maneuvers differently from many passenger cars both on-road and off-road, so take time to become familiar with your vehicle. VEHICLES SOLD IN CANADA With respect to any vehicles sold in Canada, the name Chrysler Group LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution. WARNING! · Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. · Always make sure that objects cannot fall into the driver foot well while the vehicle is moving. Objects can become trapped under the brake pedal and accelerator pedal causing a loss of vehicle control. · Failure to properly follow floor mat installation or mounting can cause interference with the brake pedal and accelerator pedal operation causing loss of control of the vehicle. · Never use the `PARK' position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. · Refer to your Owner's Manual on the DVD for further details. 4 Information Provided by: INTRODUCTION/WELCOME Rollover Warning Use of Aftermarket Products (Electronics) The use of aftermarket devices including cell phones, MP3 players, GPS systems, or chargers may affect the performance of on-board wireless features including Keyless Enter-N-GoTM and Remote Start range. If you are experiencing difficulties with any of your wireless features, try disconnecting your aftermarket devices to see if the situation improves. If your symptoms persist, please see an authorized dealer. CHRYSLER, JEEP, MOPAR, ATF+4, COMMAND-TRAC, FREEDOM TOP, ROCK-TRAC, RUBICON, SAHARA, TRU-LOK, Uconnect and WRANGLER are registered trademarks of Chrysler Group LLC. COPYRIGHT ©2013 CHRYSLER GROUP LLC 5 Information Provided by: CONTROLS AT A GLANCE DRIVER COCKPIT 1. Electronic Vehicle Information Center (EVIC) Controls pg. 84 2. Turn Signal/Lights Lever (behind steering wheel) pg. 23 3. Electronic Vehicle Information Center (EVIC) Display 4. Instrument Cluster pg. 8 5. Wiper/Washer Lever (behind steering wheel) pg. 25 6. Audio System pg. 46 7. Power Windows 8. Climate Controls pg. 28 9. SWITCH PANEL · Heated Seats pg. 22 · Hazard Warning Light · Electronic Stability Control (ESC) OFF pg. 98 6 Information Provided by: CONTROLS AT A GLANCE 10. Glovebox 11. Power Outlet pg. 88 12. Shifter 13. 4WD Shifter Lever 14. Speed Control pg. 26 15. Ignition Switch 16. Tilt Steering Wheel pg. 21 17. Door Locks 7 Information Provided by: CONTROLS AT A GLANCE INSTRUMENT CLUSTER Warning Lights - Low Fuel Warning Light - Charging System Light** - Oil Pressure Warning Light** - Anti-Lock Brake (ABS) Light** - Air Bag Warning Light** - Electronic Throttle Control (ETC) Light - Tire Pressure Monitoring System (TPMS) Light - Engine Temperature Warning Light - Seat Belt Reminder Light BRAKE - Brake Warning Light** - Malfunction Indicator Light (MIL)** - Electronic Stability Control (ESC) Activation/Malfunction Indicator Light** (See page 96 for more information.) 8 Information Provided by: CONTROLS AT A GLANCE Indicators - Turn Signal Indicators - High Beam Indicator - Front Fog Light Indicator - Front Axle Lock Indicator* - Rear Axle Lock Indicator* - Vehicle Security Indicator* 4WD CRUISE - O/D (Overdrive) Off Indicator - 4WD Indicator* - Sway Bar Indicator* - Electronic Stability Control (ESC) Off Indicator - Cruise Indicator Odometer Messages ECO - Fuel Saver Indicator door - Door Ajar gASCAP - Fuel Cap Fault gATE* - Swing Gate Ajar noFUSE* - Fuse Fault LoW tirE* - Low Tire Pressure HOTOIL* - Transmission Temperature Warning Message CHAngE OIL* - Change Engine Oil * If equipped ** Bulb Check with Key On Information Provided by: 9 GETTING STARTED KEY FOB Locking And Unlocking The Doors/Swing Gate · Press the LOCK button once to lock all the doors and swing gate. Press the UNLOCK button once to unlock the driver's door only and twice within five seconds to unlock all the doors and swing gate. · All doors can be programmed to unlock on the first press of the UNLOCK button. Refer to Programmable Features in this guide. Panic Alarm · Press the PANIC button once to turn the panic alarm on. · Wait approximately three seconds and press the button a second time to turn the panic alarm off. 1 -- Unlock 2 -- Remote Start 3 -- Lock WARNING! · Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be severely injured or killed. Children should be warned not to touch the parking brake, brake pedal, or the shift lever. Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, A child could start the vehicle, operate power windows, other controls, or move the vehicle. · Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause them to be severely injured or killed. 10 Information Provided by: GETTING STARTED REMOTE START · Press the REMOTE START button x2 on the Key Fob twice within five seconds. Pressing the REMOTE START button a third time shuts the engine off. · To drive the vehicle, press the UNLOCK button, insert the key in the ignition and turn to the ON/RUN position. · With remote start, the engine will only run for 15 minutes (timeout) unless the ignition key is placed in the ON/RUN position. · The vehicle must be started with the key after two consecutive timeouts. WARNING! · Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause you or others to be severely injured or killed when inhaled. · Keep Key Fob transmitters away from children. Operation of the Remote Start System, windows, door locks or other controls could cause you and others to be severely injured or killed. THEFT ALARM To Arm: · Lock the door using either the power door lock switch (one door must be open) or the LOCK button on the Remote Keyless Entry (RKE) transmitter (doors can be open or closed), and close all doors. NOTE: The Vehicle Security Alarm will not arm if you lock the doors with the manual door lock plungers. · The Vehicle Security Light in the instrument cluster will flash for 16 seconds. This shows that the Vehicle Security Alarm is arming. During this period, if a door is opened, the ignition is cycled to ON/RUN, or the power door locks are unlocked in any manner, the Vehicle Security Alarm will automatically disarm. NOTE: · During the 16-second arming period, if a door is opened or the ignition is cycled to ON/RUN, the Vehicle Security Alarm will automatically disarm. · Once armed, the Vehicle Security Alarm disables the unlock switch on the driver door trim panel and passenger door trim panel. Information Provided by: 11 GETTING STARTED To Disarm The System: · Press the Key Fob UNLOCK button or cycle the ignition to the ON/START position. NOTE: The driver's door key cylinder button on the RKE transmitter cannot arm or disarm the Vehicle Security Alarm. · The Vehicle Security Alarm is designed to protect your vehicle; however, you can create conditions where the Vehicle Security Alarm will give you a false alarm. If one of the previously described arming sequences has occurred, the Vehicle Security Alarm will arm regardless of whether you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm. · If the Vehicle Security Alarm is armed and the battery becomes disconnected the Vehicle Security Alarm will remain armed when the battery is reconnected. The exterior lights will flash, and the horn will sound. If this occurs, disarm the Vehicle Security Alarm. SEAT BELT · Be sure everyone in your vehicle is in a seat and using a seat belt properly. · Position the lap belt across your thighs, below your abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision. · Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the belt. · A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. · A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. · A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after a collision if they have been damaged (bent retractor, torn webbing, etc.). 12 Information Provided by: GETTING STARTED · The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. · A deployed pretensioner or a deployed air bag must be replaced immediately. NOTE: When the ignition switch is first turned to the ON/RUN position, this light will turn on for four to eight seconds as a bulb check. During the bulb check, if the driver's seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Indicator Light will flash or remain on continuously. WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not buckled up properly. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle. Always be sure you and others in your vehicle are buckled up properly. SUPPLEMENTAL RESTRAINT SYSTEM (SRS) -- AIR BAGS · This vehicle has Advanced Front Air Bags for both the driver and right front passenger as a supplement to the seat belt restraint system. The Advanced Front Air Bags will not deploy in every type of collision. · Advanced Front Air Bags are designed to provide additional protection by supplementing the seat belts in certain frontal collisions depending on several factors, including the severity and type of collision. Advanced Front Air Bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. · This vehicle may be equipped with Supplemental Seat-Mounted Side Air Bags to provide enhanced protection to help protect an occupant during a side impact. · If the Air Bag Warning Light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized service center immediately. · Refer to the Owner's Manual on the DVD for further details regarding the Supplemental Restraint System (SRS). Information Provided by: 13 GETTING STARTED WARNING! · Relying on the air bags alone could lead to more severe injuries in a collision. The air bags work with your seat belt to restrain you properly. In some collisions, the air bags won't deploy at all. Always wear your seat belts even though you have air bags. · Being too close to the steering wheel or instrument panel during Advanced Front Air Bag deployment could cause serious injury, including death. Air bags need room to inflate. Sit back, comfortably extending your arms to reach the steering wheel or instrument panel. · Supplemental Seat-Mounted Side Air Bags need room to inflate. Do not lean against the door or window. Sit upright in the center of the seat. · Being too close to the Seat-Mounted Side Air Bag during deployment could cause you to be severely injured or killed. · Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will not be in place to protect you. · After any collision, the vehicle should be taken to an authorized dealer immediately. CHILD RESTRAINTS · Children 12 years or younger should ride properly buckled up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear seats rather than in the front. · Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. NOTE: · For additional information, refer to www.seatcheck.org or call 1866SEAT-CHECK (18667328243). · Canadian residents, should refer to Transport Canada's website for additional information: http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-index-53.htm 14 Information Provided by: GETTING STARTED LATCH -- Lower Anchors And Tethers For CHildren (Four-Door Models) · Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. · The rear outboard seating positions have lower anchors and top tether anchors. The rear center seating position has a top tether anchor only. LATCH -- Lower Anchors And Tethers For CHildren (Two-Door Models) · Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. · All rear seating positions have lower anchors and top tether anchors. · You may use the LATCH anchorage system until the combined weight of the child and the child restraint is 65 lbs (29.5 kg). Use the seat belt and tether anchor instead of the LATCH system once the combined weight is more than 65 lbs (29.5 kg). · The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seat- back, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion. Information Provided by: 15 GETTING STARTED · In addition, there are tether strap anchors located behind each rear seatback, near to the floor. Two-Door Models WARNING! This vehicle does not have a center seating position. Do not use the center lower LATCH anchorages to install a child seat in the center of the back seat. Four-Door Models · Do not install child restraints with rigid lower attachments in the center seating position. Only install this type of child restraint in the outboard seating positions. Child restraints with flexible, webbing mounted lower attachments can be installed in any rear seating position. In the center position, the inner anchorages are 19 inches (484 mm) apart. Installing The Child Restraint Using The LATCH Lower Anchors NOTE: Never "share" a LATCH anchorage with two or more child restraints. 1. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchorages. 2. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seating position. 3. If the child restraint has a tether strap, connect it to the top tether anchorage. See below for directions to attach a tether anchor. 4. Tighten all of the straps as you push the child restraint rearward and downward into the seat. Remove slack in the straps according to the child restraint manufacturer's instructions. 5. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. 16 Information Provided by: GETTING STARTED Installing The Child Restraints Using The Vehicle Seat Belts · The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint. Any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary. · Always use the tether anchor when using the seat belt to install a forward facing child restraint, up to the recommended weight limit of the child restraint. Installing The Top Tether Strap (With The Lower Anchors Or The Vehicle Seat Belt): · When installing a forward-facing child restraint, the top tether strap should always to be secured, up to the tether anchor weight limit, whether the child restraint is installed with the lower anchors or the vehicle seat belt. To Install A Child Seat Using An ALR: 1. Pull enough of the seat belt webbing from the retractor to pass it through the belt path of the child restraint. Do not twist the belt webbing in the belt path. 2. Slide the latch plate into the buckle until you hear a "click." 3. Pull on the webbing to make the lap portion tight against the child seat. 4. To lock the seat belt, pull down on the shoulder part of the belt until you have pulled all the seat belt webbing out of the retractor. Then, allow the webbing to retract back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode. 5. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any webbing. If the retractor is not locked, repeat the last step. 6. Finally, pull up on any extra webbing to tighten the lap portion around the child restraint while you push the child restraint rearward and downward into the vehicle seat. 7. If the child restraint has a top tether strap and the seating position has a top tether anchorage, connect the tether strap to the anchorage and tighten the tether strap. See below for directions to attach a tether anchor. 8. Test that the child restraint is installed tightly by pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) in any direction. Information Provided by: 17 GETTING STARTED Installing The Top Tether Strap (With Either Lower Anchors Or Vehicle Seat Belt): · When installing a forward-facing child restraint, the top tether strap should always to be secured, up to the tether anchor weight limit, whether the child restraint is installed with the lower anchors or the vehicle seat belt. 1. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. 2. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and between the two posts. If not possible, lower the head restraint and pass the tether strap around the outboard side of the head restraint. 3. Attach the tether strap hook of the child restraint to the top tether anchorage and remove slack in the tether strap according to the child restraint manufacturer's instructions. WARNING! · In a collision, an unrestrained child, even a tiny baby, can become a projectile inside the vehicle. The force required to hold even an infant on your lap could become so great that you could not hold the child, no matter how strong you are. The child and others could be severely injured or killed. Any child riding in your vehicle should be in a proper restraint for the child's size. · Rearward-facing child seats must never be used in the front seat of a vehicle with a front passenger air bag. An air bag deployment could cause severe injury or death to infants in this position. · Only use a rearward-facing child restraint in a vehicle with a rear seat. · Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be severely injured or killed. Follow the manufacturer's directions exactly when installing an infant or child restraint. · An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap. · If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap. 18 Information Provided by: GETTING STARTED FRONT SEATS Manual Seat Adjustment Forward/Rearward · Lift up on the adjusting bar located at the front of the seat near the floor and release it when the seat is at the desired position. Then, using body pressure, move forward and backward on the seat to be sure that the seat adjusters have latched. Height Adjustment · Ratchet the front lever, located on the outboard side of the seat, upward to raise the seat height. · Ratchet the lever downward to lower the seat height. Recliner · Lift the recliner lever located on the outboard side of the seat, lean back and release at the desired position. Driver's and Passenger Easy Entry Seats (Two-Door) · Push the lever on the seatback rear- ward (toward the rear of the vehicle) to tilt the entire seat forward. · To return the seat to a sitting position, rotate the seatback upright until it locks. Push the seat rearward until the track locks. Information Provided by: 19 GETTING STARTED NOTE: · If equipped with a combination lever, the seatback will return to its first locked position. The recliner handle will have to be actuated to adjust the seatback to the desired reclined position. · The front passenger seats have a track memory which returns the seat to just past the halfway point of the track, regardless of its original position. · The recliner and easy entry levers should not be used during the automatic returning of the seat to its fully upright position. WARNING! · Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted, and you could be severely injured or killed. Only adjust a seat while the vehicle is parked. · Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision, you could slide under the seat belt and be severely injured or killed. Use the recliner only when the vehicle is parked. REAR SEATS Folding Rear Seat · Be sure that the front seats are fully upright and positioned forward. This will allow the rear seat to fold down easily. To Fold The Rear Seat · Lift the seatback release lever and fold the seatback forward (two-door models). · Slowly flip the entire seat (two-door models) forward. To Raise The Rear Seat · Lift up on the seatback to return it to the upright position. 20 Information Provided by: GETTING STARTED WARNING! · It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be severely injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly. · Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause you or others to be severely injured or killed. TILT STEERING COLUMN · The tilt lever is located on the steering column, below the turn signal lever. · Push down on the lever to unlock the steering column. · With one hand firmly on the steering wheel, move the steering column up or down as desired. · Pull upward on the lever to lock the column firmly in place. WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving, or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your vehicle. Failure to follow this warning may result in you or others being severely injured or killed. Information Provided by: 21 GETTING STARTED HEATED SEATS Front Heated Seats · The controls for front heated seats are located near the bottom center of the instrument panel (below the heater/air conditioning controls). · Press the switch once to select Highlevel heating. Press the switch a second time to select Low-level heating. Press the switch a third time to shut the heating elements Off. · If the High-level setting is selected, the system will automatically switch to Lowlevel after approximately 30 minutes. The Low-level setting will turn Off automatically after approximately 30 minutes. WARNING! · Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions must exercise care when using the seat heater. It may cause burns even at low temperatures, especially if used for long periods of time. · Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat. 22 Information Provided by: OPERATING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS · A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. · Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. · While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. Wide-open throttle acceleration in low gear can be detrimental and should be avoided. · The engine oil installed in the engine at the factory is a high-quality energy conserving type lubricant. Oil changes should be consistent with anticipated climate conditions under which vehicle operations will occur. For the recommended viscosity and quality grades, refer to "Maintaining Your Vehicle". NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered a normal part of the break-in and not interpreted as an indication to an engine problem or malfunction. CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. TURN SIGNAL/LIGHTS LEVER Headlights/Parking Lights/Automatic Headlights · Rotate the end of the lever to the first detent for parking lights detent for headlights , and the third detent for AUTO. , the second · When set to AUTO, the system automatically turns the headlights on or off based on ambient light levels. Information Provided by: 23 OPERATING YOUR VEHICLE Instrument Panel Dimmer · Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. · Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the parking lights or headlights are on. · Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio controls when the parking lights or headlights are on. · Rotate the center portion of the lever upward to the last detent to turn on the interior lighting. Flash To Pass · Pull the lever toward you to activate the high beams. The high beams will remain on until the lever is released. High Beam Operation · Push the lever forward to activate the high beams. NOTE: For safe driving, turn off the high beams when oncoming traffic is present to prevent headlight glare and as a courtesy to other motorists. Fog Lights · Turn on the parking lights or low beam headlights and pull out the end of the lever. Turn Signals/Lane Change Assist · Tap the lever up or down once and the turn signal (right or left) will flash three times and automatically turn off. 24 Information Provided by: OPERATING YOUR VEHICLE WIPER/WASHER LEVER Front Wipers Intermittent, Low And High Operation · Rotate the end of the lever to the first detent position for one of five intermittent settings, the second detent for low wiper operation and the third detent for high wiper operation. Washer Operation · Pull the lever toward you and hold for as long as spray is desired. Mist · Pull down on the lever and release when a single wipe is desired. NOTE: The mist feature does not activate the washer pump; therefore, no washer fluid will be sprayed on the windshield. The wash function must be activated in order to spray the windshield with washer fluid. Rear Wiper Wiper Operation · Rotate the center portion of the lever forward to the first detent for rear wiper operation. Washer Operation · Rotate the center portion of the lever past the first detent to activate the rear washer. Information Provided by: 25 OPERATING YOUR VEHICLE SPEED CONTROL · The Electronic Speed Control switches are located on the steering wheel. Cruise ON/OFF · Push the ON/OFF switch to activate the Speed Control. · The cruise symbol will appear on the instrument cluster to indicate the Speed Control is on. · Push the ON/OFF switch a second time to turn the system off. Set · With the Speed Control on, push and release the SET button to set a desired speed. Accel/Decel · Once a speed is set, pushing the RES + button once or the SET button once will increase or decrease the set speed approximately 1 mph (1.6 km/h). · Push and hold the RES + button to accelerate in 5 mph (8 km/h) increments or push and hold the SET button to decelerate in 5 mph (8 km/h) increments; release the button to save the new set speed. Resume · To resume a previously selected set speed in memory, push the RES + button and release. Cancel · Push the CANCEL switch, or apply the brakes or clutch, to cancel the set speed and maintain the set speed memory. · Push the ON/OFF switch to turn the system off and erase the set speed memory. 26 Information Provided by: OPERATING YOUR VEHICLE MANUAL CLIMATE CONTROLS Air Recirculation · Use Recirculation for maximum A/C operation. · For window defogging, turn the recirculation button off. · Recirculation is allowed in floor and defrost/floor (mix modes) for approximately five minutes. Heated Mirrors · The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster. Information Provided by: 27 OPERATING YOUR VEHICLE AUTOMATIC TEMPERATURE CONTROLS (ATC) Automatic Operation · Turn the Mode and Blower Controls to the AUTO position. · Select the desired temperature by rotating the Temperature Control. · The system will maintain the set temperature automatically. Air Conditioning (A/C) · If the air conditioning button is pressed while in AUTO mode, the system will exit AUTO mode and stay in A/C. The mode and blower will go to the previous user setting. Air Recirculation · Use Recirculation for maximum A/C operation. · For window defogging, turn the recirculation button off. · If the recirculation button is pressed while in the AUTO mode, the indicator light may flash three times to indicate the cabin air is being controlled automatically. Heated Mirrors · The mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the defroster. 28 Information Provided by: OPERATING YOUR VEHICLE SUNRIDER® AND SOFT TOP 2Door Sunrider® Down · Follow these simple steps to open the Sunrider® feature. 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Slide the plastic sleeve forward. Information Provided by: 29 OPERATING YOUR VEHICLE 4. Grasp the header and lift the top back. Make sure the material is folded back as shown. 5. Locate the straps to secure the side bows. Wrap the straps around the bows as shown. Repeat on the other side. 6. Reposition the sun visors. NOTE: If you are going to be driving faster than 40 mph (64 km/h) with the Sunrider® feature open, it is recommended that you remove the rear window of the vehicle. · To close the Sunrider® feature, per- form the above steps in the opposite order. 30 Information Provided by: OPERATING YOUR VEHICLE 2Door Soft Top Down · Follow these simple steps to lower the 2door soft top. 1. Remove the side and back windows. 2. Remove rear corner panels. 3. Release header latches from the windshield frame. Information Provided by: 31 OPERATING YOUR VEHICLE 4. Release the Sunrider® latch (both sides). 5. Open the swing gate and lower the top. NOTE: Ensure the fabric does not overhang the sides of the vehicle. · To raise the soft top, perform the above steps in the opposite order. 32 Information Provided by: OPERATING YOUR VEHICLE 4Door Sunrider® Down · Follow these simple steps to open the Sunrider® feature. 1. Unclip and move the sun visors to the side. 2. Release the header latches from the loops on the windshield frame. 3. Grasp the front side bow behind the header, and lift the top. Information Provided by: 33 OPERATING YOUR VEHICLE 4. Fold the top so that the material forms a "W" as shown. Enter the vehicle and move the material into two folds. 5. Fold back the front section of the top and gently rest the header on top of the rear portion of the deck. 34 Information Provided by: OPERATING YOUR VEHICLE 6. Secure the top by using the two provided straps. Each strap will wrap around the side bow and Velcro® to itself; use one strap on each side of the vehicle. NOTE: · Failure to fold the fabric rearward will allow the material to sag and may block the rearview mirror. · If you are going to be driving faster than 40 mph (64 km/h) with the Sunrider® feature open, it is recommended that you remove the rear window of the vehicle. · To close the Sunrider® feature, perform the above steps in the opposite order. 4Door Soft Top Down · Follow these simple steps to lower the 4door soft top. 1. Remove the side and back windows. 2. Remove rear corner panels. 3. Release header latches from the windshield frame. Information Provided by: 35 OPERATING YOUR VEHICLE 4. Fold header rearward, pulling the fabric to the rear. 5. Fold the top so that the material forms a "W" as shown. Enter the vehicle and move the material into two folds. 6. Release Sunrider® latch (both sides). 36 Information Provided by: OPERATING YOUR VEHICLE 7. Open the swing gate and lower the top. NOTE: Ensure the fabric does not overhang the sides of the vehicle. · To raise the soft top, perform the above steps in the opposite order. CAUTION! · Do not run a fabric top through an automatic car wash. Window scratches and wax buildup may result. · Do not lower the top when the temperature is below 41°F (5°C). Damage to the top may result. · Do not lower the top when the windows are dirty. Grit may scratch the window. · Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered. · The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle and, thus, cannot properly carry any additional loads other than environmental (rain, snow, etc.). WARNING! · Do not drive the vehicle with the rear window curtain up unless the side curtains are also open. Dangerous exhaust gases which can kill could enter the vehicle. · The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts. Information Provided by: 37 OPERATING YOUR VEHICLE HARD TOP AND FREEDOM TOP® Freedom Top® Removal · Follow these simple steps to remove the front panels. 1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the overhead speaker bar assembly) counterclockwise until they can be removed. 3. Turn the center L-shaped locks (two) from the center of the roof panel. 38 Information Provided by: OPERATING YOUR VEHICLE 4. Turn the rear L-shaped lock (located above the shoulder belt anchorage). 5. Unlatch the header panel latch located at the top of the windshield. 6. Remove the left-hand panel. · To remove the right panel, follow the steps above except for Step 3. NOTE: · The left panel must be removed before removing right panel. · Vehicles equipped with a Freedom Top®, come with a Freedom Top® storage bag that allows you to store your Freedom Top® panels. Refer to the Owner's Manual on the DVD for details. Information Provided by: 39 OPERATING YOUR VEHICLE Hard Top Removal · Follow these simple steps to remove the hard top. 1. Remove both front panels. Refer to "Front Panel(s) Removal" above. 2. Open both doors. 3. Remove the two Torx® head screws that secure the hard top at the B-pillar (near the top of the door) using a #40 Torx® head driver (FourDoor Only). 4. Remove the six Torx® head screws that secure the hard top to the vehicle (along the interior bodyside) using a #40 Torx® head driver. 5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass. 6. Locate and disconnect the wire harness on the left rear inside corner of the vehicle. 7. Remove the washer hose (next to the wire harness) by pinching the grips on hose connector and pull downward. 8. Close the swing gate. 9. Remove the hard top from the vehicle. Place the hard top on a soft surface to prevent damage. CAUTION! · The front panel(s) must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicles interior. · The hard top assembly must be positioned properly to ensure sealing. Improper installation can cause water to leak into the vehicles interior. · The hard top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.). · Do not move your vehicle until the top has been either fully attached to the windshield frame and bodyside, or fully removed. · The removal of the hard top requires four adults located on each corner. Failure to follow this caution could damage the hard top. 40 Information Provided by: OPERATING YOUR VEHICLE DUAL TOP -- IF EQUIPPED · If your vehicle is equipped with a Dual Top, you must remove one of the tops from the vehicle. · 2 Door - If the soft top is removed, the pivot brackets must also be removed from the sport bar. · 4 Door - If the soft top is removed, ensure that the pivot bracket strap is installed onto the Soft Top pivot bracket before removing the soft top from the vehicle. Remove the fasteners between the Soft Top pivot bracket and the attach bracket to the sport bar. · The soft top was installed at the factory for shipping purposes only. NOTE: The soft top and the hard top are to be used independently. · Refer to the Understanding The Fea- tures Of Your Vehicle section of your vehicle's Owner's Manual on the DVD for further details. WIND BUFFETING · Wind buffeting can be described as a helicopter-type percussion sound. If buffeting occurs with the rear windows open, adjust the front and rear windows together. Information Provided by: 41 ELECTRONICS YOUR VEHICLE'S SOUND SYSTEM 1. Uconnect® Voice Command Button pg. 81 2. Uconnect® Phone Button pg. 78 3. Steering Wheel Audio Controls (Left) pg. 77 4. Volume Knob / Audio Mute Button 5. CD Eject Button 42 Information Provided by: ELECTRONICS 6. Steering Wheel Audio Controls (Right) pg. 77 7. Uconnect® Radio pg. 44 8. Tune / Scroll Knob / Browse / Enter Button 9. Audio Jack 10. USB Port, pg. 56 Information Provided by: 43 ELECTRONICS Uconnect® 130 NOTE: Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving. Clock Setting · Press and hold the "TIME" button until the hours blink; turn the "TUNE/ SCROLL" control knob to set the hours. · Press the "TUNE/SCROLL" control knob until the minutes begin to blink; turn the "TUNE/SCROLL" control knob to set the minutes. · Press the "TUNE/SCROLL" control knob to save the time change. · To exit, press any button/knob or wait five seconds. Equalizer, Balance And Fade · Press the "TUNE/SCROLL" control knob and "BASS" will display. Rotate the "TUNE/SCROLL" control knob to select the desired setting. Subsequent presses of the "TUNE/SCROLL" control knob will display, "MID RANGE," "TREBLE," "BALANCE" and "FADE". 44 Information Provided by: ELECTRONICS Radio Operation Seek Up/Down Buttons · Press to seek through radio stations in AM or FM bands. · Hold either button to bypass stations without stopping. Store Radio Presets · Press the "SET/RND" or "SET" (depending on the radio) button once and SET 1 will show in the display. Then select button (16). · A second station may be added to each push button. Press the "SET/RND" or "SET" (depending on the radio) button twice and SET 2 will show in the display. Then select button (16). CD/DISC Operation Seek Up/Down Buttons · Press to seek through CD tracks. · Hold either button to bypass tracks without stopping. SET/RND or RND (depending on radio) Button (Random Play) · Press this button while the CD is playing to activate Random Play. · This feature plays the selections on the CD in random order to provide an interesting change of pace. Audio Jack Operation · The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicle's sound system. This requires the use of a 3.5 mm stereo audio patch cable. · Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers. · The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device. Information Provided by: 45 ELECTRONICS Uconnect® 130 WITH SiriusXM SATELLITE RADIO NOTE: · Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating "Uconnect Phone not available" if you do not. · Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving. Clock Setting · Press and hold the "TIME" button until the hours blink; turn the "TUNE/ SCROLL" control knob to set the hours. · Press the "TUNE/SCROLL" control knob until the minutes begin to blink; turn the "TUNE/SCROLL" control knob to set the minutes. · Press the "TUNE/SCROLL" control knob to save the time change. · To exit, press any button/knob or wait five seconds. 46 Information Provided by: ELECTRONICS Equalizer, Balance And Fade · Press the "TUNE/SCROLL" control knob and "BASS" will display. Rotate the "TUNE/SCROLL" control knob to select the desired setting. Subsequent presses of the "TUNE/SCROLL" control knob will display, "MID RANGE," "TREBLE," "BALANCE" and "FADE". Radio Operation Seek Up/Down Buttons · Press to seek through radio stations in AM, FM, or SAT bands. · Hold either button to bypass stations without stopping. Store Radio Presets · Press the "SET/RND" or "SET" (depending on the radio) button once and SET 1 will show in the display. Then select button (16). · A second station may be added to each push button. Press the "SET/RND" or "SET" (depending on the radio) button twice and SET 2 will show in the display. Then select button (16). Music Type NOTE: The Music Type function only operates when in FM mode. · Press the "MUSIC TYPE" button to activate this mode. Press the "MUSIC TYPE" button again or turn the "TUNE/SCROLL" control knob to select the desired music type (Adult Hits, Country, Jazz, Oldies, Rock, etc.). · When a music type is chosen and the Music type is displayed, press either "SEEK" button and the radio will only search for stations with the selected music type. SETUP Button · Pressing the "SETUP" button allows you to select between items that are available in that particular mode. · Turn the "TUNE/SCROLL" control knob to scroll through the entries. Push the "AUDIO/SELECT" button to select an entry and make changes. SiriusXM Satellite Radio · SiriusXM Satellite Radio gives you over 130 channels, including 100% commercial-free music from nearly every genre, plus all your favorite sports, news, talk and entertainment channelsall with crystal clear, coast-to-coast coverage, all in one place and all at your fingertips. · To access SiriusXM Satellite Radio, press the "SAT" hard-key. Information Provided by: 47 ELECTRONICS CD/DISC Operation Seek Up/Down Buttons · Press to seek through CD tracks. · Hold either button to bypass tracks without stopping. SET/RND or RND (depending on radio) Button (Random Play) · Press this button while the CD is playing to activate Random Play. · This feature plays the selections on the CD in random order to provide an interesting change of pace. LIST Button · Press the "LIST" button to bring up a list of all folders on the CD. Scroll up or down the list by turning the "TUNE/SCROLL" control knob. · To select a folder from the list, press the "TUNE/SCROLL" control knob and the radio will begin playing the files contained in that folder. Audio Jack Operation · The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicle's sound system. This requires the use of a 3.5 mm stereo audio patch cable. · Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers. · The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device. 48 Information Provided by: Uconnect® 230 ELECTRONICS NOTE: · Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating "Uconnect Phone not available" if you do not. · Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving. Clock Setting · Press and hold the "TIME" button until the hours blink; turn the "TUNE/ SCROLL" control knob to set the hours. · Press the "TUNE/SCROLL" control knob until the minutes begin to blink; turn the "TUNE/SCROLL" control knob to set the minutes. · Press the "TUNE/SCROLL" control knob to save the time change. · To exit, press any button/knob or wait five seconds. Information Provided by: 49 ELECTRONICS Equalizer, Balance And Fade · Press the "TUNE/SCROLL" control knob and "BASS" will display. Rotate the "TUNE/SCROLL" control knob to select the desired setting. Subsequent presses of the "TUNE/SCROLL" control knob will display, "MID RANGE," "TREBLE," "BALANCE" and "FADE". Radio Operation Seek Up/Down Buttons · Press to seek through radio stations in AM, FM, or SAT bands. · Hold either button to bypass stations without stopping. Store Radio Presets · Press the "SET" button once and SET 1 will show in the display. Then select button (16). · A second station may be added to each push button. Press the "SET" button twice and SET 2 will show in the display. Then select button (16). Music Type NOTE: The Music Type function only operates when in FM mode. · Press the "MUSIC TYPE" button to activate this mode. Press the "MUSIC TYPE" button again or turn the "TUNE/SCROLL" control knob to select the desired music type (Adult Hits, Country, Jazz, Oldies, Rock, etc.). · Once a music type is chosen and the music type is displayed, press the SEEK button and the radio will only search for stations with the selected music type. SETUP Button · Pressing the "SETUP" button allows you to select between items that are available in that particular mode. · Turn the "TUNE/SCROLL" control knob to scroll through the entries. Push the "AUDIO/SELECT" button to select an entry and make changes. SiriusXM Satellite Radio · SiriusXM Satellite Radio gives you over 130 channels, including 100% commercial-free music from nearly every genre, plus all your favorite sports, news, talk and entertainment channelsall with crystal clear, coast-to-coast coverage, all in one place and all at your fingertips. · To access SiriusXM Satellite Radio, press the "SAT" hard-key. 50 Information Provided by: ELECTRONICS CD/DISC Operation Seek Up/Down Buttons · Press to seek through CD tracks. · Hold either button to bypass tracks without stopping. LIST Button · Press the "LIST" button to bring up a list of all folders on the CD. Scroll up or down the list by turning the "TUNE/SCROLL" control knob. · To select a folder from the list, press the "TUNE/SCROLL" control knob and the radio will begin playing the files contained in that folder. How To Load Multiple CDs/DVDs · Press the "LOAD" button and then press the button with the corresponding number (16) where the CD is being loaded. The radio will display "PLEASE WAIT" and prompt when to "INSERT DISC". · After the radio displays "INSERT DISC", insert the CD into the player. The radio display will show "LOADING DISC" when the disc is loading and "READING DISC" when the radio is reading the disc. · Press the eject button and then the corresponding number (16) to eject the desired disc. Audio Jack Operation · The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicle's sound system. This requires the use of a 3.5 mm stereo audio patch cable. · Pressing the AUX button will change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers. · The functions of the portable device are controlled using the device buttons, not the buttons on the radio. However, the volume may be controlled using the radio or portable device. Information Provided by: 51 ELECTRONICS Uconnect® 430/430N NOTE: · Your radio may not be equipped with the Uconnect® Voice Command and Uconnect® Phone features. To determine if your radio has these features, press the Voice Command button on the radio. You will hear a voice prompt if you have the feature, or see a message on the radio stating "Uconnect Phone not available" if you do not. · Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving. Clock Setting · Turn the radio on, then touch the screen where the time is displayed. · Touch the "USER CLOCK" soft-key (Navigation radio only). · To adjust the hours, touch either the "HOUR FORWARD" or "HOUR BACKWARD" soft-key. · To adjust the minutes, touch either the "MINUTE FORWARD" or "MINUTE BACKWARD" soft-key. · To save the new time setting, touch the screen where the word "Save" is displayed. 52 Information Provided by: ELECTRONICS Menu · Press the "MENU" hard-key to access the System Setup menu and the My Files menu. · Press the "MENU" hard-key in an active mode (SAT, CD, AUX, etc.) to change mode specific settings. Equalizer, Balance And Fade Audio Control Menu · Press the "AUDIO" hard-key on the right side of the radio. · Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The "CENTER" softkey resets the settings. · Touch the "Equalizer" soft-key and use either the arrow soft-keys or the sliders on the screen to adjust BASS, MID, and/or TREBLE. Display Settings · Press the "MENU" hard-key and touch the "Display Settings" soft-key to access the Display Settings menu. · Select the "Daytime Colors" soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors. · Select the "Nighttime Colors" soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors. · Select the "Auto Color Mode" soft-key to switch to automatic daytime/nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle. · Touch the "EXIT" soft-key to save your settings. Information Provided by: 53 ELECTRONICS Radio Operation · To access Radio Mode, touch the "RADIO" hard-key on the left side of the faceplate, then touch the "AM," "FM" or "SAT" soft-key at the top of the screen to select the band. Seek Up/Seek Down · Press the "Seek Up" or "Seek Down" soft-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping. Store Radio Presets · Select the radio band by touching either the "AM," "FM," or "SAT" soft-key. · Find the station to store by either pressing the "Seek Up" or "Seek Down" soft-keys, touching the "SCAN" soft-key, or by using the "DIRECT TUNE" soft-key. · Once the station is found, touch and hold one of the "PRESET" soft-keys in the list to the right, until the preset key flashes and the station text on the soft-key changes. NOTE: If the Presets are not visible on the right side of the screen, press the "Presets" soft-key. 54 Information Provided by: CD/DVD Disc Operation ELECTRONICS · Press the "MEDIA" hard key to display the media source tabs at the top of the screen. Select the source by touching the "HDD," "DISC," or "AUX" media source soft-key tab. NOTE: Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system. Insert a CD/DVD Disc · To insert a disc, press the "LOAD" hard-key. · With the printed side upwards, insert the disc into the disc slot of the radio. The radio pulls the disc in automatically and closes the flip screen. The radio selects the appropriate mode after the disc is recognized, and starts playing the first track. The display shows "Reading..." during this process. Seek Up/Seek Down · Press the "Seek Up" or "Seek Down" hard-keys to seek through tracks in Disc Mode. Holding the "SEEK UP" soft-key will fast forward through the track until the beginning of the track is reached; if still held it will fast-forward through the next sequential track(s) (if random play node not active) until released. Holding the "SEEK DOWN" soft-key will fast- reverse through the track until the beginning of the track is reached; if still held it will fast-reverse through the next sequential track(s) (if random play node not active) until released. Information Provided by: 55 ELECTRONICS Audio Jack Operation · The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicle's sound system. This requires the use of a 3.5 mm stereo audio patch cable. · Press the "MEDIA" hard-key then the "AUX" soft-key to change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers. · The functions of the portable device are controlled using the device itself, not the buttons on the radio. However, the volume may be controlled using the radio or portable device. Hard Disk Drive (HDD) Operation · The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal hard disk drive. It functions similar to a CD player, with the exception that the internal HDD can hold more tracks. · It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen. · Before using the HDD mode, you will need to copy songs and pictures to the internal hard drive. Songs and pictures can be added to the hard drive by using a CD or USB device (e.g. thumb drive or memory stick). NOTE: · HDD supports only .jpg/JPEG formats for photos. · WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See the Uconnect® 430/430N User's Manual for more information. Copying Music From CD · Press the "LOAD" hard-key. · Insert a disc, then press the "MY FILES" hard-key and then select the "MY MUSIC" soft-key. · Touch the "Add Music Files to HDD" soft-key, then touch the "Disc" soft-key in the next screen to start the process. NOTE: · You might need to select the folder or title depending on the CD, then press "DONE" to start the copy process. · The copy progress is shown in the lower left corner of the screen. 56 Information Provided by: ELECTRONICS Copying Music From USB · The USB port on the radio face plate allows you to copy files to your hard drive. To access, lift up on the cover. · Insert a USB device (e.g. thumb drive or memory stick), then select "MY MUSIC soft-key." · Touch the "Add Music Files to HDD" soft-key, then touch the "Front USB" soft-key in the next screen. · Select the folders or titles you would like to copy, then touch the "SAVE" soft-key to start the copy process. · To copy all of the titles, touch the "ALL" soft-key then touch the "SAVE" soft-key NOTE: The copy progress is shown in the lower left corner of the screen. Copying Pictures To The HDD · Insert either a CD or a USB device containing your pictures in JPEG format. · Press the "MY FILES" hard-key. · Touch the "My Pictures" soft-key to get an overview of the currently stored images, then touch the "Add" soft-key. · Touch the "Disc" or "USB" soft-key, then select the folders or pictures you wish to copy to the HDD. Use the "PAGE" soft-keys to page through the list of pictures. · Touch the desired pictures or press the "All" soft-key for all pictures. Confirm your selections by touching the "SAVE" soft-key. NOTE: The copy progress is shown in the lower left corner of the screen. Information Provided by: 57 ELECTRONICS Display A Picture On The Radio Screen · Once the import is complete, the pictures will then be available in the "MY PICTURES" screen. · Press the "MY FILES" hard-key, then touch the "My Pictures" soft-key. Touch the desired picture, then touch the "Set as Picture View" soft-key and then touch the "Exit" soft-key. Lastly press the "MENU" hard-key and then touch the "Picture View" soft-key to display the chosen picture on the radio screen. NOTE: · A check mark in the My Pictures screen indicates the currently used picture. · You can also delete pictures by touching the "Delete" soft-key. Playing Music From The HDD · Press the "MEDIA" hard-key to display the media source tabs at the top of the screen. Touch the "HDD" soft-key tab. Touch the desired track soft-key to play or touch the "SEARCH/BROWSE" soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites. Cleaning Your Touch-Screen Radio · Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touch-screen. · If necessary, use a lint-free cloth dampened with a cleaning solution such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Always follow the solvent manufacturer's precautions and directions. 58 Information Provided by: ELECTRONICS Garmin® Navigation · Uconnect® 430N integrates Garmin's consumer-friendly navigation into your vehicle. Garmin® Navigation includes a database with over six million points of interest. · Touch the "NAV" soft-key in the upper right corner of the screen to access the Navigation system. Changing the Navigation Voice Prompt Volume 1. Program a destination. 2. While traveling on your route, touch the upper left area of the map screen where your next turn is displayed. 3. The Navigation system will then repeat the distance to your next turn. 4. While the Navigation system is speaking, use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level. Please note the volume setting for Navigation Voice Prompt is different than the audio system. NOTE: For your own safety and the safety of others, it is not possible to use certain features while the vehicle is in motion. Main Navigation Menu Finding Points Of Interest · From the main Navigation menu, touch the "Where To?" soft-key, then touch the "Points of Interest" soft-key. · Select a Category, then a subcategory, if necessary. · Select your destination and touch the "Go" soft-key. Information Provided by: 59 ELECTRONICS Finding A Place By Spelling The Name · From the Main Navigation Menu touch the "Where To?" soft-key. Next, touch the "Points of Interest" soft-key then touch the "Spell Name" soft-key. · Enter the name of your destination. · Touch the "Done" soft-key. · Select your destination and touch the "Go" soft-key. Entering A Destination Address · From the main Navigation menu touch the "Where To?" soft-key, then touch the "Address" soft-key. · Follow the on-screen prompts to enter the address then touch the "Go" soft-key. Setting Your Home Location · From the main Navigation menu touch the "Tools" icon. Next select the "My Data" folder icon. Then select "Set Home Location." · You may enter your address directly, use your current location as your home address, or choose from recently found locations. Edit Home Location · From the main Navigation menu touch the "Where To?" soft-key, then touch the "Tools" icon. Next, touch the "My Data" folder. · You may enter a new address directly, use your current location or choose from recently found locations. Go Home · A Home location must be saved in the system. From the Main Navigation menu, touch the "Where To?" soft-key, then touch the "Go Home" soft-key. 60 Information Provided by: ELECTRONICS Following Your Route · Your route is marked with a magenta line on the map. If you depart from the original route, your route is recalculated. A speed limit icon could appear as you travel on major roadways. Adding A Via Point · To add a stop between the current location and the end destination (Via Point) you must be navigating a route. · Touch the "back arrow" icon multiple times to return to the Main Navigation menu. · Touch the "Where To?" soft-key, then search for the additional stop. Select the destination you wish to add from the given search results. · Touch the "Go" soft-key, then touch "Add as a Via Point" soft-key and press the "Done" soft-key. Taking A Detour · To take a detour you must be navigating a route. · Touch the "back arrow" icon soft-key multiple times to return to the Main Navigation menu. · Touch the "Detour" soft-key. NOTE: If the route you are currently taking is the only reasonable option, the device might not calculate a detour. Information Provided by: 61 ELECTRONICS Acquiring Satellites · The GPS Satellite strength bars indicate the strength of your satellite reception. · Acquiring satellite signals can take a few minutes. When at least one of the bars is green, your device has acquired satellite signals. · You may experience delays receiving satellite signals when in areas with an obstructed view to the sky, such as garages, tunnels, or large cities with tall buildings. Uconnect® 730N NOTE: Your radio has many features that add to the comfort and convenience of you and your passengers. Some of these radio features should not be used when driving because they take your eyes from the road or your attention from driving. Clock Setting · Turn the radio on, then touch the screen where the time is displayed. · Touch the "USER CLOCK" soft-key. · To adjust the hours, touch either the "HOUR FORWARD" or "HOUR BACKWARD" soft-key. · To adjust the minutes, touch either the "MINUTE FORWARD" or "MINUTE BACKWARD" soft-key. · To save the new time setting, touch the screen where the word "Save" is displayed. 62 Information Provided by: ELECTRONICS Menu · Press the "MENU" hard-key to access the System Setup menu and the My Files menu. · Press the "MENU" hard-key in an active mode (SAT, CD, AUX, etc.) to change mode specific settings. Equalizer, Balance And Fade Audio Control Menu · Press the "MENU" hard-key on the right side of the radio. Then press the "Audio Control" soft-key to get to the audio control menu. · Use either the arrow soft-keys or the cross-hair on the screen to change Balance and Fade. The "CENTER" softkey resets the settings. · Touch the "Equalizer" soft-key and use either the arrow soft-keys or the sliders on the screen to adjust BASS, MID, and/or TREBLE. Display Settings · Press the "MENU" hard-key and touch the "Display Settings" soft-key to access the Display Settings menu. · Select the "Daytime Colors" soft-key to switch to manual daytime mode and to adjust the brightness of the display using daytime colors. · Select the "Nighttime Colors" soft-key to switch to manual nighttime mode and to adjust the brightness of the display using nighttime colors. · Select the "Auto Color Mode" soft-key to switch to automatic daytime/ nighttime mode and to control the brightness of the display using the dimmer switch of the vehicle. · Touch the "EXIT" soft-key to save your settings. Information Provided by: 63 ELECTRONICS Radio Operation · To access Radio Mode, touch the "RADIO/MEDIA" hard-key on the left side of the faceplate repeatedly until AM/FM/SAT appears at the top of the screen, then touch the "AM," "FM" or "SAT" soft-key to select the band. Seek Up/Seek Down · Press the "Seek Up" or "Seek Down" hard-keys to seek through radio stations in AM, FM, or SAT bands. Hold either Seek to bypass stations without stopping. Store Radio Presets · Select the radio band by touching either the "AM," "FM," or "SAT" soft-key. · Find the station to store by either pressing the "Seek Up" or "Seek Down" hard-keys, touching the "SCAN" soft-key, or by using the "DIRECT TUNE" soft-key. · Once the station is found, touch and hold one of the PRESET soft-keys in the list to the right, until you hear a confirmation beep. NOTE: If the Presets are not visible on the right side of the screen, press the "Presets" soft-key. 64 Information Provided by: CD/DVD Disc Operation ELECTRONICS · Press the "RADIO/MEDIA" hard-key until the media source tabs are displayed at the top of the screen. Select the source by touching the "HDD," "DISC," or "AUX" media source soft-key tab. NOTE: Your Touch-Screen Radio will usually automatically switch to the appropriate mode when something is first connected or inserted into the system. Insert a CD/DVD Disc · To insert a disc, press the "OPEN/CLOSE" hard-key. · With the printed side upwards, insert the disc into the disc slot of the radio. The radio pulls the disc in automatically and closes the flip screen. The radio selects the appropriate mode after the disc is recognized, and starts playing the first track. The display shows "Reading..." during this process. Seek Up/Seek Down · Press the "Seek Up" or "Seek Down" hard-keys to seek through tracks in Disc Mode. Hold either Seek to bypass tracks without stopping. Information Provided by: 65 ELECTRONICS Audio Jack Operation · The AUX/Audio Jack provides a means to connect a portable audio device, such as an MP3 player or an iPod®, to the vehicle's sound system. This requires the use of a 3.5 mm stereo audio patch cable. · Press the "RADIO/MEDIA" hard-key, then the "AUX" soft-key to change the mode to auxiliary device if the Audio Jack is connected, allowing the music from your portable device to play through the vehicle's speakers. · The functions of the portable device are controlled using the device itself, not the buttons on the radio. The volume may be controlled using the radio or portable device. Hard Disk Drive (HDD) Operation · The Hard Disk Drive (HDD) mode gives you access to the audio files on the internal hard disk drive. It functions similar to a CD player, with the exception that the internal HDD can hold more tracks. · It is also possible to import display pictures to the internal hard disk drive. The pictures can be displayed on the right half of the radio screen. · Before using the HDD mode, you will need to copy songs and pictures to the internal hard drive. Songs and pictures can be added to the hard drive by using a CD or USB device (e.g. thumb drive or memory stick). NOTE: · HDD supports only .jpg/JPEG formats for photos. · WMA/MP3 Files and Selective Songs from a CD can also be added to the HDD. See the Uconnect® 730N Supplement Manual for more information. Copying Music From CD · Press the "OPEN/CLOSE" hard-key. · Insert a disc, then press the "MENU" hard-key. · Touch the "MY FILES" soft-key, then select "MY MUSIC." 66 Information Provided by: ELECTRONICS · Touch the "Add Music Files to HDD" soft-key, then touch the "From Disc" soft-key in the next screen to start the process. NOTE: · You might need to select the folder or title depending on the CD, then press "Done" to start the copy process. · The copy progress is shown in the lower left corner of the screen. Copying Music From USB · The USB port on the radio face plate allows you to copy files to your hard drive. To access, lift up on the cover. · Insert a USB device (e.g. thumb drive or memory stick), then select "MY FILES." · Touch the "MY MUSIC" soft-key, then touch the "Add Music Files" to HDD soft-key. · Touch the "From USB" soft-key, then select the folders or titles you would like to copy, and then touch the "SAVE" soft-key to start the copy process. NOTE: The copy progress is shown in the lower left corner of the screen. Information Provided by: 67 ELECTRONICS Copying Pictures To The HDD · Insert either a CD or a USB device containing your pictures in JPEG format. · Press the "MENU" hard-key to access the Settings Menu, then touch the "My Files" soft-key. · Touch the "My Pictures" soft-key to get an overview of the currently stored images, then touch the "Add" soft-key. · Touch the "From Disc" or "From USB" soft-key, then select the folders or pictures you wish to copy to the HDD. Use the "PAGE" soft-keys to page through the list of pictures. · Touch the desired pictures or press the "All" soft-key for all pictures. Confirm your selections by touching the "SAVE" soft-key. NOTE: The copy progress is shown in the lower left corner of the screen. Display A Picture On The Radio Screen · Once the import is complete, the pictures will then be available in the "MY PICTURES" screen. · Press the "MENU" hard-key to access the Settings Menu, then touch the "My Files" soft-key and then touch the "My Pictures" soft-key. Touch the desired picture, then touch the "Set as Picture View" soft-key and then touch the "Exit" soft-key. Lastly press the "MENU" hard-key and then touch the "Picture View" soft-key to display the chosen picture on the radio screen. NOTE: · A check mark in the My Pictures screen indicates the currently used picture. · You can also delete pictures by touching the "Delete" soft-key. 68 Information Provided by: ELECTRONICS Playing Music From The HDD · Press the "RADIO/MEDIA" hard-key until the media source tabs are displayed at the top of the screen. Touch the "HDD" soft-key tab. Touch the desired track soft-key to play or touch the "SEARCH/BROWSE" soft-key to search by artist, by album, by song, by genre, from a folder, or from Favorites. Cleaning Your Touch-Screen Radio · Do not spray any liquid or caustic chemicals directly on the screen. Use a clean and dry micro fiber lens cleaning cloth to clean the touch-screen. · If necessary, use a lint-free cloth dampened with a cleaning solution such as isopropyl alcohol or an isopropyl alcohol and water solution ratio of 50:50. Always follow the solvent manufacturer's precautions and directions. NAVIGATION · Your navigation system receives GPS signals from up to 16 satellites to display the position of your vehicle. Map and database information is supplied through a hard disk drive. · Touch the "NAV" hard-key on the radio face plate to access the Navigation system and the NAV Main Menu. Information Provided by: 69 ELECTRONICS Changing the Navigation Guidance Prompt Volume 1. From the Navigation Map screen, touch the Menu hard-key then touch the "NAV Settings" soft-key. Next select "Guidance Prompts." 2. Select and adjust the navigation guidance prompt volume using the left and right arrows. 3. Touch the "SAMPLE VOL" soft-key to listen to the current volume setting. 4. Once satisfied with the volume, touch the "SAVE" soft-key to save the settings. Touch the "CANCEL" soft-key to exit the menu without saving the settings. NOTE: For your own safety and the safety of others, it is not possible to use the certain features while the vehicle is in motion. Main Navigation Menu Finding Points Of Interest · From the NAV main menu, touch the "Points of Interest" soft-key. · Select a Category and then a subcategory, if necessary. · Select your destination and touch "GO." 70 Information Provided by: ELECTRONICS Finding A Place By Entering The Street Address NOTE: Tip: Entering the city or zip code before entering the street name facilitates address entry. If the State and/or Country displayed are incorrect, touch the corresponding soft-key to make the correction. · From the NAV main menu, touch "New Destination," then touch "Street Address." · Once the Country and State are set and the Street Address screen is displayed, begin spelling the street name in the speller. In the upper right corner the number of possible roads decreases. · Touch the "LIST" soft-key to display a list of possible street names. Select the correct street name. · Next input the number. · In the Confirm Route screen the navigation radio displays the complete address, a map of the destination area, and the current routing method for you to verify. · Touch the "GO" soft-key to activate the route guidance. Entering Your Home Location · Press the "NAV" hard-key on the right side of the radio. · From the Nav Main Menu, touch "Guide Me Home" to enter your home address. If no home address has been set, touch "YES" to access the Enter Home Address menu. · Touch "Street Address" to enter your address. Touch the soft-key with your state's name and enter your street name into the speller. · Once the street name has been input, touch "CONTINUE" to confirm. Enter the house number into the next screen. If more than one city has this address, you will then need to select your city from a list. · Once the address is entered completely, the system shows a map of your home address area. Touch "SAVE" to confirm the address. The system will then ask if you want to go there. Touch the "Yes" or "No" soft-key. Change Home Address NOTE: Tip: Entering the city or zip code before entering the street name facilitates address entry. · This procedure will allow you to change your Home Address if one has already been entered. · Press the "MENU" hard-key, touch "My Files" and then touch "My Address Book." · Touch "Home," then touch "Edit Contacts" and then "Change Address." · Touch the soft-key with your state's name and enter your street name into the speller. Information Provided by: 71 ELECTRONICS · Once the street name has been input, touch "CONTINUE" to confirm. · Enter the house number into the next screen. If more than one city has this address, you will then need to select your city from a list. · Touch the "SAVE" soft-key to confirm the address. Go Home · From the NAV main menu, touch "Guide Me Home" when you want to route to your home destination. Where Am I Now? · From the NAV main menu, touch "Where Am I Now?" The Where Am I Now? menu displays location information for the current vehicle position. · Touch the "NEARBY POI" soft-key to search for a local Point of Interest. · Touch the "SAVE LOCATION" soft-key to save the current location in the Saved Locations memory. Route Guidance · After starting route guidance, the system calculates the route and announces: "Follow the arrows on the display." You will receive navigation recommendations by voice messages and screen displays. 72 Information Provided by: ELECTRONICS Route Options · After pressing the "OPTIONS" soft-key in the Route Guidance Menu, the following information is displayed: · In the left half of the screen, the current position and the current routing method are displayed. · "Take Detour" will allow you to calculate a different route. · "Find Nearby POI" to search for a local POI. · "Destination Info" displays destination information. · "View Turn List" lists streets utilized for the current route. · "Save Destination" to save the destination address. · "Change Method" will allow you to change the routing method. SiriusXM SATELLITE RADIO/TRAVEL LINK · SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase. · SiriusXM Travel Link is only available in the United States. · The following describes features that are available when in SiriusXM Satellite Radio mode. · To access SiriusXM Satellite Radio, press the "RADIO/MEDIA" or "RADIO" and then touch the "SAT" soft-key tab. Info · Touch the "i" soft-key to view detailed information about the current Sirius XM Satellite channel. SiriusXM Parental Controls · SiriusXM offers the option to permanently block selected channels. Call 1-888-539-7474 and request the Family Package. · Uconnect® 430/430N and 730N: Press the "MENU" hard-key while in SiriusXM Satellite Radio Mode, then touch the "Channel Lock" to enable and/or disable desired channels. The SEEK and SCAN function will then only display channels without Channel lock. Information Provided by: 73 ELECTRONICS Search/Browse · Touch the "magnifying glass" soft-key to search/browse the SiriusXM channel listing by Favorites and Categories such as Song, Artist and Channel Name. The Search/Browse also allows you manage your Favorites. SiriusXM Satellite Radio Favorites (SAT Favorites) · You can save 50 favorite songs and 50 favorite artists. · Touch the "Add Favorite" soft-key to add either the song or the artist of the currently playing program to the SAT Favorites list. The favorite star will appear in the upper right corner, below the "SAT" soft-key. · You will see a favorite star indicator in the upper right side of the screen below the "SAT" soft-key and a pop up will alert you that a favorite song or artist is currently playing on one of the SiriusXM satellite radio channels. NOTE: Refer to your Uconnect® 730N or 430/ 430N Supplement Manual for more information. 74 Information Provided by: ELECTRONICS Display SAT Favorites List · Touch the "Search/Browse" soft-key and select "Favorites" from the SAT Browse screen. · Touch the desired favorites soft-key to switch the SAT tuner to the corresponding channel. · You may use the "LIST" soft-key to toggle between: · Favorite Songs · Favorite Artists · Currently playing favorites Replay · While you are in SAT mode, you can replay 44 minutes of the current SiriusXM channel (when the channel is changed, this audio buffer is erased). Press the REPLAY button to listen to the stored audio. · You can touch the on-screen controls to pause and rewind audio playback, touch the SCAN button to preview each of the tracks stored in the buffer, or select a track from the list. · The time displayed below the bar indicates how much time is present between the current buffer play position and the live broadcast. Replay Option Option Description Play/Pause Touch to pause content playback. Touch Pause/Play again to resume playback. Rewind/RW Rewinds the channel content in steps of five seconds. Touch and hold to rewind continuously, then release to begin playing content at that point. Fast Forward/FW Forwards the content, and works similarly to Rewind/RW. However, Fast Forward/FW can only be used when content has been previously rewound. Replay Time Displays the amount of time in the upper center of the screen by which your content lags the live channel. Live Resumes playback of live content at any time while replaying re- wound content. Information Provided by: 75 ELECTRONICS SiriusXM Travel Link (Uconnect® 730N & Uconnect® 430N Only) NOTE: · SiriusXM Travel Link requires a subscription, sold separately after the 1 year trial subscription included with your vehicle purchase. · SiriusXM Travel Link is only available in the United States. · SiriusXM Travel Link brings a wealth of useful information into your vehicle and right to your fingertips. · To access Travel Link, press the MENU hard-key, then the Travel Link soft-key. 1 Favorites 2 Forecast 3 Ski Info 4 Fuel Prices 5 Movies 6 Sports View and store your favorite location, theater and sport teams for quick access. View detailed weather conditions, forecasts and ski/snowboarding conditions at resorts. View ski and snowboarding conditions at ski resorts. View detailed price information for fuel stations. View information on movies that are playing at theaters. View sports scores and upcoming events for all major sports. 76 Information Provided by: ELECTRONICS STEERING WHEEL AUDIO CONTROLS · The steering wheel audio controls are located on the rear surface of the steering wheel. Right Switch · Press the switch up or down to increase or decrease the volume. · Press the button in the center to change modes AM/FM/CD/SAT. Left Switch · Press the switch up or down to search for the next listenable station or select the next or previous CD track. · Press the button in the center to select the next preset station (radio) or to change CDs if equipped with a CD Changer. iPod®/USB/MP3 CONTROL · There are many ways to play music from iPod®/MP3 players or USB devices through your vehicle's sound system. · The remote USB port, located within the center console, allows you to plug an iPod® into the vehicle's sound system. NOTE: If equipped with the Uconnect® 730N or 731N the USB port on the faceplate allows the same functions as the remote USB port. · Non-Touch-Screen Radios: To hear audio from devices connected to the USB port, press the "AUX" button on the radio face plate · Touch-Screen Radios: To hear audio from devices connected to the USB port, press the "MEDIA" hard-key, then touch the "AUX" or "iPod®" soft-key. · When connected to this feature: · The iPod® can be controlled using the radio buttons to Play, Browse, and List the iPod® or external devices contents. · The iPod® battery charges when plugged into the USB port (if supported by the specific audio device). · Compatible iPod® devices may also be controllable using voice commands. Refer to the Owner's Manual on the DVD for details. Information Provided by: 77 ELECTRONICS NOTE: The USB port supports certain Mini, Classic, Nano, Touch, and iPhone® devices. The USB port also supports playing music from compatible external USB Mass Storage Class memory devices. For supported audio file formats, refer to the USB Port section in the Owner's Manual on the DVD. Refer to www.UconnectPhone.com website for a list of tested iPod®s. Some iPod® software versions may not fully support the USB port features. Please visit Apple's website for iPod® software updates. WARNING! Do not plug in or remove the iPod® or external device while driving. Failure to follow this warning could result in a collision. Uconnect® Phone · To determine if your vehicle is equipped with Uconnect® Phone, press the "Uconnect® Phone" button located on the radio faceplate. If your vehicle has this feature, you will hear a voice prompt. If not, you will see a message on the radio "Uconnect® Phone not available." · The Uconnect® Phone is a voice-activated, hands-free, in-vehicle communications system with Voice Command Capability (see Voice Command section). NOTE: To access the tutorial, press the "Uconnect® Phone" button . After the BEEP, say "tutorial." Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the "tutorial." · The Uconnect® Phone allows you to dial a phone number with your mobile phone using simple voice commands. · Refer to your vehicle Owner's Manual on the DVD for further details. NOTE: The Uconnect® Phone requires a mobile phone equipped with the Bluetooth® Hands-Free Profile, Version 1.0 or higher. For Uconnect® Customer Support: U.S. residents - visit www.UconnectPhone.com or call 18778558400. Canadian residents - visit www.UconnectPhone.com or call, 1-800-4652001 (English) or 1-800-387-9983 (French). This site will provide specific instructions based on the type of mobile phone being paired. 78 Information Provided by: ELECTRONICS Phone Pairing NOTE: Pairing is a one - time initial setup before using the phone. Prior to starting the pairing procedure ensure all additional phones within the vehicle have their Bluetooth® disabled. · Press the "Phone" button to begin. · Wait for the "ready" prompt and BEEP. · After the BEEP, say "setup" or "Uconnect device setup." · After the BEEP, say "device pairing." · After the BEEP, say "pair a device." · Follow the audible prompts. · You will be asked to say a four-digit Personal Identification Number (PIN), which you will later need to enter into your mobile phone. You can say any four-digit PIN. You will not need to remember this PIN after the initial pairing process. · You will then be prompted to give the phone pairing a name (each phone paired should have a unique name). · Next you will be asked to give this new pairing a priority of 1 through 7 (up to seven phones may be paired); 1 is the highest and 7 is the lowest priority. The system will only connect to the highest priority phone that exists within the proximity of the vehicle. · You will then need to start the pairing procedure on your cell phone. Follow the Bluetooth® instructions in your cell phone Owner's Manual to complete the phone pairing setup. Information Provided by: 79 ELECTRONICS Phonebook Phonebook Download Automatic Phonebook Transfer From Mobile Phone · If equipped and specifically supported by your phone, Uconnect® Phone automatically downloads names (text names) and number entries from your mobile phone's phonebook. Specific Bluetooth® Phones with Phone Book Access Profile may support this feature. Automatic Transfer is indicated by a green arrow at the bottom of the screen. See www.UconnectPhone.com for supported phones. · Automatic download and update, if supported, begins as soon as the Bluetooth® wireless phone connection is made to the Uconnect® Phone. For example, after you start the vehicle. NOTE: The mobile phone may require authorization prior to download. · A maximum of 1000 entries per phone will be downloaded and updated every time a phone is connected to the Uconnect® Phone. · Depending on the maximum number of entries downloaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, the previously downloaded phonebook is available for use. · Only the phonebook of the currently connected mobile phone is accessible. · Only the mobile phone's phonebook is downloaded. The SIM card phonebook is not part of the Mobile phonebook. · This downloaded phonebook cannot be edited or deleted on the Uconnect® Phone. These can only be edited on the mobile phone. The changes are transferred and updated to Uconnect® Phone on the next phone connection. Making A Phone Call · Press the "Phone" button . · After the BEEP, say "dial" (or "call" a name). · After the BEEP, say number (or name). Receiving A Call Accept (And End) · When an incoming call rings/is announced on Uconnect®, press the Phone button . · To end a call, press the Phone button . Mute (Or Unmute) Microphone During Call · During a call, press the "Voice Command" button . · After the BEEP, say "mute" (or "mute off"). 80 Information Provided by: ELECTRONICS Transfer Ongoing Call Between Handset And Vehicle · During a call, press the "Voice Command" button . · After the BEEP, say "transfer call." Changing The Volume · Start a dialogue by pressing the "Phone" button during a normal call. , then adjust the volume · Use the radio ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the Uconnect® system is speaking. Please note the volume setting for Uconnect® is different than the audio system. WARNING! · Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing you and others to be severely injured or killed. · In an emergency, to use Uconnect® Phone, your mobile phone must be: · turned on, · paired to Uconnect® Phone, · and have network coverage. Uconnect® VOICE COMMAND Voice Command Operation · The Uconnect® Voice Command system allows you to control your AM, FM radio, satellite radio, disc player, HDD, Uconnect® Phone, a memo recorder, and supported portable media devices. · When you press the "Voice Command" button located on the radio faceplate or steering wheel, you will hear a beep. The beep is your signal to give a command. If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the "Voice Command" button , listen for the BEEP, and say your command. NOTE: Visit http://www.driveuconnect.com/features/voiceCommand/ for more info on which voice command features apply to your vehicle. Information Provided by: 81 ELECTRONICS · Start a dialogue by pressing the "Voice Command" button , you will hear a beep. The beep is your signal to give a command. Below are a list of voice commands for each of the different modes. Common Voice Commands (Examples) While In: Main Menu Radio Mode SiriusXM Satellite Radio Mode Disc Mode Voice Command Example: "Radio AM" (to switch to the AM radio mode) "Radio FM" (to switch to the FM radio mode) "Satellite Radio" (to switch to the Satellite radio mode) "Disc" (to switch to the disc mode) "USB" (to switch to the USB mode) "Bluetooth Streaming" (to switch to the Bluetooth Streaming mode) "Memo" (to switch to the memo recorder) "System Setup" (to switch to system setup) "Frequency" (to change the frequency) "Next Station" (to select the next station) "Previous Station" (to select the previous station) "Radio Menu" (to switch to the radio menu) "Main Menu" (to switch to the main menu) "Channel Number" (to change the channel by its spoken number) "Next Channel" (to select the next channel) "Previous Channel" (to select the previous channel) "List Channel" (to hear a list of available channels) "Channel Name" (to change the channel by its spoken name) "Select Name" (to say the name of a channel) "Radio Menu" (to switch to the radio menu) "Main Menu" (to switch to the main menu) "Track" (#) (to change the track) "Next Track" (to play the next track) "Previous Track" (to play the previous track) "Main Menu" (to switch to the main menu) 82 Information Provided by: ELECTRONICS While In: Memo Mode Voice Command Example: To switch to the voice recorder mode, say "Memo." The following are common voice commands for this mode: "New Memo" (to record a new memo) -- During the recording, you may press the Voice Command button to stop recording. You proceed by saying one of the following commands: -- "Save" (to save the memo) -- "Continue" (to continue recording) -- "Delete" (to delete the recording) -- "Play Memos" (to play previously recorded memos) -- During the playback you may press the Voice Command button to stop playing memos. You proceed by saying one of the following commands: -- "Repeat" (to repeat a memo) -- "Next" (to play the next memo) -- "Previous" (to play the previous memo) -- "Delete" (to delete a memo) -- "Delete All" (to delete all memos) Voice Text Reply · If equipped with Uconnect® Voice Command, your Uconnect® 430N, 730N & 731N radios may be able to play incoming Short Message Service (SMS) messages (text messages) through the vehicle's sound system. · It also allows you to respond by selecting from various pre - defined phrases. · Not all phones are compatible with this feature. Refer to the phone compatibility list at www.UconnectPhone.com. Connected mobile phones must be bluetoothcompatible and paired with your radio. · Press the "Voice Command" button started. and after the BEEP, say "SMS" to get NOTE: To access the tutorial, press the "Voice Command" button . After the BEEP, say "tutorial." Press any hard-key/button or touch the display (Touch-Screen radio) to cancel the tutorial. WARNING! Any voice commanded system should be used only in safe driving conditions following applicable laws regarding phone use. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing you and others to be severely injured or killed. Information Provided by: 83 ELECTRONICS Bluetooth® STREAMING AUDIO · If equipped with Uconnect® Voice Command, your Bluetooth-equipped iPod® devices, cell phones or other media players, may also be able to stream music to your vehicles speakers. Your connected device must be Bluetoothcompatible, and paired with your radio (see www.UconnectPhone.com for pairing instructions). · Non-Touch-Screen Radios: Press the "AUX" button on the radio faceplate until "BT" or "Audio Streaming" is displayed on the radio screen. · Touch-Screen-Radios: Press the "RADIO/MEDIA" or "MEDIA" hard-key and then touch the "AUX" soft-key tab. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) · The EVIC features a driver interactive display that is located in the instrument cluster. Pressing the controls on the steering wheel allows the driver to select vehicle information and Personal Settings. For additional information, refer to Programmable Features in this guide. · Press and release the MENU button to scroll through the main menus (Fuel Economy, Warnings, Timer, Units, System, Personal Settings) or to exit sub menus. · Press and release the SELECT button for access to main menus, sub menus or to select a personal setting in the setup menu. · Press and release the COMPASS button to display one of eight compass readings and the outside temperature or to exit sub menus. · Press and release the DOWN button to scroll downward through the sub menus. 84 Information Provided by: ELECTRONICS EVIC Main Menu · To step to each main menu feature press and release the MENU button once for each step. A step from the last item in the list will cause the first item in the feature list to be displayed. The following features are in the Main menu: · Compass, Outside Temperature, and ECO display · Digital Speedometer · Average Fuel Economy · Distance to Empty · Elapsed Time · Vehicle Information · Coolant Temp · Oil Pressure · Transmission Temp · Oil Life Remaining (Automatic Oil Change Indicator) · EVIC Units Selection · System Status · Personal Settings · Tire PSI Compass Calibration · This compass is self-calibrating, which eliminates the need to set the compass manually. When the vehicle is new, the compass may appear erratic and the EVIC will display "CAL" until the compass is calibrated. · You may also calibrate the compass by completing one or more 360 degree turns (in an area free from large metal or metallic objects) until the "CAL" message displayed in the EVIC turns off. The compass will now function normally. ECO · The ECO message will appear in your EVIC display whenever you are driving in a fuel efficient manner. · This feature allows you to monitor when you are driving in a fuel efficient manner, and it can be used to modify driving habits in order to increase fuel economy. Information Provided by: 85 ELECTRONICS PROGRAMMABLE FEATURES Electronic Vehicle Information Center (EVIC) · The EVIC can be used to program the following Personal Settings. Press and release the MENU button until Personal Settings displays, then press the DOWN button to scroll through the settings. Press the SELECT button to change the setting. · Language · Auto UNLK On Exit · RKE Unlock · Sound Horn With RKE Lock · Flash Lamp With Lock · Headlamp Off Delay · Headlamps With Wipers · Key-Off Power Delay · Illumin Approach · Hill Start Assist (HSA) · Display Units of Measure In · Nav Turn by Turn · Display Fuel Saver · Compass Variance · Calibrate Compass Key Fob Programmable Features · The following features may also be programmed by using the Key Fob transmitter or the ignition switch and driver's door lock switch. NOTE: Pressing the LOCK button while you are inside the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Vehicle Security Alarm. Flashing Lamps With Lock · The turn signal lights flashing, when the doors are locked or unlocked, feature can be turned on or off. To turn this feature on or off: · Press and hold the UNLOCK button for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button. · Release both buttons at the same time. 86 Information Provided by: ELECTRONICS POWER INVERTER · A 115 Volt, 150 Watt AC power inverter is located on the front of the center console. · This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. · The power inverter switch is located on the instrument panel below the climate controls. To turn on the power outlet, press the switch once. The indicator light will illuminate. Press the switch a second time to turn the power inverter outlet off. NOTE: The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the power inverter will automatically shut down. Once the electrical device has been removed from the outlet, the inverter should automatically reset. If the power rating exceeds approximately 170 Watts, the power inverter may have to be reset manually. To reset the inverter manually, unplug the device and plug it in again. To avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. WARNING! To Avoid Serious Injury or Death DO NOT: · insert any objects into the receptacles · touch with wet hands Close the lid when not in use. If this outlet is mishandled, it may cause an electric shock and failure. Information Provided by: 87 ELECTRONICS POWER OUTLETS · There are three possible 12Volt Power Outlets in this vehicle. · The front power outlet, located in the lower portion of the instrument panel, is powered when the key is in the ON or ACC position. · A second power outlet is located inside the center console bin and is powered directly from the vehicle battery. · On vehicles equipped with a rear subwoofer, there is a power outlet located in the right rear cargo area. NOTE: · Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced. · Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Improper use of the power outlet can cause damage not covered by your new vehicle warranty. 88 Information Provided by: OFF-ROAD CAPABILITIES (4WD OPERATION) COMMAND-TRAC®/ROCK-TRAC® · The transfer case provides four mode positions: 2H (Two-wheel drive high range), 4H (Four-wheel drive high range), N (Neutral), and 4L (Four-wheel drive low range). · The transfer case is intended to be driven in the 2H position for normal street and highway conditions such as hard-surfaced roads. · Shifting between 2H and 4H · Shifting between 2H and 4H can be made with the vehicle stopped or in motion. Shift the transfer case lever firmly to 4H at any speed up to 50 mph (80 km/h). · Shifting between 4H and 4L (Automatic Transmission) · Shifting between 4H and 4L should be made with the vehicle rolling at 2 to 3 mph (3 to 5 km/h). Shift the automatic transmission into NEUTRAL then shift the transfer case lever firmly to 4L (do not pause with the transfer case in NEUTRAL). Once the shift is completed, place the automatic transmission into DRIVE. · Shifting between 4H and 4L (Manual Transmission) · Shifting between 4H and 4L should be made with the vehicle rolling at 2 to 3 mph (3 to 5 km/h). Fully depress the clutch pedal and shift the transfer case lever firmly to 4L (do not pause with the transfer case in NEUTRAL). Once the shift is completed, release the clutch pedal. NOTE: To enhance off-road performance in 4L mode, manual transmission vehicles will start regardless of whether or not the clutch pedal is depressed. AXLE LOCK (TRU-LOK®) RUBICON ONLY · The AXLE LOCK switch is located on the instrument panel (to the left of the steering column). · This feature will only activate when the following conditions are met: · Key in Run Position, vehicle in 4L (Low) range. · Vehicle speed at 10 mph (16 km/h) or less. · Press the bottom of the AXLE LOCK switch once to lock the rear axle only and a second time to lock the front axle (the rear and front axle lock indicator lights will illuminate). · To unlock the axles, press the top of the AXLE LOCK switch. · The indicator light will flash until the axles are fully locked or unlocked. Information Provided by: 89 OFF-ROAD CAPABILITIES (4WD OPERATION) ELECTRONIC SWAY BAR DISCONNECT RUBICON ONLY Off-Road · This feature will only activate when the following conditions are met: · Key in Run positon, vehicle in 4L (Low) or 4H (High) range. · Vehicle speed under 18 mph. · Press the SWAY BAR switch, located on the instrument panel (to the left of the steering column), once to disconnect the Sway Bar. · The Sway Bar indicator light will illuminate in the instrument cluster. On-Road · Press the SWAY BAR switch a second time to reconnect the Sway Bar. · The Sway Bar should remain in on-road mode during normal driving conditions. 90 Information Provided by: TRAILER TOWING WEIGHTS (MAXIMUM TRAILER WEIGHT RATINGS) Information Provided by: Engine/ Transmission 3.6L/Manual 3.6L/Manual 3.6L/Automatic 3.6L/Automatic 3.6L/Manual 3.6L/Manual 3.6L/Automatic 3.6L/Automatic 3.6L/Manual 3.6L/Automatic 3.6L/Automatic 3.6L/Manual Axle 3.21 3.73 3.21 3.73 3.21 3.73 3.21 3.73 4.10 3.73 4.10 3.21 Model GCWR (Gross Combined Wt. Rating) TwoDoor Sport Model (4WD) TwoDoor Sport Model (4WD) TwoDoor Sport Model (4WD) TwoDoor Sport Model (4WD) TwoDoor Sahara Model (4WD) TwoDoor Sahara Model (4WD) TwoDoor Sahara Model (4WD) TwoDoor Sahara Model (4WD) 2Door Rubicon Model (4WD) TwoDoor Rubicon Model (4WD) TwoDoor Rubicon Model (4WD) FourDoor Sport Model (4WD) 6,296 lbs (2 856 kg) 6,296 lbs (2 856 kg) 6,309 lbs (2 862 kg) 6,309 lbs (2 862 kg) 6,355 lbs (2 883 kg) 6,355 lbs (2 883 kg) 6,368 lbs (2 888 kg) 6,368 lbs (2 888 kg) 6,445 lbs (2 923 kg) 6,458 lbs (2 929 kg) 6,458 lbs (2 929 kg) 6,552 lbs (2 972 kg) Frontal Area 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 25 sq ft (2.32 sq m) 32 sq ft (2.97 sq m) Max. GTW (Gross Trailer Wt.) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) 2,000 lbs (907 kg) Max. Trailer Tongue Wt. (See Note) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) 200 lbs (91 kg) UTILITY 91 UTILITY 92 Engine/ Transmission Axle Model GCWR (Gross Combined Wt. Rating) Frontal Area Max. GTW (Gross Trailer Wt.) Max. Trailer Tongue Wt. (See Note) 3.6L/Manual 3.73 FourDoor Sport Model (4WD) 8,052 lbs (3 652 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6L/Automatic 3.21 FourDoor Sport Model (4WD) 6,566 lbs (2 978 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6L/Automatic 3.73 FourDoor Sport Model (4WD) 8,066 lbs (3 659 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6L/Manual 3.21 FourDoor Sahara Model (4WD) 6,768 lbs (3 070 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) 3.6L/Manual 3.73 FourDoor Sahara Model (4WD) 8,268 lbs (3 750 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6L/Automatic 3.21 FourDoor Sahara Model (4WD) 6,782 lbs (3 076 kg) 32 sq ft (2.97 sq m) 2,000 lbs (907 kg) 200 lbs (91 kg) Information Provided by: 3.6L/Automatic 3.73 FourDoor Sahara Model (4WD) 8,282 lbs (3 757 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6L/Manual 4.10 FourDoor Rubicon Model (4WD) 8,334 lbs (3 780 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) 3.6L/Automatic 4.10 FourDoor Rubicon Model (4WD) 8,347 lbs (3 786 kg) 32 sq ft (2.97 sq m) 3,500 lbs (1 587 kg) 350 lbs (159 kg) Refer to local laws for maximum trailer towing speeds. NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and cargo (ie. the GVWR), and the GVWR should never exceed the weight referenced on the Tire and Loading Information placard. RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Flat Tow Dolly Tow On Trailer Wheels OFF the Ground NONE Front Rear ALL Four-Wheel Drive Models · See Instructions · Manual transmission in gear (NOT in NEUTRAL (N) · Transfer case in NEUTRAL (N) · Tow in forward direction NOT ALLOWED NOT ALLOWED OK Information Provided by: UTILITY 93 UTILITY Recreational Towing Four-Wheel Drive Models NOTE: The transfer case must be shifted into NEUTRAL (N), automatic transmission must be shifted into PARK, and manual transmission must be placed in gear (NOT in NEUTRAL) for recreational towing. Shifting Into NEUTRAL (N) Use the following procedure to prepare your vehicle for recreational towing. 1. Bring the vehicle to a complete stop. 2. Press and hold the brake pedal. 3. Shift the automatic transmission into NEUTRAL or depress the clutch pedal on a manual transmission. 4. Turn OFF the engine. 5. Shift the transfer case lever into NEUTRAL (N). 6. Start the engine. 7. Shift the transmission into REVERSE. 8. Release the brake pedal (and clutch pedal on manual transmissions) for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with automatic transmission in DRIVE or manual transmis- sion in first gear. 10. Turn OFF the engine. 11. Firmly apply the parking brake. 12. Shift the transmission into PARK or place manual transmission in gear (NOT in Neutral). 13. Attach the vehicle to the tow vehicle using a suitable tow bar. 14. Release the parking brake. Shifting Out of NEUTRAL (N) Use the following procedure to prepare your vehicle for normal usage. 1. Bring the vehicle to a complete stop, leaving it connected to the tow vehicle. 2. Firmly apply the parking brake. 3. Turn the ignition switch to the LOCK/OFF position. 4. Turn the ignition switch to the ON/RUN position, but do not start the engine. 5. Press and hold the brake pedal. 6. Shift the transmission into NEUTRAL. 7. Shift the transfer case lever to the desired position. 94 Information Provided by: UTILITY NOTE: When shifting out of transfer case NEUTRAL (N), turning the engine OFF may be required to avoid gear clash. 8. Shift the automatic transmission into PARK, or place manual transmission in Neutral. 9. Release the brake pedal. 10. Disconnect vehicle from the tow vehicle. 11. Start the engine. 12. Press and hold the brake pedal. 13. Release the parking brake. 14. Shift the transmission into gear, release the brake pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally. CAUTION! · It is necessary to follow these steps to be certain that the transfer case is fully in NEUTRAL (N) before recreational towing to prevent damage to internal parts. · Damage to the transmission may occur if the transmission is shifted into PARK with the transfer case in NEUTRAL (N) and the engine running. With the transfer case in NEUTRAL (N) ensure that the engine is OFF prior to shifting the transmission into PARK. · Front or rear wheel lifts should not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing. · Tow only in the forward direction. Towing this vehicle backwards can cause severe damage to the transfer case. · Automatic transmissions must be placed in the PARK position for recreational towing. · Manual transmissions must be placed in gear (not in Neutral) for recreational towing. · Before recreational towing, perform the procedure outlined under "Shifting Into NEUTRAL (N)" to be certain that the transfer case is fully in NEUTRAL (N). Otherwise, internal damage will result. · Towing this vehicle in violation of the above requirements can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. · Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the NEUTRAL (N) position without first fully engaging the parking brake. The transfer case NEUTRAL (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move, even if the transmission is in PARK. The parking brake should always be applied when the driver is not in the vehicle. Information Provided by: 95 WHAT TO DO IN EMERGENCIES ROADSIDE ASSISTANCE · Dial toll-free 1-800-521-2779 for U.S. Residents or 1-800-363-4869 for Canadian Residents. · Provide your name, vehicle identification number, license plate number, and your location, including the telephone number from which you are calling. · Briefly describe the nature of the problem and answer a few simple questions. · You will be given the name of the service provider and an estimated time of arrival. If you feel you are in an "unsafe situation", please let us know. With your consent, we will contact local police or safety authorities. INSTRUMENT CLUSTER WARNING LIGHTS - Electronic Stability Control (ESC) Activation/Malfunction Indicator Light · If the "ESC Activation/Malfunction Indicator Light" comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), we recommend you drive to the nearest service center and have the vehicle serviced immediately. · The "ESC Activation/Malfunction Indicator Light" starts to flash as soon as the tires lose traction and the ESC system becomes active. If the light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. The light also flashes when TCS is active. To improve the vehicle's traction when starting off in deep snow, sand or gravel, it may be desirable to switch the ESC system to Partial Off mode by momentarily pressing the ESC Off switch. - Tire Pressure Monitoring System (TPMS) Light · Each tire, including the spare (if provided), should be checked monthly, when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) · As an added safety feature, your vehicle has been equipped with a Tire Pressure Monitoring System (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. 96 Information Provided by: WHAT TO DO IN EMERGENCIES · IF THE LIGHT STARTS FLASHING INDICATING A LOW TIRE PRESSURE, ADJUST THE AIR PRESSURE IN THE LOW TIRE TO THE AIR PRESSURE SHOWN ON THE VEHICLE PLACARD OR TIRE INFLATION PRESSURE LABEL LOCATED ON THE DRIVER'S DOOR. NOTE: AFTER INFLATION, THE VEHICLE MAY NEED TO BE DRIVEN FOR 20 MINUTES BEFORE THE FLASHING LIGHT WILL TURN OFF. · Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. · Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue each time the vehicle is restarted as long as the malfunction exists. · When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle, to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. NOTE: Tire pressures change by approximately 1 psi (7 kPa) per 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter. Example: If garage temperature is 68°F (20°C) and the outside temperature is 32°F (0°C), then the cold tire inflation pressure should be increased by 3 psi (21 kPa), which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Do not use tire sealant from a can, or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result. Information Provided by: 97 WHAT TO DO IN EMERGENCIES - Engine Temperature Warning Light · This light warns of an overheated engine condition. · If the light turns on and a warning chime sounds while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately. · We recommend that you do not operate the vehicle or engine damage will occur. Have the vehicle serviced immediately. WARNING! A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. BRAKE - Brake Warning Light · The Brake Warning light illuminates when there is either a system malfunction or the parking brake is applied. If the light is on and the parking brake is not applied, it indicates a possible brake hydraulic malfunction, brake booster problem or an Anti-Lock Brake System problem. · Please have your vehicle serviced immediately. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. - Malfunction Indicator Light (MIL) · Certain conditions, such as a loose or missing gas cap, poor fuel quality, etc., may illuminate the MIL after engine start. The vehicle should be serviced if the light stays on through several typical driving cycles. In most situations, the vehicle will drive normally and not require towing. · If the MIL flashes when the engine is running, serious conditions may exist that could lead to immediate loss of power or severe catalytic converter damage. We recommend you do not operate the vehicle. Have the vehicle serviced immediately. Electronic Stability Control (ESC) OFF Activation/Malfunction Warning Light · If the ESC OFF warning light comes on continuously with the engine running, a malfunction has been detected. · If this light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), we recommend you drive to the nearest service center and have the vehicle serviced immediately. 98 Information Provided by: WHAT TO DO IN EMERGENCIES - Charging System Light · This light shows the status of the electrical charging system. If the charging system light remains on, it means that the vehicle is experiencing a problem with the charging system. · We recommend you do not continue driving if the charging system light is on. Have the vehicle serviced immediately. - Oil Pressure Warning Light · This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. · We recommend you do not operate the vehicle or engine damage will occur. Have the vehicle serviced immediately. - Anti-Lock Brake (ABS) Light · This light monitors the Anti-Lock Brake System (ABS). · If the light is not on during starting, stays on, or turns on while driving, we recommend you drive to the nearest authorized dealer immediately and have the vehicle serviced immediately. - Electronic Throttle Control (ETC) Indicator Light · This light informs you of a problem with the system. · If a problem is detected, the light will come on while the engine is running. Cycle the ignition when the vehicle has completely stopped and the shift lever is placed in the PARK position; the light should turn off. · If the light remains lit with the engine running, your vehicle will usually be drivable; however, see an authorized dealer immediately. If the light is flashing when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle or engine stall and your vehicle may require towing. - Air Bag Warning Light · If the light is not on during starting, stays on, or turns on while driving, have the vehicle serviced by an authorized service center immediately. Fuel Cap/Loose Gas Cap Message · If a "gas cap" message (shown as gASCAP) appears, tighten the gas cap until a "clicking" sound is heard. · Press the odometer reset button to turn the message off. · If the message continues to appear for more than three days after tightening the gas cap, see your authorized service center. Information Provided by: 99 WHAT TO DO IN EMERGENCIES OIL CHANGE EVIC INDICATOR Message · If an "oil change" message (shown as "Change Oil Soon" and "Oil Change Needed") appears and a single chime sounds, it is time for your next required oil change. Resetting The Light After Servicing · Turn the ignition switch to the ON/RUN position (do not start engine). · Fully depress the accelerator pedal three times within 10 seconds. · Turn the ignition switch to the OFF/LOCK position. HOTOIL Transmission Temperature Warning Message · The HOTOIL cluster message will appear in the odometer accompanied with a chime to indicate that there is excessive transmission fluid temperature that might occur with severe usage such as trailer towing. · It may also occur when operating the vehicle in a high torque converter slip condition, such as 4-wheel-drive operation (e.g., snow plowing, off-road operation). · If this HOTOIL message turns on, stop the vehicle and run the engine at idle or faster, with the transmission in NEUTRAL until the message turns off. CAUTION! Continuous driving with the Transmission Temperature HOTOIL Warning message illuminated will eventually cause severe transmission damage and transmission failure. WARNING! Continued operation with the Transmission Temperature HOTOIL Warning message illuminated could cause the fluid to boil over, come into contact with the hot engine or exhaust components causing a fire that may result in personal injury. 100 Information Provided by: WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS · In any of the following situations, you can reduce the potential for overheating by taking the appropriate action. · On the highways -- slow down. · In city traffic -- while stopped, shift the transmission to NEUTRAL, but do not increase engine idle speed. NOTE: There are steps that you can take to slow down an impending overheat condition: · If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat. · You can also turn the temperature control to maximum heat, the mode control to floor and the blower control to high. This allows the heater core to act as a supplement to the radiator and aids in removing heat from the engine cooling system. CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately, and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator or coolant bottle is hot. Information Provided by: 101 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location · The jack and lug wrench are located in the rear storage compartment. NOTE: Turn the black plastic wing nut counter clockwise to loosen the jack from the storage bin. Spare Tire Stowage · To remove the spare tire from the carrier, remove the tire cover, if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise. NOTE: If you have added aftermarket accessories to the spare tire mounted carrier, it cannot exceed a gross weight of 69 lbs (31.3 kg) including the weight of the spare tire. 102 Information Provided by: WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park on a firm, level surface. Avoid ice or slippery areas. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake. 4. Shift the automatic transmission into PARK, or a manual transmission into REVERSE. 5. Turn the ignition to LOCK. Block both the front and rear of the wheel diagonally opposite of the jacking position. For example, if changing the right front tire, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Jacking Instructions 1. Remove the spare tire, jack and tools from the stored location. 2. Loosen (but do not remove) the wheel lug nuts by turning them to the left one turn while the wheel is still on the ground. 3. Assemble the jack and jacking tools. Connect the jack handle driver to the extension, then to the lug wrench. Information Provided by: 103 WHAT TO DO IN EMERGENCIES 4. Operate the jack from the front or the rear of the vehicle. Place the jack under the axle tube, as shown. Do not raise the vehicle until you are sure the jack is fully engaged. 5. Raise the vehicle by turning the jack screw to the right. Raise the vehicle only until the tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. 6. Remove the lug nuts and wheel. 7. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the lug nuts clockwise. 8. Lower the vehicle by turning the jack screw to the left, and remove the jack. 9. Finish tightening the lug nuts. Push down on the wrench while tightening for increased leverage. Alternate nuts until each nut has been tightened twice. The correct wheel nut tightness is 95 ft lbs (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or at a service station. 10. Remove the jack assembly and wheel blocks. 11. Secure the tire, jack, and tools in their proper locations. 12. Remove blocks from wheels. 104 Information Provided by: WHAT TO DO IN EMERGENCIES Road Tire Installation 1. Mount the road tire on the axle. 2. Install the remaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. 3. Lower the vehicle to the ground by turning the jack handle counterclockwise. 4. Finish tightening the lug nuts. Push down on the wrench while at the end of the handle for increased leverage. Tighten the lug nuts in a star pattern until each nut has been tightened twice. The correct tightness of each lug nut is 95 ft/lbs (130 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your authorized dealer or service station. 5. After 25 miles (40 km) check the lug nut torque with a torque wrench to ensure that all lug nuts are properly seated against the wheel. CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. Information Provided by: 105 WHAT TO DO IN EMERGENCIES WARNING! · Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. · Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. · Never start or run the engine while the vehicle is on a jack. · The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. · Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: · Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle. · Turn on the Hazard Warning flasher. · Block the wheel diagonally opposite the wheel to be raised. · Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. · Do not let anyone sit in the vehicle when it is on a jack. · Do not get under the vehicle when it is on a jack. · Only use the jack in the positions indicated and for lifting this vehicle during a tire change. · If working on or near a roadway, be extremely careful of motor traffic. · To assure that spare tires, flat or inflated, are securely stowed, spares must be stowed with the valve stem facing the ground. · Raising the vehicle higher than necessary can make the vehicle less stable and cause a collision. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. · To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. · A loose tire or jack, thrown forward in a collision or hard stop, could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. · To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is lowered to the ground. 106 Information Provided by: WHAT TO DO IN EMERGENCIES JUMP-STARTING · If your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. · Jump-starting can be dangerous if done improperly so please follow the procedures in this section carefully. NOTE: When using a portable battery booster pack follow the manufacturer's operating instructions and precautions. Preparations for Jump-Start · The battery in your vehicle is located in the right rear of the engine compartment. · Set the parking brake, shift the automatic transmission into PARK and turn the ignition to LOCK. · Turn off the heater, radio, and all unnecessary electrical accessories. · If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Jump-Starting Procedure · Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. · Connect the opposite end of the positive (+) jumper cable to the positive (+) post of the booster battery. · Connect the negative end (-) of the jumper cable to the negative (-) post of the booster battery. · Connect the opposite end of the negative (-) jumper cable to a good engine ground (exposed metal part of the discharged vehicle's engine) away from the battery and the fuel injection system. · Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. Information Provided by: 107 WHAT TO DO IN EMERGENCIES Once the engine is started, remove the jumper cables in the reverse sequence: · Disconnect the negative (-) jumper cable from the engine ground of the vehicle with the discharged battery. · Disconnect the negative end (-) of the jumper cable from the negative (-) post of the booster battery. · Disconnect the opposite end of the positive (+) jumper cable from the positive (+) post of the booster battery. · Disconnect the positive (+) end of the jumper cable from the positive (+) post of the discharged vehicle. · If frequent jump-starting is required to start your vehicle you should have the battery and charging system inspected at your authorized dealer. CAUTION! · Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. · Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. · Accessories that can be plugged into the vehicle power outlets draw power from the vehicle's battery, even when not in use (i.e., cellular phones, etc.). Eventually, if plugged in long enough, the vehicle's battery discharges sufficiently to degrade battery life and/or prevent the engine from starting. WARNING! · When temperatures are below the freezing point, electrolyte in a discharged battery may freeze. Do not attempt jump-starting because the battery could rupture or explode and cause personal injury. Battery temperature must be brought above the freezing point before attempting a jump-start. · Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. · Remove any metal jewelry, such as watch bands or bracelets, that might make an inadvertent electrical contact. You could be severely injured. · Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery. · Do not allow vehicles to touch each other as this could establish a ground connection and personal injury could result. · Failure to follow this procedure could result in personal injury or property damage due to battery explosion. · Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 108 Information Provided by: WHAT TO DO IN EMERGENCIES EMERGENCY TOW HOOKS · If your vehicle is equipped with tow hooks, they are mounted in the front and the rear. NOTE: For off-road recovery, it is recommended to use both of the front tow hooks to minimize the risk of damage to the vehicle. CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off-road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. Tow straps are recommended when towing the vehicle; chains may cause vehicle damage. WARNING! · Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. · Stand clear of vehicles when pulling with tow hooks. Tow straps may become disengaged, causing serious injury. SHIFT LEVER OVERRIDE · If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use the following procedure to temporarily move the shift lever: · To access the shift lever override, remove the override cover located on the shift lever bezel, next to the shift lever. · Firmly set the parking brake. · Turn the ignition switch to the ACC or ON position without starting the engine. · Press and maintain firm pressure on the brake pedal. · Using a screwdriver or similar tool, press and hold the override tab through the access port on the center console. · Move the shift lever into the NEUTRAL position. · The vehicle may then be started in NEUTRAL. · Reinstall the override cover. Information Provided by: 109 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE · The manufacturer requires towing your vehicle with all four wheels OFF the ground using a flatbed. CAUTION! Towing this vehicle using any other method could result in extensive damage to the transfer case and/or transmission. FREEING A STUCK VEHICLE · If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion. Turn your steering wheel right and left to clear the area around the front wheels. Then shift back and forth between DRIVE/1st gear and REVERSE. Using minimal accelerator pedal pressure to maintain the rocking motion, without spinning the wheels, is most effective. NOTE: If your vehicle is equipped with Traction Control or Electronic Stability Control (ESC), turn the system OFF before attempting to "rock" the vehicle. CAUTION! · Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the shift lever in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle. · When "rocking" a stuck vehicle by moving between DRIVE/1st gear and REVERSE, do not spin the wheels faster than 15 mph (24 km/h), or drivetrain damage may result. · Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. It can also damage the tires. Do not spin the wheels above 30 mph (48 km/h) while in gear (no transmission shifting occurring). WARNING! Fast spinning tires can be dangerous. Forces generated by excessive wheel speeds may cause damage, or even failure, of the axle and tires. A tire could explode and injure someone. Do not spin your vehicle's wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. 110 Information Provided by: WHAT TO DO IN EMERGENCIES EVENT DATA RECORDER (EDR) · This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that assists in understanding how a vehicle's systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as: · How various systems in your vehicle were operating. · Whether or not the driver and passenger safety belts were buckled/fastened. · How far (if at all) the driver was depressing the accelerator and/or brake pedal. · How fast the vehicle was traveling. · These data can help provide a better understanding of the circumstances in which crashes and injuries occur. NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situation occurs; no data are recorded by the EDR under normal driving conditions and no personal data (e.g. name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. · To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR. Information Provided by: 111 MAINTAINING YOUR VEHICLE OPENING THE HOOD · Release the two hood latches located on the left and right side of the hood. · Raise the hood and locate the safety latch, in the middle of the hood opening. · Push the latch to the left side of the vehicle, to open the hood. You may have to push down slightly on the hood before pushing the safety latch. · Insert the support rod into the slot on the hood. · To close the hood, remove the support rod and place it in the retaining clip, then lower the hood slowly. · Secure both of the hood latches. WARNING! Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision. Failure to follow this warning could result in serious injury or death. 112 Information Provided by: MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 3.6L Engine Information Provided by: 113 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Component Engine Coolant 3.6L Engine Engine Oil with filter3.6L Engine Engine Oil Filter 3.6L Engine Spark Plug 3.6L Engine Automatic Transmission Manual Transmission Transfer Case Axle differential (front) Axle differential (rear) Brake Master Cylinder Power Steering Reservoir Fuel Selection 2 Door Fuel Selection 4 Door Fluid, Lubricant, or Genuine Part Capacities We recommend you use MOPAR® Antifreeze/ Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). 10.5 Quarts (9.9 Liters) Includes coolant recovery bottle filled to MAX level. We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395 such as MOPAR, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade. 6 quarts (5.7 Liters) We recommend you use MOPAR® brand Engine Oil Filters. -- We recommend you use MOPAR® Spark Plugs (Gap 0.043 in [1.1 mm]). -- We recommend you ONLY use MOPAR® ATF+4® Automatic Transmission Fluid. Failure to use ATF+4® fluid may affect the -- function or performance of your transmission. We recommend you use MOPAR® Manual Transmission Lubricant. -- We recommend you use MOPAR® ATF+4® Automatic Transmission Fluid. -- We recommend you use MOPAR® Gear & Axle Lubricant (SAE 80W-90) (API GL-5). -- 226 RBI (Model 44) - We recommend you use MOPAR® Gear & Axle Lubricant (SAE 80W-90) (API GL-5). For trailer towing,We recommend you use MOPAR® -- Synthetic Gear & Axle Lubricant (SAE 75W-140). Models equipped with Trac-LokTM require an additive. We recommend you use MOPAR® DOT 3 Brake Fluid, SAE J1703. If DOT 3, SAE J1703 brake fluid is not available, -- then DOT 4 is acceptable. We recommend you use MOPAR® Power Steering Fluid +4, MOPAR® or ATF+4® -- Automatic Transmission Fluid. 87 Octane 18.6 Gallons (70 Liters) (Approximate) 87 Octane 22.5 Gallons (85 Liters) (Approximate) 114 Information Provided by: MAINTAINING YOUR VEHICLE CAUTION! · Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is different and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze) or any "globally compatible" coolant (antifreeze). If a non-OAT engine coolant (antifreeze) is introduced into the cooling system in an emergency, the cooling system will need to be drained, flushed, and refilled with fresh OAT coolant (conforming to MS-12106), by an authorized dealer as soon as possible. · Do not use water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. · This vehicle has not been designed for use with propylene glycol-based engine coolant (antifreeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. E85 FLEXIBLE FUEL -- 3.6L ENGINE ONLY Refer to your Owner's Manual on the DVD for further details. CAUTION! Only vehicles with the E-85 fuel filler door label or a yellow gas cap can operate on E-85. MAINTENANCE SCHEDULE Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle. Operating conditions such as frequent short-trips, trailer tow, extremely hot or cold ambient temperatures, and E85 fuel usage will influence when the "Change Oil" or "Oil Change Required" message is displayed. Severe Operating Conditions can cause the change oil message to illuminate as early as 3,500 miles (5,600 km) since last reset. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km). Information Provided by: 115 MAINTAINING YOUR VEHICLE On Electronic Vehicle Information Center (EVIC) equipped vehicles, "Oil Change Required" will be displayed in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles, "Change Oil" will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under "Electronic Vehicle Information Center (EVIC)/Oil Change Required" in "Understanding Your Instrument Panel" or under "Instrument Cluster Description/Odometer/Trip Odometer" in "Understanding Your Instrument Panel" for further information. NOTE: Under no circumstances should oil change intervals exceed 10,000 miles (16,000 km) or twelve months, whichever comes first. Once A Month Or Before A Long Trip: · Check engine oil level · Check windshield washer fluid level · Check the tire inflation pressures and look for unusual wear or damage · Check the fluid levels of the coolant reservoir, brake master cylinder, power steering and automatic transmission, and fill as needed · Check function of all interior and exterior lights Required Maintenance Intervals. Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: · Change oil and filter · Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. · Inspect battery and clean and tighten terminals as required · Inspect automatic transmission fluid if equipped with dipstick · Inspect brake pads, shoes, rotors, drums, hoses and park brake · Inspect engine cooling system protection and hoses · Inspect exhaust system · Inspect engine air cleaner if using in dusty or off-road conditions · Inspect all door latches for presence of grease, reapply if necessary. 116 Information Provided by: 240,000 150,000 224,000 140,000 208,000 130,000 192,000 120,000 176,000 110,000 160,000 100,000 144,000 90,000 128,000 80,000 112,000 70,000 60,000 50,000 40,000 20,000 30,000 MAINTAINING YOUR VEHICLE Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Information Provided by: Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 96,000 80,000 64,000 32,000 48,000 Or Kilometers: Additional Inspections Inspect the CV/Universal joints. X X X X X X Inspect front suspension, tie rod ends, and replace if necessary. X X X X X X Inspect the front and rear axle fluid. X X X Inspect the brake linings, replace as necessary X X X X X X Adjust parking brake on vehicles equipped with four wheel disc brakes. X X X X X X Inspect transfer case fluid. X X Additional Maintenance Replace engine air cleaner filter. X X X X Replace air conditioning/cabin air filter. X X X X X X Replace spark plugs ** X Replace the ignition cables. X Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) X whichever comes first. Change automatic transmission fluid and filter if using your vehicle for any of the following: police, taxi, fleet, or frequent X trailer towing. X X X X X X X X X 117 240,000 150,000 224,000 140,000 208,000 130,000 192,000 120,000 176,000 110,000 160,000 100,000 144,000 90,000 128,000 80,000 112,000 70,000 60,000 50,000 40,000 20,000 30,000 MAINTAINING YOUR VEHICLE 118 Mileage or time passed (whichever comes first) Information Provided by: Or Years: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 96,000 80,000 64,000 32,000 48,000 Or Kilometers: Change the automatic transmission fluid and filter(s). X Change the manual transmission fluid if using your vehicle for any of the following: trailer towing, snow plowing, heavy loading, taxi, police, delivery service (commercial service), X X X X X off-road, desert operation or more than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C). Change transfer case fluid if using your vehicle for any of the following: police, X X taxi, fleet, or frequent trailer towing. Inspect and replace PCV valve if necessary. X Change front and rear axle fluid if using your vehicle for police, taxi, fleet, off-road X X X or frequent trailer towing. ** The spark plug change interval is mileage based only, yearly intervals do not apply. WARNING! · You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. · Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident. 119 Information Provided by: MAINTENANCE RECORD 20,000 Miles (32,000 km) or 2 Years 30,000 Miles (48,000 km) or 3 Years 40,000 Miles (64,000 km) or 4 Years 50,000 Miles (80,000 km) or 5 Years 60,000 Miles (96,000 km) or 6 Years 70,000 Miles (112,000 km) or 7 Years 80,000 Miles (128,000 km) or 8 Years Odometer Date Signature, Authorized Service Center 90,000 Miles (144,000 km) or 9 Years 100,000 Miles (160,000 km) or 10 Years 110,000 Miles (176,000 km) or 11 Years 120,000 Miles (192,000 km) or 12 Years 130,000 Miles (208,000 km) or 13 Years 140,000 Miles (224,000 km) or 14 Years 150,000 Miles (240,000 km) or 15 Years Odometer Date Signature, Authorized Service Center MAINTAINING YOUR VEHICLE MAINTAINING YOUR VEHICLE FUSES Integrated Power Module (fuses) 120 Information Provided by: MAINTAINING YOUR VEHICLE · The Integrated Power Module is located in the engine compartment near the battery. This center contains cartridge fuses, mini-fuses and relays. Cavity J1 J2 J3 J4 J5 J6 J7 J8 J9 J10 J11 J12 J13 J14 J15 J17 J18 J19 J20 J21 J22 M1 M2 M3 M4 M5 M6 M7 M8 M9 Cartridge Fuse Mini Fuse Description -- -- 30 Amp Pink Transfer Case Module -- -- 25 Amp Natural Driver Door Node 25 Amp Natural Passenger Door Node 40 Amp Green Anti-Lock Brake System (ABS) Pump Feed/ESC 30 Amp Pink Anti-Lock Brake System (ABS) Valve Feed/ESC -- -- 40 Amp Green PZEV Sec Motor Feed/Flex Fuel 30 Amp Pink Headlamp Wash Relay/Manifold Tuning Valve 30 Amp Pink Sway Bar 30 Amp Pink Rear Blower Motor/Radiator Fan 60 Amp Yellow Ignition Off Draw (IOD) -- Main 40 Amp Green EBL (Rear Window Defogger) 40 Amp Green Front Blower 40 Amp Green Starter Solenoid 20 Amp Blue Powertrain Control Module (PCM) Trans Range 60 Amp Yellow Radiator Fan 30 Amp Pink Front Wiper LO/HI 20 Amp Blue Front/Rear Washer -- Spare 15 Amp Blue Center High-Mounted Stop Light (CHMSL)/Switch Stop Lamp Feed 20 Amp Yellow Relay Trailer Lighting (Stop) 20 Amp Yellow Frt/Rear Axle Locker Relay -- -- 25 Amp Natural Power Inverter - If Equipped 20 Amp Yellow Power Outlet #1/Rain Sensor 20 Amp Yellow Power Outlet #2 (BATT/ACC SELECT) 20 Amp Yellow Front Heated Seat 20 Amp Yellow Rear Heated Seat (If Equipped) Information Provided by: 121 MAINTAINING YOUR VEHICLE Cavity M10 M11 M12 M13 M14 M15 M16 M17 M18 M19 M20 M21 M22 M23 M24 M25 M26 M27 M28 M29 M30 M31 Cartridge Fuse Mini Fuse Description 15 Amp Blue Ignition Off Draw -- Vehicle Entertainment System (IOD-VES), Satellite Digital Audio Receiver (SDARS), DVD, HandsFree Module (HFM), RADIO, Antenna (ANT), Universal Garage Door Opener (UGDO), Vanity Lamp (VANITY LP) 10 Amp Red (Ignition Off Draw) IOD-HVAC/ATC, MW SENSR, Underhood Lamp (UH LMP) 30 Amp Green Amplifier (AMP) 20 Amp Yellow Ignition Off Draw-- Cabin Compartment Node (IOD-CCN), Wireless Control Module (WCM), SIREN, Multifunction Control Switch (MULTIFCTN SW) 20 Amp Yellow Trailer Tow (Export Only) 20 Amp Yellow COL MOD, IR SNS, Heater Ventilation, Air Conditioning/Automatic Temperature Control (HVAC/ATC), Rear View Mirror (RR VW MIR), Cabin Compartment Node (CCN), Transfer Case Switch (T-CASE SW), RUN/ST, Multi-Function Control Switch (MULTIFTCN SW), Tire Pressure Monitor (TPM), Glow Plug Module (GLW PLG MOD) -- Export Diesel Only 10 Amp Red Occupant Restraint Controller (ORC) 15 Amp Blue Left Tail/License/Park Lamp (LT-TAIL/LIC/PRK LMP) 15 Amp Blue Right Tail/Park/Run Lamp (RT-TAIL/PRK/RUN LMP) 25 Amp Natural Auto Shut Down (ASD #1 and #2) 15 Amp Blue Cabin Compartment Node Interior Light (CCN INT LIGHT), Switch Bank (SW BANK) 20 Amp Yellow Auto Shut Down (ASD #3) 10 Amp Red Right Horn (RT HORN (HI/LOW) 10 Amp Red Left Horn (LT HORN (HI/LOW) 25 Amp Natural Rear Wiper (REAR WIPER) 20 Amp Yellow Fuel Pump (FUEL PUMP), Diesel Lift Pump (DSL LIFT PUMP) -- Export Only 10 Amp Red Power Window Switch/Driver Window Switch 10 Amp Red Ignition Switch Feed, Wireless Module 10 Amp Red PCM Feed/TCM 10 Amp Red Powertrain 15 Amp Blue Wiper Motor Frt, J1962 Diagnostic Feed 20 Amp Yellow Backup Lamps (B/U LAMPS) 122 Information Provided by: MAINTAINING YOUR VEHICLE Cavity M32 M33 M34 M35 M36 M37 M38 Cartridge Fuse Mini Fuse Description 10 Amp Red Occupant Restraint Controller (ORC), TT EUROPE 10 Amp Red Next Generation Controller (NGC), Global Powertrain Engine Controller (GPEC) 10 Amp Red Park Assist (PRK ASST), Heater Ventilation, Air Conditioning Module (HVAC MOD), Headlamp Wash (HDLP WASH), Compass (COMPAS) 10 Amp Red Heated Mirrors 20 Amp Yellow Power Outlet 10 Amp Red Anti-Lock Brake System (ABS) , Electronic Stability Control (ESC), Stop Lamp Switch (STP LP SW), Fuel Pump Rly Hi Control 25 Amp Natural Lock/Unlock Motors (LOCK/UNLOCK MTRS) TIRE PRESSURES · Check the inflation pressure of each tire, including the spare tire, at least monthly and inflate to the recommended pressure for your vehicle. · The tire pressures recommended for your vehicle are found on the "Tire and Loading Information" label located on the driver's side door opening. 2 Door Tire Placard Location Information Provided by: 123 MAINTAINING YOUR VEHICLE 4 Door Tire Placard Location NOTE: Refer to the Owner's Manual on the DVD for more information regarding tire warnings and instructions. WARNING! · Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. · Improperly inflated tires are dangerous and can cause collisions. Underinflation is the leading cause of tire failure and may result in severe cracking, component separation, or "blow out". Over-inflation reduces a tire's ability to cushion shock. Objects on the road and chuck holes can cause damage that results in tire failure. Unequal tire pressures can cause steering problems. You could lose control of your vehicle. Over-inflated or under-inflated tires can affect vehicle handling and can fail suddenly, resulting in loss of vehicle control. 124 Information Provided by: MAINTAINING YOUR VEHICLE WHEEL AND WHEEL TRIM CARE · All wheels and wheel trim, especially aluminum and chrome plated wheels, should be cleaned regularly with a mild soap and water to prevent corrosion. · To remove heavy soil and/or excessive brake dust, use MOPAR® Wheel Cleaner or equivalent or select a non-abrasive, non-acidic cleaner. CAUTION! Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Do not use oven cleaner. These products may damage the wheel's protective finish. Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheel's protective finish. Only MOPAR® Wheel Cleaner or equivalent is recommended. EXTERIOR BULBS Bulb Number 3157 LED (*) PSX24W 3157 168 H13 194 LIGHT BULBS Exterior Backup, Tail, Stop, Turn Lamp Center High-Mounted Stop Lamp (CHMSL) Fog Lamp If Equipped Front Park/Turn Signal Front Side Marker Headlamp Low Beam License Lamp * CHMSL is not serviceable. It is a LED lamp. To replace the LED, the entire CHMSL assembly must be replaced. Information Provided by: 125 CONSUMER ASSISTANCE CHRYSLER GROUP LLC CUSTOMER CENTER P.O. Box 218004 Auburn Hills, MI 483218004 Phone: 18774265337 CHRYSLER CANADA INC. CUSTOMER CENTER P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone: 18004652001 (English) Phone: 18003879983 (French) ASSISTANCE FOR THE HEARING IMPAIRED · To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1800380CHRY. Canadian residents with hearing difficulties that require assistance can use the special needs relay service offered by Bell Canada. For TTY teletypewriter users, dial 711 and for Voice callers, dial 18008550511 to connect with a Bell Relay Service operator. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain, or emit, chemicals known to the State of California to cause cancer and birth defects, or other reproductive harm. PUBLICATIONS ORDERING · If you are the first registered retail owner of your vehicle, you may obtain one free printed copy of the Owner's Manual, Warranty Booklet or Radio Manuals on your DVD by calling 18774265337 (U.S.) or 18003871143 (Canada) or by contacting your dealer. · Replacement User Guide kits or DVDs or, if you prefer, additional printed copies of the Owner's Manual, Warranty Booklet or Radio Manuals may be purchased by visiting www.techauthority.com or by calling 18778904038 (U.S.) or 18003871143 (Canada). Visa, Master Card, American Express and Discover orders are accepted. If you prefer mailing your order, please call the above numbers for an order form. 126 Information Provided by: CONSUMER ASSISTANCE NOTE: · A street address is required when ordering manuals (no P.O. Boxes). · The Owner's Manual and User Guide electronic files are also available on the Chrysler, Jeep, Ram Truck and Dodge websites. · Click on the "For Owners" tab, select "Owner/Service Manuals", then select your desired model year and vehicle from the drop down lists. REPORTING SAFETY DEFECTS IN THE UNITED STATES · If you believe that your vehicle has a defect that could cause a collision or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying the manufacturer. · If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer and the manufacturer. · To contact NHTSA, you may either call the Auto Safety Hotline toll free at 18883274236 (TTY: 18004249153), or go to http://www.safercar.gov; or write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE., West Building, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov. In Canada · If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately. Canadian customers who wish to report a safety defect to the Canadian government should contact Transport Canada, Motor Vehicle Defect Investigations and Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/eng/roadsafety/safedrivers-childsafety-index-53.htm · French Canadian customers who wish to report a safety defect to the Canadian government should contact Transport Canada, Motor Vehicle Defect Investigations and Recalls at 1-800-333-0510 or go to http://www.tc.gc.ca/securiteroutiere/ Information Provided by: 127 MOPAR ACCESSORIES AUTHENTIC ACCESSORIES BY MOPAR® · The following highlights just some of the many Authentic Jeep Accessories by Mopar featuring a fit, finish, and functionality specifically for your Jeep Wrangler. · In choosing Authentic Accessories you gain far more than expressive style, premium protection, or extreme entertainment, you also benefit from enhancing your vehicle with accessories that have been thoroughly tested and factory-approved. · For the full line of Authentic Jeep Accessories by Mopar, visit your local Jeep dealership or online at mopar.com for U.S. residents or mopar.ca for Canadian residents. Chrome: · Grille · Mirror Covers · Door Handle Inserts · Tubular Side Steps · Fuel Door · Door Hinge Covers · Tubular Bumpers · Tail Lamp Guards Off Road: · Bumpers · Winches · Performance Axles · Rock Rails · Lift Kits · Skid Plates · Lights Exterior: · Black Tubular Side Steps · Front End Covers · Hard Top Storage Dolly · Spare Tire Covers · Wheel Locks · Hood · Cab Covers · Soft Tops · Fuel Cap · Air Deflectors · Wheels · Splash Guards · Fender Flares Interior: · Premium Carpet Floor Mats · Hard Top Headliner · Unique Katzkin Leather Interiors · Slush Floor Mats · Seat Covers · Instrument Panel Appliques · Lockable Storage · Cargo Area Tray Electronics: · Mopar® Web (WiFi) · Remote Start · Ambient Footwell Lighting · Electronic Vehicle · Kicker Sound System Tracking System Carriers: · Freedom Top Carriers · Spare Tire-mount Ski · Hitch Receivers and Trailering Accessories 128 Information Provided by: INDEX 4WD . . . . . . . . . . . . . . . . . . .89 Operation . . . . . . . . . . . . . .89 Shifting . . . . . . . . . . . . . . .89 Systems . . . . . . . . . . . . . .89 Airbag . . . . . . . . . . . . . . . . . .13 Air Conditioning . . . . . . . . . . . .28 Alarm (Security Alarm). . . . . . . . .11 Antifreeze (Engine Coolant) . . . . .114 Arming Theft System (Security Alarm) . . . . . . . . . . . . . . . .11 Automatic Headlights . . . . . . . . .23 Automatic Temperature Control (ATC) . . . . . . . . . . . .28 Belts, Seat . . . . . . . . . . . . . . .12 Break-In Recommendations, New Vehicle . . . . . . . . . . . . .23 Bulb Replacement . . . . . . . . . .125 Calibration, Compass . . . . . . . . .85 Capacities, Fluid . . . . . . . . . . .114 Change Oil Indicator . . . . . . . . .100 Changing A Flat Tire . . . . . . . . .102 Child Restraint . . . . . . . . . . . . .14 Climate Control . . . . . . . . . . . . .28 Compass Calibration . . . . . . . . . .85 Cooling System Coolant Capacity . . . . . . . . .114 Selection of Coolant (Antifreeze) . . . . . . . . . . . .114 Cruise Control (Speed Control) . . . .26 Customer Assistance . . . . . . . . .126 Defects, Reporting . . . . . . . . . .127 Dimmer Control. . . . . . . . . . . . .24 Dimmer Switch, Headlight . . . . . .24 Disarming, Theft System . . . . . . .12 ECO . . . . . . . . . . . . . . . . . . .85 Electronic Speed Control (Cruise Control) . . . . . . . . . . .26 Electronic Stability Control (ESC) . .96 Electronic Vehicle Information Center (EVIC) . . . . . . . . . .84, 86 Emergency, In Case of Brake Warning Light . . . . . . .98 Jacking . . . . . . . . . . . . . .102 Overheating . . . . . . . . . . . .101 Engine Break-In Recommendations . . .23 Compartment . . . . . . . . . . .113 Fuel Requirements . . . . . . .114 Oil . . . . . . . . . . . . . . . . .114 Oil Selection . . . . . . . . . . .114 Overheating . . . . . . . . . . . .101 Event Data Recorder . . . . . . . . .111 Exterior Lights. . . . . . . . . . . . .125 Flash-To-Pass . . . . . . . . . . . . . .24 Fluid Capacities. . . . . . . . . . . .114 Fluids, Lubricants and Genuine Parts . . . . . . . . . . . . . . . .114 Fog Lights . . . . . . . . . . . . .23, 24 Folding Rear Seat . . . . . . . . . . .20 Four Wheel Drive Operation . . . . . .89 Freeing A Stuck Vehicle . . . . . . .110 Front Heated Seats. . . . . . . . . . .22 Fuel Filler Cap (Gas Cap) . . . . . . . .99 Requirements . . . . . . . . . .114 Tank Capacity . . . . . . . . . .114 Fuse . . . . . . . . . . . . . . . . . .120 Fuses. . . . . . . . . . . . . . . . . .120 Headlights Automatic . . . . . . . . . . . . .23 Dimmer Switch . . . . . . . . . .24 High Beam . . . . . . . . . . . . .24 Heated Seats . . . . . . . . . . . . . .22 High Beam/Low Beam Select (Dimmer) Switch . . . . . . . . . .24 Hood Release . . . . . . . . . . . . .112 Instrument Cluster . . . . . . . . . . . .8 Indicators . . . . . . . . . . . . . .9 Instrument Cluster Warning Lights . . . . . . . . . . . . . . .8, 96 Integrated Power Module (Fuses) . .120 Interior and Instrument Lights . . . . .7 Intermittent Wipers (Delay Wipers) . .25 Inverter Outlet (115V) . . . . . . . . .87 Inverter, Power . . . . . . . . . . . . .87 iPod®/USB/MP3 Control . . . . . . . .77 Bluetooth Streaming Audio . . . .84 Information Provided by: 129 INDEX Jacking Instructions . . . . . . . . .103 Jack Location . . . . . . . . . . . . .102 Jack Operation . . . . . . . . .102, 103 Jump Starting . . . . . . . . . . . . .107 Key Fob . . . . . . . . . . . . . . . . .10 Key Fob Programmable Features . . .86 Lane Change and Turn Signals . . . .24 Lane Change Assist . . . . . . . . . .24 Lap/Shoulder Belts . . . . . . . . . . .12 LATCH (Lower Anchors and Tether for CHildren) . . . . .14, 15, 16, 17, 18 Lights Engine Temperature Warning . . .98 Tire Pressure Monitoring (TPMS) . . . . . . . . . . . . . . .96 Turn Signal . . . . . . . . . . . . .24 Warning (Instrument Cluster Description) . . . . . . . . . . . . .8 Lower Anchors and Tether for CHildren (LATCH) . . . . . . . . . . . . . . .15 Maintenance Record . . . . . . . . .119 Maintenance Schedule . . . . . . . .115 Malfunction Indicator Light (Check Engine) . . . . . . . . . . .98 Navigation Voice Prompt Volume . . . . . . . . . . . . .59, 70 New Vehicle Break-In Period . . . . .23 Oil Change Indicator . . . . . . . . .100 Oil Change Indicator, Reset . . . . .100 Oil, Engine Capacity . . . . . . . . . . . . . .114 Recommendation . . . . . . . .114 Viscosity . . . . . . . . . . . . .114 Outlet Power . . . . . . . . . . . . . . . .88 Overheating, Engine . . . . . . . . .101 Placard, Tire and Loading Information. . . . . . . . . . . . .123 Power Inverter . . . . . . . . . . . . . . .87 Outlet (Auxiliary Electrical Outlet) . . . .88 Preparation for Jacking. . . . . . . .103 Programmable Electronic Features . . . . . . . . . . . . . . .86 Rain Sensitive Wiper System . . . . .25 Rear Seat, Folding . . . . . . . . . . .20 Recreational Towing . . . . . . . . . .93 Shifting into Transfer Case Neutral (N) . . . . . . . . . . . . .94 Shifting out of Transfer Case Neutral (N) . . . . . . . . . . . . .94 Remote Starting System . . . . . . . .11 Replacement Bulbs. . . . . . . . . .125 Reporting Safety Defects. . . . . . .127 Schedule, Maintenance . . . . . . .115 Seat Belts . . . . . . . . . . . . . . . .12 Seats. . . . . . . . . . . . . . . . . . .19 Adjustment . . . . . . . . . . . . .19 Easy Entry . . . . . . . . . . . . .19 Heated . . . . . . . . . . . . . . .22 Rear Folding . . . . . . . . . . . .20 Security Against Theft . . . . . . . . .11 Shifting Transfer Case, Shifting into Transfer Case Neutral (N) . . . . .94 Transfer Case, Shifting out of Transfer Case Neutral (N) . . . . .94 Shift Lever Override . . . . . . . . .109 Signals, Turn . . . . . . . . . . . . . .24 Spare Tire . . . . . . . . . . . . . . .102 Speed Control (Cruise Control) . . . .26 Starting Remote . . . . . . . . . . . . . . .11 Steering Tilt Column . . . . . . . . . . . . .21 Steering Wheel Audio Controls . . . .77 Stuck, Freeing. . . . . . . . . . . . .110 Supplemental Restraint System Airbag . . . . . . . . . . . . . . . .13 Sway Bar Disconnect, Electronic . . . . . . . . . . . . . .90 Temperature Control, Automatic (ATC) . . . . . . . . . . .28 Theft System Arming. . . . . . . . . .11 Theft System Disarming . . . . . . . .12 Tilt Steering Column . . . . . . . . . .21 130 Information Provided by: INDEX Tires Air Pressure . . . . . . . . . . .123 Changing . . . . . . . . . . . . .102 Jacking . . . . . . . . . . . . . .102 Spare Tire . . . . . . . . . . . . .102 Tow Hooks, Emergency . . . . . . . .109 Towing . . . . . . . . . . . . . . . . . .91 Disabled Vehicle . . . . . . . . .110 Recreational . . . . . . . . . . . .93 Trailer Towing Trailer and Tongue Weight . . . .91 Trailer Weight . . . . . . . . . . . . . .91 Turn Signals. . . . . . . . . . . . . . .24 Uconnect® Voice Command . . . . . .81 Voice Command . . . . . . . . . . . .81 Voice Prompt Volume Navigation . . . . . . . . . . .59, 70 Volume Navigation Voice Prompt . . .59, 70 Warning Lights . . . . . . . . . . . . .96 Washer Rear . . . . . . . . . . . . . . . . .25 Washers, Windshield . . . . . . . . . .25 Wheel and Wheel Trim Care . . . . .125 Windshield Washers . . . . . . . . . .25 Windshield Wipers . . . . . . . . . . .25 Wiper, Rear . . . . . . . . . . . . . . .25 Information Provided by: 131 FAQ (How To?) FREQUENTLY ASKED QUESTIONS GETTING STARTED · How do I install my LATCH Equipped Child Seat? pg. 15 · How do I adjust the height of my Front Seat? pg. 19 OPERATING YOUR VEHICLE · How do I operate my Soft Top? pg. 29 · How do I operate my Hard Top? pg. 38 ELECTRONICS · Which radio is in my vehicle? · Uconnect® 130 pg. 44 · Uconnect® 130 WITH SiriusXMTM pg. 46 · Uconnect® 230 pg. 49 · Uconnect® 430/430N pg. 52 · Uconnect® 730N pg. 62 · How do I activate the Audio Jack? · Uconnect® 130 pg. 51 · Uconnect® 130 WITH SiriusXMTM pg. 51 · Uconnect® 230 pg. 51 · Uconnect® 430/430N pg. 56 · Uconnect® 730N pg. 66 · How do I set the clock on my radio? · Uconnect® 130 pg. 49 · Uconnect® 130 WITH SiriusXMTM pg. 49 · Uconnect® 230 pg. 49 · Uconnect® 430/430N pg. 52 · Uconnect® 730N pg. 62 · How do I use the Navigation feature? · Uconnect® 430/430N pg. 59 · Uconnect® 730N pg. 69 · How do I pair my cell phone via Bluetooth® with the Uconnect® Phone Hands-Free Voice Activation System? pg. 79 · How do I use my iPod®? pg. 77 · How do I use my USB port to listen to audio through my touch-screen radio? pg. 77 132 Information Provided by: FAQ (How To?) OFF-ROAD CAPABILITIES (4WD OPERATION) · How do I shift into different four-wheel drive selections? pg. 89 UTILITY · How do I know how much I can tow with my Jeep Wrangler? pg. 91 WHAT TO DO IN EMERGENCIES · What do I do if my TPMS warning light is blinking? pg. 96 · How do I change a flat tire? pg. 102 · How do I Jump-Start my vehicle? pg. 107 MAINTAINING YOUR VEHICLE · Where is my Fuse Block located? pg. 120 · What type of oil do I use? pg. 114 · How often should I change my engine's oil? pg. 115 · What should my tire pressure be set at? pg. 123 Information Provided by: 133 NOTES 134 Information Provided by: NOTES Information Provided by: 135 NOTES 136 Information Provided by: This guide has been prepared to help you get quickly acquainted with your new Jeep and to provide a convenient reference source for common questions. However, it is not a substitute for your Owner's Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner's Manual, Navigation/Uconnect® Manuals and other Warning Labels in your vehicle. Not all features shown in this guide may apply to your vehicle. For additional information on accessories to help personalize your vehicle, visit www.mopar.com (U.S.), www.mopar.ca (Canada) or your local Jeep dealer. Driving and Alcohol: Drunken driving is one of the most frequent causes of collisions. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don't drive. Ride with a designated non-drinking driver, call a cab, a friend, or use public transportation. WA R N I N G ! Driving after drinking can lead to a collision. Your perceptions are less sharp, your reflexes are slower, and your judgment is impaired when you have been drinking. Never drink and then drive. Information Provided by: Jeep.com Download a free Vehicle Information App by visiting your application store, Keyword (Jeep Vehicle Info), or scanning the Microsoft Tag. To put Microsoft Tags to work U.S. Only Get the free mobile app for your phone for you, use your mobile phhtotpn:/e/'gsebttraogw.msoebri or App store to download a Microsoft Tag reader, like the free one at www.gettag.mobi. Then follow the directions to scan the code. Download a FREE electronic copy of the Owner's Manual or Warranty Booklet by visiting the Owners tab at: www.Jeep.com (U.S.) or www.Jeep.ca (Canada) Information Provided by: 14JK72-926-AA Wrangler First Edition Rev 1 User GuideAdobe PDF Library 10.0.1