Owner's Manual for GARMIN models including: 2-010-12845-00, Speed Sensor, and Cadence Sensor
compatible device. See your owner's manual. • Bring the Garmin compatible device within 3 m of the ANT sensor. • Stay 10 m away from other ANT sensors while pairing. After you pair the first time, your Garmin compatible device automatically recognizes the ANT sensor each time it is activated. User Replaceable Batteries. WARNING
2014 Garmin Ltd. or its subsidiaries. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent ...
Instructions. WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Installing the Speed Sensor. NOTE: If you do not have this sensor, you can skip this task. TIP: Garmin recommends you secure your bike on a stand while installing the sensor. 1
File Info : application/pdf, 8 Pages, 857.77KB
DocumentDocumentSPEED SENSOR AND CADENCE SENSOR INSTRUCTIONS Owner's Manual © 2014 Garmin Ltd. or its subsidiaries All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product. Garmin®, the Garmin logo, and ANT+® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of Garmin. This product is ANT+® certified. Visit www.thisisant.com/directory for a list of compatible products and apps. Table of Contents Speed Sensor and Cadence Sensor Instructions....... 1 Index................................................................................ 3 Table of Contents i Speed Sensor and Cadence Sensor Instructions WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Installing the Speed Sensor NOTE: If you do not have this sensor, you can skip this task. TIP: Garmin® recommends you secure your bike on a stand while installing the sensor. 1 Place and hold the speed sensor on top of the wheel hub. 2 Pull the strap around the wheel hub, and attach it to the hook on the sensor. 5 Take a 15 minute test ride and inspect the sensor and bands to ensure there is no evidence of damage. Pairing the Sensors with Your Device Pairing is the process of connecting an ANT+® wireless sensor, like your speed sensor or cadence sensor, with a Garmin ANT+ compatible device. NOTE: The pairing instructions differ for each Garmin compatible device. See your owner's manual. · Bring the Garmin compatible device within 3 m of the ANT+ sensor. · Stay 10 m away from other ANT+ sensors while pairing. After you pair the first time, your Garmin compatible device automatically recognizes the ANT+ sensor each time it is activated. User Replaceable Batteries WARNING Do not use a sharp object to remove batteries. Keep the battery away from children. Never put batteries in mouth. If swallowed, contact your physician or local poison control center. Replaceable coin cell batteries may contain perchlorate material. Special handling may apply. See www.dtsc.ca.gov /hazardouswaste/perchlorate. The sensor may be tilted when installed on an asymmetrical hub. This does not affect operation. 3 Rotate the wheel to check for clearance. The sensor should not contact other parts of your bike. NOTE: The LED flashes green for five seconds to indicate activity after two revolutions. Installing the Cadence Sensor NOTE: If you do not have this sensor, you can skip this task. TIP: Garmin recommends you secure your bike on a stand while installing the sensor. 1 Select the band size that fits your crank arm securely. The band you select should be the smallest one that stretches across the crank arm. 2 On the non-drive side, place and hold the flat side of the cadence sensor on the inside of the crank arm. 3 Pull the bands around the crank arm, and attach them to the hooks on the sensor. CAUTION Contact your local waste disposal department to properly recycle the batteries. Replacing the Speed Sensor or Cadence Sensor Battery The LED flashes red to indicate a low battery level after two revolutions. 1 Locate the circular battery cover on the back of the sensor. 2 Twist the cover counter-clockwise until the marker points to unlocked and the cover is loose enough to remove. 3 Remove the cover and the battery . TIP: You can use a piece of tape or a magnet to remove the battery from the cover. 4 Rotate the crank arm to check for clearance. The sensor and bands should not contact any part of your bike or shoe. NOTE: The LED flashes green for five seconds to indicate activity after two revolutions. Speed Sensor and Cadence Sensor Instructions 4 Wait 30 seconds. 5 Insert the new battery into the cover, observing polarity. NOTE: Do not damage or lose the O-ring gasket. 6 Twist the cover clockwise until the marker points to locked. NOTE: The LED flashes red and green for a few seconds after battery replacement. When the LED flashes green and 1 then stops flashing, the device is active and ready to send data. Limited Warranty The Garmin standard limited warranty applies to this accessory. For more information, go to www.garmin.com/support/warranty .html. Speed Sensor and Cadence Sensor Specifications Battery type User-replaceable CR2032, 3 V Battery life Approximately 12 months (1 hour per day) Operating temperature range From -20º to 60ºC (from -4º to 140ºF) Wireless frequency/ protocol Water rating 2.4 GHz ANT+ wireless communications protocol 1 ATM1 1 The device withstands pressure equivalent to a depth of 10 m. For more information, go to www.garmin.com/waterrating. 2 Speed Sensor and Cadence Sensor Instructions Index B battery, replacing1 I installing1 P pairing, ANT+ sensors1 S specifications2 speed and cadence sensors1 Index 3 support.garmin.com September 2020 TRA REGISTERED No: ER0128990/14 DEALER No: DA0061884/11 TA-2013/2434 TA-2013/2431 GUID-ED2E448F-AEE6-45A4-ACDF-0BF32AB26783 v5AH XSL Formatter V6.6 MR4 for Windows (x64) : 6.6.6.37929 (2019/03/11 12:35JST) Antenna House PDF Output Library 6.6.1437 (Windows (x64))