YITAHOME Outdoor Storage Shed Assembly Instructions

Important Notice

Retain for future reference. Read carefully.

Assemble on a flat, clean, and soft surface.

Professional installation is highly recommended.

Periodically check that all components are tightly secured.

It is recommended that multiple people assemble this product.

Care and Safety Guidelines

• The shed is intended for storage purposes only and is not designed for habitation.
• Secure the shed to an immovable object or anchor it to the ground using appropriate screws (not included) at the pre-marked locations.
• Do not attempt assembly on windy or cold days.
• Periodically check the shed for stability and ensure the site remains level.
• Handle parts with steel edges carefully.
• Use only the tools listed in the manual for assembly and maintenance.
• Always wear work gloves, safety goggles, and long sleeves during assembly and maintenance.
• Avoid using lawnmowers or mechanical scythes near the shed.
• Always wear safety goggles and follow manufacturer instructions when using power tools.
• Clean the shed with a garden hose or a mild detergent solution. Avoid metal brushes or abrasive cleaners (including degreasers and oil- or acetone-based materials) as they may stain or damage the shed.
• Do not store hot items (e.g., recently used grills, blowtorches) or volatile chemicals in the shed.
• Avoid placing heavy items against the walls to prevent distortion.
• Keep the roof clear of accumulated snow and leaves, as heavy snow can damage the shed and make it unsafe.
• Consider wind direction when locating the shed; minimize exposure, especially on the door side. Keep doors closed and locked when not in use to prevent wind damage.
• Do not stand on the roof.
• Consult local authorities regarding any required permits for erecting the shed.

Installation Precautions

1. Site Preparation: Level the ground.
2. Set up the base: Building a wooden or concrete base is recommended.
3. Leave enough space: Reserve sufficient operating space for external installation work.
4. Tools required: Installation requires two people.
5. Parts placement: Arrange parts after unpacking.
6. Floor protection: Disassemble the packaging cardboard box, unfold it, and lay it on the floor to protect it during assembly.

Parts List

A comprehensive list of parts with item numbers, reference images (described textually), and quantities is provided. Key components include various panels (F.1, F.3, F.6, F.8, F.9, F.10, F.11, F.12, F.13, F.14, F.15, F.17, F.18, F.19), corner pieces (KCFFB.L8, KCFFB.R8, KCFBC, KCFRC, KCRBLC, KCRRH, KCRBC.L, KCRBC.R, KCRRC), window and vent components (VNR4.OUT, VNR4.IN, WIN4.OUT, WIN4.IN, WIN4.PC), various screws and fasteners (FT.1, FT.2, FT.3, FT.4, FT.6, FT.7, FT.7A, FT.8, FT.9, FT.10, FT.11, FT.12, ST5X14, ST3.9X12, ST3.9X30, ST2.9X8, ST4X14, ST6X40, M6, M6X16, M3X6, M8X80), sealing strips (Flat Rubber sealing stripe, Rubber sealing strip), handles (HD.1, HD.2, HD.3, HD.4, HD.5, HD.6, HD.7, HD.8, HD.9, HD.10), and other hardware (W.1, W.2, W.3, W.4, W.6, W.7, W.8, W.9, W.10, W.11, W.12, W.13, W.14, W.15, W.16, R.1, R.2, R.4, R.5, R.6, R.7, R.8), as well as stickers and pads.

Exploded View

An exploded view diagram illustrates the assembly order and placement of all parts. This view shows how the various panels, corner pieces, and hardware connect to form the complete shed structure.

Assembly Steps

1. Step 1: Assemble the main frame using specified panels (kcFRC, F.3, kcFFB.L8, kcFFB.R8, F.1, kcFBC, F.6) and fasteners. Ensure the threshold is inserted correctly into the corner and holes are aligned.
2. Step 2: Attach panels using FT.3 and FT.1 fasteners.
3. Step 3: Continue assembly using F.8, F.9, F.10, and FT.1 fasteners.
4. Step 4: (Diagrammatic step, text description not applicable).
5. Step 5: Attach panels F.12, F.13, F.14, F.15, F.17, F.18, F.11 using specified fasteners.
6. Step 6: Secure panels using FT.1 fasteners.
7. Step 7: (Diagrammatic step, text description not applicable).
8. Step 8: Install guide pieces (W.1) on panels, distinguishing between front and back. Ensure correct orientation (90 degrees) and placement of the strip (inside or outside).
9. Step 9: Insert panels (W.2) into slots, ensuring they are fully seated.
10. Step 10: Secure panels using W.3 and W.4 fasteners, ensuring full insertion into slots.
11. Step 11: Install guide pieces (W.6) on panels, distinguishing between front and back. Ensure correct orientation (90 degrees) and placement of the strip (inside or outside).
12. Step 12: Secure panels using W.4, W.3, and W.2 fasteners, ensuring full insertion into slots.
13. Step 13: Install guide pieces (W.1) on panels, distinguishing between front and back. Ensure correct orientation (90 degrees) and placement of the strip (inside or outside).
14. Step 14: Secure panels using W.4, W.3, and W.2 fasteners, ensuring full insertion into slots.
15. Step 15: Install guide pieces (W.6) on panels, distinguishing between front and back. Ensure correct orientation (90 degrees) and placement of the strip (inside or outside).
16. Step 16: Attach panels (W.7).
17. Step 17: Attach panels (W.8, W.9).
18. Step 18: Attach panels (W.11, W.12).
19. Step 19: Secure panels using FT.1 fasteners.
20. Step 20: Attach panels (W.13, W.16).
21. Step 21: Install window/vent components (VNR4.OUT, VNR4.IN) and attach panels using FT.2 fasteners.
22. Step 22: Attach panels (W.10, W.14).
23. Step 23: Secure components using HD.1 and FT.6 fasteners.
24. Step 24: Attach panels (W.13, W.16, W.14, W.15).
25. Step 25: Attach sealing strips (FR.7, FR.6, FR.3) and panels using FT.7, FT.7A, FT.8 fasteners.
26. Step 26: Secure panels using FT.2 fasteners.
27. Step 27: Attach corner pieces (kcRBLC) and panels (R.1, R.2) using fasteners.
28. Step 28: Attach top panels and bar (R.5) using R.4, R.5, and FT.2 fasteners. Note: Fix top panels and bar with screws before installing on the roof.
29. Step 29: Attach panels (R.7) using FT.3 fasteners.
30. Step 30: Attach top panels and bar (R.5) using R.4, R.5, and FT.2 fasteners. Note: Fix top panels and bar with screws before installing on the roof.
31. Step 31: Attach panels (R.7) using FT.3 fasteners.
32. Step 32: Align top panels with the U-shaped top beam, attach L component to the bar, and lock screws using HD.3, FT.2, FT.3 fasteners.
33. Step 33: Attach components using HD.2 and FT.2 fasteners.
34. Step 34: Attach components using FT.9, HD.5, FT.2, HD.4, FT.10, FT.7A fasteners.
35. Step 35: Repeat steps 28-34 to install remaining panels, using R.4, R.5, FT.2, R.6, FT.9, HD.5, FT.10, HD.4, HD.3, FT.3, HD.2, R.7, FT.7A fasteners.
36. Step 36: Attach roof components (R.8, KCRRC) and sealing strips using FT.2 fasteners.
37. Step 37: Secure skylight ridge components (KCRRH, KCRBC.L, KCRBC.R) using FT.2 fasteners. Follow tips for screw locking on the skylight ridge: work from front to back, press down the upside of the ridge, and use pliers to pull down the ridge in the middle part while locking screws.
38. Step 38: Attach sealing strips (FR.12, FR.13, FR.10, FR.9, FR.14) and panels using FT.2, FT.7, FT.7A fasteners.
39. Step 39: Attach sealing strips (FR.1, FR.9, FR.10, FR.11) and panels using FT.2, FT.7, FT.7A fasteners.
40. Step 40: Attach sealing strips (FR.1, FR.14, FR.2) and panels using FT.2, FT.7, FT.7A fasteners.
41. Step 41: Attach components using FT.2, FT.3, FR.2 fasteners.
42. Step 42: Install window/vent components (WIR4.OUT, WIR4.IN, WIR4.PC) and sealing strips, attaching panels using FT.2, FT.4 fasteners.
43. Step 43: Attach components (D.1, D.2, D.3, D.4) using FT.6 fasteners.
44. Step 44: Attach components (HD.8, DH.5, DH) using FT.2, FT.3, FT.6 fasteners.
45. Step 45: Attach components (HD.9, HD.7) using FT.6, FT.11 fasteners.
46. Step 46: Install window/vent components (WIR4.OUT, WIR4.IN, WIR4.PC) and sealing strips, attaching panels using FT.2, FT.4 fasteners.
47. Step 47: Attach components (D.5, D.3, D.4) using FT.6 fasteners.
48. Step 48: Attach components (HD.7, HD.10, DH.5, DH) using FT.2, FT.3, FT.6 fasteners.
49. Step 49: Secure components using FT.6 fasteners.
50. Step 50: Attach panels (FT.1, F.19).
51. Step 51: Install pads (2pcs). If the door does not close smoothly, level the shed or adjust the hinges.
52. Step 52: Attach components (HD.6, FT.2, FT.12).
53. Step 53: Installation Completed.

Help Center

If you encounter any difficulties during assembly, such as assembly issues or missing parts, please contact customer support.

Disclaimer

Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from incorrect attachment, improper use, inadequate maintenance, unapproved modification, or neglect of this product.