Ingenuity Spring & Sprout 2-in-1 Activity Jumper & Table - First Forest

Safety Warnings

WARNING: TO PREVENT SERIOUS INJURY OR DEATH

Use the product ONLY if the child meets ALL of the following conditions:

• Is at least 6 months of age.
• Can sit up unassisted.
• Is less than 30" tall (76.2 cm).
• Weighs less than 25 lbs. (11 kg).

DO NOT use the product in dangerous conditions or situations.

DO NOT allow children who can stand or walk on their own to sit in the seat of the product.

ALWAYS keep child in view while the child is in product. Never leave child unattended. [Warning Symbol] ⚠️

NEVER move the unit while the child is in the seat.

DO NOT add additional strings or straps to product.

DO NOT use any hardware or parts other than that supplied.

FALL HAZARD: Babies can FALL from unit resulting in head injuries.

• NEVER leave child unattended. ALWAYS keep child in view while the child is in product.
• NEVER use near stairs.
• To avoid tip over, place the product on a flat, level surface.
• DO NOT place the product on an elevated surface.
• A child's movement can slide the product.
• DO NOT place baby in the toy storage bag. The toy storage bag is not a seat.
• REMOVE bounce pad in activity table mode. DO NOT allow child to stand, jump, or play on bounce pad in activity table mode.

STRANGULATION HAZARD: Strings can cause STRANGULATION.

• DO NOT place items with a string around child's neck, such as hood strings or pacifier cords.
• DO NOT suspend strings over product or attach strings to toys.
• For indoor use only.

IMPORTANT

• Adult assembly required.
• Please read all instructions before assembly and use.
• Care should be taken in unpacking and assembly.
• Examine product frequently for damaged, missing, or loose parts.
• DO NOT use if any parts are missing, damaged, or broken.
• Contact Kids2 for replacement parts and instructions if needed. Never substitute parts.

Battery Information

The product requires (2) size AA (LR6) alkaline batteries (not included).

CAUTION: Follow the battery guidelines in this section. Otherwise, battery life may be shortened, or the batteries may leak or rupture. [Caution Symbol] ⚠️

• Always keep batteries away from children.
• Do not mix old and new batteries.
• Do not mix alkaline, standard, or rechargeable batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Install the batteries so that the polarity of each one matches the markings in the battery compartment.
• Do not short-circuit the batteries.
• Do not store batteries in areas that have extreme temperatures (such as attics, garages, or automobiles).
• Remove exhausted batteries from the battery compartment.
• Never attempt to recharge a battery unless it is specifically marked "rechargeable."
• Rechargeable batteries are to be removed from the toy before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not use rechargeable alkaline batteries in a Ni-Cad or Ni-MH battery charger.
• Please use the correct disposal method for batteries. [Recycle Symbol] ♻️
• Remove batteries before putting the product into storage for a prolonged period of time.
• Weak batteries cause erratic product operation, including distorted sound, dimming or failing light, and slow or non-working motorized parts. Because each electrical component requires a different operating voltage, replace the batteries when any function fails to operate.
• Do not dispose of product or batteries in fire, batteries may explode or leak.

Care and Cleaning

• Fabric Seat: Machine wash the fabric seat in cold water. Use a gentle wash cycle with no bleach. Tumble dry, using low heat.
• Plastic Parts: Wipe clean with damp cloth and mild soap. Air dry. Do not immerse in water.
• Toy Storage Bag: Wipe clean with damp cloth. Air dry. Do not use machine wash.

Parts List

Assembly Instructions

Step 1: Attach Legs to Feet

Take three legs (Part 1) and three feet (Part 2). Align each leg with a foot and push until it clicks securely into place. Repeat for all three leg and foot sets. [Diagram shows legs being attached to feet with a click sound indicator].

Step 2: Attach Legs to Table Top

Take the three assembled leg and foot units. Align the top of each leg with the corresponding attachment points on the underside of the table top (Part 3). Push down firmly on each leg until it clicks and locks into place. Ensure the central support structure integrates correctly. A checkmark [✓] indicates correct attachment, while a cross [X] indicates incorrect. Repeat for all three legs. [Diagram shows legs being attached to the underside of the table top, with a central support structure connecting them].

Step 3: Attach Bounce Pad

Place the bounce pad (Part 4) onto the base of the jumper frame. Align the attachment points on the bounce pad with the corresponding slots on the frame. Push down firmly on three points around the edge of the bounce pad until it is securely attached. [Diagram shows the bounce pad being placed and secured to the jumper base with a click sound indicator].

Step 4: Attach Toy Stations

Attach the various toy stations to the hubs, and then attach the hubs to the table top:

• Attach the House Toy Station (Part 8) and Tree Toy Station (Part 9) to the House Chaser Toy Station Hub (Part 12). Then, attach this hub assembly to the table top.
• Attach the Tree Toy Station (Part 9) to a Toy Station Hub (Part 7). Then, attach this hub assembly to the table top.
• Attach the Bunny Toy Station (Part 10) to a Toy Station Hub (Part 7). Then, attach this hub assembly to the table top.
• Attach the Bead Chaser Toy Station (Part 5) to the Bead Chaser Toy Station Hub (Part 11). Then, attach this hub assembly to the table top.
• [Diagrams illustrate these attachments, showing parts 5, 8, 9, 10, 11, 12, and 7 being connected and attached to the table top].

Step 5: Attach Seat Pad to Seat Carrier

Place the Seat Pad (Part 15) into the Seat Carrier (Part 14). Align the edges and secure the pad using the designated attachment points (A and B). Ensure the two 'B' clips are fastened. [Diagram shows the seat pad being placed into the seat carrier and secured with clips].

Step 6: Attach Seat Carrier to Jumper Frame

Take the assembled seat carrier with the seat pad. Align the attachment points on the seat carrier with the corresponding slots on the main jumper frame. Push down firmly on the seat carrier until it clicks securely into place. Repeat for all six attachment points. [Diagram shows the seat carrier being attached to the jumper frame with multiple connection points indicated].

Step 7: Secure Seat Carrier

Ensure the seat carrier is fully secured to the jumper frame by checking all attachment points. [Diagram illustrates securing the seat carrier].

Step 8: Final Assembly

The Ingenuity Spring & Sprout Activity Jumper & Table is now assembled. [Diagram shows the completed product].

Usage Instructions

Adjusting Bounce Pad Height

The bounce pad height can be adjusted to suit your child's growth. Follow these steps:

1. Locate the adjustment mechanism on the base of the jumper.
2. Select the desired height position (1, 2, 3, or 4) by moving the adjustment mechanism.
3. Ensure the bounce pad is level and secure.
4. Check that your child's feet can rest flat on the surface at the chosen height. [Diagrams illustrate the height adjustment mechanism and correct foot placement].

Removing the Seat Pad for Cleaning

To clean the seat pad:

1. Carefully remove the seat pad from the seat carrier by releasing the six attachment clips. [Diagram shows the seat pad being detached from the seat carrier by releasing clips].
2. The seat pad can now be washed according to the care instructions.

Removing Batteries (Bear Toy Station)

To remove or replace batteries in the Bear Toy Station:

1. Locate the battery compartment cover on the Bear Toy Station (Part 6).
2. Use a screwdriver to open the battery compartment cover.
3. Remove the old batteries and insert two new AA/LR6 batteries, ensuring correct polarity (+/-).
4. Replace the battery compartment cover and secure it with the screwdriver. [Diagrams illustrate opening the compartment, inserting batteries, and closing the cover].

Activity Table Mode with Toy Storage

To convert the jumper to Activity Table Mode with Toy Storage:

1. Remove the seat pad from the seat carrier.
2. Remove the seat carrier from the jumper frame by releasing the attachment clips.
3. Remove the bounce pad from the jumper base.
4. Attach the toy storage bag to the designated points on the jumper frame. [Diagrams illustrate these steps, showing the removal of the seat pad, seat carrier, and bounce pad, followed by the attachment of the toy storage bag].

FCC Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This statement also applies to the French version (Déclaration FCC / CAN ICES-3 (B) / NMB-3(B)).