BEA DT1 Motion And Presence Sensor For Automatic Sliding Doors User Guide
File info: application/pdf · 4 pages · 940.43KB
IXIO-DT1 | BEA Sensors
Extracted Text
ENGLISH QUICK GUIDE Refer to the User's Guide for full instructions. IXIO-DT1 MOTION AND PRESENCE SENSOR FOR AUTOMATIC SLIDING DOORS Software version 6.3 / Configuration 42.4463.03 (refer to Admin menu for product software vesion) ! READ BEFORE BEGINNING INSTALLATION & SETUP ! The sensor should be mounted securely to avoid extreme vibrations. Do not cover the sensor. Avoid moving objects and light sources in the detection field. Avoid highly reflective objects in the infrared field. The door control unit and the header cover profile must be correctly grounded. Only trained and qualified personnel are recommended for installation and setup of the sensor. Following installation, always test for proper operation (according to ANSI 156.10) before leaving the premises. The warranty is invalid if unauthorized repairs are made or attempted by unauthorized personnel. This device can be expected to comply with Part 15 of the FCC Rules, provided it is assembled in exact accordance with the instructions provided with this kit. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1 MOUNTING & WIRING Refer to Application Note 76.0035 if an IXIO Spacer is required for the given application. SENSOR DOOR CONTROL RED BLACK BROWN BLUE WHITE (COM) POWER SUPPLY POWER SUPPLY SAFETY INPUT SAFETY INPUT OPENING INPUT POWER 12 � 24 VAC/VDC 12 � 30 VDC 2.5 W (max) max. 2 in YELLOW (N.C) GREEN (N.O.) PURPLE PURPLE OPENING INPUT OPENING INPUT TEST OUTPUT* TEST OUTPUT* TEST low: < 1 V high: > 10 V (30 V max.) response time: typ. < 5 ms Sensor connectivity (power and relays) must utilize only the supplied harness. Sensor power must be supplied from a Class 2 supply source limited to 15 W. Sensor is intended to be monitored for proper operation by the door operator or system. Harness shall be routed separated from any Mains or non-Class 2 voltage cable for correct operation or shall be rated for the Mains voltage, and suitable protection and routing means shall be used according to National and Local Codes to prevent damage to the harness and/or IXIO sensor. 75.1219.02 IXIO-DT1 QG 20240722 Page 1 of 4 2 RADAR OPENING IMPULSE FIELD ANGLE WIDTH TILT ROTATE 3 INFRARED SAFETY FIELD ANGLE Activate the visible spots. WIDTH or WIDE or NARROW DOOR C1 C2 max. 3 in CLOSER AWAY Adjust the angle, if necessary. Always verify the actual detection field width by walk-testing according to ANSI 156.10. 4 SETUP STEP OUT OF THE INFRARED FIELD! SETUP 1 (QUICK) reference picture either hold the knob for 2 seconds, or use the remote control buttons as specified + 2 s OR SETUP 2 (ASSISTED) test of full door cycle + reference picture either hold the knob for 4 seconds, or use the remote control buttons as specified + + 4 s OR TEST THE PROPER OPERATION OF THE INSTALLATION BEFORE LEAVING THE PREMISES! COLORS (green) Motion detection Page 2 of 4 (red) Presence detection LED SIGNALS BEHAVIORS LED flashes LED flashes red-green LED flashes quickly x LED flashes x times LED is off 75.1219.02 IXIO-DT1 QG 20240722 OVERVIEW OF SETTINGS RC BUTTONS 01 23456789 Back More RAD: FIELDSIZE small > > > > > > > > large RAD: SHAPE LCD: "narrow" and "wide" setting options (default = wide) Remote Control: = wide, = narrow AIR: WIDTH see note 1 AIR: OUTPUT TEST More Back DeEner/NO Energ/NC NC NO Energ/NC DeEner/NO NC NO off on on+auto see note 2 see note 3 BASIC + + Back More RAD: FIELDSIZE small > > > > > RAD: IMMUNITY low > > > > RAD: DIRECTION off bi uni MTF RAD: HOLDTIME auto 1 s 2 s 3 s 4 s 5 s RAD: REENTRY small > > > > > RAD: OUTPUT DeEner/NO Energ/NC NC NO Energ/NC DeEner/NO NC NO AIR: IMMUNITY normal enhanced AIR: WIDTH > > > large > > > high uni + reentry see note 4 6 s 7 s 8 s 9 s see note 5 > > > large see note 2 mode B see note 1 ADVANCED AIR: NUMBER AIR: PRESENCE TIME AIR: FREQ 1 2 30 s 1 min 2 min 5 min 10 min 20 min 60 min infinte A B AIR: OUTPUT TEST REDIRECTION DeEner/NO Energ/NC NC NO Energ/NC DeEner/NO NC NO off on on+auto R1 MW R1MWorIR R2 IR R2 IR see note 2 see note 3 see note 6 FACTORY RESET full reset partial reset see note 7 Back More factory value motion (green) presence (red) ZIP CODE ID # CONFIG P/N all parameter settings in zipped format (see application note on ZIP CODE � 76.0024) unique ID-number Download the BEA DECODER app for a quick overview of settings SOFT P/N ERROR LOG last 10 errors + day indication AIR: SPOTVIEW view of spot(s) that trigger detection AIR: C1 ENERG signal amplitude received on curtain AIR: C2 ENERG signal amplitude received on curtain 2 POWERSUPPLY supply voltage at power connector OPERATINGTIME power duration since first startup RESET LOG PASSWORD ADMIN delete all saved errors LCD and remote control password (0000= no password) enter code to access admin mode 75.1219.02 IXIO-DT1 QG 20240722 Page 3 of 4 DIAGNOSTICS OVERVIEW OF SETTINGS (cont.) Note 1 Note 2 Note 3 Note 4 Note 5 Note 6 Note 7 Always use a screwdriver when making further AIR adjustments to the arrow position on the sensor. RADAR AIR NO = normally open NC = normally closed DeEner = de-energized relay (active) Energ = energized relay (passive) NO = normally open NC = normally closed The sensor LED will briefly flash RED during monitoring communication with door control. This indicates that external monitoring is functional. Monitoring functionality must be active on the sensor and door control, and monitoring wires must be properly connected to the door control. MTF = uni-directional with motion-tracking feature uni + reentry: BEA recommends only adjusting using the LCD Auto mode evaluates traffic rate and adjusts hold time from 0.5 to 3 seconds REDIRECTION setting (F1 on remote control): R1-MW, R2-IR (f1=0): R1 = MW (i.e. motion detection) R2 = IR (i.e. presence detection) partial: outputs are not reset R1-MW or IR, R2-IR (F1=1): R1 = MW or IR (i.e. motion or presence detection) R2 = IR (i.e. presence detection) TECHNICAL SPECIFICATIONS Output Test/Monitoring input: Supply voltage: Mounting height: Relay 1 Relay 2 Electromechanical relay (potential and polarity free) Max. contact current: 1 A Max. contact voltage: 30 VAC Adjustable hold time: 0.5 � 9 s Solid-state relay (potential and polarity free) Max. contact current: 100 mA Max. contact voltage: 42 VDC / 30 VAC Sensitivity: Low: < 1 V High: > 10 V (max. 30 V) Response time on test request: typical < 5 ms 12 � 24 VAC �10% 12 � 30 VDC �10% to be operated from SELV-compatible power supplies only 6'6" � 11'6" local regulations may impact acceptable mounting height (pedestrian applications only) Specifications are subject to change without prior notice. All values measured in specific conditions. �BEA | Original Instructions | PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose. BEA, Inc. strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/ gates, and factory-trained for the type of door/gate system. Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards. Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer's recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service call � examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code). Verify that all appropriate industry signage, warning labels, and placards are in place. Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 General Tech Questions: techservices-us@BEAsensors.com | www.BEAsensors.com Page 4 of 4 75.1219.02 IXIO-DT1 QG 20240722
Homepage | BEA Sensors