User Manual for EVJUICION models including: 1-2 EV AC Charging Pile, 1-2 EV, AC Charging Pile, Charging Pile
EVJUICION Tesla Charger Level 1-2 EV Charger for Tesla 110V-240V 16Amp WiFi/APP Enabled Mobile Connector NEMA 6-20 Plug 5-15 Adapter 20ft Extension Cord Compatible with All Tesla Models 3/Y/X/S : Automotive
AC Charging pile User's Manual Welcome Thank you for choosing our electric vehicle charger. This EV charger supports smart charging with a smart control APP, which can be accessed through optional WIFI or Bluetooth. It includes features such as remote start/stop, reservation, setting the output current, and monitoring the charging status, among others. Please use your SMART phone to scan the following QR code and download the latest APP. APP This documentation provides general descriptions and technical characteristics of our products' performance. However, it is not intended as a substitute for determining the suitability or reliability of these products for specific user applications. Users must perform appropriate and comprehensive risk analysis, evaluation, and testing of the products concerning their relevant specific application or use. Our company is not liable for any misuse of the information herein. If you have suggestions for improvements or amendments or have identified any errors in this publication, please notify us. Reproduction of this document, except for personal, non-commercial use, requires written permission from our company. Hypertext links to this document are prohibited. Please consult this document at your own risk, using a non-exclusive license. All other rights are reserved. To ensure safety and compliance with regulations, please follow all relevant state, regional, and local safety regulations when installing and using this product. Only the manufacturer should conduct repairs to components to maintain adherence to documented system data and for safety reasons. When using these devices for applications with specific technical safety requirements, be sure to follow the relevant instructions for proper operation and safety. Ensure to use our company's software or approved software with our hardware products to avoid injury, harm, or improper operation. page1 CONTENTS Welcome .................................................................................................................... 1 Safety Information ................................................................................................... 3 1. Product Overview .............................................................................................4 2. List of Accessories........................................................................................... 5 3. Main Technical Parameters ............................................................................ 6 4. Installation Instructions ..................................................................................7 5. Smart Phone APP User Guide ...................................................................... 9 6. Charger User Guide........................................................................................ 10 7. Error Codes ......................................................................................................10 8. Recycling and Disposal................................................................................. 11 page2 Safety Information Before using or maintaining this product, it is important to read the following safety instructions carefully. Failure to follow and implement all the specified instructions and procedures may invalidate the warranty, and therefore our company will not be liable for any claims. · Do not open the charger. · Do not use the charger if it is damaged. · Do not use an extension lead on the charging cable. · Do not touch or insert foreign objects into the plugs. · Do not install the charger near flammable, explosive, or combustible materials. · The charger must be kept out of reach of children. · The EV charger must be connected to a protective earth conductor. · The electrical installation must comply with all local applicable safety requirements, standards, and guidelines. · No modifications should be made to the EV charger. · Components should not be changed or replaced by the end-user or unqualified personnel. page3 1. Product Overview Our EV chargers are designed to provide a smart, stable, and reliable charging experience for electric vehicle owners. 1.1 Main Features of the Products LED Charging Indicator: LED Charging indicator Blue Standby; Green (flashing) Charging in progress; Red Error. page4 1.2 Model Description Z BA A 4 03 E - C S S: unidirectional charging station; B: bidirectional charging station Connection mode (C: single-head gun; B: double-head gun) Display mode (C: LCD, T: TFT, N: No screen, E: LED ) Power (02-2KW, 03-3.5KW, 07-7KW, 09-9.6KW, 11-11KW, 22-22KW) Input voltage (1-120V, 2-220V, 3-380V, 4-240V) Country of shipment (C: China, U: European, A: American) A: AC charging pile; D: DC charging pile; BA : portable AC charging pile Series intelligent AC charging station 2. List of Accessories page5 3. Main Technical Parameters Product Name Case Material Product Size Cable Length Mounting Wire-in Input Voltage Input Frequency Rated Power Output Voltage Output Current Standby Power Consumption Working Temperature Storage Temperature Single-phase Charger PC+945A-V0 W210*D81.5*H55mm 6M Installation-free Bottom Feed AC 240V±20% 60±3Hz 3.8KW AC 240V±20% 16A (max) 5W - 2 5 ~ + 5 0 - 2 5 ~ + 5 0 page6 Working Altitude Ingress Protection Cooling Mode Safety Standard MTBF (Mean Time Between Failures Special Protection warranty <2000m TYPE-3R Natural Cooling UL 2231,UL 2594 two years UV protection design Over voltage protection, Under-voltage protection, Over-current protection, Leakage protection, Grounding remind, Temperature protection, Waterproof protection, Power-off protection, Data protection. two years Insulation Resistance: The insulation resistance between the input loop and ground, output loop and input to output of the charging station is 10M. 4. Installation Instructions All work on the equipment must only be carried out by qualified personnel who have read and fully understood all safety information and installation requirements contained in this manual. page7 4.1 Installation Environment Requirements 1) This AC smart charging station are suitable for outdoor application with its TYPE-3R structure. 2) Please ensure that the ambient temperature is in the range of -25to + 5 0 . Do not mount the EV charger in areas containing highly flammable materials or gases. Do not mount the EV charger in potentially explosive atmospheres. 4.2 Before Installation 1 ) Make sure an appropriate MCB (Main Circuit Breaker) is installed upstream of the AC power supply to the charger. 2)Use protection. The selected circuit protection device must integrate the appropriate residual current device (RCD) and the corresponding electrical load overcurrent protection device. Use copper cables that comply with local wiring regulations. The selected cable must be able to withstand a continuous load of up to 50A for each period page8 5. Smart Phone APP User Guide (with optional WIFI/Bluetooth module) 5.1 To obtain the APP User Guide, please use your smart phone to scan the following QR code. APP user Guide page9 6. Charger User Guide 6.1 Charge Control 1) When the AC power is connected, and the charging gun is not inserted, the LED indicator remains steady blue, indicating standby mode. 2) To start charging, use your mobile phone to scan the two-dimensional code on the charging gun. The two-dimensional code is affixed to the rear cover of the charging pile and supports scanning ( APP download ). 6.2 Charging State 1) After inserting the charging gun, the blue light will stay steady on. Once you connect to the APP, click on the "Quick Charging" option on your phone screen, and the LED light of the charging pile will turn green with a breathing effect. Attention: Don't unplug the EV Charger before the charging is completed, as there's risk of electric shock. 7. Error Codes 7.1 Before charging and starting, the following detection should be performed: ground leakage, relay adhesion, over-current, over-voltage, under-voltage, and overtemperature detection. If any of these values exceed the set limit, an error will be reported. 7.2 After the charging starts, if an error occurs, it will be reported on the portable pile, and the LED indicator of the charging pile will be steady red. Error Code Fault Description E01 Ground fault E02 Earth leakage protection E03 Input over voltage page10 Processing Mode Check whether the PE cable is not properly connected. Unplug the charging gun and reset the safety switch. Warranty service is required if errors persist. Wait for the voltage to return to normal after use. E04 Input under voltage Wait for the voltage to return to normal after use E05 Over current protection Unplug the charging gun and reset the safety switch. E06 EV Charger is abnormal Reinsert the charging gun. E09 Fire-zero line reverse connection Check whether the live and neutral wires are reversed. E12 Charging pile temperature is too high Turn off the air switch and use it after the temperature returns to normal. Unplug the charging gun and reset the E20 Relay open circuit safety switch. Warranty service is required if errors persist. Unplug the charging gun and reset the E21 Relay bonding safety switch. Warranty service is required if errors persist. E22 Relay temperature is too high Turn off the air switch and use it after the temperature returns to normal. 8. Recycling and Disposal 1) This device is intended for charging electric vehicles and is subject to the EU directive 2012/19/EU on waste electrical and electronic equipment (WEEE). 2) Disposal of this device must be carried out in accordance with the national and regional regulations for electrical and electronic equipment. 3) Old devices and batteries should not be disposed of with household waste or bulky waste. Before disposing of the device, it should be rendered inoperable. 4) Dispose of the packaging material in the region's designated collection container for cardboard, paper, and plastics. page11WPS 文字