Valberg 10000836-BL9 Vacuum Cleaner

Introduction

Thank you for choosing this Valberg product. Selected, tested, and recommended by ELECTRO DEPOT, Valberg products ensure simple use, reliable performance, and impeccable quality. With this appliance, you can be confident that each use will bring satisfaction.

Welcome to ELECTRO DEPOT.

Visit our website: www.electrodepot.fr or www.electrodepot.be.

Warranty Conditions

This product is guaranteed against faults caused by defects in manufacturing or the materials used for a period of two years, starting from the date of purchase. This warranty does not cover defects or damage caused by failure to install the device correctly, incorrect use of the product, or excessive wear and tear. Proof of purchase is required.

Product Overview

Parts

• A Dust cup release button
• B Handle
• C Power cable rewind button
• D +/- buttons to increase or decrease the suction
• E ON/OFF button
• F Air vent
• G Floor brush storage slot
• H Dust cup
• I Hose-connecting inlet
• J Flexible hose
• K Metal extension tube (telescopic)
• L Floor brush (smooth floors and carpets)
• M Pedal ? (to extend and retract the brush)
• N Long crevice tool (for hard-to-reach places)
• O Mini turbo brush (to remove stubborn dirt from furniture, smooth floors and carpets)

Appliance Description

Unpack and remove all labels from the unit. Please check that all of the unit's parts are included and intact. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.

Keep all packaging out of the reach of children. There is a risk of accidents if children play with packaging materials.

Intended Use

This vacuum cleaner is for household use only. It has not been designed for industrial or professional use by cleaning companies. Any other use may damage the unit or cause injury.

Specifications

Declaration of Conformity

ELECTRO DEPOT declares that this unit complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity can be viewed on the website: http://www.electrodepot.fr/sav/notices/

Product Usage

Assembly/Disassembly

To Assemble

1. Connect the dust cup lid to the unit's body by pushing until it clicks into place.
2. Insert the flexible hose into the hose-connecting inlet on the unit's body until it clicks into place.
3. Insert the metal tube into the flexible hose.
4. To adjust the length of the metal tube, push the pushbutton backwards and extend the tube.
5. Attach one of the following accessories by inserting it into the metal tube or flexible hose:
   • Floor brush for various types of flooring. Press the pedal ? to retract the brush (for carpets) or extend it (for smooth floors).
   • Mini turbo brush for furniture.
   • Long crevice tool for hard-to-reach places.

Insert the plug into the mains socket

The power cable can be extended up to the yellow mark. If the red mark is visible, then you have pulled the cable out too far.

To Disassemble

• Make sure the unit is turned off and disconnect the plug from the mains socket.
• Detach the brushes, crevice tool, and metal tube by twisting to pull them apart.

6. To remove the flexible hose, press the hose release button and pull out the hose.
7. Press the cable rewind button ? to store the cable away.
8. Insert the floor brush into the back of the unit for easy storage.

Operation

Once the unit is assembled and plugged in, it is ready for use.

9. Press the ON/OFF button ▶️ to turn the unit on or off.
10. Press the + or - button to increase or decrease the level of suction.
11. Use the handle ?️ to carry the vacuum.

Cleaning and Maintenance

General Cleaning

ATTENTION:

• Always unplug the unit from the power supply before cleaning. ?
• Never immerse the unit in water or any other liquid. ?
• Detach all accessories from the main unit.
• Remove any blockages from the accessories.
• Clean the unit with a soft, slightly damp cloth. Make sure that no liquid enters the unit.
• When cleaning the unit, never use abrasive products, metal brushes, scourers, wire sponges, or sharp utensils.
• After cleaning, dry the unit thoroughly.

Cleaning the Dust Cup and Filters

Empty the dust cup whenever it is full or there is a loss of suction.

1. Press the two dust cup release buttons to attach or detach the cup.
2. Detach the dust cup lid.
3. Remove the filter.
4. Remove the central part of the filter over a bin.
5. Detach the base of the dust cup to empty the contents.

Wipe the dust cup and the central part of the filter with a dry cloth. The filter can be cleaned under running water. ?

Cleaning the Air Outlet Filter

1. Press the air outlet pushbutton to open it.
2. Press the pushbutton to remove the HEPA filter.

The HEPA filter can be cleaned under running water. ? Let all the parts dry.

WARNING: To avoid damaging the unit, only use and insert dry filters! ⚠️

Reassemble all the parts in reverse order.

Disassembling and Cleaning the Brushes

Floor Brush:

17. Detach the brush from the tube.

Mini Turbo Brush:

18. Detach the brush from the tube and remove the locking system.
19. Lift up the transparent cover.
20. Remove the roller and gently pull the brush out.

Clean the brush bristles. Let them dry completely. Reposition the brush and re-attach the locking system.

Troubleshooting

Storage

• Always unplug the unit before storing it. ?
• Store the unit in a fresh, dry, and dust-free place, out of the reach of children and pets. ??
• Please retain the packaging to store your unit when it is not in use for an extended period of time. ?