Overview. Wireless Wallstations with integrated LED indicators are available in a range of configurations for customized light level control.
www.osram.us Wireless Wallstations Wiring and installation manual Light is OSRAM Overview Wireless Wallstations with integrated LED indicators are available in a range of configurations for customized light level control. The wireless wallstations obtain their operating power from two AA alkaline batteries and feature several options for functionality depending on the model installed. The wireless wallstations obtain their address during the commissioning process and no actions are required during installation. Wireless Wallstation 2-Button 3-Scene 5-Scene 3-Zone 6-Zone Ordering Code EN-WS-2B-ZB-WH EN-WS-SC3-ZB-WH EN-WS-SC5-ZB-WH EN-WS-ZC3-ZB-WH EN-WS-ZC6-ZB-WH Works with ENCELIUM® EXTEND Networked LMS X X X X X Works with ENCELIUM EDGETM Standalone LMS X X X Note Tip Important Safeguards When using electrical equipment, basic safety precautions should always ! beSTfOoPllowed including the following: ---- READ AND FOLLOW ALL SAFETY INSTRUCTIONS. ---- Do not mount near gas or electric heaters. ---- Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. ---- The use of accessory equipment is not recommended by OSRAM as it may cause an unsafe condition. Note ---- Do notTipuse this equipment for other than the intended use. ! SSATVOEP THESE INSTRUCTIONS 2 Battery Installation Two AA alkaline batteries are provided with each wireless wallstation. When replacing these batteries, use only alkaline-type batteries. Install the batteries according to the battery compartment markings. Dispose of used battery promptly. Keep away from children. Do not disassemble and do not dispose in fire. Battery slots Wallstation - Rear view Wallstation Installation Electrical Metal Device Box: Install the mounting bracket using the supplied screws. Ensure that the OSRAM logo and SINGLE GANG labels are facing up. Mounting bracket J-Box 3 Wallstation Installation (continued) Low Voltage Device Box: Mounting bracket Old Work Low Voltage Mounting Bracket Place the wallstation assembly into the mounting plate and push gently until `clicks' are heard. This confirms that the pieces are secured. 4 Decorator Plate Installation The wireless wallstation can also be installed with an off-the-shelf decoratorstyle wall plate. Multi-gang WS installations require multi-gang decorator wall plates. Remove the button assembly from the OSRAM wall plate. This can be achieved by pressing the wall plate with your thumbs near the button assembly while grasping the OSRAM Wall Plate. Install the supplied wall strips to the wireless wallstation until they snap in. 5 Decorator Plate Installation (continued) Orient the mounting bracket such that the DECORATOR and MULTI GANG labels are facing up. Insert the wallstation button assembly into the mounting plate until `clicks' are heard. Clicks confirm that the pieces are secured. Install the mounting bracket using the supplied screws. Install the decorator plate using screws supplied with the decorator plate. 6 Installation Notes Consult the OSRAM website for the most up-to-date version of the wireless system design guide and install this product according to the guidelines. The Wireless Wallstation is to be installed in dry, indoor locations ONLY. Do not install the Wireless Wallstation in damp locations. Damp locations are defined as: interior locations subject to moderate degrees of moisture, such as basements, barns, cold-storage warehouses, as well as partially protected locations under canopies, marquees and open roofed porches. Troubleshooting There are no user-serviceable parts inside the Wallstation. Please return the device to OSRAM if service is required. Regulatory Approvals This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment under FCC rules. This equipment has been tested and found to comply with Industry Canada ICES-003 Issue 5 (CAN ICES-3 (A)/NMB-3(A)). Contains FCC ID: H79DFZM-E7220 Contains IC ID: 4259B-DFZM7220 7 OSRAM SYLVANIA Inc. 200 Ballardvale Street Wilmington, MA 01887 USA 888-531-7573 www.osram.us/ds OSRAM is a registered trademarks of OSRAM GmbH. ENCELIUM EXTEND is a registered trademark of OSRAM SYLVANIA Inc. ENCELIUM EDGE is a trademark of OSRAM SYLVANIA Inc. Specifications subject to change without notice.. LMS134R2 4-18 © 2018 OSRAM SYLVANIA Inc.Adobe PDF Library 15.0 Adobe InDesign CC 13.0 (Macintosh)