BUNK-BED ASSEMBLY INSTRUCTIONS
SAFETY WARNINGS AND GENERAL NOTES:
- Follow the information on the warnings on the bunk bed end structure and on the carton. Do not remove the warning label from the bed.
- Always use the recommended size mattress on mattress support, or both, to help prevent the likelihood of entrapment or falls.
- Do not allow children under 6 years of age to use the upper bunk.
- Periodically check and ensure the guardrail, ladder and other components are in their proper position, free from damage, and all connectors are tight.
- Do not allow horseplay on or under beds.
- Always prohibit jumping on the bed.
- Prohibit more than one person on upper bunk.
- Always use the ladder for entering and leaving the upper bunk.
- Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
- Use of a night-light may provide added safety precaution for a child using the upper bunk.
- Always use guardrails on both long sides of the upper bunk.
- If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should be placed against the wall to prevent entrapment between the bed and the wall.
- The use of water or sleep flotation mattresses is prohibited.
- STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed.
- Keep these instructions for future reference.
- We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet.
- Be certain all staples are out of the box before beginning assembly on the shipping carton.
- USE ONLY MATTRESSES WHICH ARE AS THE TABLE BELOW ON UPPER AND ON LOWER BUNKS.
| Length | Width | Thickness | |
|---|---|---|---|
| Down bed Bed type Twin Standard | 74" - 75" | 38½" | 8" max |
| Up bed (bunk bed and tribed included) Bed type Twin Standard | 74"-75" | 38½" | 6" max |
18. SURFACE OF MATTRESS MUST BE AT LEAST 5” (127MM) BELOW THE UPPER EDGE OF GUARDRAILS.
19. Replacement Parts:
Replacement Parts, including additional guardrails, may be obtained from any of our dealers.
[Recyclable garbage symbol]
PART LIST
Diagram showing all parts and hardware with corresponding numbers and letters.
Hardware List:
- A: 4*60-51pcs
- B: 4*30-4pcs
- C: 4*16-32pcs
- D: 4*45-4pcs
- E: M6-4pcs
- F: 40X40-24pcs
- G: M4X60-3pcs
Assembly Steps
Step 1: Use hardware A, C, F, G to connect parts #3, #3, #3, #6, #3, #3, #18 together to get component 1.
Step 2: Use hardware F, A, G to connect parts #1 and #6 together to get component 2.
Step 3: Use hardware F, C, G to connect parts #2, #7, #8, #9, #10, #18 together to get component 3.
Step 4: Use hardware A and G to connect component 1, component 2, and component 3 together to get a left bed.
Step 5: Use hardware A, C, F, G to connect parts #3, #4, #6, #13, #18 together to get component 4.
Step 6: Use hardware F, A, and G to connect parts #1 and #6 together to get component 5.
Step 7: Use hardware F, C, G to connect parts #2, #7, #8, #9, #10, #18 together to get component 6.
Step 8: Use hardware A and G to connect component 4, component 5, and component 6 together to get a right bed.
Step 9: Use hardware F, A, B, G, connect parts #5 and #14 together, reassemble 2 to get two identical components 7.
Step 10: Use hardware C, G, connect the two components 7 to the left bed and the right bed.
Step 11: Use #9 and #10 to insert #14 holes in order, and #10 needs to correspond to #14 screw holes.
Step 12: Use hardware C and G to tighten #10 with component 7.
Step 13: Use hardware A and G to continue to install #11 to specify the location of the drawing.
Step 14: Use hardware A and G to continue to install #12 at the specified location of the drawing.
Step 15: Use hardware A and G to connect #11 and #16 to the bed and tighten them.
Step 16: Use hardware E, A and G to connect #17 left and right from the bed and tighten it.
Step 17: Use A, H and E accessories to fix and tighten #19 to the left and right of the bed respectively. (New upgrade, add #19 support foot, stronger)
Step 18: Use A, H and E accessories to fix and tighten #19 to the left and right of the bed respectively. (New upgrade, add #19 support foot, stronger)
Completed attic bed
Diagram showing the completed bunk bed.
Note: Tighten all the steps before use, thank you.
