Sagemcom F5685 LGB-VMB Safety Instructions

General Safety Precautions

To avoid any risk of fire, electric shock, or injury, the product must be used and installed in compliance with basic safety precautions:

• Always follow the installation instructions provided with the product.
• Do not connect or use the product during thunderstorms.
• Acoustic shocks may occur in the earpiece during voice communication, potentially causing deafness due to excessive acoustic pressure.
• The product must be installed inside a building and its case must not be opened.
• Connect an Ethernet cable to the rear panel's Ethernet port and to a computer's Ethernet port.
• Connect only to in-house equipment (SELV interface).
• Connect a telephony cable to the telephony port on the rear panel and to a phone's telephony port.
• Keep plastic bags out of reach of children as they pose a suffocation risk.
• The product is designed for vertical use.
• If wall-mounting, use screws and dowels appropriate for the wall material (recommended screw diameter: 3.5 mm, length: 30 mm or more; recommended dowel diameter: 5 mm, length: 30 mm).

Climatic Conditions

This product is designed for use in an office or room with a maximum ambient temperature of 40°C (104°F). Avoid installation in areas with excessive sunshine or heat radiation. Do not install in locations with heat build-up (e.g., on or under other electrical equipment) or exposure to moisture or condensation. Install in an environment classified as pollution degree 2 (pollution-free environment with dry, non-conducting pollution).

Water and Moisture

Do not install the product in damp or dusty environments. Avoid contact with water or other liquids. No liquid should enter the product. Do not use the product near water outlets (bath, washbasin, washing machine), in damp basements, or near swimming pools. If liquid enters the product, switch it off immediately or unplug the power cord. Continued use may cause electric discharge or fire. Allow the product to dry completely if moved from a cold to a warm environment to prevent condensation.

Cleaning and Maintenance

Disconnect the product from the mains socket and computer before cleaning. Do not use detergents, aerosols, chemicals, alcohol, benzene, diluents, or flammable products, as they may cause fire. Do not dismantle the product; internal parts are not user-replaceable and opening covers may expose you to dangerous voltages. Incorrect re-assembly can lead to electric shock. Contact customer service for repairs or servicing.

Power Supply

Use only the supplied power unit and accessories. Connect to the mains according to installation instructions and the identification label on the power unit. Using non-recommended power sources may cause overheating, deformation, electric discharge, or fire.

Accessibility & Electrical Overload

Ensure the power unit is easily accessible and close to the equipment for quick unplugging in case of issues. Avoid plugging too many devices into a mains socket block or extension cords to reduce fire or electric shock risks.

Damage Requiring Repair

Unplug the appliance and contact qualified after-sales service if:

• The power supply or plug is damaged.
• A supplied cable is damaged or frayed.
• Liquid has been spilled into the appliance, or it has been exposed to rain or water.
• The appliance does not function normally or shows performance variations.
• The appliance has fallen or is damaged.
• There are signs of overheating.

If small metal objects enter the appliance, disconnect it immediately (risk of electric shock) and contact Customer Service. Do not reconnect until foreign bodies are removed. Unplug immediately if you notice a burning smell or smoke. Do not open the product yourself due to the risk of electric shock.

Regulatory Compliance

This equipment is designed for private use within a building. Ethernet and telephony ports are intended for indoor cable circuits within the installation building. Wireless device usage may be prohibited in certain environments; seek permission before use if unsure. Sagemcom Broadband SAS is not responsible for non-compliance with regulations or radio interference caused by non-compliance.

UK Declaration of Conformity:

Sagemcom confirms that this product complies with the Product Security and Telecommunications infrastructure (Security Requirements for Relevant Connectable Products) Regulations 2023.

The full text of the declaration of conformity is available at https://support.sagemcom.com/en.

EU Declaration of Conformity:

Sagemcom confirms that this product complies with the fundamental requirements and other relevant provisions of directive 2014/53/EU.

Sagemcom confirms that this product complies with Radio Equipment Regulations 2017.

This marking certifies compliance with health and safety of users, electromagnetic compatibility, correct use of radio frequency spectrum, and reduction of environmental impact.

Radio Frequency Information:

This device operates within the 2.4 GHz and 5 GHz frequency ranges. To limit radio frequency exposure, keep the device at least 20 cm from people.

Frequency bands and maximum transmitted power:

• 2400-2483.5 MHz: 100 mW
• 5150-5350 MHz: 200 mW
• 5470-5725 MHz: 1 W
• 5725-5850 MHz: 200 mW

Restrictions:

This device can only be used in the UK as it may use frequencies in the 5725-5850 MHz band.

This radio equipment is subject to restrictions in Belgium (BE), Bulgaria (BG), Czech Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES), France (FR), Croatia (HR), Italia (IT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE), North Ireland (UK(NI)), Norway (NO), Switzerland (CH), Iceland (IS), Turkey (TR), Lichtenstein (LI).

Wi-Fi 5 GHz: The 5150-5350 MHz band is limited to indoor use.

This radio equipment is also subject to restrictions in the United Kingdom (UK). The 5150 to 5350 MHz frequency range is restricted to indoor use in the UK.

Ecodesign Requirements for External Power Supplies

COMMISSION REGULATION (EU) 2019/1782 of 1 October 2019

Manufacturer: Sagemcom Broadband SAS

Address: CS 39000, 92271 BOIS-COLOMBES CEDEX, France

Off mode power consumption: 0.06 W

Network Stand-by power consumption (all network ports connected and wireless ports activated): 10.8 W

Network Stand-by power consumption (after 10 minutes inactivity): 7.8 W

Wireless interfaces (Wi-Fi) can be disabled via the graphical user interface.

External Power Supply Model Identifiers and Specifications:

Environmental Protection & Disposal

This symbol indicates that the product must be collected separately and not disposed of with household waste. The European Union has a specific collection and recycling scheme for which manufacturers are responsible. Utilize local collection points (recycling centers, sorted waste collection). Retail outlets will take back end-of-life equipment free of charge when purchasing equivalent equipment. Sort packaging waste for easier recycling.

Electrical and electronic appliances may contain essential but potentially dangerous components if not handled or disposed of properly. Do not dispose of with household waste.

For professional users: Refer to supplier's instructions.

If rented or deposited: Contact your service provider.

Help protect the environment!

Laser Safety

Radiation emitted by laser devices may be harmful. Avoid direct or indirect exposure to laser radiation. Do not look at optical components. Laser rays used on optical fiber are invisible but dangerous to human eyes, posing a risk of irreversible blindness.

Class 1 Laser Product

Accessories Information

Electrical equipment may include:

1. A power supply (AC adapter and power cord).
2. The device itself.

Refer to the EU and UK declaration of conformity for the latest accessory information. The full EU and UK Declaration of Conformity can be found at https://support.sagemcom.com or requested from Sagemcom Broadband SAS, 4 ALLEE DES MESSAGERIES, 92270 BOIS-COLOMBES - France. Contact: reclamations@sagemcom.com.