JABLOTRON JA-111H TRB Busmodule
Interface for Wired Detectors
Manufacturer: JABLOTRON a.s.
Introduction
This document provides information for the JABLOTRON JA-111H TRB busmodule. It is a machine translation from the original English version. For clarity or doubts, please refer to the original document. Contact Technical Support for any errors or questions.
The JA-111H TRB is a component of the JABLOTRON system, designed to connect wired detectors with NC/NO outputs to the control panel bus. It supplies power to the detector and reports activation, tampering, and fault conditions. Installation requires a trained technician holding a valid certificate from an authorized distributor.
Installation
⚠️ Important: Always disconnect power before connecting the module to the system bus.
The current consumption of the connected detector must not exceed 50 mA. The module's power output is not protected against overload.
The module is intended for installation inside a standard wired detector (with contact outputs). However, its extended wires allow for installation outside the detector in a protected junction box.
Installation Steps:
- Install the module in a suitable location within the detector or in a protected junction box near the detector. The cable length should not exceed 3 meters. Ensure that the module, when installed inside the detector, does not cause short circuits due to poor insulation.
- Connect the wires to the detector according to Figure 1.
- Connect the bus cable and then switch on the power to the control panel.
- Ensure the control panel is in service mode.
- Close the detector cover with the installed module.
Diagram and Wiring Description
Figure 1: Module Components and Wiring
This figure shows the internal components of the JA-111H TRB module and the connection of its wires. It depicts the BUS terminals, a production code identifier, and the module's four wires. A yellow LED indicates a fault or unregistered device, while a red LED flashes to signal the activation of any input.
The module's wires are color-coded and have specific functions:
- Red wire: +12V – Provides power to the detector.
- Black wire: GND – Common ground connection.
- White wire: INP – Connects to the alarm input of the detector.
- Blue wire: TMP – Connects to the tamper input of the detector.
- Yellow wire: TRB – Connects to the trouble input of the detector.
The diagram also illustrates the BUS connection terminals and the internal connections within a detector, labeled as GND, +12V, PIR, TMP, and TRB.
Technical Specifications
| Parameter | Value |
|---|---|
| Power Supply | 12 V DC (9...15 V) from control panel bus |
| Standby Current Consumption | 8 mA (+ consumption of connected devices) |
| Maximum Current Consumption | 12 mA (+ consumption of connected devices) |
| Maximum Detector Current | 50 mA |
| Control Panel Type (ACE) | Type B |
| Dimensions | 16 x 30 x 12 mm |
| Weight | 8 grams |
| Classification | Security Class 2 / Environmental Class II (according to EN 50131-1) |
| Environment | Indoor general use |
| Operating Temperature | -10 °C to +40 °C |
| Average Humidity | 75% RH, non-condensing |
| Certifying Body | Trezor Test s.r.o. (No. 3025), Kiwa Nederland B.V. |
| Conformity Standards | EN 50130-4, EN 55032, T 031, EN 50131-1, -3, EN IEC 63000 |
Compliance and Disposal
JABLOTRON a.s. hereby declares that the product JA-111H TRB complies with the relevant Union harmonisation legislation: Directives No. 2014/30/EU and 2011/65/EU. The original Declaration of Conformity can be found at www.jablotron.com – Downloads Section.
Note on Disposal: Proper disposal of this product helps conserve valuable resources and prevents potential negative effects on human health and the environment from improper waste handling. Return the product to your dealer or contact your local municipality for information on the nearest collection point.
For an electronic version of this document (available in other languages) or an installation version for JA-100, scan the provided QR code.
