Somfy Smoove 1 & 4 RTS Controllers

1. Introduction

Smoove 1 RTS

The Smoove 1 RTS is a wall-mounted controller for Somfy RTS (Radio Technology Somfy) enabled window coverings. It features the following controls:

• A. Button: Used for raising, switching on, or opening/tilting the window covering.
• B. "my" button: Used to stop the window covering or go to a favorite preset position.
• C. Button: Used for lowering, switching off, or closing/tilting the window covering.
• D. Channel selection indicators: Lights indicating the currently selected channel.
• E. Programming (PROG) button: Located on the backside of the unit, used for pairing and configuration.

A visual representation shows the Smoove 1 unit with these buttons clearly labeled. An internal view of the Smoove RTS module shows a circular unit with connection terminals and a dial.

Smoove 4 RTS

The Smoove 4 RTS offers control for up to four different groups of window coverings. It shares similar functionality with the Smoove 1 but adds channel selection capabilities. It features:

• A. Button: Raise, switch on, open, tilt.
• B. "my" button: Stop, go to favorite position.
• C. Button: Lower, switch off, close, tilt.
• D. Channel selection indicators: Multiple indicators to show the active channel.
• E. Programming (PROG) button: Located on the backside of the unit.

A visual representation shows the Smoove 4 unit with these buttons and channel indicators.

2. Installation

The Smoove RTS can be installed on a clean, flat interior wall within 35 feet of the window coverings.

Components:

• A. Mounting frame: A rectangular plastic bracket with four screw holes at the corners, designed for wall attachment.
• B. Smoove frame: The decorative outer frame that attaches to the mounting frame.
• C. Smoove 1 or 4 module: The main control unit that clips into the assembly.

Installation Steps:

1. Install the mounting frame using the provided countersunk screws into the corners of the plate on the wall.
2. Snap the Smoove frame onto the mounting plate, ensuring the notch faces downward.
3. Clip the Smoove RTS module onto the assembly.
4. The product can also be mounted using double-sided tape (e.g., 3M tape).

? Note: Locating the module near a metal frame or surface may impede the product's operation.

3. Operation for Smoove 1

The Smoove 1 allows for easy control of your window coverings.

Pairing a Smoove 1 to a Window Covering

1. Press and hold the Programming (PROG) button on the window covering motor until the covering moves up and down. Note: You have 2 minutes to complete RTS programming.
2. Press the Programming (PROG) button (E) on the back of the Smoove 1 until the window covering begins to move up and down.
3. The Smoove 1 is now paired with the window covering motor.

Daily Use

• To open or close the window covering, press the ⬆️ (A) or ⬇️ (C) button on the Smoove 1.
• To stop the window covering at a specific position, press the ⭐ ("my") button (B).

Creating Preset Positions

To create a preset position:

• Adjust the window covering to the desired position.
• Press the ⭐ ("my") button on the Smoove 1 until the window covering moves up and down. The preset is now activated.

To delete a preset position:

• Press the ⭐ ("my") button. The window covering will move to the preset position.
• Press the ⭐ ("my") button again until the window covering moves up and down. The preset position has been deleted.

Daily Use of Preset Positions

• Briefly press the ⭐ ("my") button. The window covering will move to the preset position.

4. Operation for Smoove 4

The Smoove 4 operates up to four different groups of window coverings. You build these groupings as you pair your Smoove 4 to each window covering controller.

Pairing a Smoove 4 to a Window Covering and Creating Channels

1. Press and hold the Programming (PROG) button on the window covering motor until the covering moves up and down. Note: You have 2 minutes to complete RTS programming.
2. Assign the window covering to a channel by selecting that channel (D) on the Smoove 4.
3. Press the Programming (PROG) button (E) on the Smoove 4.
4. The window covering will move up and down, indicating a successful pairing.
5. Repeat this procedure for all window coverings, assigning them to channels.

To Remove or Change a Channel:

1. Press the Programming (PROG) button on the window covering motor.
2. Press the channel button (D) on the Smoove 4 to which the window covering is assigned.
3. Press the Programming (PROG) button (E). The window covering will move up and down, indicating it is now removed from the Smoove 4 and its assigned channel.

Daily Use

• Select a channel, then press the ⬆️ (A) or ⬇️ (C) to open or close the window covering.
• To stop the window covering at a specific position, press the ⭐ ("my") button (B).

Creating Preset Positions

To create a preset position:

• Press the channel number (E).
• Adjust the window coverings to the desired position.
• Press the ⭐ ("my") button (B) until the window coverings move up and down. The preset is now activated.

To delete a preset position:

• Press the channel number (E).
• Press the ⭐ ("my") button (B). The window coverings will move to a preset position.
• Press the ⭐ ("my") button (B) again until the window coverings move up and down. The preset position has been deleted.

Daily Use of Preset Positions

• Press the channel button (E).
• Press the ⭐ ("my") button (B).
• The window covering will move to the preset position.

5. Battery Replacement

Follow these steps to replace the battery in your Smoove controller:

1. Unclip the frame using a small flathead screwdriver to open it, engaging the small groove shown in the diagram.
2. Remove the old battery and insert a new CR 2430 3V battery, ensuring the positive (+) side is facing up.
3. Replace the frame and module onto the mounting frame by pressing them back into their original position.

A visual representation shows a screwdriver being used to open the unit, followed by the battery compartment with a CR2430 battery.

6. Troubleshooting

7. Replacing a Lost or Broken Smoove 1 or 4 Controller

To replace a lost or broken remote, follow these steps with the new transmitter:

1. Press and hold the Programming (PROG) button on the window covering motor until the window covering moves up and down.
2. Press the Programming (PROG) button (E) on the back of the new Smoove 1 (or 4) until the window covering begins to move up and down.
3. The new Smoove controller is now paired with the window covering motor.
4. Follow the installed motor's steps to set the upper and lower limits.

Important Information

? Note: Visit https://store.somfysystems.com/ to purchase an additional or replacement product.

This device is FCC certified and complies with Part 15 of the FCC rules. RTS compatibility: RTS transmitters are capable of operating any RTS motor.

❗ CAUTION: AS WITH ANY PRODUCT INVOLVING GENERATION OF ELECTRICAL POWER, CAUTION MUST BE USED AT ALL TIMES. PLEASE CAREFULLY READ AND FOLLOW ALL OF THE INSTRUCTIONS.