Installation Guide for Walmart models including: Hitch HT-X30201 Hyper Tough Automotive Tri Ball Mount With Hook, Hitch HT-X30201, Hyper Tough Automotive Tri Ball Mount With Hook, Automotive Tri Ball Mount With Hook, Tri Ball Mount With Hook, Mount With Hook, With Hook, Hook
Auto Parts & Auto Accessories - Over 4000 Auto Parts, Aftermarket Parts, Truck Accessories & Car Accessories
Hitch Installation Instruction REV.20240901 Part# HT-X30201 Application For 2009-2020 Dodge Journey Hardware List Hitch Parts HW B (For Hitch Installation) Item Part Name QTY Description Item Part Name A Hitch Body 1 B/C Mounting Brackets 1# Square Hole Spacer 2 6X32X75-13 4# Fishwire QTY Description 2 B-Driver Side C-Passenger Side 2 For installing bolts 2# Hex Flange nut 6 M12X1.75 5# Square Hole Spacer 4 6X25.4X51-13 3# Carriage bolt 6 M12X1.75-40 6# Wedge Spacer 2 M12 HW A (For Hitch Assembly) 7# Hex Bolts 8# Flat Washers 6 M12X1.75-35 9# Lock Washers 10 M12 10# Hex Nuts 6 M12 4 M12X1.75 Gross Load Capacity When Used As A Weight Carrying Hitch: 4000 LBS. Trailer Weight & 400 LBS. Tongue Weight. Gross Load Capacity When Used As A Weight Distribution Hitch: 4000 LBS. Trailer Weight & 400 LBS. Tongue Weight. ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY. *** No Drilling Required C B REAR A The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation. Thank you for choosing our product! Page1 of 3 Hitch Installation Instruction REV.20240901 Part# HT-X30201 Application For 2009-2020 Dodge Journey Step Description 1 Assemble Hitch Body (A) and Mounting Brackets (B, C) with (6) M12X1.75-35mm Hex Bolts, (10) M12 Flat Washers, (6) M12 Lock Washers, (4) M12 Hex Nuts.(Hardware in "HW A"). Lower exhaust by removing rubber isolators (3 each side) as shown in the above diagram. NOTE: Support exhaust from underneath after lowering. 2 Fishwire the carriage bolts and small square hole spacers through the space between the bumper beam and the end of the frame rail for both sides. 3 Fishwire the remaining carriage bolts and large spacers through the bumper beam and into position. 4 5 Raise hitch into position with the "wedge" shaped spacers between as shown and secure with hex flange nuts. NOTE: If equipped, temporarily disconnect driver side electrical connector for clearance while securing the hitch. The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation. Thank you for choosing our product! Page2 of 3 Hitch Installation Instruction Part# HT-X30201 Application For 2009-2020 Dodge Journey REV.20240901 Torque M12 fasteners to 58 ft-lbs. 6 Raise exhaust back into position and reinstall the (6) rubber isolators removed in Step 1. NOTE: Apply lubricant or soapy water to ease installation. 7 ***Periodically Check The Receiver Hitch To Ensure That All Fasteners *** Are Tight & All Structural Components Are Sound. The instruction here is for your reference only. We strongly recommend the professional installer for best result. We are not responsible for any damage caused by the installation. Thank you for choosing our product! Page3 of 3WPS 文字