DiO 1.0 Wireless Switch
Important Safety Information
Warning: Risk of explosion if the battery is not replaced correctly. Replace only with the same type or an equivalent type.
This product contains a coin/button cell battery. If swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
0. Video Tutorial
To make understanding and installing our solutions easier, we have created video tutorials. You can view them on our YouTube channel youtube.com/c/dio-connected-home in the Playlists tab. You can also view them on our website www.chacon.com in the Support tab.
1. Install the Wireless Switch
1.1 Activating the Switch
Remove the switch plate (see paragraph 2) and remove the tab on the battery.
1.2 Installing the Unit
You have two options:
- Use the supplied double-sided adhesives to attach the wireless switch to the wall, making sure the LED on the switch is facing up.
- Use small screws (not included). For this option, remove the wireless switch frame and place the 2 screws into the slot, making sure the LED is at the top of the switch. Then replace the frame.
2. Changing the Battery
The switch LED will become dim when the battery is low.
To change the battery:
- Remove the front frame and faceplate of the switch.
- Using a small flat screwdriver, remove the battery compartment by pressing the small notch inwards while pulling downwards.
- Replace the old battery with a new CR2032 - 3V type, making sure to place it with the '+' side facing up.
- Replace the battery compartment, faceplate, and the front frame until you hear a click.
3. Linking the Switch with the Receiver
- Connect the receiver (module, socket, connected switch).
- Bring the wireless switch close to the DiO or DiO Connect receiver and press the receiver's learn button (see receiver manual); the receiver LED flashes.
- Press the ON button of the switch to link them.
- The LED on the module/socket flashes twice to confirm the association.
4. Deleting the Link Between the Wireless Switch and a DiO Receiver
If you want to delete a receiver from the switch:
- Bring the switch close to the receiver to be deleted and press the receiver's learn button (socket, module - see product manual); the receiver LED flashes.
- Press the "OFF" button on the switch (top of the switch, where the LED is); the LED on the receiver will blink twice to confirm the deletion.
5. Use
ON/OFF Control
Press the ON button of the wireless switch once to turn your light, device, roller shutter, etc. on, or the OFF button once to turn it off.
Dimmer (only with a dimmer module, socket)
Press the ON button of the wireless switch twice; the brightness starts to increase/decrease; press ON again to stop the increase/decrease. When you turn off the light with the OFF button, the last brightness level selected will be retained in the receiver memory.
DiO 1.0 receivers (lighting module, shutter module, socket, bulb, etc.) can be controlled individually or in conjunction with other receivers (e.g.: a DiO switch closes the shutter linked to a DiO shutter module and at the same time turns on the lamp connected to the lighting module, and the DiO remote control turns the lamp on and off individually).
6. Troubleshooting
The receiver is not activated when the remote control is pressed:
- Check the polarity of the battery and/or that it is not flat.
- Make sure that the wireless switch is linked to the receiver and that the receiver is connected correctly.
- Check the status of the receiver memory (see receiver manual).
Important: The range between the receiver and the remote control is 50 m, but this may be reduced by the thickness of the walls or a currently wireless environment. A minimum distance of 1-2 m is necessary between two DiO receivers (module, socket and/or bulb). Do not use in a damp location.
7. Technical Specifications
| Specification | Details |
|---|---|
| Protocol | DiO 1.0 |
| Frequency | 433.92 MHz |
| Max transmitted radio frequency power | <20 mW |
| Operating temperature | -10 to 35°C |
| Transmission range | 50 m (in free field) |
| Battery | CR2032 3V (included) |
| Number of channels | 1 |
| Dimensions | 86 x 85 x 13 mm |
Indoor use (IP20). Do not use in a damp environment.
8. Supplementing Your Installation
Supplement your installation with DiO solutions to control your heating, lighting, roller shutters, or garden, or to use video surveillance to keep an eye on what is happening at home. Easy, high-quality, scalable and economical... Learn about all of the DiO Connected Home solutions at www.chacon.com.
Recycling and Compliance
In accordance with European WEEE directives (2002/96/EC) and directives concerning accumulators (2006/66/EC), any electrical or electronic device or accumulator must be collected separately by a local system specialising in the collection of such waste. Do not dispose of these products with ordinary waste. Check the regulations in force. The symbol shaped like a waste bin indicates that this product must not be disposed of with household waste in any EU country. To prevent any risk to the environment or human health due to uncontrolled scrapping, recycle the product in a responsible manner. This will promote the sustainable use of material resources. To return your used device, use the return and collection systems, or contact the original dealer. The dealer will recycle it in accordance with regulatory provisions.
CHACON declares that device 54717-v2 conforms with the requirements and provisions of Directive RED 2014/53/EU. The complete text of the EU declaration of conformity is available at the following Internet address: www.chacon.com/conformity
Support: www.chacon.com/support
Version: V2.1 211028
