Hooke Road BXG.8255 Front Bumper Installation Guide
Product Overview
This document provides installation instructions for the Hooke Road BXG.8255 Front Bumper, designed for Ford F-150 models (2018-2020, excluding Raptor).
Package Contents
The bumper kit includes the following main components:
- Front Bumper Assembly (Main Body, Left Wing, Right Wing)
- Bull Bar
- License Plate Bracket (A1, A2, A3)
- Winch Power Control Box Bracket (optional)
Parts List
| Qty | Part Name | Size(mm) |
|---|---|---|
| 6 | Hex Bolt | M12*30 |
| 6 | Hex Bolt | M12*35 |
| 6 | Hex Bolt | M8*20 |
| 4 | Button Head Socket Cap Bolts Screws | M6*20 |
| 8 | Button Head Socket Cap Bolts Screws | M4*6 |
| 12 | Split Lock Washer | D12 |
| 6 | Split Lock Washer | D8 |
| 18 | Flat Washer | M12*30*2 |
| 6 | Flat Washer | M8*16*1 |
| 4 | Flat Washer | M6*12*1 |
| 6 | Hex Nuts | M12 |
| 4 | Flange Hex Lock Nuts | M8 |
| 4 | Nylon Insert Lock Nut | M6 |
| 2 | Nylon Round Spacer | M6*12*1.3 |
| 1 | L-Wrench | M4 |
Tools Required
- Drive Socket Ratchet Wrench
- 4mm Hex Bit Socket
- 10mm, 13mm, 19mm Wrench
- 13mm, 19mm Shallow Socket
Installation Time
Estimated installation time: About 2 hours. Recommended for 2-3 people. Actual time may vary based on mechanical skill level.
Important: Please verify all parts are present and read instructions carefully before starting installation!
Installation Instructions
Step 1: Remove Factory Bumper
Remove the factory front bumper and any related accessories from your vehicle.
Diagram Description: Image shows the front of a Ford F-150 with the original bumper removed, revealing the mounting points for the new bumper.
Step 2: Assemble Wings and Main Body
Attach the Left and Right Wings to the Main Body of the bumper. Use three (3) M12*30 Hex Bolts, three (3) D12 Split Lock Washers, and three (3) M12*30*2 Flat Washers for each side. Tighten these bolts securely.
Diagram Description: Diagram shows the connection points for the bumper wings to the main body. Dashed lines and arrows indicate the insertion of bolts, washers, and nuts. A separate image shows a close-up of these connection points with fasteners installed, highlighted by red circles.
Step 3: Assemble Bull Bar
Attach the Bull Bar to the Main Body. Use four (4) M8*20 Hex Bolts, four (4) D8 Split Lock Washers, four (4) M8*16*1 Flat Washers, and four (4) M8 Hex Nuts. Tighten these bolts securely.
Diagram Description: Diagram illustrates the attachment of the Bull Bar to the Main Body of the bumper. Arrows indicate the use of M8*20 Hex Bolts, D8 Split Lock Washers, M8*16*1 Flat Washers, and M8 Hex Nuts. A photograph shows the bull bar mounted on the bumper.
Step 4: Assemble License Plate Bracket
Assemble the License Plate Bracket (components A1, A2, A3). Use two (2) M6*20 Button Head Socket Cap Bolts Screws, two (2) M6*12*1.3 Nylon Round Spacers, and two (2) M6 Nylon Insert Lock Nuts. Then, attach this assembly to the bumper using two (2) M6*20 Button Head Socket Cap Bolts Screws, two (2) M6*12*1 Flat Washers, and two (2) M6 Nylon Insert Lock Nuts.
Diagram Description: Diagrams for assembling and installing the License Plate Bracket. The top diagram shows the bracket components and fasteners. The middle diagram shows the bracket being attached to the bumper. The bottom image shows the installed bracket.
Step 5: Install Winch Power Control Box Bracket (Optional)
If you have a winch power control box, attach its bracket. Use two (2) M8*20 Hex Bolts, two (2) D8 Split Lock Washers, and two (2) M8*16*1 Flat Washers. This step is optional.
Diagram Description: Diagrams show the optional bracket being attached to the bumper assembly. A photograph shows the bracket and its connection points.
Step 6: Mount Bumper to Vehicle
Lift the assembled bumper and align it with the vehicle's mounting points. Secure the bumper using one (1) M12*35 Hex Bolt, one (1) D12 Split Lock Washer, one (1) M12*30*2 Flat Washer, and one (1) M12 Hex Nut for each side. Tighten all bolts.
Diagram Description: Diagram illustrates the bumper being mounted onto the vehicle. Arrows show the bumper aligning with mounting points on the vehicle frame. Red circles highlight the bolt locations. A photograph shows close-ups of the vehicle's mounting points with fasteners.
Step 7: Final Adjustments and Completion
Tighten all bolts on both sides after adjusting the bumper's height to ensure a proper distance between the bumper and the vehicle's frame.
Diagram Description: A front view of a blue Ford F-150 truck equipped with the fully installed Hooke Road BXG.8255 Front Bumper.
The installation is complete. Enjoy your new Hooke Road product!
Attention
Important Notes:
- Product parts in this instruction may differ slightly from actual product contents, but this generally does not affect installation.
- Please feel free to contact your distributor if you have any questions about your purchase.
Find more parts and information by searching "Hooke Road" on Google.
Share your vehicle and experience with the hashtag #hookeroad on social media.
▶️ YouTube ? Facebook ? Instagram ? TikTok
