Mean Well RCP-2000-12 AC/DC PSU module ( enclosure) 100 A 1200 W 12 V DC Mean Well RCP-2000-12 4021087006187
Mean Well RCP-2000-24 AC/DC PSU module ( enclosure) 80 A 2000 W 24 V DC Mean Well RCP-2000-24 4021087006170
2000W Front End Power Supply RCP-2000 series Features : Universal AC input / Full range Built-in 5V/0.3A, 12V/0.8A auxiliary power Built-in active PFC function, PF>0.98 High efficiency up to 92% Withstand 300VAC surge input for 5 seconds Protections: Short circuit / Overload / Over voltage / Over temperature 3 High Power density 21.4W/inch Forced air cooling by built-in DC fan with fan speed control Low profile:1U height Remote control for single unit Built-in remote sense function Output voltage trimming function Hot-swap operation PMBus serial communication AC OK, DC OK signal, fan fail, OTP alarm signal Internal OR-ing FET 3 years warranty Description : The RCP-2000 series are state of the art AC/DC frond-end rectifiers with 1U compact size and 21.4 W/in3 of high power density. They can provide up to 2000W per unit for the applications of servers, information technology equipment, networking, telecommunications, and wide range of industrial applications using distributed power architecture. Equipped with hot-swap function and PMBus communication protocol, RCP-2000 can be assembled in 1U 19 rack and controlled/monitored by external device such as monitoring unit (RCP-CMU-1) or PC. SPECIFICATION - Single Unit MODEL RCP-2000-12 RCP-2000-24 RCP-2000-48 DC VOLTAGE 12V 24V 48V RATED CURRENT 100A CURRENT RANGE 0 ~ 100A RATED POWER 1200W RIPPLE & NOISE (max.) Note.2 150mVp-p 80A 0 ~ 80A 1920W 200mVp-p 42A 0 ~ 42A 2016W 300mVp-p OUTPUT VOLTAGE ADJ. RANGE 10.5 ~ 14V VOLTAGE TOLERANCE Note.3 ±2.0% LINE REGULATION ±1.0% LOAD REGULATION ±1.0% 21 ~ 28V ±1.0% ±0.5% ±0.5% 42 ~ 56V ±1.0% ±0.5% ±0.5% SETUP, RISE TIME HOLD UP TIME (Typ.) 1500ms, 60ms/230VAC at full load 16ms/230VAC at 75% load 10ms/230VAC at full load VOLTAGE RANGE Note.5 90 ~ 264VAC 127 ~ 370VDC INPUT FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 47 ~ 63Hz 0.98/230VAC at full load 86% 13A/115VAC 7A/230VAC COLD START 50A 90.5% 16A/115VAC 10A/230VAC 92% 16A/115VAC 10A/230VAC LEAKAGE CURRENT <1.1mA / 230VAC OVERLOAD 105 ~ 125% rated output power Protection type : Constant current limiting, unit will shut down o/p voltage after 5 sec. re-power on to recover PROTECTION OVER VOLTAGE 14.7 ~ 17.5V 29.5 ~ 35V Protection type : Shut down o/p voltage, re-power on to recover 57.6 ~ 67.2V OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down AUXILIARY POWER 5V @ 0.3A, 12V @ 0.8A REMOTE ON/OFF CONTROL By electrical signal or dry contact ON:short OFF:open REMOTE SENSE Compensate voltage drop on the load wiring up to 0.5V DC OK SIGNAL FUNCTION AC OK SIGNAL The isolated TTL signal out, refer to function manual The isolated TTL signal out, refer to function manual OUTPUT VOLTAGE TRIM Adjustment of output voltage, possible between 90 ~ 110% of rated output OVER TEMP WARNING Logic " High" for over temperature warning, refer to function manual, isolated signal FAN FAIL SIGNAL The isolated TTL signal out, refer to function manual WORKING TEMP. -40 ~ +70 (Refer to "Derating Curve") WORKING HUMIDITY 20 ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85, 10 ~ 95% RH TEMP. COEFFICIENT ±0.03%/ (0 ~ 50) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes File Name:RCP-2000-SPEC 2013-11-01 2000W Front End Power Supply RCP-2000 series MODEL RCP-2000-12 RCP-2000-24 RCP-2000-48 SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE (Note 4) EMC EMISSION UL60950-1, TUV EN60950-1 approved I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.7KVDC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH Compliance to EN55022 (CISPR22) Conduction Class B, Radiation Class A ; EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A MTBF 60.1K hrs min. MIL-HDBK-217F (25) OTHERS DIMENSION PACKING 295*127*41mm (L*W*H) 2Kg;6pcs/13Kg/1.04CUFT NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. 6. Output of all the RCP-2000 modules are connected in parallel in the rack. 7. Under parallel operation of more than one rack connecting together, ripple of the output voltage may be higher than the SPEC at light load condition. It will go back to normal ripple level once the output load is more than 10%. Mechanical Specification (Single Unit) Case No. 974A Unit:mm 41 CN501 2 95 SVR1 24 Air flow d ir e c t io n 13579 33 11 14 17 20 23 26 29 12 15 18 21 24 27 30 13 16 19 22 25 28 31 2 4 6 8 10 32 34 Input / Output Connector Pin No. Assignment(CN501) : Postronic PCIM34W13M400A1 Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment 1,2,3,4 +V 12 DA 17 ON/OFF 22 NC 5,6,7,8 -V 13 DB 18 A1 23 SDA 9 -V(signal) 14 +S 19 A2 24 SCL 10 +V(signal) 15 -S 20 A3 25 AC-OK 11 PV 16 A0 21 A4 26 DC-OK Pin No. 27 28 29 30 31 Assignment T-ALARM FAN-FAIL +5V-AUX + 12 V- A UX GND-AUX Pin No. 32 33 34 Assignment Mating Housing FG AC/L AC/N Postronic PCIM34W13F400A1 File Name:RCP-2000-SPEC 2013-11-01 2000W Front End Power Supply RCP-2000 series Block Diagram I/P EM I F I LT ER AC TIVE INR USH CURRENT LIMITING RECTIFIERS & PFC PO W E R SW IT CHIN G PFC CONTROL DETECTION CIR CUIT PW M CON TROL MCU O.T.P. FAN AU X PO W E R RECTIFIERS & FILTER O.V.P. DETEC TION CIR CUIT MCU RECTIFIERS & FILTER PFC fosc : 110KHz PWM fosc : 90KHz ORI NG FET ORING FET CONTROL TR A N S C E IV E R S +S +V -V -S PV DA/DB DATA IS O LAT ION 1 2V /0. 8A AU X POWER 5V/0 .3A T- Ala rm DC-O K AC-OK FAN FAIL SD A /S CL PM BUS ON/O FF Function Description of CN501 Pin No. Function Description 1,2,3,4 +V Positive output voltage 5,6,7,8 -V Negative output voltage. 9 -V -V Signal 10 +V +V Signal 11 PV Connection for output voltage trimming. The voltage can be trimmed within its defined range. (Note.1) 12,13 DA,DB Differential digital signal for parallel control. (Note.1) Positive sensing. The +S signal should be connected to the positive terminal of the load. The +S and -S leads should be 14 +S twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V. Negative sensing. The -S signal should be connected to the negative terminal of the load. The -S and +S leads should be 15 -S twisted in pair to minimize noise pick-up effect. The maximum line drop compensation is 0.5V. 16,18,19, A0,A1,A2, PMBus interface address lines. (Note.1) 20,21 A3,A4 The unit can turn the output on and off by electrical signal or dry contact between ON/OFF and +5V-AUX. (Note.2) 17 ON/OFF Short (4.5 ~ 5.5V) : Power ON ; Open (0 ~ 0.5V) : Power OFF ; The maximum input voltage is 5.5V. 22 NC Not use. 23 SDA Serial Data used in the PMBus interface. (Note.2) 24 SCL Serial Clock used in the PMBus interface. (Note.2) Low (0 ~ 0.5V) : When the input voltage is 87Vrms. 25 AC-OK High (4.5 ~ 5.5V) : When the input voltage in 75Vrms . The maximum sourcing current is 10mA and only for output. (Note.2) High (4.5 ~ 5.5V) : When the Vout 80%±5%. 26 DC-OK Low (0 ~ 0.5V) : When Vout 80%±5%. The maximum sourcing current is 10mA and only for output. (Note.2) High (4.5 ~ 5.5V) : When the internal temperature (TSW1 or TSW2 open) exceeds the limit of temperature alarm. 27 T-ALARM Low (0 ~ 0.5V) : When the internal temperature (TSW1 or TSW2 short) under the limit temperature. The maximum sourcing current is 10mA and only for output(Note.2) High (4.5 ~ 5.5V) : When the internal fan fail. 28 FA N - FA IL Low (0 ~ 0.5V) : When the internal fan is normal. The maximum sourcing current is 10mA and only for output(Note.2) Auxiliary voltage output, 4.5~5.5V, referenced to GND-AUX (pin 31). The maximum load current is 0.3A. This output has the 29 +5V-AUX built-in "Oring diodes" and is not controlled by the remote ON/OFF control. Auxiliary voltage output, 10.8~13.2V, referenced to GND-AUX (pin 31). The maximum load current is 0.8A. This output has 30 +12V-AUX the built-in "Oring diodes" and is not controlled by the remote ON/OFF control. 31 GND-AUX Auxiliary voltage output GND. The signal return is isolated from the output terminals (+V & -V). 32 FG AC Ground connection. 33 AC/L AC Line connection. 34 AC/N AC Neutral connection. Note1: Non-isolated signal, referenced to the output terminals (-V). Note2: Isolated signal, referenced to GND-AUX. File Name:RCP-2000-SPEC 2013-11-01 2000W Front End Power Supply RCP-2000 series Derating Curve Static Characteristics 100 80 230VAC Input only 60 50 40 20 100 90 80 75 12V 70 65 24V,48V 50 40 -40 -25 -10 0 15 30 50 60 70 (HORIZONTAL) 90 100 115 180 264 AMBIENT TEMPERATURE () INPUT VOLTAGE (VAC) 60Hz EFFICIENCY vs LOAD (48V Model) 94 92 90 88 86 84 82 10 20 30 40 50 60 70 80 90 100 LOAD DERATING LOAD(%) VS INPUT VOLTAGE INPUT / VOLTAGE MODEL >180VAC RCP-2000-12 100% 115VAC 95% RCP-2000-24 100% 80% RCP-2000-48 100% 80% 100VAC 90% 75% 75% 90VAC 80% 65% 65% Function Manual 1. Remote ON/OFF Control The PSU can be turned ON/OFF together or separately by using the "Remote ON/OFF" function. Between ON/OFF and +5V-AUX Output 17 ON/OFF RC P- 2000 SW Open OFF SW 29 +5 V-AUX SW Short ON 2. Voltage Drop Compensation 2.1 Remote Sense The remote sense compensates voltage drop on the load wiring up to 0.5V. +V +V 14 +S RC P- 2000 15 -S -V -V LOAD Sense lines sh ould be t wisted in pairs File Name:RCP-2000-SPEC 2013-11-01 2000W Front End Power Supply RCP-2000 series 2.2 Local Sense Notice : The +S,-S have to be connected to the +V,-V terminals locally in order to get the correct output voltage if the remote sensing is not used. RCP-2 000 +V 14 +S -V 15 -S 3. Output Voltage Trimming (1)Output voltage can be trimmed between 90~110% of its rated value by the following method. (2)+S & +V, -S & -V also need to be connected on CN501. RC P- 2000 14 +S +V -V 15 -S 11 PV 9 -V Signal L OA D 0~5V Add on 0~5V external voltage Vout 110 100 90 80 70 60 V 0 0.5 1.5 3 4.5 5 EXTERNAL VOLTAGE (DC) 4. Front Panel Indicators & Corresponding Signal at Function Pins Function LED Description * Signal PSU Output AC-OK GREEN When input voltage87V 0 ~ 0.5V ON AC-NG RED When input voltage 75V DC-OK GREEN When output voltage80%±5% of Vo rated. 4.5 ~ 5.5V OFF 0 ~ 0.5V ON DC-NG RED When output voltage80%±5% of Vo rated. 4.5 ~ 5.5V ON T-OK GREEN When the internal temperature (TSW1 & TSW2 short) is within safe limit 0 ~ 0.5V ON T-ALARM RED When the internal temperature (TSW1 or TSW2 open) exceeds the limit of temperature alarm 4.5 ~ 5.5V OFF *Signal between function pin and "GND-AUX". File Name:RCP-2000-SPEC 2013-11-01Foxit PhantomPDF Printer Version 5.0.0.0601