JJC BTR-S1 Wireless Remote Control

Product Overview

The JJC BTR-S1 Wireless Remote Control is compatible with Bluetooth low energy technology, designed for select Sony cameras. It allows wireless control of your camera from approximately 10m/32.8' in any direction. The BTR-S1 can be used for shooting still images, recording video, adjusting camera focus, zooming, and activating the camera's C1 or AF-ON function.

A LOCK switch is included to disable all buttons, preventing unintentional operations. The remote is portable, powered by a CR2032 battery, and replaces the Sony RMT-P1BT remote commander.

Package Includes

• Wireless Remote Control x 1
• CR2032 Battery x 1

Specifications

Transmission method: Bluetooth, GFSK modulation

Operating distance: Approx. 10m / 32.8'

Power: CR2032 battery

Dimension: Approx. 110 x 31.6 x 12.7mm (4.3 x 1.2 x 0.5")

Weight: Approx. 18g

Parts

• 1. Indicator Lamp
• 2. FOCUS/ZOOM Button
• 3. Shutter Release/Video Recording Button
• 4. AF-ON Button
• 5. C1 Button
• 6. LOCK Switch
• 7. ZOOM/FOCUS Switch
• 8. MOVIE/STILL Switch
• 9. Battery Compartment

Connecting the Remote Control and Camera

Before you start: Ensure the remote control's LOCK switch is in the position opposite to "LOCK".

1. On the camera, select MENU → [Bluetooth Function] → [On] (or similar path depending on camera model).
2. On the camera, select MENU → [Bluetooth Rmt Ctrl] → [On].
3. On the camera, select MENU → [Bluetooth Settings] → [Pairing].
4. On the remote control, press and hold the Shutter Release/Video Recording Button and the FOCUS/ZOOM Button (T button) simultaneously for at least 7 seconds.
5. When a confirmation message appears on the camera's screen, select [OK]. When pairing is complete, a "Paired." message will appear.

Re-pairing is required if:

• You use the remote control with a different camera.
• The camera's network settings have been reset.

Preventing Unintentional Operations

To prevent accidental button presses while carrying the remote:

1. Slide the LOCK switch to the "LOCK" position.
2. To enable the buttons, slide the LOCK switch to the position opposite to "LOCK".

Warning

• Do not use batteries not specified in the manual.
• Do not insert batteries incorrectly.
• Do not attempt to disassemble or repair the product.
• Keep batteries and small parts away from children. Seek medical attention if swallowed.
• Check regulations before using in airplanes or hospitals, as the product's electromagnetic waves may interfere with equipment.
• Adult supervision is required when children use the product.
• Do not expose the product to temperatures over 45°C (e.g., in a car).
• The product is not waterproof. Keep away from rain, snow, and high humidity.
• Do not clean with organic solvents or alcohol-based liquids.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement and can be used in portable exposure condition without restriction.