Craftsman 12.0 HP IC Electric Start 38" Mower Deck 5 Speed Transaxle Lawn Tractor
Model No. 917.254520
This manual provides information on assembly, operation, maintenance, and repair parts for your Craftsman Lawn Tractor.
Important Safety Rules
WARNING: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest covered, brush covered or grass covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or area laws. If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other States may have similar laws. Federal laws apply on federal lands.
- Know the controls and how to stop quickly. READ THIS OWNER'S MANUAL and instructions furnished with attachments.
- Do not allow children to operate the machine. Do not allow adults to operate it without proper instruction.
- Do not carry passengers. Do not mow when children and others are around.
- Always wear substantial footwear. Do not wear loose fitting clothing that could get caught in moving parts.
- Keep your eyes and mind on your tractor, mower, and the area being cut. Do not let other interests distract you.
- Do not attempt to operate your tractor or mower when not in the driver's seat.
- Always get on or off your tractor from the operator's left hand side.
- Clear the work area of objects (wire, rocks, etc.) which might be picked up and thrown.
- Disengage all attachment clutches before attempting to start the engine.
- Disengage power to attachments and stop the engine before leaving the operator's position.
- Disengage power to mower, stop the engine, and disconnect spark plug wire(s) from spark plug(s) before cleaning, making an adjustment, or repair. Be careful to avoid touching hot muffler or engine components.
- Disengage power to attachments when transporting or not in use.
- Take all possible precautions when leaving the vehicle unattended. Disengage the power take-off, lower the attachments, shift into neutral, set the parking brake, stop the engine, and remove the key.
- Do not stop or start suddenly when going uphill or downhill. Mow up and down the face of slopes (not greater than 15°), never across the face. Refer to page 47.
- Reduce speed on slopes and make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes.
- While going up or down slopes, place gear shift control lever in 1st gear position to negotiate the slope without stopping.
- Never mow in wet or slippery grass, when traction is unsure, or at a speed which could cause a skid.
- Stay alert for holes in the terrain and other hidden hazards. Keep away from drop-offs.
- Do not drive too close to creeks, ditches, and public highways.
- Exercise special care when mowing around fixed objects in order to prevent the blades from striking them. Never deliberately run tractor or mower into or over any foreign objects.
- Never shift gears until tractor comes to a stop.
- Never place hands or feet under the mower, in discharge chute, or near any moving parts while tractor or mower is running. Always keep clear of discharge chute.
- Use care when pulling loads or using heavy equipment.
- Use only approved drawbar hitch points.
- Limit loads to those you can safely control.
- Do not turn sharply. Use care when backing.
- Use counterweight or wheel weights when suggested in owner's manual.
- Watch out for traffic when crossing or near roadways.
- When using any attachments, never direct discharge of material toward bystanders nor allow anyone near the vehicle while in operation.
- Handle gasoline with care - it is highly flammable.
- Use approved gasoline containers.
- Never remove the fuel cap of the fuel tank or add gasoline to a running or hot engine or an engine that has not been allowed to cool for several minutes after running. Never fill tank indoors. Always clean up spilled gasoline.
- Open doors if the engine is run in the garage - exhaust fumes are dangerous. Do not run the engine indoors.
- Keep the vehicle and attachments in good operating condition, and keep safety devices in place and working.
- Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition.
- Never store the equipment with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.
- To reduce fire hazard, keep the engine free of grass, leaves, or excessive grease. Do not clean product while engine is running.
- Except for adjustments, DO NOT operate engine if air cleaner or cover directly over carburetor air intake is removed. Removal of such part could create a fire hazard.
- Do not operate without a muffler, or tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect periodically and replace if necessary.
- The vehicle and attachments should be stopped and inspected for damage after striking a foreign object, and the damage should be repaired before restarting and operating the equipment.
- Do not change the engine governor settings or overspeed the engine; severe damage or injury may result.
- When using the vehicle with mower, proceed as follows:
- Mow only in daylight or in good artificial light.
- Shut the engine off when unclogging chute.
- Check the blade mounting bolts for proper tightness at frequent intervals.
- Do not operate the mower without the entire grass catcher, on mowers so equipped, or the deflector shield in place.
- Disengage power to mower before backing up. Do not mow in reverse unless absolutely necessary and then only after careful observation of the entire area behind the mower.
- Under normal usage the grass catcher bag material is subject to deterioration and wear. It should be checked frequently for bag replacement Replacement bags should be checked to ensure compliance with the original manufacturer's recommendations or specifications.
Electrical Schematic
The tractor is equipped with a special alternator system where the lights are not connected to the battery but have their own electrical source. Because of this, the brightness of the lights will change with the engine speed. At idle speed, the lights will dim. As the engine is speeded up, the lights will become their brightest.
NOTE: If wiring insulated clips or cable ties were removed for servicing of the unit, they should be replaced to properly secure your wiring.
Legend:
- ● Non-removable connections
- ○ Removable connections
Repair Parts - Electrical
This section lists the part numbers for the electrical components of the 12 HP 38" Riding Lawn Tractor.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 124108X | Harness, Light Socket | 28 | 72240460 | Bolt Rd. Hd. Sq. Nk. 1/4 - 20 x 7-1/2 |
2 | 124904X | Harness, Wiring | 29 | 109081X | Solenoid |
3 | 109310X | Key, Molded | 30 | 109787X | Bezel Ignition |
4 | 110712X | Switch, Light | 31 | 109788X | Nut, Ignition |
5 | 7603J | Tray, Battery | 32 | 7192J | Cable Tie |
6 | 109596X | Clamp, Hose | 33 | 105687X | Tube, Plastic |
7 | STD365402 | Switch, Ignition | 34 | 121305X | Screw, Tap Hex Hd. #10 x 24 UNC |
8 | 108824X | Fuse, 30 Amp | 35 | STD601005 | Screw Slotted Pan Hd. No. 10-32 x 1/2 |
9 | STD551125 | Washer, Lock, 1/4 | 36 | 74641008 | Nut Keps No. 10-32 x 1/2 |
10 | 73350400 | Nut, Hex Jam 1/4 20 | 37 | 4171R | Battery Caps Set |
11 | 74780408 | Bolt, Hex, 1/4 20 x 1/2 Gr. 5 | 38 | 121264X | Lockwasher 1/4 internal Tooth |
12 | STD541425 | Nut, Keps 1/4 20 | 39 | 11150400 | Sheet, Instruction, Tractor, 15° - English |
13 | 4799J | Cable Assembly Insulated | 40 | 719J | Owner's Manual |
14 | 11050400 | Washer Lock, Ext. Tooth, 1/4 | |||
15 | 719J | Cover, Terminal | |||
16 | 5114J | Cable, Battery | |||
17 | 109553X | Switch, Interlock | |||
18 | 126718X | Switch, Plunger | |||
19 | 4207J | Cable, Battery | |||
20 | 74760412 | Bolt, Hex, 1/4 20 x 3/4 | |||
21 | STD551025 | Washer 9/32 x 5/8 x 16 Ga. | |||
22 | STD541025 | Nut, Hex 1/4-20 | |||
23 | 121265X | Battery, 12 V., 30 Amp | |||
24 | 102476X | Terminal Guard | |||
25 | 123198X | Wing Nut 1/4-20 | |||
26 | STD551125 | Washer, Lock Hvy Helical Spring |
Repair Parts - Chassis and Enclosures
This section lists the part numbers for the chassis and enclosure components of the 12 HP 38" Riding Lawn Tractor.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 124497X | Seat | 35 | 124479X | Washer, Black, Nylon |
2 | 17490612 | Screw, Hex Washer Thd. Roll 3/8-16 x 3/4 | 36 | 124355X | Chassis Assembly |
3 | 17490616 | Screw, Hex Washer Thd. Rolling 3/8-16 X 1 | 37 | 121306X | Drawbar |
4 | 105513X | Bracket-Pivot. Seat | 38 | 124294X | Pan Seat |
5 | 105529X | Bolt, Shoulder, 5/16 18 | 39 | 125880X | Decal Fender |
6 | 73680500 | Nut Crownlock 5/16 18 | 40 | 124492X | Decal, Grill, Craftsman |
7 | 124181X | Spring, Seat | 41 | 4900J | Decal, Clutch/Brake |
8 | 109872X | Fender | 42 | 105809X | Decal, Chassis, 5 Speed, 38" |
9 | STD523707 | Bolt, Fin Hex 3/8 x 16 UNC x 3/4 | 43 | 109199X | Decal, V-Belt Ground Drive |
10 | 17030808 | Screw, Spiderlock Hex #8 x 1/2 AB | 44 | 19132012 | Washer 13/32 x 1-1/4 x 12 Ga. |
11 | 73680600 | Nut, Crownlock 3/8-16 | 45 | 121440X | Guide Belt. Lower, Eng. Pulley, L.H. |
12 | 17490608 | Screw, Hex Washer Thd Roll 3/8 x 1/2 | 46 | 121441X | Guide Belt, Lower. Eng. Pulley. R.H. |
13 | 109873X | Bracket, Fender | 47 | 2751R | Clip |
14 | STD512505 | Bolt, Fin Hex 1/4 20 UNC x 1/2 | 48 | 19131614 | Washer 13/32 x 1 x 14 Ga. |
15 | 105476X | Spring, Seat, Compression | 49 | 72170410 | Bolt, RdHd 1/4 x 20 x 1-1/4 |
16 | 105475X | Footrest, L.H | 50 | 123976X | Bolt, RdHd 1/4 x 20 x 1-1/4 |
17 | STD533707 | Bolt, RdHdSqNk 3/8 16 UNC x 3/4 | 51 | 121251X | Bolt, Hex, Lg., Flange, Loc. 1/4-20 |
18 | STD551125 | Washer, Lock, Hvy Helical Spring | 52 | 121250X | Strip, Foam |
19 | STD523710 | Bolt, Fin Hex 3/8 x 16 UNC x 1 | 53 | 121249X | Spacer, Split |
20 | 19131312 | Washer 13/32 x 13/16 x 12 Ga. | 54 | 121246X | Bracket, Switch Mount |
21 | 124029X | Lens Assembly | 55 | 124489X | Decal Stripe Hood L.H. |
22 | 4207J | Spring, Extension | 56 | 124490X | Decal Stripe Hood R.H. |
23 | 124491X | Decal, 12 HP | 57 | 123913X | Bracket, Pivot, R.H. |
24 | 108631X | Decal, II | 58 | 123914X | Bracket, Pivot, L.H. |
25 | 122933X | Rivet, Ratchet, Nylon | 59 | 124040X | Grill |
26 | 124027X | Shield, Hood, Heat | 60 | 105037X | Foam, Strip 18" |
27 | 123665X | Deflector, Heat | 61 | 121144X | Bolt, Shoulder |
28 | 124025X | Hood Assembly | 62 | STD525010 | Bolt, Fin Hex 1/2-13 UNC x 1 Gr. 5 |
29 | 121248X | Bushing, Snap | 63 | 19171912 | Washer 17/32 x 1-3/16 x 12 Ga. |
30 | STD541437 | Nut, Crownlock 3/8 x 16 UNC | 64 | 106974X | Decal, Caution |
31 | 124027X | Shield, Hood, Heat | 65 | 750211 | Decal, USA |
32 | 124025X | Hood Assembly | 66 | 121248X | Bushing, Snap |
33 | 121248X | Bushing, Snap | 67 | STD541437 | Nut, Crownlock 3/8 x 16 UNC |
34 | STD541437 | Nut, Crownlock 3/8 x 16 UNC |
Repair Parts - Drive
This section lists the part numbers for the drive components of the 12 HP 38" Riding Lawn Tractor.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 124136X | Engine, 12 HP, Briggs and Stratton, Model Number 281707, Type Number 0412-01 | 48 | 123766X | Pulley, Idler |
2 | 105731X | Pulley, Engine | 49 | 123789X | Arm, Idier |
3 | 13200300 | Elbow STD 90 3/8-18 NPT | 50 | STD523715 | Bolt. Hex 3/8-16 x 1-1/2 |
4 | STD551143 | Washer, Lock, Hvy Helical Spring | 51 | 105709X | Spring, Return, Clutch |
5 | 74770720 | Bolt, Hex 7/16-20 x 1-1/4 | 52 | 110812X | Washer, Hardened |
6 | 125907X | V-Belt, Drive | 53 | 12000039 | Ring, Klip |
7 | 125610X | Muffler | 54 | 105710X | Link, Clutch |
8 | 125593X | Gasket | 55 | STD561210 | Pin, Cotter 1/8 x 3/4 |
9 | 101326L | Deflector, Muffler | 56 | 123102X | Bracket, Clutch |
10 | 71070510 | Hex Hd. Cap Screw 5/16-18 x 5/8 | 57 | 110437X | Rod, Brake |
11 | STD551131 | Washer. Lock 5/16 | 58 | 106888X | Spring, Rod. Brake |
12 | 121218X | Keeper, Belt, Engine | 59 | 73350600 | Nut Jam 3/8-16 |
13 | 73220500 | Nut, Hex 5/16 x 18 | 60 | 19131316 | Washer 13/32 x 13/16 x 16 Ga |
14 | 17490620 | Screw, Hex Washer Thd. Rolling 3/8 x 16 x 1-1/4 | 61 | 125638X | Rod, Brake, Parking |
15 | STD551125 | Washer, Lock, Hvy. Helical Spring | 62 | 124236X | Cap Plunger |
16 | 120897X | Transaxle, Foote-Dana, 5 Speed, Model No. 4360-6 | 63 | 122424X | Shaft. Foot Pedal |
17 | STD523727 | Bolt, Hex 3/8-16 x 2 3/4 | 64 | 8883R | Cover Pedal |
18 | STD541437 | Nut, Crownlock 3/8-16 | 65 | 121749X | Washer 25/32 x 1-1/4 x 16 Ga |
19 | 73680500 | Nut, Crownlock 5/16-18 | 66 | STD571810 | Pin, Roll, 3/16 x 1 |
20 | 123666X | Pulley, Transaxle | 67 | 120183X | Bearing, Nylon |
21 | 12000028 | Ring, Retainer | 68 | 123583X | Key, Square, 2.5 х.1845/.1865 |
22 | 109167X | Bracket Transaxle | 69 | 13280324 | Nipple, Pipe 3/8 NPT 3" |
23 | STD523710 | Bolt, Hex 3/8-16 x 1 | 70 | 59192 | Cap, Valve |
24 | 17490512 | Screw, Hex Washer Thread Rolling 5/16-18 x 3/4 | 71 | 65139 | Stem, Valve |
25 | 108171X | Support, Battery | 72 | 123969X | Tire, Rear |
26 | 123662X | Keeper. Belt, L.H. | 73 | 106108X | Rim Assembly, 8", Rear |
27 | 4921H | Retainer, Spring | 74 | 109502X | Spacer |
28 | 106190X | Clamp | 75 | 736800600 | Locknut, Hex, w/washer Insert 3/8-16 |
29 | STD523107 | Bolt, Hex 5/16-18 x 3/4 | 76 | 12000001 | E-Ring |
30 | STD541437 | Nut, Crownlock 3/8 - 16 | 77 | 121520X | Strap. Torque, Transaxle |
31 | 123770X | Strap, Locator | 78 | STD533707 | Bolt, Carriage 3/8-16 x 3/4 |
32 | 123663X | Keeper, Belt, R.H. | 79 | 110422X | Spring Brake |
33 | STD523707 | Retainer Belt | 80 | 105706X | Bearing |
34 | 121748X | Washer 25/32 x 1-5/8 x 16 Ga. | 81 | 123205X | Screw Spider Lock No. 8-18 x 1/2 ABTPS |
35 | 106933X | Knob, Shift | 82 | 17030808 | Screw Spider Lock No. 8-18 x 1/2 ABTPS |
36 | 124461X | Rod, Shift | 83 | 105700X | Spring |
37 | 71040412 | Bolt Hex 1/4-28 x 3/4 | 84 | 106919X | Plate, Shift |
38 | 105701X | Washer Shift Plate | 85 | 19091210 | Washer, Lock, Ext. Tooth 3/8 |
39 | STD561210 | Cotter Pin, 1/8 x 1 | 86 | 11050600 | Tube, Tire (Not furnished with tractor) |
40 | 19151216 | Washer 15/32 x 3/4 x 16 Ga. | 87 | 7152J | Spark Arrester |
41 | 104777X | Retainer, Belt | 88 | 121851X | Washer 9/32 x 3/4 x 10 Ga. |
42 | 17490612 | Screw, Hex Washer Thd. Rolling 3/8 16 x 3/4 | 89 | STD551062 | Washer 21/32 x 1 x 16 Ga. |
43 | 19131312 | Washer 13/32 x 13/16 x 12 Ga. | 90 | STD523727 | Bolt, Hex 3/8 x 16 x 2-3/4 |
44 | 105730X | Keeper, Belt, Engine | 91 | 104757X | Cap, Hub |
45 | 109070X | Retainer Belt | 92 | STD551025 | Washer 9/32 x 5/8 x 16 Ga. |
46 | 4470J | Spacer | 93 | 2751R | Clip, Fuel Line |
47 | 123674X | Idler, Flat | 94 | STD522510 | Bolt, Hex Fin 1/4 x 20 UNC x 1 |
95 | 13290300 | Oil Drain Plug | |||
96 | 126685X | Decal, 12 HP, Craftsman, Engine |
Repair Parts - Steering Assembly
This section lists the part numbers for the steering assembly components of the 12 HP 38" Riding Lawn Tractor.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 123042X012 | Dash | 36 | 124033X | Shaft, Pitman |
2 | 74180512 | Screw Truss Hd. 5/16-18 x 3/4 | 37 | 105663X | Support Saddle, Rear |
3 | 73510500 | Nut Keps 5/16-18 | 38 | 105664X | Support Saddle. Front |
4 | 109816X | Nyliner, Snap In | 39 | 74761060 | Bolt Hex 5/8-11 x 3-3/4 |
5 | 124434X | Control Throttle | 40 | 105669X | Axle Front |
6 | STD522510 | Screw, Hex Thread Cut 1/4 x 20 x 5/8 | 41 | 110438X | Spacer. Bearing. Front Axle |
7 | 126684X | Washer 5/8 x 1/4 x 16 Ga. | 42 | 73901000 | Nut Lock. Flange 5/8-11 |
8 | 124417X | Boot, Steering Shaft | 43 | 17490508 | Screw Hex Washer Thread Roling 5/16-18 x 1/2 Type TT |
9 | 124465X014 | Saddle | 44 | 124037X | Gear, Pinior |
10 | 17490608 | Screw Hex Washer Hd. Thread Rolling 3/8-16 x 12 | 45 | 3366R | Bearing |
11 | 2751R | Clip Insulated | 46 | 105715X | Rod - The |
12 | 125879X | Decal Steering Wheel Cap | 47 | 120754X | Bushing |
13 | 100710L | Insert Steering Wheel | 48 | 19131416 | Washer 13/32 x 7/8 x 16 Ga |
14 | STD541350 | Nut Hex Jam Lock 1/2-20 | 49 | 76020412 | Pin Cotter 1/8 x 3/4 |
15 | 100712K | Washer 2-1/4 | 50 | STD551137 | Washer Lock 3/8 |
16 | 100713N | Wheel Steering | 51 | 73610600 | Nut, Fin Hex 3/8 x 24 UNF |
17 | 100711L | Adapter Steering Wheel | 52 | 124032X | Link - Drag |
18 | STD551125 | Lockwasher 1/4 | 53 | 105656X | Spindle L.H. |
19 | 71070410 | Screw, Socket Hex 1/4 x 20 x 5/8 | 54 | 105654X | Spindle R.H. |
20 | 124030X | Bumper, Hood | 55 | 278H | Fitting Grease |
21 | 5479J | Plug, Button | 56 | 9040H | Bearing Flange |
22 | STD611005 | Screw Hex Self Tap No 10.16 x 1/2 Type ABTPS | 57 | 106732X | Rim-6 Front Inc. 2 Each Key |
23 | 108456X | Decal Instruction. Operating | 58 | 59192 | Cap Valve |
24 | 124373X | Bushing Steering | 59 | 65139 | Stem Valve |
25 | 124036X | Bracket Steering | 60 | 124157X | Tire, Front |
26 | 17490612 | Screw-Hex Washer Thread Rolling 3/8-16 x 3/4 Type TT | 61 | 121749X | Washer 25/32 x 1-1/4 x 16 Ga |
27 | 6266H | Bearing Thrust | 63 | 59904 | Tube Front (Not furnished with tractori |
28 | 124034X | Gear Sector | 64 | 121748X | Washer 25/32 x 1-5/8 x 16 Ga. |
29 | 124035X | Shaft, Support | 65 | STD551231 | Washer. Lock. Int Tooth 5/16 |
30 | 12000029 | Klip Ring | 66 | 110307X | Stop, Mower Clutch |
31 | 57079 | Washer, Hardened | 67 | 19272016 | Washer 2/1/32 x 1-1/4 x 16 Ga |
32 | 124038X | Shaft, Steering, Lower | 68 | 121232X | Cap, Spindle |
33 | 122819X | Screw, Special | |||
34 | 104757X | Cap, Hub |
Repair Parts - Lift Adjustment
This section lists the part numbers for the lift adjustment components of the 12 HP 38" Riding Lawn Tractor.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 124429X | Lever, Clutch, Mower | 32 | 122364X | Plunger |
2 | 106932X | Knob | 33 | 125631X | Grip, Handle |
3 | 106451X | Bolt, Shoulder | 34 | 4939M | Retainer, Srping |
4 | 73680600 | Nut, Crownlock 3/8-16 | 35 | 110029X | Link, Lift |
5 | 106452X | Bracket, Switch, Interlock | 36 | 110447X | Trunnion, Lift |
6 | 19171516 | Washer 17/32 x 15/16 x 16 Ga. | 37 | 110448X | Link, Lift. Adjustable |
7 | 17021008 | Screw, Hex, Tapping, No 10-24 x 1/2 | 38 | 121598X | Arm, Suspension, R.H. |
8 | 106447X | Support, Lever, Clutch | 39 | 105848X | Bolt, Shoulder, 3/8-16 |
9 | 123549X | Cap. Fuel | 40 | 121599X | Arm. Suspension, L.H. |
10 | 109202X | Tank, Fuel | 41 | 106308X | Trunnion. Lift, Lower |
11 | 101335K | Line. Fuel | 42 | STD541050 | Nut Hex 1/2-13 |
12 | 124028X | Grommet | 43 | 9135R | Retainer, Spring |
13 | 123487X | Clamp Hose | 44 | 19171516 | Washer 17/32 x 15/16 x 16 Ga |
14 | 17490612 | Screw, Hex Washer Thd. Rolling 3/8 x 16 x 3/4 | 45 | 4921H | Retainer. Spring |
15 | 19091416 | Washer 9/32 x 7/8 x 16 Ga. | 46 | 105864X | Bracket, Suspension, Rear, R.H |
16 | 122795X | Panel, Dash, L.H | 47 | 106444X | Bracket, Suspension, Rear, L.H |
17 | 121794X | Cover, Access | 48 | STD523707 | Bolt. Hex 3/8 16 x 3/4 |
18 | 124031X012 | Panel, Dash, R H | 49 | 109728X | Bellcrank Assembly |
19 | 19211416 | Washer 21/32 x 7/8 x 16 Ga. | 50 | STD561210 | Pin, Cotter. 1/8 x 3/4 |
20 | STD581062 | E Ring | 51 | 124444X | Rod. Clutch. Primary |
21 | 122365X | Button, Plunger | 52 | 19131410 | Washer 13/32 x 7/8 x 10 Ga |
22 | 122512X | Spring, Compression | 53 | 122514X | Rod Assembly Lever |
23 | 17490412 | Screw, Hex Washer Thd. Rolling 1/4-20 x 3/4 | 54 | 105767X | Pin Groove |
24 | 105736X | Shield, Heat | 55 | 124446X | Spring Extension |
25 | 5320R | Clip, Insulated | 56 | 72140606 | Screw 3/8-16 x 3/4 |
26 | 120183X | Bearing, Nylon | 57 | 108236X | Bracket Switch |
27 | 105839X | Receptacle, 1/4 Turn | 59 | 110739X | Washer Spring |
28 | 105838X | Retainer, 1/4 Turn | 60 | 73980600 | Nut Flangelock 3/8-16 |
29 | STD551025 | Washer 9/32 x 5/8 x 16 Ga. | 61 | 73360700 | Nut. Hex Jam 7/16-20 |
30 | 122507X | Shaft, Lift | 62 | 73710700 | Nut, Crownłock 7/16-20 |
31 | 105751X | Stud, 1/4 Turn |
Repair Parts - 38" Mower
This section lists the part numbers for the 38" mower components of the 12 HP Riding Lawn Tractor.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 106085X | V-Belt | 38 | 121263X | Blade |
2 | 121259X | Housing | 39 | 19132012 | Washer 13/32 x 1-1/4 x 12 Ga |
3 | 8417J | Runner, R.H. | 40 | STD551137 | Washer, Lock 3/8 |
4 | 73680600 | Nut, Crownlock 3/8-16 | 41 | STD623715 | Bolt, Hex, 3/8-24 x 1-1/2 Gr. 5 |
5 | 19111216 | Washer 11/32 x 3/4 x 16 Ga. | 42 | 108250X | Spring, Extension |
6 | 72140505 | Bolt, Carr., 5/16 18 x 5/8 | 43 | 108235X | Rod Clutch, Mower |
7 | 105896X | Bracket, Deflector | 44 | 4921H | Spring Retainer |
8 | 110452X | Pushnut | 45 | 6404J | Spacer 1/2 x 9/16 |
9 | 106734X | Spring, Deflector | 46 | 124066X | Rock Shaft Assembly |
10 | 106735X | Rod Hinge | 47 | 76020616 | Pin, Cotter, 3/16 x 1 |
11 | 106736X | Deflector Shield | 48 | 108247X | Rod, Brake, Primary |
12 | 105814X | Decai, V-Belt Mower Drive | 49 | 72140606 | Bolt, Carr. 3/8-16 x 3/4 |
13 | 105304X | Cap | 50 | 108243X | Bracket, Pivot, R.H. |
14 | 105662X | Link, Parallel | 51 | 108241X | Bracket. Pivot, L.H |
15 | 105744X | Pin Hinge, Front | 52 | 105857X | Bracket, Suspension, Rear, R.H. |
16 | 105872X | Stop, Link | 53 | 108673X | Bracket, Suspension, Rear, L.H |
17 | 109835X | Pin Hinge, Rear | 54 | 106578X | Brake Assembly |
18 | STD523707 | Bolt 3/8-16 x 3/4 | 55 | 106463X | Rod. Brake, Secondary, L.H. |
19 | 73680500 | Nut, Crownlock 5/16-18 | 56 | 108249X | Rod, Brake, Secondary, R.H. |
20 | 109598X | Bracket, Lift, R.H | 57 | 106456X | Bracket, Brake, Pivot |
21 | 109597X | Bracket, Lift. L.H | 58 | 100672K | Spacer, Brake |
22 | STD533107 | Bolt, Carr. 5/16-18 x 3/4 | 59 | 100673L | Spacer, Brake |
23 | 3713J | Decal, Instruction Caution | 60 | 19131614 | Washer 13/32 x 1 x 14 Ga. |
24 | 109503X | Support, Arm | 61 | 74760688 | Bolt, 3/8-16 x 5-1/2 |
25 | 109504X | Stop. Deck, Front | 62 | 7631J | Runner, L.H. |
26 | 123204X | Decal Safety Standard Not Serviced | 63 | 19111016 | Washer 11/32 x 5/8 x 16 Ga. |
27 | 74760632 | Bolt, 3/8-16 x 1-1/4 | 64 | 72140610 | Bolt 3/8-16 x 2 |
28 | 123553X | Arm, Idler | 65 | 121343X | Decal Warning |
29 | 106902X | Spacer Retainer | 66 | 122314X | Spacer |
30 | 121316X | Pulley Idler | 67 | STD560907 | Pin, Cotter, 3/32 x 1/2 |
31 | 106513X | Washer, Wear, 1/16 | 68 | 72110506 | Bolt. Carriage 5/16-18 x 3/4 |
32 | 102669X | Keeper. Belt | 69 | 74760412 | Bolt Hex 1/4-20 x 3/4 |
33 | 121687X | Mandrel Assembly | 70 | 109893X | Washer, Special |
34 | 100668L | Plate, Support Mandrel | 71 | 73680400 | Nut, Crownlock 1/4-20 |
35 | 17490614 | Screw, Hex Washer Hd. 3/8 x 16 x 7/8 | 72 | 110445X | Plate, Support, Mandrel, L.H. |
36 | 17490620 | Screw, Hex Washer Hd. 3/8 x 16 x 1-1/4 | 73 | STD551037 | Washer 13/32 x 13/16 x 16 Ga. |
37 | 122215X | Mower Assembly, Complete |
Repair Parts - Transaxle Foote - Model Number 4360-6
This section lists the part numbers for the transaxle components of the 12 HP 38" Riding Lawn Tractor.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 120458X | Housing, Upper | 39 | 120471X | Shaft, Idler |
2 | 2274J | Screw, Tapping, 1/4-20 x .734 Lg. | 40 | 120472X | Spacer, .635 x .875 x .755 |
3 | 34- 68003 | Ball, Detent | 41 | 105928X | Sprocket, 9T |
4 | 105904X | Spring, Detent | 42 | 110084X | Gear, Bevel, 42T. |
5 | 105905X | Screw, Set | 43 | 108983X | Washer, Plain, 758 x 1.12 x .010 |
6 | 120460X | Ass'y., Shifter | 43 | 105930X | Washer, Plain, 758 x 1.12 x .015 |
7 | 120461X | O-Ring | 43 | 105931X | Washer, Plain, 758 x 1.12 x .020 |
8 | 120462X | Washer, Plain, 505 x .942 x .006 | 43 | 105932X | Washer, Plain, 758 x 1.12 x .025 |
8 | 120463X | Washer. Plain, 505 x .942 x .010 | 43 | 3417J | Washer, Plain, 758 x 1.25 x .020 |
8 | 120464X | Washer. Plain, .505 x .942 x .015 | 43 | 106097X | Washer, Plain. 758 x 1.25 x .025 |
8 | 120465X | Washer. Plain, 505 x .942 x .020 | 43 | 2264J | Washer, Plain, 758 x 1.25 x .031 |
8 | 120466X | Washer. Plain, 505 x .942 x .026 | 43 | 106098X | Washer, Plain, 758 x 1.25 x .035 |
8 | 83818 | Washer, Plain, 505 x .942 x .030 | 43 | 2265J | Washer, Plain, 758 x 1.25 x .040 |
8 | 120467X | Washer. Plain, .505 x .942 x .040 | 43 | 106586X | Washer. Plain, 758 x 1.25 x .045 |
9 | 2286J | Ring. Retaining | 43 | 106587X | Washer. Plain, 758 x 1.25 x .050 |
10 | 2267J | Ring. Retaining | 43 | 106588X | Washer, Plain, 758 x 1.25 x .055 |
11 | 3413J | Washer. Plain, 632 x 1.00 x .010 | 43 | 2263J | Washer, Plain, 758 x 1.25 x .062 |
11 | 2233J | Washer. Plain. 632 x 1.00 x .020 | 44 | 120473X | Shaft, Drive |
11 | 2232J | Washer. Plain, 632 x 1.00 x .026 | 45 | 105933X | Gear, Spur. 12T. |
11 | 2231J | Washer. Plain, 632 x 1.00 x 031 | 46 | 120407X | Gear, Spur. 20T. |
11 | 2230J | Washer. Plain, 632 x 1.00 x .036 | 47 | 106589X | Gear, Spur. 25T. |
11 | 2229J | Washer. Plain, 632 x 1.00 x .041 | 48 | 120408X | Gear, Spur. 28T. |
11 | 2228J | Washer. Plain, 632 x 1.00 x .046 | 49 | 105937X | Gear, Spur. 317. |
11 | 2227J | Washer. Plain, 632 x 1.00 x .050 | 50 | 105936X | Spacer, 781 x 1.00 x .375 |
11 | 2226J | Washer. Plain, 632 x 1.00 x .060 | 51 | 2226J | Washer, Plain, .632 x 1.00 x .060 |
11 | 105906X | Washer. Plain, 632 x 1.00 x .082 | 52 | 2272J | Seal, Felt |
12 | 6725J | O-Ring | 53 | 2263J | Washer, Plain, 758 x 1.25 x .062 |
13 | 120415X | Washer. Plain, 632 x 1.38 x .046 | 54 | 120474X | Axle, L.H. |
14 | 2257J | Key. Woodruff, #9 | 55 | 110081X | Gear. Miter. 15T. |
15 | 110077X | Ass'y., Kit, Input Shaft | 56 | 105941X | Ring, Retaining |
16 | 110078X | Pinion. Bevel. 14T. | 57 | 110071X | Gear, Spur. 32T. |
17 | 105909X | Ring. Retaining | 58 | 120952X | Shatt, Cross |
18 | 105910X | Chain, 24 Pitches | 59 | 110082X | Gear, Miter, 15T. |
19 | 105911X | Bearing. Flange | 60 | 120475X | Axle. R.H. |
20 | 108976X | Gear, Spur, 14T. | 61 | 120476X | Housing. Lower |
21 | 105913X | Collar, Clutch | 62 | 120961X | Puck, Friction |
22 | 120468X | Key, Clutch | 63 | 64260 | Disc. Brake |
23 | 2242J | Key. Woodruff, #3 | 64 | 108989X | Spacer |
24 | 120469X | Shaft, Intermediate | 65 | 120953X | Ass'y, Jaw, Brake |
25 | 2244J | Key. Woodruff #61 | 66 | 120954X | Pin. Dowel |
26 | 105916X | Ring. Retaining | 67 | 120955X | Screw. Tapping, 5/16 18 x 2.25 |
27 | 120470X | Sprocket. 18T. | 68 | 108992X | Lever. Actuating |
28 | 110070X | Spacer | 69 | 108996X | Washer, Plain. 321 x 1.00 x .055 |
29 | 108977X | Gear, Spur, 37T. | 70 | 120956X | Bracket. Anti-Rotation |
30 | 120405X | Gear, Spur, 30T. | 71 | 73810500 | Nut. Lock 5/16-24 |
31 | 108980X | Gear, Spur, 25T. | 72 | 106596X | Screw, Tapping, 5/16 18 x 1.44 Lg. |
32 | 120406X | Gear, Spur, 22T. | 73 | 120993X | Washer, Plain, 343 x .81 x .059 |
33 | 108455X | Gear, Spur, 19T | 74 | 120951X | Puck, Friction |
34 | 105923X | Spacer, 1.13 x 1.50 x .375 | 75 | 120416X | Grease |
35 | 105925X | Washer, Plain, 640 x 1.37 x .061 | |||
36 | 2232J | Washer. Plain, 632 x 1.00 x .026 | |||
37 | 108978X | Spacer, 630 x 1.00 x169 | |||
38 | 110079X | Ass'y., Gear. Combo., 12T. & 35T. |
Repair Parts - Engine Briggs & Stratton
This section lists the part numbers for the engine components of the 12 HP 38" Riding Lawn Tractor, Briggs & Stratton Model Number 281707, Type Number 0412-01.
KEY NO. | PART NO. | DESCRIPTION | KEY NO. | PART NO. | DESCRIPTION |
---|---|---|---|---|---|
1 | 93535 | Screw-Sem | 31 | 394698 | Carburetor Overhaul Kit |
2 | Motor-Starting (12 Volt) See Chart on Bottom of Page for Replacement Parts. | 32 | 270382 | Washer-Choke Shaft | |
3 | 93984 | Screw-Sem | 33 | 91920 | Screw-Machine, Fill. Hd. 8-32 x 5/8" |
4 | 490324 | Cover-Starter (Includes Mounting Screws) | 34 | 222010 | Valve-Choke |
5 | 212706 | Knob-Air Cleaner | 35 | 26157 | Spring-Throttle Adjustment |
6 | 231532 | Nut-Air Cleaner Mtg. | 36 | 93043 | Pin-Throttle Stop |
7 | 94249 | Washer-Air Cleaner | 37 | 299740 | † Nozzle-Carburetor |
8 | 223700 | Cover-Air Cleaner | 38 | 292681 | † Valve Assembly-Carburetor Idle |
9 | 94248 | Stud-Air Cleaner | 39 | 93499 | Screw-Throttle and Choke Valve Mtg. Sem |
10 | 491519 | Cartridge-Air Cleaner | 40 | 211712 | Stop-Throttle |
11 | 491877 | Body-Air Cleaner | 41 | 261116 | Spring-Choke Return |
12 | 94018 | Screw-Air Cleaner Sem | 42 | 390684 | Shaft and Lever-Choke |
13 | 93805 | Screw-Sem | 43 | 211960 | Venturi Carburetor |
14 | 222562 | Screen-Flush Rotating | 44 | 221997 | † Plug-Weich |
15 | 280848 | Spacer | 45 | 490473 | Body Assembly-Carburetor |
16 | 92284 | Nut-Hex. | 46 | 271853 | Washer-Throttle Shaft Seal (Foam) |
17 | 220865 | Washer-Spring | 47 | 398970 | Seal-Throttle Shaft |
18 | 222561 | Screw-Sem | 48 | 491006 | Shaft and Lever-Throttle |
19 | 393295 | Stator-Alternator (Tri-Circuit) | 49 | 270511 | † Gasket-Float Bowl |
20 | 93621 | Link-Choke | 50 | 299707 | Float-Carburetor |
21 | 261610 | Link-Choke | 51 | 222433 | † Screw-Nozzle |
22 | 394890 | Regulator-Alternator (9 Amp.) | 52 | 231323 | Bowl-Float |
23 | 93559 | Screw-Regulator | 53 | 221995 | † Pin-Float Hinge |
24 | 394358 | Filter-Fuel (In Fuel Line) | 54 | 230896 | Carburetor Assembly |
25 | 93053 | Clamp-Fuel Pipe | 55 | 491031 | † Valve-Fuel Inlet |
26 | 393815 | Line-Fuel (11" long) (Cut to Suit ) | 56 | 394681 | Bracket-Carburetor |
27 | 67218 | Connector-Fuel Pipe | 57 | 222311 | Valve-Needle |
28 | 93572 | Screw-Carburetor | 58 | 396568 | † Washer-Float Bowl |
29 | 270872 | Gasket-Carburetor Mounting | 59 | 222014 | Washer-Float Bowl |
30 | 93357 | Screw-Carburetor Mtg. |
Key Number Summary:
Key Number | Starter Motor Mfr. and Motor Model Number | Motor and Drive Ass'y. | Brush Ass'y. | Thru Bolt Ass'y. | 64 Brush Ass'y. | 70 Armature Ass'y. | 63 End Cap Ass'y. | 65 Housing Ass'y |
---|---|---|---|---|---|---|---|---|
Briggs & Stratton | Housing Length | |||||||
12V | 3-21/32" | 394805 | 94003 | 395538-490421** | 390837 | 394857 | 395537* | 393825 |
* Includes Brush Set
** Includes #398003 Clutch Assembly (Key No. 67), #280104 Gear (Key No. 68), #490467 Retainer and Pin (Key No. 60), #94288 Roll Pin (Key No. 69)
* Included in Gasket Set-Part No. 490525
** Included in Carburetor Overhaul Kit-Part No. 394698
Attachments That Add to the Usefulness of Your Craftsman Lawn Tractor
Sears offers a wide variety of attachments that fit your tractor. Many of these are listed below with brief explanations of how they can help you. This list was current at the time of publication; however, it may change in future years - more attachments may be added, changes (including changes in the stock number) may be made in these attachments, or some may no longer be available.
Most of these attachments do not require additional hitches or conversion kits (those that do are indicated) and are designed for easy attaching and detaching. You may order these attachments at most Sears retail stores, catalog sales offices, and through the catalog.
PERMANEX BAGGER
Lets you collect grass clippings and leaves for a healthier neater-looking lawn. Two Permanex containers hold 30-gallon plastic bags. Stock number 71-24940.
LAWN SWEEPERS
Let you collect grass clippings and leaves.
- 71-24030: 30-in., 9.0 cu. ft.
- 71-24032: 32-in., 10.0 cu. ft.
- 71-24033 High-Performance: 32 in., 11.5 cu. ft.
- 71-24038: 38-in., 12.5 cu. ft.
LAWN VACS
For powerful collections of heavy grass clippings and leaves. Wand attachment to pick up debris in hard-to-reach places.
- 71-2452: 3HP, 12 bu., 71-26471 chute
CARTS
Make hauling easy.
- 71-24353: 4 cu. ft., 400 lb. Dump cart
- 71-24354: 10 cu. ft., 1,000 lb. Hauling cart
- 71-24355: 10 cu. ft., 1,000 lb. Dump cart
- 71-24356: 14 cu. ft., 1,250 lb. Dump cart
ROLLER
For smoother lawn surface. 36-inch wide, 18 inch diameter water-tight drum holds up to 390 lb. of weight. Rounded edges prevent harm to turf. Adjustable scraper automatically cleans drum. Stock number 71-24084.
SPREADER/SEEDERS
Make seeding, fertilizing, and weed killing easy. Broadcast spreaders are also useful for granular de-icers and sand.
- 71-24194: Drop type, 36 inch. 12 in. semi-pneumatic wheels. 100 lb. capacity steel hopper.
- 71-24394: Broadcasts over a 5 to 8 foot swath. 70 lb. capacity steel hopper. Noncorrosive spreading spinner, nylon gear box, stainless steel shaft.
- 71-24395: Broadcasts 8 to 10 foot swath. 160 lb. capacity. No-rust polypropylene hopper and impeller. Vinyl hopper cover.
CORING AERATOR
Takes small plugs out of soil to allow moisture and nutrients to reach grass roots. 36-inch swath. 24 hardened steel coring tips. 150 lb. capacity weight tray. Stock number 71-24351.
AERATOR
Promotes deep root growth for a healthy lawn. Tapered 2.5" steel spikes mounted on 10-in. diameter discs puncture holes in soil at close intervals to let moisture soak it. Steel weight tray for increased penetration. Stock number 71-2435.
DETHATCHER
Loosens and flips thatch and matted leaves to lawn surface for easy pick up. Twenty spring tine teeth. Useful to prepare bare areas for reseeding. 40 inch rear mount: Stock number 71-24313. 38 inch front mount: Stock number 71-24301.
SPRAYERS
Use 12-volt DC electric motor that connects to the tractor battery or other 12-volt source. Includes booms for automatic spraying when pulling, and hand held wand for spot spraying. Wand has adjustable spray pattern. For applying herbicides, insecticides, fungicides, and liquid fertilizers.
- 71-2458: 50 psi maximum pressure with 12 foot wand length. Sprays up to 25 feet with wand.
- 71-24398: 25 psi maximum pressure with 10 foot wand length. Sprays up to 18 feet with wand.
SNOW BLADE
For snow removal only. 14 inch high, 42 inch wide blade clears 38 inch path when angled left or right. Raises, lowers with side lever. Adjustable skids: replaceable, reversible scraper bar. (Use with tire chains, wheel weights, or rear drawbar weight). Stock number 71-24407.
SNOWTHROWER
Has 40-inch swath. Drum-type auger handles powdery and wet/heavy snow. Mounts easily with simple pin arrangement. Discharge chute adjusts to 210 degree arc from tractor seat. 6-inch diameter spout discharges snow 10 to 50 ft. Lift controlled at tractor seat. (Use with tire chains, wheel weights, or rear drawbar weight). Stock No. 71-24072.
TIRE CHAINS
Are heavy duty; closely spaced extra-large cross links give smooth ride, outstanding traction. Stock No. 71-24952.
WHEEL WEIGHTS
For rear wheels provide needed traction for snow removal or dozing heavy materials. In pairs. Stock No. 71-24434 (30 lb. each)
TRACTOR CAB
Has heavy duty vinyl fabric over tubular steel frame, ABS plastic top; clear plastic windshield offers 360 degree visability. Hinged metal frame doors with catch. Keeps operator warm and dry. Remove vinyl and windshield for use as sun protector in summer. Stock No. 71-24171.
Optional accessories for tractor cab: tinted/tempered solid safety glass windshied with hand operated wiper (Stock No. 71-26168); 12-volt amber caution light for mounting on cab top (Stock No. 71-26169).
TRACTOR COVER
Protects tractor from weather. Made of Evolution 3 fabric (water-repellent, extremely breathable, light weight, soft, non-abrasive, pliable in all temperatures, durable, stain-tear-puncture resistant, will not shrink or stretch). Stock No. 71-24601.