18 mag 2021 — Sonic 4000's ± 12 V input offset capability extends the input voltage range of the probe. The input capacitance of < 0.6 pF parallel 2 MΩ between probe tip and ...
2 Sonic 4000 tasheet About Sonic 4000 The Sonic 4000 active probe offers best-in-class performance and is easy to use to make in-circuit measurements. With the Sonic 4000's DC to > 4 GHz bandwidth, high input impedance, low noise and ± 8 V dynamic range makes it the ideal probe to use with any oscilloscope or other
EN Probing Solutions. Made in Germany. SONIC®4000 Robust Active Probe for Troubleshooting >4GHz, ±20V Datasheet Sonic 4000® Datasheet About Sonic 4000 The Sonic 4000 active probe offers best-in-class performance and is easy to use to make in-circuit measurements.With the Sonic 4000's DC to >4GHz bandwidth, high input impedance, low noise and ±8V dynamic range makes it the ideal probe to use with any oscilloscope or other 50 measurement system. Sonic 4000's ±12V input offset capability extends the input voltage range of the probe.The input capacitance of <0.6pF parallel 2M between probe tip and probe reference (1M to the oscilloscope ground) provides the highest impedance in its class to allow the probing of sensitive circuits without adversely loading the circuit under test. The high impedance probe tip reference connection is a key feature of the Sonic 4000.Unlike traditional single-ended probes, with their probe tip reference connected to earth ground that can damage the customer's circuit if it is accidentally connected to any non-ground test point, the probe tip reference impedance to earth ground is 1M.This feature allows for safe in-circuit browsing of an energized circuit without the possibility for shorting the probe tip reference connection directly to earth ground. Sonic 4000 Input Loading Schematic The Sonic 4000 active probe uses a PMK custom high speed FET input amplifier with active cladding wave compensation to provide a superior high frequency response as well as a low noise and low distortion to accurately measure the customer signals. 2 Specifications Order Number Electrical Specifications Attenuation Ratio * Bandwidth (-3dB) * Dynamic Range * DC Offset Input Voltage DC (max.) * Input Impedance ² Output Impedance MMeecchhaannicicaal lSSppeeccifiifcicaatitoionnss Weight (probe only) Cable Length Probe Input Sockets Output Connector ³ EEnnvvirioronnmmeenntatal lSSppeeccifiifcicaatitoionnss Altitude Temperature Range operating non-operating operating non-operating Maximum Relative Humidity operating non-operating Sonic 4000 884-000-000 10:1 (±2% at DC) > 4GHz ±8V ±12V ±20V ¹ 2 M || 0.6 pF 50 Sonic 4000® Datasheet 107g 1.3m 0.64mm square / 0.8mm round BNC (male) up to 2000m up to 15000m 0°C to +45°C -40°C to +71°C 80% relative humidity for temperatures up to +31°C, decreasing linearly to 40% at +45°C 95% relative humidity for temperatures up to +40°C This product comes with 2 years warranty. Specifications that are not marked with (*) as guaranteed are typical. ¹ ESD protected, IEC 61000-4-2 Contact Discharge Level 2, IEC 61000-4-2 Air Discharge Level 3. See frequency derating on page 4. 3 Sonic 4000® Datasheet Input Impedance referred to Probe Ground The input impedance of the probe decreases as the frequency of the applied signal increases. The charts given here are valid for no measurement category, not in CAT II, III, IV (¹). |Z||Z|[/OOhhmm] Input Impedance reffered to Probe Ground 10M 1M 100K 10K 1K 100 1 10 100 1K 10K 100K 1M 10M 100M 1G Frequency [Hz] Maximum Input Voltage The Sonic 4000 active probe is protected against electro-static-discharge voltage (ESD). The charts given here are valid for no measurement category, not in CAT II, III, IV (¹). InIpnuptuVt Vooltlataggeevvss. .FFrreeqquueennccyySSoOnNicIC/ 4S0o0n0icRRFF Input Voltage vs.10F0requency SONIC 4000 RF 100 20 20 10 8 10 8 Peak Voltage [V] PeaPkeakVoVlolttaagge [eV] [V] 1 1M 1 4G 1M 10M 100M 1G 10G 10M 100M Frequency [Hz] 1G FreFqreuque1e0nnGccyy[Hz[]Hz] Dynamic Measurement Range Maximum Input Voltage Dynamic Measurement Range Maximum Input Voltage 4 5 890-100-150 self-adhesive Cu-pads x10 (2 cm x 2 cm) 891-010-810 2.54 mm adapter x10 891-025-810 2.54 mm adapter x25 891-010-814 PCB adapter x10 891-025-814 PCB adapter x 25 890-400-812 Ground blade 890-400-811 Z-ground 890-400-813 Ground leaf 890-800-001 Spring tip x5 890-800-000 Solid tip x5 890-500-800 L-In adapter 890-502-130 Pair QFP IC-clips 13 mm (long) up to zu 0.5 mm (1 pair: yellow, green) 890-502-000 Pair QFP IC-clips (short) up to 0.5 mm (1 pair: yellow, green) P25-0 /-2 Pico HookTM (black, red) 890-720-840 Y-adapter to 0.8 mm sockets Power Supplies - PS-02 (2 channel with USB) 889-09V-PS2 - PS-02-L (2 channel with LAN and USB) 889-09V-PS2-L - PS-03 (4 channel with USB) 889-09V-PS3 - PS-03-L (4 channel with LAN and USB) 889-09V-PS3-L - AP-01 (battery pack, 1 channel) 889-09V-AP01 890-880-105 2-Footer (black) 890-020-916 Marker bands 4 x 4 colors 890-400-808 Ground lead 7 cm 890-400-809 Ground lead 13 cm 890-400-803 Ground lead 90° 5 cm 890-400-804 Ground lead 90° 10 cm The parts supplied are ,,highlighted", see also "Scope of Delivery". A power supply with remote control capabilities or a battery pack for portable use are optional. Probe Accessories Sonic 4000® Datasheet Sonic 4000® Datasheet Scope of Delivery Accessories delivered with each probe are ,,highlighted" in the graphical overview. Item Qty Item Qty Probe Sonic 4000 Calibration Certificate Instruction Manual Case 2-Footer (black) 2.54mm Adapter Sonic Ground Blade Ground Lead 7cm Ground Lead 13 cm Ground Lead 90° 5 cm Ground Lead 90° 10 cm 1 L-In Adapter 1 1 Pair PicohooksTM (black & red) 1 1 Pair QFP IC-Clips (short, yellow & green) 1 1 Pair SMD Test Grabbers (black & red) 1 1 PCB Adapter 5 2 Self adhesive Cu Pad (2 cm x 2 cm) 2 1 Set Marker bands (4 x 4 Colors) 1 1 Solid Tip 3 1 Spring Tip 3 1 Y-Lead Adapter to 0.8 mm sockets 1 1 Z-Ground 1 Ordering Information Product Sonic 4000 Probe Power Supplies Order Number 889-09V-PS2 889-09V-PS2-L 889-09V-PS3 889-09V-PS3-L Product 2ch power supply PS-02 with USB 2ch power supply PS-02-L with LAN and USB 4ch power supply PS-03 with USB 4ch power supply PS-03-L with LAN and USB Order number 884-000-000 Order Number 889-09V-AP01 890-520-900 890-520-915 - Product 1ch Battery pack AP-01 Power supply cable (0.5 m) 1 Power supply cable (1.5 m) - ¹ The power supply cable (0.5m), is included as standard with all power supplies. 6 Notes Sonic 4000® Datasheet 7 Manufacturer PMK Mess- und Kommunikationstechnik GmbH Koenigsteinerstrasse 98 65812 Bad Soden am Taunus, Germany Phone: +49 (0) 6196 5927 - 930 Fax: +49 (0) 6196 5927 - 939 Internet: www.pmk.de E-Mail: sales@pmk.de Copyright © 2022 PMK - All rights reserved. Information in this publication supersedes that in all previously published material. Specifications are subject to change without notice. D84-SONIC4000-000 Revision 02.2022Adobe PDF Library 15.0 Adobe InDesign 16.3 (Windows)