TECNO MOBILE LIMITED L6502S Mobile Phone 2ADYY-L6502S 2ADYYL6502S l6502s
1 Cover Page JianYan Testing Group Shenzhen Co., Ltd. Report No: JYTSZB-R12-2100569 FCC REPORT (Bluetooth) Applicant: TECNO MOBILE LIMITED Address of Applicant: FLAT 39 8/F BLOCK D WAH LOK INDUSTRIAL CENTRE 3135 SHAN MEI STREET FOTAN NT Equipment Under Test (EUT) Product Name: Mobile Phone Model No.: L6502S Trade mark: TECNO FCC ID: 2ADYY-L6502S Applicable standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Date of sample receipt: 15 Apr., 2021 Date of Test: 16 Apr., to 07 May, 2021 Date of report issued: 25 May, 2021 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. Authorized Signature: Bruce Zhang Laboratory Manager This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product and does not permit the use of the JYT product certification mark. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. This report may only be reproduced and distributed in full. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Version No. 00 Report No: JYTSZB-R12-2100569 Date 25 May, 2021 Description Original Tested by: Test Engineer Reviewed by: Project Engineer Date: Date: 25 May, 2021 25 May, 2021 JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 2 of 39 Report No: JYTSZB-R12-2100569 3 Contents Page 1 COVER PAGE.............................................................................................................................................................1 2 VERSION.....................................................................................................................................................................2 3 CONTENTS .................................................................................................................................................................3 4 TEST SUMMARY........................................................................................................................................................4 5 GENERAL INFORMATION........................................................................................................................................5 5.1 CLIENT INFORMATION.......................................................................................................................................5 5.2 GENERAL DESCRIPTION OF E.U.T. ...................................................................................................................5 5.3 TEST ENVIRONMENT AND MODE ........................................................................................................................6 5.4 DESCRIPTION OF SUPPORT UNITS ....................................................................................................................6 5.5 MEASUREMENT UNCERTAINTY..........................................................................................................................6 5.6 ADDITIONS TO, DEVIATIONS, OR EXCLUSIONS FROM THE METHOD .......................................................................6 5.7 LABORATORY FACILITY.....................................................................................................................................6 5.8 LABORATORY LOCATION...................................................................................................................................6 5.9 TEST INSTRUMENTS LIST ..................................................................................................................................7 6 TEST RESULTS AND MEASUREMENT DATA ......................................................................................................8 6.1 ANTENNA REQUIREMENT..................................................................................................................................8 6.2 CONDUCTED EMISSIONS ..................................................................................................................................9 6.3 CONDUCTED OUTPUT POWER ........................................................................................................................12 6.4 20DB OCCUPY BANDWIDTH............................................................................................................................13 6.5 CARRIER FREQUENCIES SEPARATION .............................................................................................................14 6.6 HOPPING CHANNEL NUMBER..........................................................................................................................15 6.7 DWELL TIME ..................................................................................................................................................16 6.8 PSEUDORANDOM FREQUENCY HOPPING SEQUENCE........................................................................................17 6.9 BAND EDGE...................................................................................................................................................18 6.9.1 Conducted Emission Method ...........................................................................................................18 6.9.2 Radiated Emission Method ..............................................................................................................19 6.10 SPURIOUS EMISSION....................................................................................................................................32 6.10.1 Conducted Emission Method.......................................................................................................32 6.10.2 Radiated Emission Method..........................................................................................................33 7 TEST SETUP PHOTO .............................................................................................................................................. 38 8 EUT CONSTRUCTIONAL DETAILS ......................................................................................................................39 JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 3 of 39 Report No: JYTSZB-R12-2100569 4 Test Summary Test Items Section in CFR 47 Test Data Result Antenna Requirement 15.203 & 15.247 (b) See Section 6.1 Pass AC Power Line Conducted Emission 15.207 See Section 6.2 Pass Conducted Peak Output Power 15.247 (b)(1) Appendix A BT Pass 20dB Occupied Bandwidth 15.247 (a)(1) Appendix A BT Pass Carrier Frequencies Separation 15.247 (a)(1) Appendix A BT Pass Hopping Channel Number 15.247 (a)(1) Appendix A BT Pass Dwell Time 15.247 (a)(1) Appendix A BT Pass Conducted Band Edge Radiated Band Edge 15.205 & 15.209 Appendix A BT See Section 6.9.2 Pass Pass Conducted Spurious Emission Radiated Spurious Emission 15.247(d) Appendix A BT See Section 6.10.2 Pass Pass Remark: 1. Pass: The EUT complies with the essential requirements in the standard. 2. N/A: Not Applicable. 3. The cable insertion loss used by "RF Output Power" and other conduction measurement items is 0.5dB (provided by the customer). Test Method: ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 4 of 39 Report No: JYTSZB-R12-2100569 5 General Information 5.1 Client Information Applicant: TECNO MOBILE LIMITED Address: Manufacturer: FLAT 39 8/F BLOCK D WAH LOK INDUSTRIAL CENTRE 31-35 SHAN MEI STREET FOTAN NT TECNO MOBILE LIMITED Address: Factory: FLAT 39 8/F BLOCK D WAH LOK INDUSTRIAL CENTRE 31-35 SHAN MEI STREET FOTAN NT SHENZHEN TECNO TECHNOLOGY CO.,LTD. Address: 101, Building 24, Waijing Industrial Park, Fumin Community, Fucheng Street, Longhua District, Shenzhen City, P.R.China 5.2 General Description of E.U.T. Product Name: Mobile Phone Model No.: L6502S Operation Frequency: 2402MHz~2480MHz Transfer rate: 1/2/3 Mbits/s Number of channel: 79 Modulation type: GFSK, /4-DQPSK, 8DPSK Modulation technology: FHSS Antenna Type: Internal Antenna Antenna gain: 1.25 dBi Power supply: Rechargeable Li-Polymer Battery DC3.85V-3900mAh AC adapter: Test Sample Condition: Model: A18A-050100U-US2 Input: AC100-240V, 50/60Hz, 0.2A Output: DC 5.0V, 1000mA The test samples were provided in good working order with no visible defects. Operation Frequency each of channel for GFSK, /4-DQPSK, 8DPSK Channel Frequency Channel Frequency Channel Frequency 0 2402MHz 20 2422MHz 40 2442MHz 1 2403MHz 21 2423MHz 41 2443MHz 2 2404MHz 22 2424MHz 42 2444MHz 3 2405MHz 23 2425MHz 43 2445MHz 4 2406MHz 24 2426MHz 44 2446MHz 5 2407MHz 25 2427MHz 45 2447MHz ... ... ... ... ... ... 15 2417MHz 35 2437MHz 55 2457MHz 16 2418MHz 36 2438MHz 56 2458MHz 17 2419MHz 37 2439MHz 57 2459MHz 18 2420MHz 38 2440MHz 58 2460MHz 19 2421MHz 39 2441MHz 59 2461MHz Remark: Channel 0, 39 &78 selected for GFSK, /4-DQPSK and 8DPSK. Channel 60 61 62 63 64 65 ... 75 76 77 78 Frequency 2462MHz 2463MHz 2464MHz 2465MHz 2466MHz 2467MHz ... 2477MHz 2478MHz 2479MHz 2480MHz JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 5 of 39 Report No: JYTSZB-R12-2100569 5.3 Test environment and mode Operating Environment: Temperature: 24.0 C Humidity: 54 % RH Atmospheric Pressure: 1010 mbar Test Modes: Non-hopping mode: Keep the EUT in continuous transmitting mode with worst case data rate. Hopping mode: Keep the EUT in hopping mode. Remark GFSK (1 Mbps) is the worst case mode. Radiated Emission: The sample was placed 0.8m (below 1GHz)/1.5m (above 1GHz) above the ground plane of 3m chamber*. Measurements in both horizontal and vertical polarities were performed. During the test, each emission was maximized by: having the EUT continuously working, investigated all operating modes, rotated about all 3 axis (X, Y & Z) and considered typical configuration to obtain worst position, manipulating interconnecting cables, rotating the turntable, varying antenna height from 1m to 4m in both horizontal and vertical polarizations. The emissions worst-case are shown in Test Results of the following pages. 5.4 Description of Support Units The EUT has been tested as an independent unit. 5.5 Measurement Uncertainty Parameters Conducted Emission (9kHz ~ 30MHz) Radiated Emission (9kHz ~ 30MHz) Radiated Emission (30MHz ~ 1000MHz) Radiated Emission (1GHz ~ 18GHz) Radiated Emission (18GHz ~ 40GHz) Expanded Uncertainty ±1.60 dB (k=2) ±3.12 dB (k=2) ±4.32 dB (k=2) ±5.16 dB (k=2) ±3.20 dB (k=2) 5.6 Additions to, deviations, or exclusions from the method No 5.7 Laboratory Facility The test facility is recognized, certified, or accredited by the following organizations: FCC - Designation No.: CN1211 JianYan Testing Group Shenzhen Co., Ltd. has been accredited as a testing laboratory by FCC(Federal Communications Commission). The test firm Registration No. is 727551. ISED CAB identifier.: CN0021 The 3m Semi-anechoic chamber of JianYan Testing Group Shenzhen Co., Ltd. has been Registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 10106A-1. A2LA - Registration No.: 4346.01 This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. The test scope can be found as below link: https://portal.a2la.org/scopepdf/4346-01.pdf 5.8 Laboratory Location JianYan Testing Group Shenzhen Co., Ltd. Address: No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Tel: +86-755-23118282, Fax: +86-755-23116366 Email: info@ccis-cb.com, Website: http://www.ccis-cb.com JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 6 of 39 Report No: JYTSZB-R12-2100569 5.9 Test Instruments list Test Equipment 3m SAC BiConiLog Antenna Biconical Antenna Horn Antenna Horn Antenna Horn Antenna EMI Test Software Pre-amplifier Pre-amplifier Spectrum analyzer Spectrum analyzer EMI Test Receiver Spectrum Analyzer Signal Generator Signal Generator RF Switch Unit Test Software Cable Cable Cable DC Power Supply Temperature Humidity Chamber Simulated Station Manufacturer ETS SCHWARZBECK SCHWARZBECK SCHWARZBECK SCHWARZBECK SCHWARZBECK AUDIX HP CD Rohde & Schwarz Rohde & Schwarz Rohde & Schwarz Agilent Rohde & Schwarz R&S MWRFTEST MWRFTEST ZDECL MICRO-COAX SUHNER XinNuoEr HengPu Rohde & Schwarz Model No. 9m*6m*6m VULB9163 VUBA9117 BBHA9120D BBHA9120D BBHA 9170 E3 8447D PAP-1G18 FSP30 FSP40 ESRP7 N9020A SMX SMR20 MW200 MTS8200 Z108-NJ-NJ-81 MFR64639 SUCOFLEX100 WYK-10020K HPGDS-500 CMW500 Serial No. Cal. Date (mm-dd-yy) Cal. Due date (mm-dd-yy) 966 01-19-2021 01-18-2024 497 03-03-2021 03-02-2022 359 06-18-2020 06-17-2021 916 03-03-2021 03-02-2022 1805 06-18-2020 06-17-2021 BBHA9170582 11-18-2020 11-17-2021 Version: 6.110919b 2944A09358 03-03-2021 03-02-2022 11804 03-03-2021 03-02-2022 101454 03-03-2021 03-02-2022 100363 11-18-2020 11-17-2021 101070 03-03-2021 03-02-2022 MY50510123 11-18-2020 11-17-2021 835454/016 03-03-2021 03-02-2022 1008100050 03-03-2021 03-02-2022 N/A N/A N/A Version: 2.0.0.0 1608458 03-03-2021 03-02-2022 K10742-5 03-03-2021 03-02-2022 58193/4PE 03-03-2021 03-02-2022 1409050110020 09-25-2020 09-24-2021 20140828008 11-01-2020 10-31-2021 140493 07-22-2020 07-21-2021 Conducted Emission: Test Equipment EMI Test Receiver Pulse Limiter LISN LISN Cable EMI Test Software Manufacturer Rohde & Schwarz SCHWARZBECK CHASE Rohde & Schwarz HP AUDIX Model No. ESCI OSRAM 2306 MN2050D ESH3-Z5 10503A E3 Serial No. Cal. Date (mm-dd-yy) Cal. Due date (mm-dd-yy) 101189 03-03-2021 03-02-2022 9731 03-03-2021 03-02-2022 1447 03-03-2021 03-02-2022 8438621/010 06-18-2020 06-17-2021 N/A 03-03-2021 03-02-2022 Version: 6.110919b Conducted method: Test Equipment Spectrum Analyzer Vector Signal Generator Analog Signal Generator Power Detector Box Simulated Station RF Control Box PDU Test Software DC Power Supply Manufacturer Keysight Keysight Keysight MWRF-test Rohde & Schwarz MWRF-test MWRF-test MWRF-tes Keysight Model No. N9010B N5182B N5173B MW100-PSB CMW270 MW100-RFCB XY-G10 MTS 8310 E3642A Serial No. Cal. Date (mm-dd-yy) MY60240202 11-27-2020 MY59101009 11-27-2020 MY59100765 11-27-2020 MW201020JYT 11-27-2020 102335 11-27-2020 MW200927JYT N/A N/A N/A Version: 2.0.0.0 MY60296194 11-27-2020 Cal. Due date (mm-dd-yy) 11-26-2021 11-26-2021 11-26-2021 11-26-2021 11-26-2021 N/A N/A 11-26-2021 JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 7 of 39 Report No: JYTSZB-R12-2100569 6 Test results and measurement data 6.1 Antenna Requirement Standard requirement: FCC Part 15 C Section 15.203 & 247(b) 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 15.247(b) (4) requirement: (4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. E.U.T Antenna: The Bluetooth antenna is an Internal antenna which permanently attached, and the best case gain of the antenna is 1.25 dBi. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 8 of 39 Report No: JYTSZB-R12-2100569 6.2 Conducted Emissions Test Requirement: FCC Part 15 C Section 15.207 Test Frequency Range: 150 kHz to 30 MHz Class / Severity: Class B Receiver setup: RBW=9 kHz, VBW=30 kHz, Sweep time=auto Limit: Frequency range (MHz) Limit (dBuV) Quasi-peak 0.15-0.5 66 to 56* 0.5-5 56 5-30 60 * Decreases with the logarithm of the frequency. Average 56 to 46* 46 50 Test setup: Test procedure: Test Instruments: Test mode: Test results: 1. The E.U.T and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm/50uH coupling impedance for the measuring equipment. 2. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm/50uH coupling impedance with 50ohm termination. (Please refer to the block diagram of the test setup and photographs). 3. Both sides of A.C. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10(latest version) on conducted measurement. Refer to section 5.9 for details Hopping mode Pass JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 9 of 39 Measurement Data: Product name: Test by: Test frequency: Test voltage: Mobile Phone Mike 150 kHz ~ 30 MHz AC 120 V/60 Hz Report No: JYTSZB-R12-2100569 Product model: Test mode: Phase: Environment: L6502S BT Tx mode Line Temp: 22.5 Huni: 55% Notes: 1. An initial pre-scan was performed on the line and neutral lines with peak detector. 2. Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. Final Level = Receiver Read level + LISN Factor + Aux Factor + Cable Loss. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 10 of 39 Product name: Test by: Test frequency: Test voltage: Mobile Phone Mike 150 kHz ~ 30 MHz AC 120 V/60 Hz Report No: JYTSZB-R12-2100569 Product model: Test mode: Phase: Environment: L6502S BT Tx mode Neutral Temp: 22.5 Huni: 55% Notes: 1. An initial pre-scan was performed on the line and neutral lines with peak detector. 2. Quasi-Peak and Average measurement were performed at the frequencies with maximized peak emission. 3. Final Level =Receiver Read level + LISN Factor + Aux Factor + Cable Loss. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 11 of 39 Report No: JYTSZB-R12-2100569 6.3 Conducted Output Power Test Requirement: FCC Part 15 C Section 15.247 (b)(1) Receiver setup: Limit: RBW=1MHz, VBW=3MHz, Detector=Peak (If 20dB BW 1 MHz) RBW=2MHz, VBW=6MHz, Detector=Peak (If 20dB BW > 1 MHz and < 3MHz) For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 non-overlapping hopping channels: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band: 0.125 watts. Test setup: Test Instruments: Test mode: Test results: Measurement Data: Refer to section 5.9 for details Non-hopping mode Pass Refer to Appendix A - BT JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 12 of 39 Report No: JYTSZB-R12-2100569 6.4 20dB Occupy Bandwidth Test Requirement: FCC Part 15 C Section 15.247 (a)(1) Receiver setup: DH1: RBW=15 kHz, VBW=47 kHz, detector=Peak 2DH1&3DH: RBW=20 kHz, VBW=62 kHz, detector=Peak Limit: Within authorization band Test setup: Test Instruments: Test mode: Test results: Measurement Data: Refer to section 5.9 for details Non-hopping mode Pass Refer to Appendix A - BT JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 13 of 39 Report No: JYTSZB-R12-2100569 6.5 Carrier Frequencies Separation Test Requirement: FCC Part 15 C Section 15.247 (a)(1) Receiver setup: RBW=300 kHz, VBW=1 MHz, detector=Peak Limit: a) 0.025MHz or the 20dB bandwidth (whichever is greater) b) 0.025MHz or two-thirds of the 20dB bandwidth (whichever is greater) Test setup: Test Instruments: Test mode: Test results: Measurement Data: Refer to section 5.9 for details Hopping mode Pass Refer to Appendix A - BT JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 14 of 39 Report No: JYTSZB-R12-2100569 6.6 Hopping Channel Number Test Requirement: FCC Part 15 C Section 15.247 (a)(1) Receiver setup: RBW=100 kHz, VBW=300 kHz, Center Frequency=2441MHz, Frequency Range: 2400MHz~2483.5MHz, Detector=Peak Limit: 15 channels Test setup: Test Instruments: Test mode: Test results: Measurement Data: Refer to section 5.9 for details Hopping mode Pass Refer to Appendix A - BT JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 15 of 39 6.7 Dwell Time Test Requirement: Receiver setup: Limit: Test setup: Report No: JYTSZB-R12-2100569 FCC Part 15 C Section 15.247 (a)(1) RBW=1 MHz, VBW=1 MHz, Span=0 Hz, Detector=Peak 0.4 Second Test Instruments: Test mode: Test results: Measurement Data: Refer to section 5.9 for details Hopping mode Pass Refer to Appendix A - BT JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 16 of 39 Report No: JYTSZB-R12-2100569 6.8 Pseudorandom Frequency Hopping Sequence Test Requirement: FCC Part 15 C Section 15.247 (a)(1) requirement: Frequency hopping systems shall have hopping channel carrier frequencies separated by a minimum of 25 kHz or the 20 dB bandwidth of the hopping channel, whichever is greater. Alternatively. Frequency hopping systems operating in the 2400-2483.5 MHz band may have hopping channel carrier frequencies that are separated by 25 kHz or two-thirds of the 20 dB bandwidth of the hopping channel, whichever is greater, provided the systems operate with an output power no greater than 125 mW. The system shall hop to channel frequencies that are selected at the system hopping rate from a Pseudorandom ordered list of hopping frequencies. Each frequency must be used equally on the average by each transmitter. The system receivers shall have input bandwidths that match the hopping channel bandwidths of their corresponding transmitters and shall shift frequencies in synchronization with the transmitted signals. EUT Pseudorandom Frequency Hopping Sequence The pseudorandom sequence may be generated in a nine-stage shift register whose 5th and 9th stage outputs are added in a modulo-two addition stage. And the result is fed back to the input of the first stage. The sequence begins with the first ONE of 9 consecutive ONEs; i.e. the shift register is initialized with nine ones. · Number of shift register stages: 9 · Length of pseudo-random sequence: 29 -1 = 511 bits · Longest sequence of zeros: 8 (non-inverted signal) An example of Pseudorandom Frequency Hopping Sequence as follow: Each frequency used equally on the average by each transmitter. The system receivers have input bandwidths that match the hopping channel bandwidths of their corresponding transmitters and shift frequencies in synchronization with the transmitted signals. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 17 of 39 Report No: JYTSZB-R12-2100569 6.9 Band Edge 6.9.1 Conducted Emission Method Test Requirement: FCC Part 15 C Section 15.247 (d) Receiver setup: RBW=100 kHz, VBW=300 kHz, Detector=Peak Limit: In any 100 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. Test setup: Test Instruments: Test mode: Test results: Measurement Data: Refer to section 5.9 for details Non-hopping mode and hopping mode Pass Refer to Appendix A - BT JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 18 of 39 Report No: JYTSZB-R12-2100569 6.9.2 Radiated Emission Method Test Requirement: FCC Part 15 C Section 15.209 and 15.205 Test Frequency Range: 2310 MHz to 2390 MHz and 2483.5 MHz to 2500 MHz Test Distance: 3m Receiver setup: Frequency Above 1GHz Detector Peak RMS RBW 1MHz 1MHz VBW 3MHz 3MHz Remark Peak Value Average Value Limit: Frequency Above 1GHz Limit (dBuV/m @3m) 54.00 74.00 Remark Average Value Peak Value Test setup: Test Procedure: Test Instruments: Test mode: Test results: 1. The EUT was placed on the top of a rotating table 1.5meters above the ground at a 3 meter camber. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. Refer to section 5.9 for details Non-hopping mode Passed JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 19 of 39 GFSK Mode: Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Lowest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S DH1 Tx mode Vertical Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 20 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Lowest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S DH1 Tx mode Horizontal Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 21 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Highest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S DH1 Tx mode Vertical Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 22 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Highest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S DH1 Tx mode Horizontal Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 23 of 39 /4-DQPSK mode Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Lowest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 2DH1 Tx mode Vertical Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 24 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Lowest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 2DH1 Tx mode Horizontal Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 25 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Highest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 2DH1 Tx mode Vertical Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 26 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Highest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 2DH1 Tx mode Horizontal Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 27 of 39 8DPSK mode Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Lowest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 3DH1 Tx mode Vertical Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 28 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Lowest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 3DH1 Tx mode Horizontal Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 29 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Highest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 3DH1 Tx mode Vertical Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 30 of 39 Product Name: Test By: Test Channel: Test Voltage: Mobile Phone Mike Highest channel AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S 3DH1 Tx mode Horizontal Temp: 24 Huni: 57% Remark: 1. Final Level = Receiver Read level + Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 31 of 39 Report No: JYTSZB-R12-2100569 6.10 Spurious Emission 6.10.1 Conducted Emission Method Test Requirement: FCC Part 15 C Section 15.247 (d) Limit: In any 100 kHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. Test setup: Test Instruments: Test mode: Test results: Measurement Data: Refer to section 5.9 for details Non-hopping mode Pass Refer to Appendix A - BT JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 32 of 39 Report No: JYTSZB-R12-2100569 6.10.2 Radiated Emission Method Test Requirement: FCC Part 15 C Section 15.209 Test Frequency Range: 9 kHz to 25 GHz Test Distance: 3m Receiver setup: Frequency Detector RBW VBW Remark 30MHz-1GHz Quasi-peak 120kHz 300kHz Quasi-peak Value Above 1GHz Peak RMS 1MHz 1MHz 3MHz 3MHz Peak Value Average Value Limit: Frequency Limit (dBuV/m @3m) Remark 30MHz-88MHz 40.0 Quasi-peak Value 88MHz-216MHz 43.5 Quasi-peak Value 216MHz-960MHz 46.0 Quasi-peak Value 960MHz-1GHz 54.0 Quasi-peak Value Above 1GHz 54.0 Average Value 74.0 Peak Value Test setup: Below 1GHz Above 1GHz Test Procedure: 1. The EUT was placed on the top of a rotating table 0.8m(below 1GHz) /1.5m(above 1GHz) above the ground at a 3 meter chamber. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 33 of 39 Test Instruments: Test mode: Test results: Remark: Report No: JYTSZB-R12-2100569 tower. 3. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rota table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. Refer to section 5.9 for details Non-hopping mode Pass 1. Pre-scan all kind of the place mode (X-axis, Y-axis, Z-axis), and found the Y-axis is the worst case. 2. 9 kHz to 30 MHz is noise floor and lower than the limit 20dB, so only shows the data of above 30MHz in this report. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 34 of 39 Measurement Data (worst case): Below 1GHz: Product Name: Mobile Phone Test By: Mike Test Frequency: 30 MHz ~ 1 GHz Test Voltage: AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S BT Tx mode Vertical Temp: 24 Huni: 57% Suspected Data List Freq. Reading[d NO. [MHz] BV/m] 1 31.6492 54.00 2 90.7281 45.86 3 169.597 4 1740.059 5 3184.506 6 9779.202 7 54.12 55.18 36.14 28.51 Level [dBV/m] 35.91 26.33 35.27 36.35 22.57 25.32 Factor [dB] -18.09 -19.53 -18.85 -18.83 -13.57 -3.19 Limit [dBV/m] 40.00 43.50 43.50 43.50 46.00 54.00 Margin [dB] 4.09 17.17 8.23 7.15 23.43 28.68 Trace QP QP QP QP QP QP Remark: 1. Final Level = Receiver Read level + Factor Factor = Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. 3. The Aux Factor is a notch filter switch box loss, this item is not used. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 35 of 39 Product Name: Test By: Test Frequency: Test Voltage: Mobile Phone Mike 30 MHz ~ 1 GHz AC 120/60Hz Report No: JYTSZB-R12-2100569 Product Model: Test mode: Polarization: Environment: L6502S BT Tx mode Horizontal Temp: 24 Huni: 57% Suspected Data List Freq. Reading[d NO. [MHz] BV/m] 1 33.4923 32.88 2 90.7281 37.21 3 172.507 4 1883.998 5 3369.744 6 8247.800 5 59.50 58.14 43.71 47.49 Level [dBV/m] 15.21 17.68 40.67 40.45 30.41 42.65 Factor [dB] -17.67 -19.53 -18.83 -17.69 -13.30 -4.84 Limit [dBV/m] 40.00 43.50 43.50 43.50 46.00 46.00 Margin [dB] 24.79 25.82 2.83 3.05 15.59 3.35 Trace QP QP QP QP QP QP Remark: 1. Final Level = Receiver Read level + Factor. Factor = Antenna Factor + Cable Loss Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. 3. The Aux Factor is a notch filter switch box loss, this item is not used. JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 36 of 39 Report No: JYTSZB-R12-2100569 Above 1GHz: Frequency (MHz) 4804.00 4804.00 Read Level (dBuV) 55.67 56.48 Frequency (MHz) 4804.00 4804.00 Read Level (dBuV) 49.52 49.13 Antenna Factor (dB/m) 30.78 30.78 Antenna Factor (dB/m) 30.78 30.78 Test channel: Lowest channel Detector: Peak Value Cable Loss (dB) Aux Factor (dB) Preamp Factor (dB) Level (dBuV/m) 6.80 2.44 41.81 53.88 6.80 2.44 41.81 54.69 Detector: Average Value Cable Loss (dB) Aux Factor (dB) Preamp Factor (dB) Level (dBuV/m) 6.80 2.44 41.81 47.73 6.80 2.44 41.81 47.34 Limit Line (dBuV/m) 74.00 74.00 Limit Line (dBuV/m) 54.00 54.00 Over Limit (dB) -20.12 -19.31 Over Limit (dB) -6.27 -6.66 Polarization Vertical Horizontal Polarization Vertical Horizontal Frequency (MHz) 4882.00 4882.00 Frequency (MHz) 4882.00 4882.00 Read Level (dBuV) 55.78 56.50 Read Level (dBuV) 49.34 49.34 Antenna Factor (dB/m) 30.96 30.96 Antenna Factor (dB/m) 30.96 30.96 Test channel: Middle channel Detector: Peak Value Cable Loss (dB) Aux Factor (dB) Preamp Factor (dB) Level (dBuV/m) 6.86 2.47 41.84 54.23 6.86 2.47 41.84 54.95 Detector: Average Value Cable Loss (dB) Aux Factor (dB) Preamp Factor (dB) Level (dBuV/m) 6.86 2.47 41.84 47.79 6.86 2.47 41.84 47.79 Limit Line (dBuV/m) 74.00 74.00 Limit Line (dBuV/m) 54.00 54.00 Over Limit (dB) -19.77 -19.05 Over Limit (dB) -6.21 -6.21 Polarization Vertical Horizontal Polarization Vertical Horizontal Test channel: Highest channel Detector: Peak Value Frequency (MHz) Read Level (dBuV) Antenna Factor (dB/m) Cable Loss (dB) Aux Factor (dB) Preamp Factor (dB) Level (dBuV/m) Limit Line (dBuV/m) Over Limit (dB) 4960.00 56.13 31.11 6.91 2.49 41.87 54.77 74.00 -19.23 4960.00 56.07 31.11 6.91 2.49 41.87 54.71 74.00 -19.29 Detector: Average Value Frequency (MHz) Read Level (dBuV) Antenna Factor (dB/m) Cable Loss (dB) Aux Factor (dB) Preamp Factor (dB) Level (dBuV/m) Limit Line (dBuV/m) Over Limit (dB) 4960.00 48.88 31.11 6.91 2.49 41.87 47.52 54.00 -6.48 4960.00 48.89 31.11 6.91 2.49 41.87 47.53 54.00 -6.47 Remark: 1. Final Level =Receiver Read level + Antenna Factor + Cable Loss + Aux Factor Preamplifier Factor. 2. The emission levels of other frequencies are lower than the limit 20dB and not show in test report. Polarization Vertical Horizontal Polarization Vertical Horizontal JianYan Testing Group Shenzhen Co., Ltd. No.101, Building 8, Innovation Wisdom Port, No.155 Hongtian Road, Huangpu Community, Xinqiao Street, Bao'an District, Shenzhen, Guangdong, People's Republic of China. Telephone: +86 (0) 755 23118282 Fax: +86 (0) 755 23116366 Project No.: JYTSZE2104060 Page 37 of 39Microsoft Word 2010