Dyeetic D16 Car Jump Starter User Manual

What's in the box

• Dyeetic D16 car jump starter * 1
• Intelligent battery clamps with starter cable * 1
• High-quality type-C charging cable * 1
• User-friendly manual * 1
• Storage bag * 1

Contact: support@dyeetic.com

Specifications

Product diagrams

The product features an LED light (①), a Type-C input port (②), two USB output ports (③ and ④), an LCD screen (⑤), a power button/light button (⑥), and a jump clamp port (⑦).

The LCD screen displays battery power percentage (①), input status (②), output status (③), USB1 output (④), and USB2 output (⑤).

The jump starter includes intelligent battery clamps with a BOOST button. The clamps are color-coded: red for positive and black for negative.

Operation Guide

Charge Your USB Devices

Before use, ensure you have a compatible USB charger (2A or above recommended). It is advised to fully charge the product before first use and every 3 months thereafter to maintain battery lifespan.

1. Plug the charging cable into the jump starter's USB-C input port.
2. Connect the other end to a power source.
3. Press the power button to start charging. Disconnect when charging is complete.

Tip: Avoid charging the jump starter immediately after starting the engine; wait at least 30 minutes.

Recharge the Jump Starter

1. Connect the jump starter to the power supply via the USB-C charging cable.
2. Disconnect the power after it is fully charged.

LED Flashlight

Press and hold the switch button for 3 seconds to turn on the LED light. Short presses cycle through SOS, strobe, and off modes.

Jump Start Your Car

This product is suitable for 12V vehicles only. Ensure the remaining power is at least 80% before attempting to start the car.

1. Insert the clamp plug completely into the product's jump clamp port.
2. Connect the red clamp to the positive (+) battery terminal and the black clamp to the negative (-) battery terminal.
3. Turn on the car engine to start the vehicle.
4. Once the vehicle has started, remove the jumper cable from the jump starter and the vehicle battery.

Indicator and troubleshooting

• "E1" - Low temperature charging protection: Charging will stop. Protection is automatically released when the temperature rises above 2°C.
• "E2" - High temperature charging protection: Charging will stop. Protection is automatically released when the temperature is lower than 45°C.
• "E3" - High temperature discharge protection: Charging will stop. Protection is automatically released when the temperature is lower than 65°C.

Maintenance

• Do not use the product to start an already expanded car battery.
• Store the product in a cool, well-ventilated place.
• Handle the product carefully to avoid dropping or impact.
• Do not disassemble or modify the product.
• Do not use detergent to clean the product.
• Avoid prolonged exposure to high temperatures. The operating temperature is -20°C to 60°C (-4°F to 140°F). Storage temperature should not exceed 50°C (122°F).
• Check the battery level at least every three months and recharge as needed.
• Keep away from children and pets.

Trouble Shooting

Q: How can I turn off the product?
A: The product automatically powers off when no load is detected or charging is complete.

Q: What is the storage temperature of this product?
A: The product uses a lithium polymer battery with an operating temperature of -20°C to 60°C (-4°F to 140°F). Storing above 60°C (140°F) can damage the battery. Do not store in vehicles parked in hot weather for extended periods.

Q: How do you know if this unit is connected to the vehicle correctly?
A: When the battery clamps are connected to the vehicle battery, a steady green light on the jumper cable indicator signifies a correct connection. A solid red light with beeping indicates a reverse connection.

Q: What should I do if this product can't start a vehicle?
A: Recharge the unit fully. Try pressing the "BOOST" button on the jumper cable and wait for a solid green light before starting the vehicle within 30 seconds. If it still does not work, contact support@dyeetic.com with your order ID.

Warranty

For any issues or malfunctions during use, please email your question and order number to support@dyeetic.com. Dyeetic will provide after-sales service within 24 hours.